HIP6501A ® Data Sheet December 30, 2004 Triple Linear Power Controller with ACPI Control Interface The HIP6501A, paired with either the HIP6020 or HIP6021, simplifies the implementation of ACPI-compliant designs in microprocessor and computer applications. The IC integrates two linear controllers and a low-current pass transistor, as well as the monitoring and control functions into a 16-pin SOIC package. One linear controller generates the 3.3VDUAL voltage plane from an ATX power supply’s 5VSB output during sleep states (S3, S4/S5), powering the PCI slots through an external pass transistor, as instructed by the status of the 3.3VDUAL enable pin. An additional pass transistor is used to switch in the ATX 3.3V output for PCI operation during S0 and S1 (active) operatingstates. The second linear controller supplies the computer system’s 2.5V/3.3V memory power through an external pass transistor in active states. During S3 state, an integrated pass transistor supplies the 2.5V/3.3V sleep-state power. A third controller powers up a 5VDUAL plane by switching in the ATX 5V output in active states, or the ATX 5VSB in sleep states. The HIP6501A’s operating mode (active-state outputs or sleep-state outputs) is selectable through two control pins: S3 and S5. Further control of the logic governing activation of different power modes is offered through two enabling pins: EN3VDL and EN5VDL. In active states, the 3.3VDUAL linear regulator uses an external N-Channel pass MOSFET to connect the output (VOUT1) directly to the 3.3V input supplied by an ATX (or equivalent) power supply, while incurring minimal losses. In sleep state, the 3.3VDUAL output is supplied from the ATX 5VSB through an NPN transistor, also external to the controller. Active state power delivery for the 2.5/3.3VMEM output is done through an external NPN transistor, or an NMOS switch for the 3.3V setting. In sleep states, conduction on this output is transferred to an internal pass transistor. The 5VDUAL output is powered through two external MOS transistors. In sleep states, a PMOS (or PNP) transistor conducts the current from the ATX 5VSB output, while in active states, current flow is transferred to an NMOS transistor connected to the ATX 5V output. Similar to the 3.3VDUAL output, the operation of the 5VDUAL output is dictated not only by the status of the S3 and S5 pins, but that of the EN5VDL pin as well. FN4749.6 Features • Provides 3 ACPI-Controlled Voltages - 5V Active/Sleep (5VDUAL) - 3.3V Active/Sleep (3.3VDUAL) - 2.5V/3.3V Active/Sleep (2.5VMEM) • Simple Control Design - No Compensation Required • Excellent Output Voltage Regulation - 3.3VDUAL Output: ±2.0% Over Temperature; Sleep States Only - 2.5V/3.3V Output: ±2.0% Over Temperature; Both Operational States (3.3V setting in sleep only) • Fixed Output Voltages Require No Precision External Resistors • Small Size - Small External Component Count • Selectable 2.5VMEM Output Voltage Via FAULT/MSEL Pin - 2.5V for RDRAM Memory - 3.3V for SDRAM Memory • Under-Voltage Monitoring of All Outputs with Centralized FAULT Reporting • Adjustable Soft-Start Function Eliminates 5VSB Perturbations • Pb-Free Available (RoHS Compliant) Pinout HIP6501A (SOIC) TOP VIEW 16 VSEN2 5VSB 1 15 DRV2 EN3VDL 2 3V3DLSB 3 14 12V 13 SS 3V3DL 4 12 5VDL EN5VDL 5 S3 6 11 5VDLSB S5 10 DLA 7 GND 8 9 FAULT/MSEL Ordering Information PART NUMBER TEMP. RANGE (°C) PACKAGE PKG. DWG. # HIP6501ACB 0 to 70 16 Ld SOIC M16.15 HIP6501ACBZ (Note) 0 to 70 16 Ld SOIC (Pb-free) M16.15 HIP6501AEVAL1 Evaluation Board *Add “-T” suffix to part number for tape and reel packaging. NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD020. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2004. All Rights Reserved All other trademarks mentioned are the property of their respective owners. Block Diagram 12V 3V3DL 3V3DLSB 5VSB TO 12V EA4 12V BIAS + - 5VSB POR 4.5V/4.0V 2 12V MONITOR 10.8V/9.0V DLA 5VDLSB HIP6501A FAULT/MSEL MONITOR AND CONTROL UV DETECTOR TEMPERATURE MONITOR (TMON) + 40µA + MEM VOLTAGE 0.2V SELECT COMP + 1.265V - DRV2 TO UV DETECTOR 5VDL + + 3.75V - EA2 + UV COMPARATOR DELAY 10µA VSEN2 FN4749.6 December 30, 2004 SS EN3VDL S3 S5 EN5VDL FIGURE 1. GND HIP6501A Simplified Power System Diagram +5VIN +12VIN +5VSB +3.3VIN Q1 LINEAR CONTROLLER 2.5VMEM Q2 LINEAR CONTROLLER Q3 HIP6501A Q4 3.3VDUAL Q5 CONTROL LOGIC 5VDUAL FAULT SHUTDOWN S3 S5 EN5VDL EN3VDL FIGURE 2. Typical Application +5VIN +12VIN +5VSB +3.3VIN 12V 5VSB DRV2 3V3DLSB Q2 VSEN2 Q3 VOUT1 Q1 VOUT2 3V3DL 3.3VDUAL COUT1 2.5/3.3VMEM COUT2 FAULT/MSEL RSEL HIP6501A FAULT Q4 S3 SLP_S3 5VDLSB S5 SLP_S5 DLA Q5 EN5VDL EN5VDL SS CSS SHUTDOWN VOUT3 5VDL EN3VDL EN3VDL COUT3 5VDUAL GND FIGURE 3. 3 FN4749.6 December 30, 2004 HIP6501A Absolute Maximum Ratings Thermal Information Supply Voltage, V5VSB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V 12V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +14.5V DLA, DRV2 . . . . . . . . . . . . . . . . . . . . . . .GND - 0.3V to V12V +0.3V All Other Pins . . . . . . . . . . . . . . . . . . . . .GND - 0.3V to 5VSB + 0.3V ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 3 [5kV] Thermal Resistance (Typical, Note 1) θJA (°C/W) SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C (SOIC - Lead Tips Only) Recommended Operating Conditions Supply Voltage, V5VSB . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V ±5% Secondary Bias Voltage, V12V . . . . . . . . . . . . . . . . . . . . +12V ±10% Digital Inputs, VS3, VS5, VEN3VDL, VEN5VDL . . . . . . . . . .0 to +5.5V Ambient Temperature Range . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Junction Temperature Range. . . . . . . . . . . . . . . . . . . . 0°C to 125°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications Recommended Operating Conditions, Unless Otherwise Noted. Refer to Figures 1, 2 and 3 PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS VCC SUPPLY CURRENT - 20 - mA - 10 - mA Rising 5VSB POR Threshold - - 4.5 V 5VSB POR Hysteresis - 0.2 - V Rising 12V Threshold - - 10.8 V Soft-Start Current - 10 - µA Shutdown Soft-Start Voltage - - 0.8 V - - 2.0 % Operating Supply Current I5VSB Shutdown Supply Current I5VSB(OFF) VSS = 0.8V, S3 = 0, S5 = 0 POWER-ON RESET, SOFT-START, AND 12V MONITOR 2.5V/3.3V LINEAR REGULATOR (VOUT2) Regulation VSEN2 Nominal Voltage Level VVSEN2 RSEL = 1kΩ - 2.5 - V VSEN2 Nominal Voltage Level VVSEN2 RSEL = 10kΩ - 3.3 - V VSEN2 Under-voltage Rising Threshold - 75 - % VSEN2 Under-voltage Hysteresis - 6 - % VSEN2 Output Current IVSEN2 5VSB = 5V 250 300 - mA DRV2 Output Drive Current IDRV2 5VSB = 5V, RSEL = 1kΩ 20 30 - mA - 200 - Ω - - 2.0 % - 3.3 - V 3V3DL Under-voltage Rising Threshold - 2.450 - V 3V3DL Under-voltage Hysteresis - 200 - mV 5.0 8.5 - mA - 90 - Ω RSEL = 10kΩ DRV2 Output Impedance 3.3VDUAL LINEAR REGULATOR (VOUT1) Sleep-Mode Regulation 3V3DL Nominal Voltage Level V3V3DL 3V3DLSB Output Drive Current I3V3DLSB DLA Output Impedance 4 5VSB = 5V FN4749.6 December 30, 2004 HIP6501A Electrical Specifications Recommended Operating Conditions, Unless Otherwise Noted. Refer to Figures 1, 2 and 3 (Continued) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS - 3.750 - V 5VDUAL SWITCH CONTROLLER (VOUT3) 5VDL Under-Voltage Rising Threshold 5VDL Under-Voltage Hysteresis - 260 - mV -20 - -40 mA - 350 - Ω 40 50 60 ms Maximum Allowable S3 to S5 Skew - 200 - µs 5VSB POR Extension Past Threshold Voltage - 3.3 - ms 5VDLSB Output Drive Current I5VDLSB 5VDLSB = 4V 5VDLSB Pull-up Impedance to 5VSB TIMING INTERVALS Active State Assessment Past 12V Threshold Note 2 CONTROL I/O (S3, S5, EN3VDL, EN5VDL, FAULT) High Level Threshold - - 2.2 V Low Level Threshold 0.8 - - V S3,S5 Internal Pull-up Impedance to 5VSB FAULT Output Impedance FAULT = high FAULT Under-Voltage Reporting Delay - 70 - kΩ - 100 - Ω - 10 - µs TEMPERATURE MONITOR Fault-Level Threshold Note 3 125 - - °C Shutdown-Level Threshold Note 3 - 150 - °C NOTES: 2. Guaranteed by Correlation. 3. Guaranteed by Design. Functional Pin Description EN3VDL and EN5VDL (Pins 2 and 5) Provide a 5V bias supply for the IC to this pin by connecting it to the ATX 5VSB output. This pin also provides the base bias current for all the external NPN transistors controlled by the IC. The voltage at this pin is monitored for power-on reset (POR) purposes. These pins control the logic governing the output behavior in response to S3 and S4/S5 requests. These are digital inputs whose status can only be changed during active states operation or during chip shutdown (SS pin grounded by external open-drain device). The input information is latched-in when entering a sleep state, as well as following 5VSB POR release or exit from shutdown. GND (Pin 8) FAULT/MSEL (Pin 9) Signal ground for the IC. All voltage levels are measured with respect to this pin. This is a multiplexed function pin allowing the setting of the memory output voltage to either 2.5V or 3.3V (for RDRAM or SDRAM memory systems). The memory voltage setting is latched-in 3ms (typically) after 5VSB POR release. In case of an under-voltage on any of the outputs or an overtemperature event, this pin is used to report the fault condition by being pulled to 5VSB. 5VSB (Pin 1) S3 and S5 (Pins 6 and 7) These pins switch the IC’s operating state from active (S0, S1) to S3 and S4/S5 sleep states. Connect S3 to SLP_S3 and S5 to SLP_S5. These are digital inputs featuring internal 70kΩ (typical) resistor pull-ups to 5VSB. Internal circuitry deglitches the S3 pin for disturbances. Additional circuitry blocks any illegal state transitions (such as S3 to S4/S5 or vice versa). When entering an S4/S5 sleep state, the S3 signal is allowed to go low as far as 200µs (typically) ahead of the S5 signal. 5 SS (Pin 13) Connect a small ceramic capacitor (allowable range: 5nF0.22µF; 0.1µF recommended) from this pin to GND. The internal Soft-Start (SS) current source along with the external capacitor creates a voltage ramp used to control the ramp-up of the output voltages. Pulling this pin low with an open-drain device shuts down all the outputs as well as FN4749.6 December 30, 2004 HIP6501A forces the FAULT pin low. The CSS capacitor is also used to provide a controlled voltage slew rate during active-to-sleep transitions on the 3.3VDUAL and 2.5/3.3VMEM outputs. 12V (Pin 14) Connect this pin to the ATX (or equivalent) 12V output. This pin is used to monitor the status of the power supply as well as provide bias for the NMOS-compatible output drivers. 12V presence at the chip in the absence of bias voltage, or severe 12V brownout during active states (S0, S1) operation can lead to chip misbehavior. VSEN2 (Pin 16) Connect this pin to the memory output (VOUT2). In sleep states, this pin is regulated to 2.5V or 3.3V (based on RSEL) through an internal pass transistor capable of delivering 300mA (typically). When VOUT2 is programmed to 2.5V, the active-state voltage at this pin is regulated through an external NPN transistor connected at the DRV2 pin. For the 3.3V setting, the ATX 3.3V is passed to this pin through a fully on N-MOS transistor. During all operating states, the voltage at this pin is monitored for under-voltage events. DRV2 (Pin 15) For the 2.5V RDRAM systems, connect this pin to the base of a suitable NPN transistor. This pass transistor regulates the 2.5V output from the ATX 3.3V during active states operation. For 3.3V SDRAM systems connect this pin to the gate of a suitable N-MOS transistor; this transistor is used to switch in the ATX 3.3V output. 3V3DL (Pin 4) Connect this pin to the 3.3V dual output (VOUT1). In sleep states, the voltage at this pin is regulated to 3.3V; in active states, ATX 3.3V output is delivered to this node through a fully on N-MOS transistor. During all operating states, this pin is monitored for under-voltage events. 5VDLSB (Pin 11) Connect this pin to the gate of a suitable P-MOSFET or bipolar PNP. In sleep states, this transistor is switched on, connecting the ATX 5VSB output to the 5VDUAL regulator output. Description Operation The HIP6501A controls 3 output voltages (Refer to Figures 1, 2, and 3). It is designed for microprocessor computer applications with 3.3V, 5V, 5VSB, and 12V outputs from an ATX power supply. The IC is composed of two linear controllers supplying the PCI slots’ 3.3VAUX power (3.3VDUAL, VOUT1) and the 2.5V RDRAM or 3.3V SDRAM memory power (2.5/3.3VMEM, VOUT2), and a dual switch controller supplying the 5VDUAL voltage (VOUT3). In addition, all the control and monitoring functions necessary for complete ACPI implementation are integrated into the HIP6501A. Initialization The HIP6501A automatically initializes upon receipt of input power. The Power-On Reset (POR) function continually monitors the 5VSB input supply voltage, initiating soft-start operation after it exceeds its POR threshold (in either S3 or S4/S5 states). To ensure stabilization of the 5VSB supply before operation is allowed, POR is released 3.3ms (typically) after 5VSB exceeds the POR threshold. The 5VSB POR trip event is also used to lock in the memory voltage setting based on RSEL. Operational Truth Tables The EN3VDL and EN5VDL pins offer a host of choices in terms of the overall system architecture and supported features. Tables 1-3 describe the truth combinations pertaining to each of the three outputs. TABLE 1. 3.3VDUAL OUTPUT (VOUT1) TRUTH TABLE 3V3DLSB (Pin 3) EN3VDL S5 S3 3V3DL 0 1 1 3.3V S0, S1 STATES (Active) 0 1 0 3.3V S3 0 0 1 0 0 0 3.3V S4/S5 1 1 1 3.3V S0, S1 STATES (Active) 1 1 0 3.3V S3 5VDL (Pin 12) 1 0 1 Connect this pin to the 5VDUAL output (VOUT3). In either operating state, the voltage at this pin is provided through a fully on MOS transistor. This pin is also monitored for undervoltage events. 1 0 0 Connect this pin to the base of a suitable NPN transistor. In sleep states, this transistor is used to regulate the voltage at the 3V3DL pin to 3.3V. DLA (Pin 10) Connect this pin to the gates of suitable N-MOSFETs, which in active states, are used to switch in the ATX 3.3V and 5V outputs into the 3.3VDUAL and 5VDUAL outputs, respectively. COMMENTS Note 4 Maintains Previous State Note 4 Maintains Previous State 0V S4/S5 NOTE: 4. Combination not allowed. As seen in Table 1, EN3VDL simply controls whether the 3.3VDUAL plane remains powered up during S4/S5 sleep state. 6 FN4749.6 December 30, 2004 HIP6501A TABLE 2. 5VDUAL OUTPUT (VOUT3) TRUTH TABLE 5VSB EN5VDL S5 S3 5VDL COMMENTS 0 1 1 5V S0, S1 STATES (Active) 0 1 0 0V S3 0 0 1 0 0 0 0V S4/S5 1 1 1 5V S0, S1 STATES (Active) 1 1 0 5V S3 1 0 1 1 0 0 S5 Note 5 Maintains Previous State 12V 3V3DLSB DLA Note 5 Maintains Previous State 5V S3 S4/S5 3V3DL 5VDLSB NOTE: 5VDL 5. Combination not allowed. Very similarly, Table 2 details the fact that EN5VDL status controls whether the 5VDUAL plane supports sleep states. FIGURE 4. 3VDUAL AND 5VDUAL TIMING DIAGRAM FOR EN3VDL = 1, EN5VDL = 1 TABLE 3. 2.5/3.3VMEM OUTPUT (VOUT2) TRUTH TABLE RSEL S5 S3 2.5/3.3VMEM COMMENTS 1kΩ 1 1 2.5V S0, S1 STATES (Active) 1kΩ 1 0 2.5V S3 1kΩ 0 1 Note 6 1kΩ 0 0 0V 10kΩ 1 1 3.3V S0, S1 STATES (Active) 10kΩ 1 0 3.3V S3 10kΩ 0 1 Note 6 10kΩ 0 0 0V Maintains Previous State S4/S5 Maintains Previous State S4/S5 NOTE: 5VSB S3 S5 12V 3V3DLSB DLA 3V3DL 5VDLSB 6. Combination not allowed. 5VDL As seen in Table 3, 2.5/3.3VMEM output is maintained in S3 (Suspend-To-RAM), but not in S4/S5 state. The dual-voltage support accommodates both SDRAM as well as RDRAM type memories. Additionally, the internal circuitry does not allow the transition from an S3 (suspend to RAM) state to an S4/S5 (suspend to disk/soft off) state or vice versa. The only ‘legal’ transitions are from an active state (S0, S1) to a sleep state (S3, S4/S5) and vice versa. Functional Timing Diagrams Figures 4-8 are timing diagrams, detailing the power up/down sequences of all three outputs in response to the status of the enable (EN3VDL, EN5VDL) and sleep-state pins (S3, S5), as well as the status of the ATX supply. FIGURE 5. 3VDUAL AND 5VDUAL TIMING DIAGRAM FOR EN3VDL = 1, EN5VDL = 0 Not shown in these diagrams is the de-glitching feature used to protect against false sleep state tripping. Once the status of the S3 pin changes, an internal timer is activated. If at the end of the timeout period (typically 200µs) the input pins present a valid state change request, then the controller transitions to the new configuration. Otherwise, the previously attained valid state is maintained until valid control signals are received from the system. This particular feature is useful in noisy computer environments if the control signals have to travel over significant distances. The status of the EN3VDL and EN5VDL pins can only be changed while in active (S0, S1) states, when the bias supply (5VSB pin) is below POR level, or during chip shutdown (SS pin shorted to GND); a status change of these two pins while in a sleep state is ignored. 7 FN4749.6 December 30, 2004 HIP6501A Soft-Start Circuit 5VSB Soft-Start into Sleep States (S3, S4/S5) The 5VSB POR function initiates the soft-start sequence. An internal 10µA current source charges an external capacitor to 5V. The error amplifiers reference inputs are clamped to a level proportional to the SS (Soft-Start) pin voltage. As the SS pin voltage slews from about 1.25V to 2.5V, the input clamp allows a rapid and controlled output voltage rise. S3 S5 12V 3V3DLSB DLA 3V3DL 5VDLSB 5VDL FIGURE 6. 3VDUAL AND 5VDUAL TIMING DIAGRAM FOR EN3VDL = 0, EN5VDL = 1 5VSB S3 S5 12V 3V3DLSB DLA Figure 9 shows the soft-start sequence for the typical application start-up in a sleep state with all output voltages enabled. At time T0 5VSB (bias) is applied to the circuit. At time T1, 5VSB surpasses POR level, and an internal fast charge circuit quickly raises the SS capacitor voltage to approximately 1V. At this point, the 10µA current source continues the charging up to T2, where a voltage of 1.25V (typically) is reached and an internal clamp limits further charging. Clamping of the soft-start voltage (T2 to T3 interval) should only be noticed with capacitors smaller than 0.1µF; soft-start capacitors of 0.1µF and above should present a soft-start ramp void of this plateau. At time T3, 3ms (typically) past the 5VSB POR (T1), the memory output voltage selection is latched in and the charging of the softstart capacitor resumes, using the 10µA current source. At this point, the error amplifiers’ reference inputs are starting their transitions, causing the output voltages to ramp up proportionally. The ramping continues until time T4 when all the voltages reach the set value. At time T5, when the softstart capacitor value reaches approximately 2.8V, the undervoltage monitoring circuits are activated and the soft-start capacitor is quickly discharged down to the value attained at time T2 (approximately 1.25V). 3V3DL 5VDLSB 5VSB (1V/DIV) 5VDL SOFT-START (1V/DIV) FIGURE 7. 3VDUAL AND 5VDUAL TIMING DIAGRAM FOR EN3VDL = 0, EN5VDL = 0 UV DETECT ENABLE (LOGIC LEVEL) 0V 5VSB VOUT3 (5VDUAL) S3 OUTPUT VOLTAGES (1V/DIV) S5 VOUT1 (3.3VDUAL) 12V VOUT2 (2.5VMEM) INTERNAL VSEN2 DEVICE DRV2 0V VSEN2 T0 T1 T2 T3 FIGURE 8. 2.5/3.3VMEM TIMING DIAGRAM 8 T4 T5 TIME FIGURE 9. SOFT-START INTERVAL IN A SLEEP STATE (ALL OUTPUTS ENABLED) FN4749.6 December 30, 2004 HIP6501A Soft-Start into Active States (S0, S1) If both S3 and S5 are logic high at the time the 5VSB is applied, the HIP6501A will assume an active state and keep off the controlled external transistors until about 50ms after the ATX’s 12V output (sensed at the 12V pin) exceeds the set threshold (typically 10.8V). This timeout feature is necessary in order to ensure the main ATX outputs are stabilized. The timeout also assures smooth transitions from sleep into active when sleep states are being supported. During sleep to active state transitions from conditions where the outputs are initially 0V (such as S4/S5 to S0 transition with EN3VDL = 1 and EN5VDL = 0, or simple power-up sequence directly into active state), the 3VDUAL and 5VDUAL outputs go through a quasi soft-start by being pulled high through the body diodes of the N-channel MOSFETs connected between these outputs and the 3.3V and 5V ATX outputs, respectively. Figure 10 shows this startup scenario. +12VIN DLA PIN (2V/DIV) INPUT VOLTAGES (2V/DIV) +5VIN +5VSB +3.3VIN SOFT-START (1V/DIV) 0V OUTPUT VOLTAGES (1V/DIV) VOUT3 (5VDUAL) VOUT1 (3.3VDUAL) VOUT2 (2.5VMEM) 0V T0 T1 T2 T3 T4 TIME FIGURE 10. SOFT-START INTERVAL IN AN ACTIVE STATE 5VSB is already present when the main ATX outputs are turned on at time T0. Similarly, the soft-start capacitor has already been charged up to 1.25V and the clamp is active, awaiting for the 12V POR timer to expire. As a result of 3.3VIN and 5VIN ramping up, the 3.3VDUAL and 5VDUAL output capacitors charge up through the body diodes of Q3 and Q5, respectively (see Figure 3). At time T1, the 12V ATX output exceeds the HIP6501A’s 12V under-voltage threshold, and the internal 50ms (typical) timer is initiated. At T2 the time-out initiates a soft-start, and the memory output is ramped-up, reaching regulation limits at time T3. 9 Simultaneous with the memory voltage ramp-up, the DLA pin is pulled high (to 12V), turning on Q3 and Q5, and bringing the 3.3VDUAL and 5VDUAL outputs in regulation at time T2. At time T4, when the soft-start voltage reaches approximately 2.8V, the under-voltage monitoring circuits are enabled and the soft-start capacitor is quickly discharged to approximately 2.45V. Requests to go into a sleep state during an active state softstart ramp-up result in a chip reset, followed by a new softstart sequence into the desired state. Fault Protection All the outputs are monitored against under-voltage events. A severe over-current caused by a failed load on any of the outputs, would, in turn, cause that specific output to suddenly drop. If any of the output voltages drop below 69% of their set value, such event is reported by having the FAULT/MSEL pin pulled to 5V. Additionally, the 2.5/3.3V memory regulator is internally current limited while in a sleep state. Exceeding the maximum current rating of this output in a sleep state can lead to output voltage drooping. If excessive, this droop can ultimately trip the under-voltage detector and send a FAULT signal to the computer system. However, a FAULT condition will only set off the FAULT flag, and it will not shut off or latch off any part of the circuit. If shutdown or latch off of the circuit is desired, this can be achieved by externally pulling or latching the SS pin low. Pulling the SS pin low will also force the FAULT pin to go low. Under-voltage sensing is disabled on all disabled outputs and during soft-start ramp-up intervals. SS voltage reaching the 2.8V threshold signals activation of the under-voltage monitor. Another condition that could set off the FAULT flag is chip over-temperature. If the HIP6501A reaches an internal temperature of 125oC (minimum), the FAULT flag is set (FAULT/MSEL pulled high), but the chip continues to operate until the temperature reaches 150oC (typical), when unconditional latched shutdown of all outputs takes place. The thermal latch can be reset only by cycling the 5VSB off, and then on. Output Voltages The output voltages are internally set and do not require any external components. Selection of the memory voltage is done by means of an external resistor connected between the FAULT/MSEL pin and ground. An internal 40µA (typical) current source creates a voltage drop across this resistor. During every 5VSB trip above POR level, this voltage is compared with an internal reference (200mV typically). Based on this comparison, the output voltage is set at either 2.5V (RSEL = 1kΩ), or 3.3V (RSEL = 10kΩ). It is very important that no capacitor is connected to the FAULT/MSEL pin; the presence of a capacitive element at this pin can lead to false memory voltage selection. See Figure 11 for details. FN4749.6 December 30, 2004 HIP6501A undergoes a new soft-start cycle and resumes normal operation in accordance to the ATX supply and control pins status. FAULT/MSEL Layout Considerations MEM VOLTAGE SELECT COMP RSEL + 40µA 1kΩ 2.5V 10kΩ 3.3V - 0.2V +12VIN +5VSB FIGURE 11. 2.5/3.3VMEM OUTPUT VOLTAGE SELECTION CIRCUITRY DETAILS 12V SS Application Guidelines CIN C5VSB C12V 5VSB Q4 5VDLSB CSS VOUT3 5VDL Soft-Start Interval The built-in soft-start circuitry allows tight control of the slewup speed of the output voltages controlled by the HIP6501A, thus enabling power-ups free of supply drop-off events. Since the outputs are ramped up in a linear fashion, the current dedicated to charging the output capacitors can be calculated with the following formula: Q2 3V3DLSB CHF1 VOUT1 CBULK3 CHF3 HIP6501A 3V3DL LOAD The 5VSB output of a typical ATX supply is capable of 725mA. During power-up in a sleep state, it needs to provide sufficient current to charge up all the output capacitors and simultaneously provide some amount of current to the output loads. Drawing excessive amounts of current from the 5VSB output of the ATX can lead to voltage collapse and induce a pattern of consecutive restarts with unknown effects on the system’s behavior or health. LOAD VMEM Q5 DLA +5VIN CBULK1 VOUT2 CHF2 VSEN2 Q3 GND DRV2 Q1 CBULK2 LOAD RSEL + The typical application employing a HIP6501A is a fairly straight-forward implementation. Similar to any other linear regulators, attention has to be paid to a few potentially sensitive small signal components, such as those connected to high-impedance nodes or those supplying critical by-pass currents. +3.3VIN KEY ISLAND ON POWER PLANE LAYER I SS I COUT = -------------------------------- × Σ ( C OUT × V OUT ) , where C SS × V BG ISS - soft-start current (typically 10µA) CSS - soft-start capacitor VBG - bandgap voltage (typically 1.26V) Σ(COUT xVOUT) - sum of the products between the capacitance and the voltage of an output. Due to the various system timing events, it is recommended that the soft-start interval not be set to exceed 30ms. Additionally, the recommended soft-start capacitor range spans from 5nF up to 0.22µF (0.1µF recommended). Shutdown In case of a FAULT condition that might endanger the computer system, or at any other time, the HIP6501A can be shut down by pulling the SS pin below the specified shutdown level (typically 0.8V) with an open drain or open collector device capable of sinking a minimum of 2mA. Pulling the SS pin low effectively shuts down all the pass elements. Upon release of the SS pin, the HIP6501A 10 ISLAND ON CIRCUIT/POWER PLANE LAYER VIA CONNECTION TO GROUND PLANE FIGURE 12. PRINTED CIRCUIT BOARD ISLANDS The power components (pass transistors) and the controller IC should be placed first. The controller should be placed in a central position on the motherboard, closer to the memory load if possible. Ensure the VSEN2 connection is properly sized to carry 200mA without significant resistive losses. The pass transistors should be placed on pads capable of heatsinking, matching the device’s power dissipation. Where applicable, multiple via connections to a large internal plane can significantly lower localized device temperature rise. Placement of the decoupling and bulk capacitors should follow a placement reflecting their purpose. As such, the high-frequency decoupling capacitors (CHF) should be placed as close as possible to the load they are decoupling; the ones decoupling the controller (C12V, C5VSB) close to the controller pins, the ones decoupling the load close to the load connector or the load itself (if embedded). The bulk FN4749.6 December 30, 2004 HIP6501A capacitance (aluminum electrolytics or tantalum capacitors) placement is not as critical as the high-frequency capacitor placement, but having these capacitors close to the load they serve is preferable. Since the output voltage drop is heavily dependent on the ESR (equivalent series resistance) of the output capacitor bank, the capacitors should be chosen to maintain the output voltage above the lowest allowable regulation level. The only critical small signal component is the soft-start capacitor, CSS. Locate this component close to SS pin of the control IC and connect to ground through a via placed close to the capacitor’s ground pad. Minimize any leakage current paths from SS node, since the internal current source is only 10µA. Input Capacitors Selection A multi-layer printed circuit board is recommended. Figure 12 shows the connections of most of the components in the converter. Note that the individual capacitors each could represent numerous physical capacitors. Dedicate one solid layer for a ground plane and make all critical component ground connections through vias placed as close to the component as possible. Dedicate another solid layer as a power plane and break this plane into smaller islands of common voltage levels. Ideally, the power plane should support both the input power and output power nodes. Use copper filled polygons on the top and bottom circuit layers to create power islands connecting the filtering components (output capacitors) and the loads. Use the remaining printed circuit layers for small signal wiring. Component Selection Guidelines Output Capacitors Selection The output capacitors for all outputs should be selected to allow the output voltage to meet the dynamic regulation requirements of active state operation (S0, S1). The load transient for the various microprocessor system’s components may require high quality capacitors to supply the high slew rate (di/dt) current demands. Thus, it is recommended that capacitors COUT1 and COUT2 should be selected for transient load regulation. Also, during the transition between active and sleep states, there is a short interval of time during which none of the power pass elements are conducting - during this time the output capacitors have to supply all the output current. The output voltage drop during this brief period of time can be approximated with the following formula: tt ∆VOUT = I OUT × ESR OUT + ------------------ , where C OUT ∆VOUT - output voltage drop ESROUT - output capacitor bank ESR The input capacitors for an HIP6501A application must have sufficiently low ESR so that the input voltage does not dip excessively when energy is transferred to the output capacitors. If the ATX supply does not meet the specifications, certain imbalances between the ATX’s outputs and the HIP6501A’s regulation levels could result in a brisk transfer of energy from the input capacitors to the supplied outputs. When transiting from active to sleep states, this phenomena could result in the 5VSB voltage dropping below the POR level (typically 4.3V) and temporarily disabling the HIP6501A. The solution to this potential problem is to use larger input capacitors (on 5VSB) with a lower total combined ESR. Transistor Selection/Considerations The HIP6501A typically requires one P-Channel and two N-Channel power MOSFETs and two bipolar NPN transistors. One general requirement for selection of transistors for all the linear regulators/switching elements is package selection for efficient removal of heat. The power dissipated in a linear regulator/switching element is: P LINEAR = I O × ( V IN – V OUT ) Select a package and heatsink that maintains the junction temperature below the rating with the maximum expected ambient temperature. Q1 The active element on the 2.5V/3.3VMEM output has different requirements for each of the two voltage settings. In 2.5V systems utilizing RDRAM (or voltage-compatible) memory, Q1 must be a bipolar NPN capable of conducting the maximum required output current and it must have a minimum current gain (hfe) of 100-150 at this current and 0.7V VCE. In such systems, the 2.5V output is regulated from the ATX 3.3V output while in an active state. In 3.3V systems (SDRAM or compatible) Q1 must be an N-Channel MOSFET, since the MOSFET serves as a switch during active states (S0, S1). The main criteria for the selection of this transistor is output voltage budgeting. The maximum rDS(ON) allowed at highest junction temperature can be expressed with the following equation: IOUT - output current during transition V IN MIN – V OUTMIN r DS ( ON ) MAX = ------------------------------------------------------------ , where I OUT MAX COUT - output capacitor bank capacitance VIN MIN - minimum input voltage tt - active-to-sleep or sleep-to-active transition time (10µs typical) VOUT MIN - minimum output voltage allowed IOUT MAX - maximum output current The gate bias available for this MOSFET is approximately 8V. 11 FN4749.6 December 30, 2004 HIP6501A Q4 Q3, Q5 If a P-Channel MOSFET is used to switch the 5VSB output of the ATX supply into the 5VDUAL output during S3 and S4/S5 states (as dictated by EN5VDL status), then, similar to the situation where Q1 is a MOSFET, the selection criteria of this device is also proper voltage budgeting. The maximum rDS(ON), however, has to be achieved with only 4.5V of VGS, so a logic level MOSFET needs to be selected. If a PNP device is chosen to perform this function, it has to have a low saturation voltage while providing the maximum sleep-state current and have a current gain sufficiently high to be saturated using the minimum drive current (typically 20mA; 4mA during soft-start). The two N-Channel MOSFETs are used to switch the 3.3V and 5V inputs provided by the ATX supply into the 3.3VDUAL and 5VDUAL outputs, respectively, while in active (S0, S1) states. Similar rDS(ON) criteria apply in these cases as well, unlike the PMOS, however, these NMOS transistors get the benefit of an increased VGS drive (approximately 8V and 7V, respectively). 12 Q2 The NPN transistor used as sleep-state pass element on the 3.3VDUAL output must have a minimum current gain of 100 at VCE = 1.5V, and ICE = 500mA throughout the in-circuit operating temperature range. FN4749.6 December 30, 2004 HIP6501A HIP6501A Application Circuit employing SDRAM memory, replace R1 with 10kΩ and Q1 with an HUF76113SK8. Q4 can also be a PNP, such as an MMBT2907AL. For detailed information on the circuit, including a Bill-of-Materials and circuit board description, see Application Note AN9846. Figure 13 shows an application circuit of an ACPI-compliant power management system for a microprocessor computer system. The power supply provides the PCI 3.3VDUAL voltage (VOUT1), the RDRAM 2.5VMEM memory voltage (VOUT2), and the 5VDUAL voltage (VOUT3) from +3.3V, +5V, +5VSB, and +12VDC ATX supply outputs. For systems See Intersil’s web site www.intersil.com for the latest information. +5VIN +12VIN +3.3VIN + +5VSB + C2 1µF C4 1µF 12V C3 220µF C5 1µF 5VSB 3V3DLSB Q2 2SD1802 VOUT1 C1 10µF DRV2 Q1 2SD1802 VSEN2 Q3 1/2 HUF76113DK8 VOUT2 3V3DL 3.3VDUAL C6 1µF + C8,9 2x150µF C7 220µF FAULT/MSEL U1 HIP6501A + 2.5VMEM C10 1µF Q4 FDV304P 5VDLSB R1 1K DLA Q5 1/2 HUF76113DK8 S3 S3 S5 VOUT3 5VDL S5 EN5VDL + EN5VDL EN3VDL C11 150µF C12 1µF 5VDUAL EN3VDL SS SHUTDOWN (FROM OPEN-DRAIN N-MOS) C13 0.1µF GND FIGURE 13. TYPICAL HIP6501A APPLICATION CIRCUIT 13 FN4749.6 December 30, 2004 HIP6501A Small Outline Plastic Packages (SOIC) M16.15 (JEDEC MS-012-AC ISSUE C) 16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE N INCHES INDEX AREA H 0.25(0.010) M B M SYMBOL E -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -C- e B 0.25(0.010) M C 0.10(0.004) C A M B S MILLIMETERS MAX MIN MAX NOTES A 0.053 0.069 1.35 1.75 - A1 0.004 0.010 0.10 0.25 - B 0.014 0.019 0.35 0.49 9 C 0.007 0.010 0.19 0.25 - D 0.386 0.394 9.80 10.00 3 E 0.150 0.157 3.80 4.00 4 e µα A1 MIN 0.050 BSC 1.27 BSC - H 0.228 0.244 5.80 6.20 - h 0.010 0.020 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 8o 0o N α 16 0o 16 7 8o Rev. 1 02/02 NOTES: 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 14 FN4749.6 December 30, 2004