Signal processing circuit for 1-D PSD C3683-02 Circuit board for easier 1-D PSD operation The C3683-02 is a DC signal processing circuit for one-dimensional PSD. It is suitable for displacement measurements using DC light. Features Applications No complicated adjustments required Position measurement of a light spot can be made simply by mounting 1-D PSD. Output voltage directly representing the position data The position (mm) of a light spot from the PSD (S3931, S3932) center is obtained as an output voltage (V). Displacement measurements using DC light Various studies using 1-D PSD Performance evaluation of 1-D PSD Accurate position sensing Position data of a light spot is independent of incident light intensity. Three sensitivity ranges Compact design Head amp, signal addition/subtraction circuits, and analog divider circuit are mounted on a compact PC board. Absolute maximum ratings (Ta=25 °C unless otherwise noted) Parameter Supply voltage Operating temperature*1 Storage temperature*1 Input voltage Output short-circuit time Symbol Vcc max Topr Tstg VIN max - Value ±18 0 to +50 -10 to +60 Vcc max Continuous Unit V °C °C V s *1: No dew condensation When there is a temperature difference between a product and the surrounding area in high humidity environment, dew condensation may occur on the product surface. Dew condensation on the product may cause deterioration in characteristics and reliability. Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the product within the absolute maximum ratings. www.hamamatsu.com 1 Signal processing circuit for 1-D PSD C3683-02 Specifications (Ta=25 °C, Vcc=±15 V) Parameter Symbol Head amp conversion impedance Rf *2 Head amp feedback capacitance Cf *2 Input signal current IIN *3 Tr VOH VOL Vn Vos Tr VOH VOL Vn Vos Tr VOH VOL Vn Vos Tr *4 Head amp output (V1, V2) Sum signal output (VA) Subtracted signal output (VB) Analog divider output (Vo) Rise time High Output voltage Low Output noise voltage Output offset voltage Rise time High Output voltage Low Output noise voltage Output offset voltage Rise time High Output voltage Low Output noise voltage Output offset voltage Rise time Maximum output amplitude voltage Output noise voltage Output offset voltage Vo Vn Vos PSD reverse bias voltage VR Supply voltage Current consumption Vcc Icc Condition H range M range L range H range M range L range H range M range L range *5 *5 *4 *5 *5 *4 *5 *5 *4 Factory setup prior to shipping*6 *5 *5 Factory setup prior to shipping*7 *8 *5 Min. 1 × 10-6 1 × 10-5 1 × 10-4 -1 +13.5 -5 +13.5 -5 - Typ. 1 × 106 1 × 105 1 × 104 10 100 1000 22 0 -13.8 2 22 +13.8 0 2 22 +13.8 -13.8 2 22 Max. 1 × 10-5 1 × 10-4 1 × 10-3 30 -13.5 +1 30 +5 30 -13.5 +5 30 Unit ±5.8 ±6 ±6.2 V -60 5 - +60 mVp-p mV +4.9 +5 +5.1 V ±14.5 - ±15 ±8 ±15.5 - V mA V/A pF A μs V mVp-p mV μs V mVp-p mV μs V mVp-p mV μs Factory setup prior to shipping is M range. The range can be switched with the jumper on the board. Photocurrent with PSD installed. PSD does not operate correctly if the input signal current is outside the specified range. Output response time 10 to 90% With no PSD installed. Current signal that substitutes for PSD photocurrent (L range: X1=X2=400 μA, M range: X1=X2=40 μA, H range: X1=X2=4 μA) is input. When maximum output amplitude voltage Vo=±6 V is set. *6: Factory setup prior to shipping is ±6 V. Maximum output amplitude can be adjusted in a range of ±2 to ±10 V with a variable resistor on the board according to the PSD type to be used. *7: Factory setup prior to shipping is +5 V. The voltage can be adjusted in the range of 0 to +14 V with a variable resistor on the board. *8: Switching power supplies are not supported. Use a series power supply (with 3 mVp-p or less ripple voltage). *2: *3: *4: *5: 2 Signal processing circuit for 1-D PSD C3683-02 Combination with a PSD A PSD is installed (soldered) on the signal processing circuit. Note: PSDs are sold separately. Photosensitive area size (mm) 6×1 12 × 1 37 × 1 24 × 0.7 2×1 3×1 3×1 3.5 × 1 3.5 × 1 4.2 × 1 6×1 Type no. S3931 S3932 S3270 S8543 S4581-04 S4583-04 S8673 S4584 series S3274-05 S7105 series S5629 series Package (mm) Ceramic (9.2 × 4.8) Ceramic (15.2 × 4.8) Ceramic (55 × 5) Ceramic (36.7 × 4) Plastic Plastic Plastic Plastic Plastic Plastic Plastic Installation on board External attachment*9 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes *9: Wiring using shielded wires or AWG#26 or equivalent twisted pair wires (no longer than 30 cm) is recommended. PSD and output voltage With the D-sub connector on top, the output corresponding to the horizontal position (converted output voltage of the X position) is output from D-sub connector terminal No. 2 (Vo). C3683-02 Output Vo (V) D-sub connector L/2 PSD installation area S3931/S3932 L/4 -L/2 0 Incident light (light spot) X -L/4 L/2 Light spot position X (mm) S3270 -L/2 -L/2 KACCC0649EA +L/2 L: PSD photosensitive area length (mm) KACCC0651EA Parameter Photosensitive area length Output voltage amplitude Symbol L Vo(X) S3931 6 ±3 One-dimensional PSD S3932 12 ±6 S3270 37 ±9.25 Unit mm V 3 Signal processing circuit for 1-D PSD C3683-02 Connection example Measured light (DC light) One-dimensional PSD (sold separately) +15 V GND -15 V Dual power supply (±15 V, 0.1 A or more) Be sure to use a dual power supply. Switching power supplies are not supported. Use a series power supply (with 3 mVp-p or less ripple voltage). Vo GND C3683-02 Voltmeter, oscilloscope, etc. KACCC0653EB Dimensional outline (unit: mm) Through holes for externally connected PSD (5 ×) 1 (2.54 pitch) PSD installation position 56 50 3 1.6 MADE IN JAPAN S3932 S3931 60 S3270 66 8.5 C3683-02 3 1234 5 (4 ×) C1 (20) (4 ×) 3.2 D-sub connector (Hirose Electric: RDED-9P) 15.5 max. Tolerance: ±0.2 KACCA0307EA 4 Signal processing circuit for 1-D PSD C3683-02 Pin connections D-sub connector Pin no. 1 2 3 4 5 6 7 8 9 Name VR Vo -V +V G VB V2 V1 VA Content PSD reverse bias voltage output Analog divider output (position signal output) -15 V +15 V GND Differential signal output Head amp output X2 Head amp output X1 Sum signal output (incident light level monitor output) Through holes for externally connected PSD Pin no. Name Content 1 X2 Connection to PSD anode terminal “X2” 2 G GND (for signal cable shield) PSD reverse bias voltage output: 3 VR Connection to PSD cathode terminal 4 G GND (for signal cable shield) 5 X1 Connection to PSD anode terminal “X1” Accessories ∙ Instruction manual ∙ Connector HDEB-9S (Hirose Electric: for connections to power supply and output readout device) Related information www.hamamatsu.com/sp/ssd/doc_en.html Precautions ∙ Disclaimer Information described in this material is current as of June, 2016. Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always contact us for the delivery specification sheet to check the latest specifications. The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use. Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39) 02-93581733, Fax: (39) 02-93581741 China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866 Cat. No. KPSD1004E05 Jun. 2016 DN 5