el1502

EL1502
S
ESIGN
To request the full datasheet, please visit www.intersil.com/products/EL1502
NE W D NT
R
O
F
E
EN D ED R E PL A C EM
M
M
t
O
a
EC
enter
ENDED uData
N OT R
October 12, 1999
FN7037
pport CSheet
CO MM
NO RE r Technical S x311
C
u
E
o
T
t
contac 1-888-ELAN
The EL1502 is a complete transceiver
solution for high speed data
transmission over twisted pair wires. It
contains two wideband, high-voltage drivers and two lownoise receive amplifiers. The EL1502 is ideally suited for
both ADSL and HDSL2 applications, in which it can supply a
50VP-P signal into a 50 differential load while exhibiting
very low distortion. The receive amplifiers also have very low
distortion and low-noise for superior reception of small
signals.
The line drivers of the EL1502 are current-feedback type
amplifiers, which achieve a high slew rate while consuming
moderate power. They retain their frequency response over
a wide range of externally set gains. The receive amplifiers
are of the voltage-feedback type and can be used to
implement a hybrid coupler or filter functions using external
passive components.
Features
• Complete ADSL differential driver and receiver
• 54VP-P output drive into 100 differential
• 50VP-P output drive into 50 differential
• Driver 2nd/3rd harmonics of -70dBc/-75dBc at 2VP-P into
100
• Low supply current 12.5mA per drive amplifier and 5mA
per receive amplifier
• Standard surface-mount package
Applications
• ADSL line driver
• HDSL2 line driver
• Video distribution amplifier
Pinout
EL1502
(20-PIN SO)
TOP VIEW
The EL1502 operates on ±5V to ±15V supplies. It retains its
bandwidth and linearity over the complete supply range.
Ordering Information
PART NUMBER
PACKAGE
EL1502CM
20-Pin SO
TAPE & REEL PKG. DWG. #
-
20 VIN-D2
VIN-D1 1
VOUTD1 2
19 VOUTD2
VS- 3
18 VS+
+
The device is supplied in a standard form factor, 20-pin
SOIC package. The eight center package pins of the
package are used as ground connections and heat
spreaders, allowing for operation over the full -40°C to
+85°C temperature range.
+
High Power Differential Line Driver/
Receiver
GND* 4
17 GND*
GND* 5
16 GND*
GND* 6
15 GND*
GND* 7
14 GND*
MDP0027
VIN+D1 8
VOUT+R1 9
VIN-R1 10
13 VIN+D2
+
-
+
-
12 VOUT+R2
11 VIN-R2
NOTE: * GND PINS ARE HEAT SPREADERS
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc.
All other trademarks mentioned are the property of their respective owners.
EL1502
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9001 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
2