an9827

HI5728EVAL1 User’s Manual
TM
Application Note
February 2000
AN9827.2
Description
Features
The HI5728EVAL1 evaluation board provides a quick and
easy method for evaluating the HI5728, 125MSPS Dual High
Speed DAC. Each converter outputs a current into a load
resistor to form a voltage which can be measured by using
the included SMA connectors. The amount of current out of
the DAC is determined by an external resistor and either an
internal or external reference voltage. The evaluation board
also includes a VME digital interface that is compatible with
the HSP-EVAL board, so DDS (Direct Digital Synthesis) can
be performed with minimal setup time. A transformer is
included to take advantage of differential signal drive.
• HI5728, 125MSPS CMOS DAC
Ordering Information
• General DAC Performance Evaluation
PART
NUMBER
TEMP.
RANGE (oC)
PACKAGE
HI5728EVAL1
25
Evaluation Platform
• Simple and Easy to Use
• Standard VME/DSP Interface, HSP-EVAL Compatible
• SMA Outputs with Transformer Option
• Easily Selectable Internal or External Reference
Applications
• I and Q Signal Generation
• Modulated Carrier Generation
• Amplitude Modulation Via External Reference
CLOCK
SPEED
125MHz
Functional Block Diagram
P1
RSET POT
DVDD
R68
AVDD
I-CHANNEL 10 BITS
VME
64 or 96-PIN
CONNECTOR
U1
IOUTA
IOUTB
Q-CHANNEL 10 BITS
T1
XFMR
IOUT
SMA5
XFMR
QOUT
SMA6
HI5728
CLOCK
ICLK
SMA8
QCLK
SMA9
DAC
ICLK
QCLK
REF SELECT
QOUTB
QOUTA
T2
J2
AVDD
J1
SLEEP
EXTERNAL
REFERENCE
(OPTIONAL)
SMA7
3-1
J3
1-888-INTERSIL or 321-724-7143
|
Intersil and Design is a trademark of Intersil Corporation.
|
Copyright
© Intersil Corporation 2000
Application Note 9827
Functional Description
Overview
The evaluation board is configured to be interfaced using a
VME connector. The data input lines are tied together using
small, zero ohm resistors on the back side of the board (QD0
is tied to ID0, continued with QD9 connected to ID9; see the
schematic, R54, 58-60, 62-67). This is done so that the data
can be driven into both of the channels without having to
generate two patterns. This aids in simplifying the evaluation
of the part. If the user has the ability to generate dual
patterns during the evaluation process, these resistors must
be removed. Both series and parallel termination resistor
footprints are provided, so that the user may customize the
termination method. An internal voltage reference is
available, as well as a variable resistor for customizing the
output current. RF transformers are populated for taking
advantage of the complimentary current outputs. They can
be disabled from the circuit by removing several zero ohm
resistors if a simple load resistor output is desired.
Voltage Reference
The HI5728 has an internal voltage reference (1.16V typical)
with a ±60ppm/oC drift coefficient over the full temperature
range of the converter. The REFLO pin (15) selects the
reference. Access to pin 15 is provided through the center
pin of Jumper J2. To enable the internal reference, it is
necessary that the jumper be placed such that pin 15 is
grounded (J2 is labeled on the board as INT and EXT, for
internal and external). The REFIO pin (23) provides access
to the internal voltage reference, or can be overdriven if the
user wishes to use an external source for the reference.
Notice that a 0.1µF capacitor is placed as close as possible
to the REFIO pin. This capacitor is necessary for ensuring a
quiet reference voltage.
If the user wishes to use an external reference voltage,
jumper J3 must be in place and an external voltage
reference provided via SMA7, labeled ‘EXT REF’. Jumper J2
must be changed so that pin 16 is tied high (the supply
voltage, which is the EXT position of J2) when using an
external reference. The recommended limits of the external
reference are between 15mV and 1.2V, which provides over
36dB of multiplying capability. Performance of the converter
can be expected to decline as the reference voltage is
reduced due to the reduction in LSB current size.
If the user wishes to amplitude modulate the reference, the
REFIO pin can be overdriven with a waveform. The input
multiplying bandwidth of the REFIO input is approximately
1.4MHz. It is necessary that the multiplying signal be DC
offset so that the minimum and maximum peaks of the signal
are above 0V and less than 1.2V. The output current of each
converter is a function of the voltage reference used and the
value of RSET (R68 or R35 on the schematic). R68 is a
potentiometer that can be used to vary the RSET if the user
wishes to explore various output current levels. The board is
3-2
shipped with R68 set to ~2kΩ. The converter’s performance
sometimes improves with reduced output current. R35 is
provided if the user wishes to set the output current using a
set value. See the ‘Outputs’ section for more information on
setting the output current.
The footprints for SMA10 and SMA11 were provided on the
evaluation board so that separate multiplying signals could
be attached, along with alternate op amps, to overdrive the
internal reference op amps via ICOMP1 and QCOMP1 to
increase the multiplying bandwidth of the references for
DACs I and Q independently. SMA11 was placed next to
prototyping area so that an external op amp could be placed
between E11 and E7, which provides access to QCOMP1
via a zero ohm resistor, R69. It was intended that this
capability also exist between E10 and E6 for access to
ICOMP1 so that it could be driven independently if desired,
but E6 was mistakenly grounded. So the ability to overdrive
ICOMP1 and QCOMP1 exists on this board, but it must be
done with a single op amp and signal simultaneously via
SMA11, E7, and E11. ICOMP1 cannot be driven
independently using SMA10, E6, and E10. R56 should never
be populated. See the functional block diagram of the
HI5728 in the data sheet and the evaluation board schematic
located in this document for more information.
Outputs
The output current of the device is set by choosing RSET
and VFSADJ such that the resultant of the following equation
is less than 20mA:
IOUT = 32 x VFSADJ /RSET.
For example, using the internal VFSADJ of 1.16V nominal
and an RSET (R35 on the schematic) value of 1.86kΩ results
in an IOUT of approximately 20mA (maximum allowed).
Choose the output loading so that the ‘Output Voltage
Compliance Range’ is not violated (-0.3 to 1.25V). If an
external VREF is chosen, it should not exceed +1.2V.
The output can be configured to drive a load resistor, a
transformer, an operational amplifier, or any other type of
output configuration so long as the output voltage
compliance range and the maximum output current is not
violated.
Load Resistor Output
If the user wishes to use only a load resistor and no
transformer, they should remove the zero ohm resistors that
connect the outputs to the transformers. These resistors are
R51, R57, R70, and R72. See the schematic for details. The
output voltage developed is simply a function of the output
current multiplied by the output load. Care should be taken
to ensure that this voltage does not violate the output
compliance range of -300mV to 1.25V.
Application Note 9827
Differential Output
Clock Inputs
The board is also configured with the following transformer
output which will result in an output voltage amplitude that is
twice that of IOUT x Req, where Req is the equivalent
resistive loading seen by the current outputs (~12.5Ω =
(50//50//25). The transformer used in this circuit is a MiniCircuits 1:1 RF Transformer, T1-1T. The impedance looking
back into the transformer from the 50Ω spectrum analyzer is
50Ω (100Ω/2), so proper termination is achieved and
reflections are minimized. The transformer benefits the user
by reducing the even-order harmonics and therefore
increasing the SFDR (Spurious Free Dynamic Range). It can
be taken out of the output by removing the zero ohm
jumpers, R51, 57, 70, and 72. With the transformers
removed, SMAs 1-4 should be used to measure the output
voltages across the included 50Ω loads.
The elaborate nature of the clock input circuit (see the
schematic) achieves versatility. It provides the means to drive
both channels from a single clock via the VME connector, or to
drive each with separate clocks via SMAs 8 and 9. Notice that
the 0Ω resistors (R28, 29, 50 and 53) are used as jumpers to
enable the different clock sources without degrading signal
integrity, or they can be replaced by nominal value resistors if
series input termination(s) are desired on the clock(s).
HI5728
VOUT = (2 x IOUT x REQ)V
PIN 17 (20)
50Ω
IOUTB (QOUTB)
100Ω
PIN 16 (21)
50Ω
IOUTA (QOUTA)
50Ω
FIGURE 1.
Sleep
Input Termination
For clock rates below 50MSPS, the method of input
termination on the data and clock lines could be open, 50Ω,
or nominal series, depending on the current drive available
from the digital source. The performance of the converter
should not vary greatly with the termination method for these
update rates. For clock rates above 50MSPS, it may be
necessary that 50Ω termination resistors be used on this
board to achieve optimum spectral purity. If the digital
pattern source cannot drive this load, it is recommended that
200Ω series resistors be used at high clock rates. The board
is shipped with 200Ω series resistors on the data and clock
lines. Notice that the PCB footprints are available on the
board for either termination technique. For high clock rates,
adjustment of the timing between the clock and the data may
be necessary for optimum performance. When implementing
the HI5728 onto a board that contains the digital data/clock
source in close proximity to the DAC, it is unlikely that any
termination resistors will be required.
The converter can be put into ‘sleep’ mode by connecting pin
8 to either of the converter’s supply voltages. For normal
operation, it is recommended that pin 8 be tied to ground.
However, the sleep pin does have an active pulldown
current, so the pin can be left disconnected. On the
evaluation board, jumper J1 is provided for controlling the
sleep pin. Remove the jumper from J1 for normal operation
and replace it for sleep mode.
Note that the board is also shipped with both input channels
tied together via 0Ω, 402 package resistors on the bottom of
the board. This is done so that both channels can be
evaluated from a single pattern generator. If 50Ω termination
is used while the channels are tied together, it should be
obvious that they are only needed on one channel, not both;
else you will be driving 25Ω.
Power Supply(ies) and Ground(s)
Getting Started
The user can operate from either a single supply or dual
supplies. The DAC is designed to function with the digital
and analog voltages at the same value or at different values.
The DAC can be driven with a 3 or 3.3V digital supply and a
5V analog supply. In compliance with the absolute maximum
ratings for the DAC listed in the datasheet, the digital input
voltages should not be more than DVDD + 0.3V. A single
power supply wire can be attached to either DVDD1 or
AVDD1, and then the DVDD1 and AVDD1 holes jumpered
together on the board using regular wire if a single supply is
desired. The board uses dual ground planes connected at a
single point near the converter (this is the recommended
configuration). For dual supply mode, connect a power
supply wire to both AVDD1 and DVDD1 and ground wires to
DGND1 and AGND1 independently.
3-3
A summary of the external supplies, equipment, and signal
sources needed to operate the board is given below:
1. +3V to +5V power supply(ies) for HI5728.
2. Data Generator capable of generating 10-bit patterns.
The HSP-EVAL with the HSP45116 NCOM daughter
board is an option (see ‘Learning Your Way Around’).
3. Clock source (usually part of the Data Generator).
4. Spectrum Analyzer or Oscilloscope for viewing the output
of the converter.
Attach a +3V to +5V power supply to the evaluation board
connections labeled DVDD1 and AVDD1. Connect the 10 input
bits from the data generator to the evaluation board, preferably
by using a male, 64 or 96-pin VME (Versa Module Eurocard)
connector that mates with the eval board. See the schematic for
the correct pin connections. The middle row of the VME is not
used, which is why either a 64 or 96-pin connector will work.
Application Note 9827
Connect the clock source to the eval board, also preferably
through the VME connector (or using the clock SMAs; see the
‘Clock Inputs’ section for more information). Failure to make
clean and short connections to the data input lines and clock
source will result in a decrease in spectral performance.
Using a coaxial cable with the proper SMA connector, attach
the output of one of the transformers, IOUT or QOUT, to the
measurement equipment that will be evaluating the
converter’s performance. Make sure that the jumpers are in
their proper placement. Consult the ‘Voltage Reference’
section and the ‘Sleep’ section of this document for a
definition of the jumpers’ functionality.
Learning Your Way Around
Direct Digital Synthesis
To ensure that everything on the board is configured
properly and functional, it is suggested that the following
DDS setup be implemented. The board test requires:
1. HI5728 Evaluation Board.
2. Spectrum Analyzer.
3. HSP-EVAL Board with the HSP45116 NCOM Daughter
Board Attached and included software, NCOMCTRL (or
a Data/Pattern Generator).
4. Personal Computer (IBM compatible) with a Parallel Port.
5. 50Ω SMA Cable.
6. Two +5V power supplies. One for the DAC Eval Board and
one for the HSP Eval Board.
Note: If the HSP-EVAL Board is to be used, it is highly
recommended that the user obtain the User’s Manual, the
data sheet for the HSP45116 NCOM, and the User’s Manual
for the HSP45116-DB. This platform is capable of testing the
converter up to 25MSPS, which is the speed of the HSPEVAL’s on-board clock. The user can choose to substitute
this clock with a slower one, but the DSP chip and DSP Eval
Board are only designed to work at a maximum of 25MHz (a
52MHz version of this DSP chip does exist but not in this
evaluation platform; see the HSP45116A). For testing of the
HI5728 at higher speeds, it is recommended that the user
3-4
obtain a high speed data generator capable of generating 10
bit patterns at the clock speed needed. The HSP45116
NCOM generates two, 16-bit channels of data.
HI5728EVAL1 is designed so that both of its input channels
mate with both of the DSP’s output channels. The zero ohm
resistors that connect the I and Q channels together on the
DAC eval board must be removed before using the
HSP45116 evaluation board. Also, the DSP Eval Board
cannot drive 50Ω.
HSP-EVAL Setup for DDS
Attach the HSP-EVAL and the HSP45116 Daughter Board
together; see figure 2. Consult their respective user manuals
for details. Connect the HI5728EVAL1 board to the P2
connector of the HSP-EVAL board. Then connect these to
an IBM compatible PC via the parallel port. Provide power to
both boards. To run the software (NCOMCTRL) that
accompanied the HSP evaluation kit, place the diskette into
the 3.5” drive of the PC and type:
(drive letter):\NCOMCTRL,
which will run the HSP45116 Control Panel software. Set the
control panel’s selections to the following and check one of
the outputs of the DACs at either IOUT or QOUT using the
spectrum analyzer for a frequency equal to 1.63MHz.
The clock select of the control panel should be set to ‘Osc.
CLK’. The control signals should be as follows:
0 ENPHREG
0 CLROFR
1 LOAD
0 BINFMT
1 PMSEL
The amplitude of the real output (RIN0-15) should be
8000HEX for full scale output. The center frequency register
can be set to 10ABCDEFHEX for a 1.63MHz tone. The
Offset Frequency, Phase Offset, and Time Accumulator
Registers should all be set to zeros. The spurious free
dynamic range that can be expected is typically 70dBc with
this setup operating at this frequency.
Application Note 9827
HSP-EVAL/HSP45116
NCOM EVALUATION BOARD
OR A DATA GENERATOR
CLOCK
CIRCUIT
HI5728EVAL1
DAC MODULE
HI5728
HSP-EVAL/HSP45116DB
NUMERICALLY
CONTROLLED
OSCILLATOR
EVAL KIT
10 BITS
I Channel
10 BITS
Q Channel
PC INTERFACE
+5V
POWER
SUPPLY
50Ω
SMA
CABLE
+5V
POWER
SUPPLY
SOFTWARE
INCLUDED
WITH HSP-EVAL
SPECTRUM ANALYZER
PERSONAL COMPUTER
FIGURE 2. INTERSIL HI5728/DDS EVALUATION SYSTEM SETUP BLOCK DIAGRAM
Appendix A Description of Architecture
The segmented current source architecture has the ability to
improve the converter’s performance by reducing the
amount of current that is switching at any one time. In
traditional architectures, major transition points required the
converter to switch on or off large amounts of current. In a
traditional 10-bit R/2R ladder design, for example, the
midscale transition required approximately equal amounts of
currents switching on and off. In a segmented current source
arrangement, transitions such as midscale become one in
which you simply have an additional intermediate current
source turning on and several minor ones turning off. In the
case of the HI5728, there are 31 intermediate current
segments that represent the 5 MSBs and five, binary-
3-5
weighted current sources representing each of the five
LSBs. See the Functional Block Diagram in the data sheet
for a visual representation. To relate the midscale transition
example to the HI5728, consider the following: The code
0111111111 would be represented by 15 intermediate
current segments and each of the 5 LSB current sources all
turned on. To transition to code 1000000000 would simply
require turning off the 5 LSB current sources and turning on
the next intermediate current segment, bringing the total
amount of current switching at this ‘major’ code transition
equal to the same amount switching at 30 other code
transition points in the code ramp from 0 to 1023, so that the
total glitch energy is distributed more evenly.
Application Note 9827
Appendix B Pin Description
PIN NO.
PIN NAME
PIN DESCRIPTION
39-30
QD9 (MSB) Through
QD0 (LSB)
Digital Data Bit 9, the Most Significant Bit through Digital Data Bit 0, the Least Significant Bit, of the
Q Channel.
1-6, 48-46
ID9 (MSB) Through
ID0 (LSB)
Digital Data Bit 9, the Most Significant Bit through Digital Data Bit 0, the Least Significant Bit, of the
I Channel.
8
SLEEP
Control Pin for Power-Down mode. Sleep Mode is active high; Connect to ground for Normal Mode. Sleep
pin has internal 20µA active pulldown current.
15
REFLO
Connect to analog ground to enable internal 1.2V reference or connect to AVDD to disable.
23
REFIO
Reference voltage input if internal reference is disabled and reference voltage output if internal reference is
enabled. Use 0.1µF cap to ground when internal reference is enabled.
22
FSADJ
Full Scale Current Adjust. Use a resistor to ground to adjust full scale output current. Full Scale Output
Current Per Channel = 32 x IFSADJ .
14
ICOMP1
For use in reducing bandwidth/noise of I Channel. Recommended: connect 0.1µF to AVDD.
24
QCOMP1
For use in reducing bandwidth/noise of Q Channel. Recommended: connect 0.1µF to AVDD.
13, 18, 19,
25
AGND
Analog Ground Connections.
17
IOUTB
The complimentary current output of the I Channel. Bits set to all 0’s gives full scale current.
16
IOUTA
Current output of the I Channel. Bits set to all 1’s gives full scale current.
20
QOUTB
The complimentary current output of the Q Channel. Bits set to all 0’s gives full scale current.
21
QOUTA
Current output of the Q Channel. Bits set to all 1’s gives full scale current.
11, 27
NC
No Connect. Recommended: connect to ground.
12
AVDD
Analog Supply (+2.7V to +5.5V).
10, 28, 41,
44
DGND
Digital Ground.
3-6
Application Note 9827
Appendix C Circuit Board Layout
FIGURE 3. PRIMARY SIDE
FIGURE 4. GROUND LAYER (2)
3-7
Application Note 9827
Appendix C Circuit Board Layout
(Continued)
FIGURE 5. POWER LAYER (3)
FIGURE 6. SECONDARY SIDE
3-8
Application Note 9827
Power Supply Input Circuit
Ground Symbol Definition
FB2
10µH
= ANALOG GROUND (AGND1)
DVDD1
+
C14
0.1µF
C13
10µF
= DIGITAL GROUND (DGND1)
TO DIGITAL POWER PLANE
PINS 9, 29, 40, 45
OF THE HI5728
TO DIGITAL GROUND PLANE
PINS 10, 28, 41, 44
OF THE HI5728
DGND1
FB1
10µH
AVDD1
+
C9
0.1µF
C8
10µF
TO ANALOG POWER PLANE
PINS 12, 26
OF THE HI5728
(Used if additional circuity is added in the proto area)
VDD1
+
TO ANALOG GROUND PLANE
PINS 13,18, 19, 25
OF THE HI5728
AGND1
Extra Power Supply Input
Located near Output Proto Area
C16
10µF
NOTE: DVDD and AVDD can be tied together for single supply operation.
AGND1 and DGND1 are tied together at a single point. See text for further
explanation.
Extra SMAs
(See ‘Voltage Reference’ text for
explanation.)
Power Supply Decoupling
DVDD Power Decoupling Capacitors
PIN 9
SMA10
PIN 29
PIN 40
PIN 45
E10
0.1µF
C1
E11
0.1µF
C15
0.1µF
C6
0.1µF
C5
SMA11
AVDD Power Decoupling Capacitors
PIN 12
Digital Input Additional Connections
C3
0.1µF
PIN 26
C12
0.1µF
R58 0Ω
QD9
ID9
R60 0Ω
QD8
ID8
R59 0Ω
QD7
Clock Input Circuit
ID7
R54 0Ω
QD6
ID6
SMA8
ICLK
R62 0Ω
QD5
R65 0Ω
VME CONNECTOR
P1-77
CLK
C13
R66 0Ω
ID3
R64 0Ω
QD2
200Ω
R29
R21
50Ω
ID2
ID1
SMA9
QCLK
R67 0Ω
QD0
ID0
3-9
QCLK
PIN 42
200Ω
R63 0Ω
QD1
ICLK
PIN 43
R28
ID4
QD3
R50
0Ω
R49
50Ω
ID5
QD4
(See ‘Clock
Inputs’ Text.)
R53
0Ω
R55
50Ω
Application Note 9827
50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω
R10 R7 R6 R5 R4 R8 R3 R2 R1 R9
VME CONNECTOR (96 OR 64 PIN)
R17
200Ω
R11
A18
P1-18
200Ω
R13
200Ω
R16
P1-79
CLK
200Ω
R19
200Ω
MSB
P1-78
P1-8
A23
SEE CLOCK
INPUT CIRCUIT
R23
R26
C24
P1-9
A10
P1-24
A24
P1-10
A11
P1-11
P1-89
A12
C25
P1-12
P1-25
A13
A25
P1-13
200Ω
R33
200Ω
R37
R40
200Ω
C32
P1-26
P1-96
A26
200Ω
R43
P1-91
P1-87
C27
200Ω
C18
P1-82
P1-92
R45
C3
C28
200Ω
P1-67
LSB
P1-28
A28
QD7
200Ω
R41
C23
QD9 (MSB)
QD8
REFLO
IOUTA
IOUTB
AGND
AGND
QOUTB
QOUTA
FSADJ
REFIO
QCOMP1
200Ω
C26
P1-27
QCLK
DGND
AGND
ICOMP1
R30
P1-90
A27
ICLK
DVDD
200Ω
P1-88
A9
DVDD
DGND
200Ω
P1-77
P1-23
ID9 (MSB)
R20
C14
C13
A8
ID7
ID8
R46
0.1µF
C7
R35
2kΩ
POT
20kΩ
R68
J3
MSB
J2 = AGND - INTERNAL REFERENCE
R15
C15
A14
P1-14
J2 = AVDD - EXTERNAL REFERENCE
200Ω
P1-80
P1-15
J2
200Ω
R14
C16
A15
AVDD POWER PLANE
R18
P1-81
P1-16
DVDD POWER PLANE
200Ω
C17
A16
J1
EXTERNAL REFERENCE = J3 INSTALLED
AND REFLO TIED TO AVDD (SEE J2)
P1-17
200Ω
R12
ID6
ID5
ID4
ID3
ID2
ID1
ID0 (LSB)
SLEEP
DVDD
DGND
NC
AVDD
A17
SLEEP MODE = JUMPER J1 INSTALLED
37 38 39 40 41 42 43 44 45 46 47 48
36
1
35
2
34
3
33
4
32
5
31
6
30
7
29
8
28
9
27
10
26
11
25
12
24 23 22 21 20 19 18 17 16 15 14 13
P1-83
QD6
QD5
QD4
QD3
QD2
QD1
QD0 (LSB)
DVDD
DGND
NC
AVDD
AGND
C19
LSB
THE 50Ω TERMINATIONS ARE
RECOMMENDED IF THE DAC’S
PERFORMANCE IS NOT AS
EXPECTED, ESPECIALLY FOR
CLOCK > 50MSPS.
E2
200Ω
SMA7
R24 R27 R32 R36 R38 R39 R42 R44 R47 R48
50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω
3-10
EXTERNAL REFERENCE
(OPTIONAL)
Application Note 9827
Ground Connection
Rgnd 0Ω
Digital Ground Plane
Analog Ground Plane
NOTE: AGND1 and DGND1 are tied together at a single point near the
DAC. Optimum placement for Rgnd was found by iteration while observing
the spectral noise floor.
TP2
ANALOG
GROUND
TP1
DIGITAL
GROUND
E4 E5
ICOMP1
0Ω
R56
SMA1
E6
R22
50Ω
IOUT
SMA5
V OUT = (2 x I OUT x R EQ)V
0Ω
R57
100Ω
IOUTA
SMA2
IOUTB
R61
0Ω
SMA3
QOUTB
R25
50Ω
R51
0Ω
R31
50Ω
0Ω
R70
QOUTA
100Ω
R69
0Ω
SMA4
E7
QCOMP1
0.1µF
C10
0.1µF
C4
R34
50Ω
R72
0Ω
50Ω
R52
50Ω REPRESENTS THE SPECTRUM
ANALYZER INPUT IMPEDANCE.
R71
50Ω
QOUT
SMA6
V OUT = (2 x Q OUT x R EQ)V
50Ω IS THE SPECTRUM ANALYZER
INPUT IMPEDANCE.
E9 E8
AVDD POWER PLANE
NOTE: E6 was mistakenly grounded so R56 should not be populated! E7, however, is correct and can be used to overdrive the internal reference
op amp for increasing the multiplying bandwidth.
3-11
Application Note 9827
Appendix D Evaluation Board Bill Of Materials
REFERENCE DESIGNATOR
QTY
DESCRIPTION
U1
1
HI5728IN, Intersil Dual 10-bit D/A Converter
C8, 13, 16
3
10µF, Tantalum Chip Capacitor, EIA Case B, 10%, 10V
C1-7, 9-12, 14, 15
13
0.1µF, Ceramic Chip Capacitor, 0805, 10%, 10V
R1-10, 21, 24, 27, 32, 36, 38, 39, 42, 44, 47-49, 55
23
Included, not populated51Ω, Chip Resistor, 1210, 5%, 1/4W
R11-20, 23, 26, 28, 29, 30, 33, 37, 40, 41, 43, 45, 46, 51, 57, 70
25
200Ω, Chip Resistor, 0805, 1/8W
R52, 71
2
100Ω, Chip Resistor, 0805, 1/8W
R22, 25, 31, 34
4
51Ω, Chip Resistor, 0805, 1/8W
R54, 58, 59, 60-67, 69
12
0Ω, Chip Resistor, 0402, 1/10W
R68
1
20kΩ, Potentiometer Resistor, 3296W, 1/8W(Shipped set to
~2kΩ)
R35
1
(2kΩ, Chip Resistor, 0805, 1/8W) (Not Populated)
J1, J2
2
1x2 Header
J3
1
1x3 Header
T1, 2
2
Mini-Circuits, T1-1T KK81, Z1:Z2 ratio of 1:1
P1
1
96-Pin Eurocard, Right Angle
SMA1-11
11
SMA Straight Jack, PCB Mount
FB1, 2
2
10µH, Ferrite Bead
TP1, 2
2
Test Point
-
3
1x2 Header Jumper
-
-
DUT Clamp
-
4
Plastic Legs, 1/2”
R50, 53, Rgnd
3
(0Ω, Chip Resistor, 0805, 1/8W) (R50, 53 Not Populated)
R56
1
(0Ω, Chip Resistor, 0402, 1/10W) (Not Populated )
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
3-12