rBOX630 Robust Din-rail Fanless Embedded System with RISC-based (i.MX 6) Processor 4 COM, 2 CAN Bus and DIO NEW 3 Antenna hole (for 3G/GPRS/Wi-Fi) 2 LAN Features ● Fanless design ● RISC-based module (i.MX 6) processor ● 1 GB DDR3 SDRAM onboard ● 4 GB eMMC onboard ● Completed industrial AP development software ● Wide range DC power input (12 - 48V) with terminal block ● Ready-to-run embedded Linux operating system ● Wide temperature operation of -40°C ~ +70°C 1 HDMI (Support screw lock) 4 COM 2 CAN Bus 1 Console port 1 Power DC-in SD/SIM Card Socket Front view Din-rail kit Fanless Low Power 1 DIO (8 IN/ 8 OUT) 1 OTG USB Easy-to-access interface Rear view Freescale i.MX 6 EN60950 Isolation Ext. Temp IP30 Introduction The rBOX630 cost-effective din-rail fanless embedded system utilizes the low power RISC-based module (i.MX 6) processor and is designed to withstand temperatures ranging from -40°C to +70°C for using in harsh environment and industrial automation applications. The rBOX630 features 4 RS-232/422/485 serial ports, dual LANs, 8 digital input channels, 8 digital output channels, 2 CAN bus and 1 eMMC onboard 4 GB & 1 x SDHC socket for storage expansion (easy to access) in a compact, IP30 protected, industrial-strength robust case. Two power paths input minimize the risk of data loss in the event of a single power failure. Its vertical din-rail form factor makes it easy to install the system in a small cabinet. Because of ARM's low power consumption architecture, rBOX630 generate little heat while being operated. The ready-to-run rBOX630 is specially designed for industrial machine, automatic parking lot, traffic cabinet and more. System I/O Outlet HDMI USB CAN DIO Hardware Specifications Standard Color Construction CPU System Board System Memory System I/O Outlet Sliver-Black Extruded aluminum and heavy-duty steel, IP30 i.MX 6, Cortex-A9 RISC CPU, 800MHz Q7M120 1 GB DDR3 Onboard Serial Port 4 x RS-232/422/485 (COM 1 ~ 4) COM 1~4 with TX/RX/RTS/CTS signals RS-232/422/485 interface select by software LAN 1 x 10/100/1000Mbps , 1 x 10/100Mbps Ethernet Magnetic isolation protection 1.5KV Console Port RTC Alarm Contact 353 1 x HDMI (Support screw lock) 1 x USB 2.0 OTG 2 CAN 2.0 B (Phoenix connector, non-isolation) Meets ISO 11898 standard Software control termination resistor 120 ohm can high speed up to 1Mbit/s for transmit/receive 1 x DIO ( 8 IN/ 8 OUT ) with Isolation 2KV DI : Wet/Dry DO : Wet DI : Input channels : 8, source type Input voltage : 0 to 30VDCDigital input levels for dry contacts : -Logic level 0: close to GND -Logic level 1: open Digital input levels for wet contacts : -Logic level 0: +10V to +24V (DI to COM-) -Logic level 1: +3V max. DO : Output channels : 8, sink type Output current: Max. 200 mA per channel On-state voltage : 24VDC nominal, open collector to 30V Optical isolation protection 2 KV DB9 connector For user setting with debug Battery onboard Provides power for the internal real time clock & calendar Ideal for vibration environment & reduces maintenance efforts One relay output with current 0.5A@30VDC * All specifications and photos are subject to change without notice. Hardware Specifications Ordering Information System I/O Outlet Standard rBOX630-FL-DC Wireless Watchdog Timer LEDs Storage Installation Power Supply Operating Temperature Storage Temperature Humidity Vibration Endurance Weight (net/gross) Dimensions EOS Support Certification 1 x Mini card socket (supports USB interface) with 1 x SIM Socket by outside access and is easy plug/pull. 1 x Mini card socket (supports USB&PCIE interface) with 1 x SIM Socket by inside WDT 1: one step is 1 sec, 255 levels System Power, Alarm, Ready/Active, COM (TX, RX), Wireless Alarm DC PWR1 or PWR2 1 x eMMC 4 GB onboard (for boot disk) Supports 1 x SDHC Card (easy-to-access, for store only.) Din-rail Wall mount Power Input 2 power paths with terminal block Power Input Range 12-48VDC Power Input Rating 12-48VDC, 0.74-0.23A Power Protection DC Version: OVP (Over voltage protection) UVP (Under voltage protection) Reverse protection -40°C ~ +70°C (-40°F ~ +158°F) -45°C ~ +85°C (-49°F ~ +185°F) 10% ~ 95% 5G @ 10-150Hz, amplitude 0.35ms 0.9 kg (2 lb)/1.3kg (2.87 lb) 55 mm (2.16") (W) x 155 mm (6.10") (D) x 110 mm (4.33") (H) Linux Host OS/ Development OS : Ubuntu 12.04 Yocto Dora LTS Toolchain/ Cross compiler : Freescale LTIB Kernel : 3.0.35 (with Freescale and Axiomtek hardware modified patch) FCC Part 18 Heavy Industrial CE Robust din-rail fanless embedded system with Q7-RISC module (i.MX 6), 4 COM, 2 CAN and DIO (-40°C ~ +70°C) Optional Wall mount kit Wireless (3G/GPS or Wi-Fi) module Overview Embedded Systems Embedded Systems for Transportation 3 Embedded Field Controllers Industrial Firewall Digital Signage Solutions Embedded MicroBoxes Dimensions Industrial Barebone Systems Industrial Chassis Backplanes Power Supplies Peripherals & Accessories * All specifications and photos are subject to change without notice. a x i o m te k . c o m © 2016 Axiomtek Co., Ltd. All rights reserved. 354