ELANTEC EL1502C

High Power Differential Line Driver/Receiver
Features
General Description
• Complete ADSL differential driver
and receiver
• 54VP-P output drive into 100Ω
differential
• 50VP-P output drive into 50Ω
differential
• Driver 2nd/3rd harmonics of
-70dBc/-75dBc at 2VP-P into 100Ω
• Low supply current - 12.5mA per
drive amplifier and 5mA per
receive amplifier
• Standard surface-mount package
The EL1502C is a complete transceiver solution for high speed data
transmission over twisted pair wires. It contains two wideband, highvoltage drivers and two low-noise receive amplifiers. The EL1502C is
ideally suited for both ADSL and HDSL2 applications, in which it can
supply a 50VP-P signal into a 50Ω differential load while exhibiting
very low distortion. The receive amplifiers also have very low distortion and low-noise for superior reception of small signals.
Applications
The device is supplied in a standard form factor, 20-pin SOIC package. The eight center package pins of the package are used as ground
connections and heat spreaders, allowing for operation over the full --40°C to +85°C temperature range.
Ordering Information
Part No
Package
20-Lead SO
Tape & Reel
The line drivers of the EL1502C are current-feedback type amplifiers,
which achieve a high slew rate while consuming moderate power.
They retain their frequency response over a wide range of externally
set gains. The receive amplifiers are of the voltage-feedback type and
can be used to implement a hybrid coupler or filter functions using
external passive components.
The EL1502C operates on ±5V to ±15V supplies. It retains its bandwidth and linearity over the complete supply range.
• ADSL line driver
• HDSL2 line driver
• Video distribution amplifier
EL1502CM
Outline #
MDP0027
Connection Diagrams
VIN-D1 1
20 VIN-D2
VOUTD1 2
19 VOUTD2
18 VS+
+
+
VS- 3
GND* 4
17 GND*
GND* 5
16 GND*
GND* 6
15 GND*
GND* 7
14 GND*
VOUT+R1 9
VIN-R1 10
13 VIN+D2
+
-
+
-
12 VOUT+R2
11 VIN-R2
20-Pin Wide Body SOIC
* Gnd pins are heat spreaders
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
October 12, 1999
VIN+D1 8
© 2001 Elantec Semiconductor, Inc.
EL1502C - Product Brief
EL1502C - Product Brief
EL1502C - Product Brief
EL1502C - Product Brief
High Power Differential Line Driver/Receiver
General Disclaimer
Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the circuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described
herein and makes no representations that they are free from patent infringement.
October 12, 1999
WARNING - Life Support Policy
Elantec, Inc. products are not authorized for and should not be used
within Life Support Systems without the specific written consent of
Elantec, Inc. Life Support systems are equipment intended to support or sustain life and whose failure to perform when properly used
in accordance with instructions provided can be reasonably
expected to result in significant personal injury or death. Users contemplating application of Elantec, Inc. Products in Life Support
Systems are requested to contact Elantec, Inc. factory headquarters
to establish suitable terms & conditions for these applications. Elantec, Inc.’s warranty is limited to replacement of defective
components and does not cover injury to persons or property or
other consequential damages.
Elantec Semiconductor, Inc.
675 Trade Zone Blvd.
Milpitas, CA 95035
Telephone: (408) 945-1323
(888) ELANTEC
Fax:
(408) 945-9305
European Office: +44-118-977-6020
Japan Technical Center: +81-45-682-5820
2
Printed in U.S.A.