VDSS = ± 60 V, ID(DC) = ± 6 A 3-phase Motor Drive Inverter SMA5135 Features Package ● V(BR)DSS -------------------------------- ± 60 V (ID = 100 μA) ● ID ---------------------------------------------------------- ± 6A ● RDS(ON) ------------------------------------------- 0.22 Ω max. ● Built-in three half bridge circuit configured by P-channel MOSFET and N-channel MOSFET ● Low On Resistance ● ESD protection Zener with each Gate ● Compliant with RoHS directive SIP12 (SMA-12) (1) (12) Not to scale Applications ● 3-phase DC Motor Driver Equivalent circuit Absolute Maximum Ratings Unless otherwise specified, TA = 25 °C Characteristic Symbol Test conditions Rating N-channel P-channel MOSFET MOSFET 60 −6 0 Unit Drain to Source Voltage VDSS Gate to Source Voltage VGSS ±20 ±20 V Continuous Drain Current ID(DC) 6 −6 A 10 −10 A Pulsed Drain Current Maximum Allowable Power Dissipation ID(PULSE) PT θj-a Thermal Resistance θj-c PW ≤ 1 ms Duty cycle ≤25 % No.Fin Ta=25°C All Element Operation Tc=25°C All Element Operation Junction-to-Ambient All Element Operation Junction-to-Case All Element Operation V 4 W 29 31.25 °C/W 4.31 °C/W Channel Temperature Tch 150 °C Storage Temperature Tstg −40 to 150 °C SMA5135 – DSE Rev.1.1 Apr. 13, 2016 SANKEN ELECTRIC CO.,LTD. 1 SMA5135 Electrical Characteristics Unless otherwise specified, TA = 25 °C Parameter Symbol Test Conditions Min. Typ. Max. Unit N-channel MOSFET Drain to Source Breakdown Voltage Drain to Source Leakage Current V(BR)DSS ID = 100 μA, VGS = 0 V 60 − − V IDSS VDS = 60 V, VGS = 0 V − − 100 µA Gate to Source Leakage Current IGSS VGS = ± 20 V − − ± 10 µA Gate Threshold Voltage VTH VDS = 10 V, ID = 250 μA 1.0 − 2.0 V Forward Transconductance Re(yfs) VDS = 10 V, ID = 3 A − 5.5 − S Static Drain to Source On-State RDS(ON) ID = 3 A, VGS = 4 V − − 0.22 Ω − 320 − − 160 − − 35 − − 16 − − 65 − − 70 − − 45 − Input Capacitance Ciss Output Capacitance Coss Reverse Transfer Capacitance Crss Turn-On Delay Time td(on) Rise Time Turn-Off Delay Time Fall Time Source to Drain Diode Forward Voltage Source to Drain Diode Reverse Recovery Time tr td(off) VDS = 10 V VGS = 0 V f = 1 MHz VDD ≒ 20 V ID = 3 A VGS = 5 V, RL = 6.67 Ω tf pF ns VSD IS = 6A, VGS = 0 V − 1.2 − V trr ISD = 3 A, VGS = 0 V di/dt = 100 A/µs − 65 − ns P-channel MOSFET Drain to Source Breakdown Voltage Drain to Source Leakage Current V(BR)DSS ID = − 100 μA, VGS = 0 V − 60 − − V IDSS VDS = − 60 V, VGS = 0 V − − − 100 µA Gate to Source Leakage Current IGSS − − ± 10 µA Gate Threshold Voltage VTH − 1.0 − − 2.0 V − 6.0 − S − − 0.22 Ω − 790 − − 310 − − 90 − − 40 − − 110 − − 160 − − 80 − Forward Transconductance Re(yfs) VGS = ± 20 V VDS = − 10 V, ID = − 250 μA VDS = − 10 V, ID = − 3 A Static Drain to Source On-State RDS(ON) ID = − 3 A, VGS = − 10 V Input Capacitance Ciss Output Capacitance Coss Reverse Transfer Capacitance Crss Turn-On Delay Time td(on) Rise Time Turn-Off Delay Time Fall Time Source to Drain Diode Forward Voltage Source to Drain Diode Reverse Recovery Time SMA5135 – DSE Rev.1.1 Apr. 13, 2016 tr td(off) VDS = − 10 V VGS = 0 V f = 1 MHz VDD ≒− 20 V ID = − 3 A VGS = − 5 V, RL = 6.67 Ω tf pF ns VSD IS = − 6A, VGS = 0 V − − 1.1 − V trr ISD = − 3 A, VGS = 0 V di/dt = 100 A/µs − 85 − ns SANKEN ELECTRIC CO.,LTD. 2 SMA5135 Typical Characteristics Figure 1 ID vs. VDS Characteristics (N-channel) Figure 2 ID vs. VDS Characteristics (P-channel) Figure 3 ID vs. VGS Characteristics (N-channel) Figure 4 ID vs. VGS Characteristics (P-channel) SMA5135 – DSE Rev.1.1 Apr. 13, 2016 SANKEN ELECTRIC CO.,LTD. 3 SMA5135 Figure 5 Figure 7 RDS(ON) vs. ID Characteristics (N-channel) Re(yfs) vs. ID Characteristics (N-channel) SMA5135 – DSE Rev.1.1 Apr. 13, 2016 Figure 6 Figure 8 RDS(ON) vs. ID Characteristics (P-channel) Re(yfs) vs. ID Characteristics (P-channel) SANKEN ELECTRIC CO.,LTD. 4 SMA5135 Figure 9 RDS(ON) vs. ID Characteristics (N-channel) Figure 11 Capacitance vs. VDS Characteristics (N-channel) SMA5135 – DSE Rev.1.1 Apr. 13, 2016 Figure 10 RDS(ON) vs. ID Characteristics (P-channel) Figure 12 SANKEN ELECTRIC CO.,LTD. Capacitance vs. VDS Characteristics (P-channel) 5 SMA5135 Figure 13 IDR vs. VSD Characteristics (N-channel) Figure 15 Safe Operating Area (N-channel) SMA5135 – DSE Rev.1.1 Apr. 13, 2016 Figure 14 IDR vs. VSD Characteristics (P-channel) Figure 16 SANKEN ELECTRIC CO.,LTD. Safe Operating Area (P-channel) 6 SMA5135 Derating Curve All Element Operation Figure 17 PT vs. TA Derating Curve SMA5135 – DSE Rev.1.1 Apr. 13, 2016 SANKEN ELECTRIC CO.,LTD. 7 SMA5135 Package Outline ● SIP12(SMA-12) NOTES: ● Dimension is in millimeters. ● Pin treatment Pb-free. Device composition compliant with the RoHS directive. Marking Diagram JAPAN YMDD SMA5135 (1) (12) Lot Number: Y is the last digit of the year of manufacture (0 to 9) M is the month of the year (1 to 9, O, N or D) DD is the day of the month (01 to 31) Part Number SMA5135 – DSE Rev.1.1 Apr. 13, 2016 SANKEN ELECTRIC CO.,LTD. 8 SMA5135 IMPORTANT NOTES ● All data, illustrations, graphs, tables and any other information included in this document as to Sanken’s products listed herein (the “Sanken Products”) are current as of the date this document is issued. All contents in this document are subject to any change without notice due to improvement of the Sanken Products, etc. Please make sure to confirm with a Sanken sales representative that the contents set forth in this document reflect the latest revisions before use. ● The Sanken Products are intended for use as components of general purpose electronic equipment or apparatus (such as home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). Prior to use of the Sanken Products, please put your signature, or affix your name and seal, on the specification documents of the Sanken Products and return them to Sanken. When considering use of the Sanken Products for any applications that require higher reliability (such as transportation equipment and its control systems, traffic signal control systems or equipment, disaster/crime alarm systems, various safety devices, etc.), you must contact a Sanken sales representative to discuss the suitability of such use and put your signature, or affix your name and seal, on the specification documents of the Sanken Products and return them to Sanken, prior to the use of the Sanken Products. The Sanken Products are not intended for use in any applications that require extremely high reliability such as: aerospace equipment; nuclear power control systems; and medical equipment or systems, whose failure or malfunction may result in death or serious injury to people, i.e., medical devices in Class III or a higher class as defined by relevant laws of Japan (collectively, the “Specific Applications”). Sanken assumes no liability or responsibility whatsoever for any and all damages and losses that may be suffered by you, users or any third party, resulting from the use of the Sanken Products in the Specific Applications or in manner not in compliance with the instructions set forth herein. ● In the event of using the Sanken Products by either (i) combining other products or materials therewith or (ii) physically, chemically or otherwise processing or treating the same, you must duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility. ● Although Sanken is making efforts to enhance the quality and reliability of its products, it is impossible to completely avoid the occurrence of any failure or defect in semiconductor products at a certain rate. You must take, at your own responsibility, preventative measures including using a sufficient safety design and confirming safety of any equipment or systems in/for which the Sanken Products are used, upon due consideration of a failure occurrence rate or derating, etc., in order not to cause any human injury or death, fire accident or social harm which may result from any failure or malfunction of the Sanken Products. Please refer to the relevant specification documents and Sanken’s official website in relation to derating. ● No anti-radioactive ray design has been adopted for the Sanken Products. ● No contents in this document can be transcribed or copied without Sanken’s prior written consent. ● The circuit constant, operation examples, circuit examples, pattern layout examples, design examples, recommended examples, all information and evaluation results based thereon, etc., described in this document are presented for the sole purpose of reference of use of the Sanken Products and Sanken assumes no responsibility whatsoever for any and all damages and losses that may be suffered by you, users or any third party, or any possible infringement of any and all property rights including intellectual property rights and any other rights of you, users or any third party, resulting from the foregoing. ● All technical information described in this document (the “Technical Information”) is presented for the sole purpose of reference of use of the Sanken Products and no license, express, implied or otherwise, is granted hereby under any intellectual property rights or any other rights of Sanken. ● Unless otherwise agreed in writing between Sanken and you, Sanken makes no warranty of any kind, whether express or implied, including, without limitation, any warranty (i) as to the quality or performance of the Sanken Products (such as implied warranty of merchantability, or implied warranty of fitness for a particular purpose or special environment), (ii) that any Sanken Product is delivered free of claims of third parties by way of infringement or the like, (iii) that may arise from course of performance, course of dealing or usage of trade, and (iv) as to any information contained in this document (including its accuracy, usefulness, or reliability). ● In the event of using the Sanken Products, you must use the same after carefully examining all applicable environmental laws and regulations that regulate the inclusion or use of any particular controlled substances, including, but not limited to, the EU RoHS Directive, so as to be in strict compliance with such applicable laws and regulations. ● You must not use the Sanken Products or the Technical Information for the purpose of any military applications or use, including but not limited to the development of weapons of mass destruction. In the event of exporting the Sanken Products or the Technical Information, or providing them for non-residents, you must comply with all applicable export control laws and regulations in each country including the U.S. Export Administration Regulations (EAR) and the Foreign Exchange and Foreign Trade Act of Japan, and follow the procedures required by such applicable laws and regulations. ● Sanken assumes no responsibility for any troubles, which may occur during the transportation of the Sanken Products including the falling thereof, out of Sanken’s distribution network. ● Although Sanken has prepared this document with its due care to pursue the accuracy thereof, Sanken does not warrant that it is error free and Sanken assumes no liability whatsoever for any and all damages and losses which may be suffered by you resulting from any possible errors or omissions in connection with the contents included herein. ● Please refer to the relevant specification documents in relation to particular precautions when using the Sanken Products, and refer to our official website in relation to general instructions and directions for using the Sanken Products. DSGN-CEZ-16001 SMA5135 – DSE Rev.1.1 Apr. 13, 2016 SANKEN ELECTRIC CO.,LTD. 9