DATASHEET

Single Port, VDSL2 Differential Line Driver
ISL1550
Features
The ISL1550 is a dual operational amplifier intended to be
used as a differential line driver. ISL1550’s high bandwidth
and low distortion performance enables the support of VDSL2
8b, 17a and 30a modem applications.
• 20dBm output power capability
This device features a high current drive capability of ±750mA
required to drive large voltage peaks into heavy loads. In
Central Office (CO) applications, the driver achieves a typical
Missing Band Power Ratio (MBPR) of -66dBc in VDSL2 8b
upstream (US) 1 band and MBPR’s of -61dBc and -60dBc in
VDSL2 17a US1 and US2 respectively.
The ISL1550 has two bias current control pins (C0, C1) to allow
for four power settings (disable, low, medium, high). The VDSL
modem DSP configures the line driver’s power setting based
on the desired mode of operation. The line driver operates on a
nominal single +12V or a dual ±6V supplies with bias current
in active mode between 15mA to 32mA, depending on its
power setting. The ISL1550’s gain setting is configurable at
the application level by setting the Rf and Rg resistor values.
The surge current handling of ISL1550 has been enhanced to
allow ITU-T K.20 and GR1089 compliance with minimal
external surge protection circuitry.
The ISL1550 is available in the thermally-enhanced, Pb-free
RoHS compliant 16 Ld QFN package and is specified for
operation over the full -40°C to +85°C temperature range.
SUPPLY
DECOUPLING
NOT SHOWN
+
500
100n
• K.20, GR-1089 Surge Robustness Validated
Applications
• VDSL2 Profiles: 8MHz, 17MHz, and 30MHz
Related Literature
• AN1325 “Choosing and Using Bypass Capacitors”
TABLE 1. ALTERNATE SOLUTIONS
PART #
NOMINAL ±VCC
(V)
BANDWIDTH
(MHz)
APPLICATIONS
ISL1557
±6,+12
200
VDSL2
ISL1539A
±12,+24
240
VDSL2
-80
1:2.5
Rg
1.5k
1k
2.2n
1k
Rf
750
½
ISL1550
-100
-110
-120
-130
2.2
+
FIGURE 1. TYPICAL APPLICATION CIRCUIT
1
-90
100
NOMINAL
LINE
-6V
March 16, 2012
FN6795.0
• Supply range: ±4.0V to ±6.6V, +8.0V to +13.2V
• Thermal shutdown
-70
2.2
Rf
750
500
• -61dBc US1, -60dBc US2 avg. MBPR 17a
-60
½
ISL1550
-
• -89dBc typical driver output distortion at full output at
200kHz, 12VP-P differential
-50
AFE
• 18VP-P differential output drive into 20Ω
-40
+6V
100n
• Drives up to ±750mA from a +12V supply
-140
8.40M
8.90M
9.40M
9.90M
10.4M
10.9M
11.4M
11.9M
FREQUENCY (Hz)
FIGURE 2. US2 MBPR 17a VDSL2 PERFORMANCE
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2012. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
ISL1550
Connection Diagram
+ +
+6V
INA
+
+
25
OUTA
½ ISL1550
-
1.5k
INA2VP-P
750
10VP-P
5VP-P
into 50
INB-
1.5k
½ ISL1550
+
OUTB
BIAS
CURRENT
CONTROL
INB
+
25
C0
C1
GND
+ +
Av = (1.5k / (750/2)) + 1 = 5V/V
-6V
FIGURE 3. TYPICAL DIFFERENTIAL AMPLIFIER I/O
Pin Configuration
OUTA
NC
VS+
OUTB
ISL1550
(16 LD QFN)
TOP VIEW
16
15
14
13
NC 1
12 NC
INA- 2
11 INBVS-*
INA+ 3
10 INB+
5
6
7
8
NC
VS-
C0
9
NC
GND 4
C1
*THERMAL PAD CONNECTS TO MOST NEGATIVE SUPPLY
2
FN6795.0
March 16, 2012
ISL1550
Pin Descriptions
PIN NUMBER
PIN NAME
1
NC
No Connect
FUNCTION
2
INA-
Amplifier A Inverting Input
3
INA+
Amplifier A Non-Inverting Input
4
GND
5
NC
No Connect
6
NC
No Connect
7
VS-
Negative Supply Voltage
8
C0
Digital Control Pin
9
C1
Digital Control Pin
10
INB+
Amplifier B Non-Inverting Input
11
INB-
Amplifier B Inverting Input
Ground
12
NC
13
OUTB
No Connect
14
VS+
Positive Supply Voltage
15
NC
No Connect
16
OUTA
Amplifier B Output
Amplifier A Output
Ordering Information
PART
NUMBER
(Notes 2, 3)
PART
MARKING
TEMP RANGE
(°C)
PACKAGE
(Pb-free)
PKG.
DWG. #
ISL1550IRZ
155 0IRZ
-40 to +85
16 Ld QFN
L16.4x4H
ISL1550IRZ-T7 (Note 1)
155 0IRZ
-40 to +85
16 Ld QFN
L16.4x4H
ISL1550IRZ-T13 (Note 1)
155 0IRZ
-40 to +85
16 Ld QFN
L16.4x4H
ISL1550IRZ-EVALZ
Evaluation Board
NOTES:
1. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL1550. For more information on MSL please see tech brief TB363.
3
FN6795.0
March 16, 2012
ISL1550
Absolute Maximum Ratings (TA = +25°C)
Thermal Information
VS+ Voltage to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +13.2V
Driver VIN+ Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GND to +VS
C0, C1 Voltage to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +VS
Current into any Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8mA
Continuous Output Current for Long Term Reliability. . . . . . . . . . . . . . . . .50mA
ESD Rating
Human Body Model (Tested per JESD22-A114F). . . . . . . . . . . . . . . . . . 4kV
Machine Model (Tested per JESD22-A115C) . . . . . . . . . . . . . . . . . . 300V
Charge Device Model (Tested per JESD22-C101E). . . . . . . . . . . . . .1.5kV
Thermal Resistance (Typical)
θJA (°C/W) θJC (°C/W)
16 Ld QFN Package (Notes 4, 5) . . . . . . . .
53
16.5
Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . .+150°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-40°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Ambient Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . .-40°C to +150°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
5. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications
PARAMETER
VS = ±6V, see Figure 1, TA = +25°C, unless otherwise specified.
DESCRIPTION
CONDITIONS
MIN
(Note 6)
TYP
MAX
(Note 6)
UNIT
AC PERFORMANCE
BW
-3dB Bandwidth
See Figure 1
105
MHz
THD
Total Harmonic Distortion, Differential
f = 200kHz, VO = 12VP-P output, RL = 20Ω
-89
dBc
f = 4MHz, VO = 12VP-P output, RL = 100Ω
-67
dBc
f = 10MHz, VO = 12VP-P output, RL = 100Ω
-61
dBc
2400
V/µs
SR
Slew Rate (20% to 80%)
VOUT from -6V to +6V (differential)
1500
DC PERFORMANCE
VOS_CM
Input Offset Voltage Common Mode
-45
+45
mV
VOS_DM
Input Offset Voltage Differential Mode
-7.5
+7.5
mV
INPUT CHARACTERISTICS
IB+
Non-Inverting Input Bias Current
-7.0
-3.0
+7.0
µA
IB- DM
Inverting Input Bias Current Differential
Mode
-45
±7
+45
µA
eO
Differential Output Noise
See Figure 1 [at transformer input]
45
nV√ Hz
±5.0
V
±4.5
V
OUTPUT CHARACTERISTICS
VOUT
Loaded Output Swing (single-ended)
VS = ±6V, RL DIFF = 100Ω
±4.7
VS = ±6V, RL DIFF = 20Ω
SUPPLY
+VS
Supply Voltage
Single supply (-VS = GND)
8.0
12
13.2
V
IS+ (Full Bias)
Positive Supply Current
All outputs at 0V, C0 = C1 = 0V
27
32
37
mA
IS+ (Medium Bias)
Positive Supply Current
All outputs at 0V, C0 = 5V, C1 = 0V
19
23
26
mA
IS+ (Low Bias)
Positive Supply Current
All outputs at 0V, C0 = 0V, C1 = 5V
12
15
18
mA
IS+ (Power down)
Positive Supply Current
All outputs at 0V, C0 = C1 = 5V
1.3
1.6
2.5
mA
IINH, C0 or C1
C0, C1 Input Current, High
C0, C1 = 6V
100
165
224
µA
IINL, C0 or C1
C0, C1 Input Current, Low
C0, C1 = 0V
-1.5
-1.0
+1.5
µA
VINH, C0 or C1
C0, C1 Input Voltage, High
VINL, C0 or C1
C0, C1 Input Voltage, Low
2.0
V
0.8
V
NOTE:
6. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
4
FN6795.0
March 16, 2012
ISL1550
Typical Performance Curves
noted.
VCC = ±6V, See Figure 1, TA = +25°C, C0 = C1 = 0V (Full power), Unless otherwise
6
6
3
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
3
25Ω
0
50Ω
-3
-6
16Ω
-9
-12
0
33pF
-3
-6
22pF
-9
1M
10M
100M
-12
1G
1M
10M
1G
FIGURE 5. SMALL SIGNAL FREQUENCY RESPONSE vs CLOAD
6
6
3
3
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
FIGURE 4. SMALL SIGNAL FREQUENCY RESPONSE vs RLOAD
0
-3
VCC = 12V TO 8V
-6
-9
1VP-P
0
5VP-P
-3
-6
2VP-P
-9
1M
10M
100M
FREQUENCY (Hz)
-12
1G
FIGURE 6. SMALL SIGNAL BANDWIDTH vs SUPPLY VOLTAGE
-50
THD
-60
-70
-80
-90
-100
1M
10M
100M
FREQUENCY (Hz)
1G
-40
5VOP-P-DIFF
100Ω RLOAD
HARMONIC DISTORTION (dBc)
-40
1M
FIGURE 7. LARGE SIGNAL FREQUENCY RESPONSE
-30
HARMONIC DISTORTION (dBc)
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
-12
18pF
3rd HD
2nd HD
10M
FREQUENCY (Hz)
FIGURE 8. HARMONIC DISTORTION vs FREQUENCY
5
100M
100Ω RLOAD
-45
-50
-55
-60
THD
-65
-70
-75
2nd HD
-80
-85
-90
3rd HD
1
10
VOP-P-LOAD (V)
FIGURE 9. 4MHz HARMONIC DISTORTION vs OUTPUT VOLTAGE
FN6795.0
March 16, 2012
ISL1550
Typical Performance Curves
noted. (Continued)
VCC = ±6V, See Figure 1, TA = +25°C, C0 = C1 = 0V (Full power), Unless otherwise
-45
-40
100Ω RLOAD
HARMONIC DISTORTION (dBc)
HARMONIC DISTORTION (dBc)
-40
-50
-55
THD
-60
-65
-70
-75
2nd HD
-80
3rd HD
-85
-90
1
-50
THD
-55
-60
-65
-70
2nd HD
3rd HD
-75
-80
-85
-90
10
100Ω RLOAD
-45
1
10
VOP-P-LOAD (V)
VOP-P-LOAD (V)
FIGURE 11. 20MHz HARMONIC DISTORTION vs OUTPUT VOLTAGE
FIGURE 10. 10MHz HARMONIC DISTORTION vs OUTPUT VOLTAGE
-20
-30
-30
-40
-50
-60
-60
MTPR (dBm)
-50
-70
-80
-90
-80
-90
-100
-110
-110
-120
-120
-130
-130
-140
3.78M
3.98M
4.18M
4.38M
4.58M
4.78M
4.98M
-140
5.18M
PAR = 6.3/V
14.5dBm LINE POWER, RL = 25Ω,
AVG. MBPR = -60dBc
-70
-100
8.48M
8.98M
FREQUENCY (Hz)
9.48M 9.98M 10.5M
FREQUENCY (Hz)
11M
11.5M
FIGURE 13. MBPR 17a US2
FIGURE 12. MBPR 8b US1
100
LOW POWER
nV/√Hz
MTPR (dBm)
-40
-20
PAR = 5.32/V
18dBm LINE POWER, RL = 25Ω,
AVG. MBPR = -66dBc
MEDIUM POWER
FULL POWER
Fig. 1 at transformer inputs
10
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FIGURE 14. DIFFERENTIAL OUTPUT NOISE
6
FN6795.0
March 16, 2012
ISL1550
Typical Performance Curves
otherwise noted.
VCC = ±6V, See Figure 1, TA = +25°C, C0 = 3.3V, C1 = 0V (Medium power), Unless
6
3
3
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
6
25Ω
0
50Ω
-3
-6
16Ω
-9
-12
1M
10M
100M
0
-6
22pF
-9
-12
1M
1G
10M
FREQUENCY (Hz)
6
-30
3
-40
1VP-P
0
5VP-P
-3
-6
2VP-P
-9
-12
1M
10M
100M
1G
-50
THD
-60
-70
3rd HD
-80
2nd HD
-90
-100
1M
10M
100M
FREQUENCY (Hz)
FIGURE 18. HARMONIC DISTORTION vs FREQUENCY
FIGURE 17. LARGE SIGNAL FREQUENCY RESPONSE
-40
-40
100Ω RLOAD
-45
-50
-55
-60
THD
-65
-70
-75
2nd HD
-80
-85
3rd HD
1
10
VOP-P-LOAD (V)
FIGURE 19. 4MHz HARMONIC DISTORTION vs OUTPUT VOLTAGE
7
HARMONIC DISTORTION (dBc)
HARMONIC DISTORTION (dBc)
1G
5VOP-P-DIFF
100Ω RLOAD
FREQUENCY (Hz)
-90
100M
FREQUENCY (Hz)
FIGURE 16. SMALL SIGNAL FREQUENCY RESPONSE vs CLOAD
HARMONIC DISTORTION (dBc)
NORMALIZED GAIN (dB)
FIGURE 15. SMALL SIGNAL FREQUENCY RESPONSE vs RLOAD
18pF
33pF
-3
100Ω RLOAD
-45
-50
-55
THD
-60
-65
-70
2nd HD
-75
-80
3rd HD
-85
-90
1
VOP-P-LOAD (V)
10
FIGURE 20. 10MHz HARMONIC DISTORTION vs OUTPUT VOLTAGE
FN6795.0
March 16, 2012
ISL1550
Typical Performance Curves
otherwise noted.
VCC = ±6V, See Figure 1, TA = +25°C, C0 = 0V, C1 = 3.3V (Low power), unless
6
3
3
25Ω
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
6
0
50Ω
-3
-6
16Ω
-9
-12
1M
10M
100M
0
33pF
-3
-6
22pF
-9
-12
1G
1M
10M
FREQUENCY (Hz)
3
-40
HARMONIC DISTORTION (dBc)
NORMALIZED GAIN (dB)
-30
1VP-P
5VP-P
-6
2VP-P
-9
-12
1M
10M
100M
1G
5VOP-P-DIFF
100Ω RLOAD
-50
THD
-60
-70
3rd HD
2nd HD
-80
-90
-100
1M
10M
FIGURE 24. HARMONIC DISTORTION vs FREQUENCY
FIGURE 23. LARGE SIGNAL FREQUENCY RESPONSE
-40
100Ω RLOAD
-50
-55
-60
THD
-65
-70
-75
-80
2nd HD
-85
3rd HD
VOP-P-LOAD (V)
10
FIGURE 25. 4MHz HARMONIC DISTORTION vs OUTPUT VOLTAGE
8
HARMONIC DISTORTION (dBc)
HARMONIC DISTORTION (dBc)
-40
-90
1
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
-45
1G
FIGURE 22. SMALL SIGNAL FREQUENCY RESPONSE vs CLOAD
6
-3
100M
FREQUENCY (Hz)
FIGURE 21. SMALL SIGNAL FREQUENCY vs RLOAD
0
18pF
100Ω RLOAD
-45
-50
-55
THD
-60
-65
-70
-75
3rd HD
-80
2nd HD
-85
-90
1
10
VOP-P-LOAD (V)
FIGURE 26. 10MHz HARMONIC DISTORTION vs OUTPUT VOLTAGE
FN6795.0
March 16, 2012
ISL1550
Typical Performance Curves
TA = +25°C, C0 and C1 Varied, unless otherwise noted.
VCC = ±6V, See Figure 3, Gain = 5V/V (Differential), Rf = 1.5kΩ, RLOAD = 100Ω,
-30
-40
13.5
VS = ±6V
12.5 VS = ±6V
11.5 RF = 750Ω
AV = 5
DIFFERENTIAL (Ω)
-60 RLOAD = 100Ω
VIN = 1VP-P DIFF
-70
-80
-90
10.5
9.5
4.5
10M
FREQUENCY (Hz)
100M
FULL POWER
MEDIUM POWER
6.5
-110
1M
RL = 100Ω DIFF
7.5
5.5
-120
100k
RG = 374Ω
8.5
-100
LOW POWER
3.5
100k
1G
1M
10M
FREQUENCY (Hz)
100M
FIGURE 28. DIFFERENTIAL OUTPUT IMPEDANCE
FIGURE 27. OFF-ISOLATION
T = 0s
T = 1.60000µs
C0, C1 PIN
2V/DIV
C0, C1 PIN
2V/DIV
Output Sine Wave
OUTPUT PIN
5V/DIV
OUTPUT PIN
5V/DIV
300ns
FIGURE 29. POWER ON
FIGURE 30. POWER OFF
40
T = 242.800ns
FULL POWER(mA)
35
OUTPUT A
2V/DIV
OUTPUT B
QUIESCENT CURRENT (mA)
GAIN (dB)
-50 RF = 750Ω
30
25
MEDIUM POWER
20
15
LOW POWER
10
5
Figure 1
0
-40 -30 -20 -10
0
10
20
30
40
50
60
70
80
TEMPERATURE (°C)
FIGURE 31. OVERDRIVE RECOVERY
9
FIGURE 32. QUIESCENT CURRENT vs TEMPERATURE
FN6795.0
March 16, 2012
ISL1550
Typical Performance Curves
VCC = ±6V, See Figure 3, Gain = 5V/V (Differential), Rf = 1.5kΩ, RLOAD = 100Ω,
TA = +25°C, C0 and C1 Varied, unless otherwise noted. (Continued)
-80
-60
12VP-P-D
20Ω RLOAD
-62
-84
-64
-86
-66
-88
-68
HD (dBc)
HD (dBc)
-82
-90
-92
2nd HD
-94
-96
-70
-72
-74
3rd HD
-76
-98
Figure 1
-100
-40 -30 -20 -10
2nd HD
-78
0
10
20
30
40
50
60
70
TEMPERATURE(°C)
FIGURE 33. 200kHz DISTORTION vs TEMPERATURE
10
80
Figure 1
-80
-40 -30 -20 -10
3rd HD
0
10
20
30
40
50
60
70
80
TEMPERATURE(°C)
FIGURE 34. 4MHz DISTORTION vs TEMPERATURE
FN6795.0
March 16, 2012
ISL1550
Applications Information
Product Description
The ISL1550 is a dual operational amplifier designed for line driving
in DMT VDSL2 8MHz, 12MHz, 17MHz and 30MHz bandplans
solutions. It is a current mode feedback amplifier with low distortion
drawing moderately low supply current. Due to the current feedback
architecture, the ISL1550 closed-loop 3dB bandwidth is dependent
on the value of the feedback resistor. First, the desired bandwidth is
selected by choosing the feedback resistor, RF, and then the gain is
set by picking the gain resistor, RG (Figure 3).
VDSL CO Applications
The ISL1550 is designed as a VDSL line driver for CO. At an
output current of ±450mA, the typical supply voltage headroom
is 1.5V on each side of the differential output.
The average line power requirement for the VDSL CO application
is 20dBm (100mW) into a 100Ω line. The average line voltage is
3.16VRMS. The VDSL DMT peak-to-average ratio (crest factor) of
5.3 implies peak voltage of 16.8VP into the line. Using a
differential drive configuration and transformer coupling with
standard back termination, a transformer ratio of 1:2.5 is
selected. The active termination technique provides better power
efficiency by reducing the backmatch resistor by a factor of
K = 5. Positive feedback resistors, RP, can be sized to make the
effective backmatch impedance larger. The circuit configuration
is shown in Figure 35.
12.5/k
+
-
750Ω
RP
TX1
100
AFE
1:2.5
1.5kΩ
+
750Ω
RP = RF(K/(K-1))
FIGURE 35. CIRCUIT CONFIGURATION
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, good printed circuit board
layout is necessary for optimum performance. Ground plane
construction is highly recommended. Lead lengths should be as
short as possible (below 0.25”). The power supply pins must be
well bypassed to reduce the risk of oscillation. A 4.7µF tantalum
capacitor in parallel with a 0.1µF ceramic capacitor is adequate
11
For good AC performance, parasitic capacitances should be kept
to a minimum, especially at the inverting input. This implies
keeping the ground plane away from this pin. Carbon or metal
film resistors are acceptable, while use of wire-wound resistors
should be avoided because of their parasitic inductance.
Similarly, capacitors should be low inductance for best
performance.
Capacitance at the Inverting Input
Due to the topology of the current feedback amplifier, stray
capacitance at the inverting input will affect the AC and transient
performance of the ISL1550 when operating in the non-inverting
configuration.
Feedback Resistor Values
The ISL1550 has been designed and specified with RF = 1.5kΩ
for AV = +5 (Figure 3). As is the case with all current feedback
amplifiers, wider bandwidth at the expense of slight peaking, can
be obtained by reducing the value of the feedback resistor.
Inversely, larger values of the feedback resistor will cause rolloff
to occur at a lower frequency.
Quiescent Current vs Temperature
The ISL1550 was designed to slightly increase quiescent current
with temperature to maintain good distortion performance at
high temperatures. Refer to “Typical Performance Curves”
beginning on page 5.
Supply Voltage Range
RPΩ
12.5/k
for each supply pin. During power-up, it is necessary to limit the
slew rate of the rising power supply to less than 1V/µs. If the
power supply rising time is undetermined, a series 10Ω resistor
on the power supply line before the decoupling caps can be used
to ensure the proper power supply rise time.
The ISL1550 has been designed to operate with supply voltages
from ±4.0V to ±6.6V nominal. Optimum bandwidth, slew rate,
and video characteristics are obtained at higher supply voltages.
Single Supply Operation
If a single supply is desired, values from +8.0V to +13.2V
nominal can be used as long as the input common mode range
is not exceeded. When using a single supply, be sure to either,
1. DC bias the inputs at an appropriate common mode voltage
and AC-couple the signal, or
2. Ensure the driving signal is within the common mode range of
the ISL1550.
FN6795.0
March 16, 2012
ISL1550
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you
have the latest revision.
DATE
REVISION
March 16, 2012
FN6795.0
CHANGE
Initial release.
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products
address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks.
Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a
complete list of Intersil product families.
For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page on
intersil.com: ISL1550
To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
12
FN6795.0
March 16, 2012
ISL1550
Package Outline Drawing
L16.4x4H
16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
Rev 0, 1/12
2.40
4X 1.95
4.00
12X 0.65
A
B
13
6
PIN 1
INDEX AREA
6
PIN #1
INDEX AREA
16
1
4.00
12
2.40
9
(4X)
4
0.15
5
8
0.10 M C A B
16x 0.550±0.05
TOP VIEW
BOTTOM VIEW
4 0.30 ±0.05
SEE DETAIL "X"
0.90±0.10
0.10 C
C
BASE PLANE
SEATING PLANE
( 3 . 6 TYP )
SIDE VIEW
(
(12x0.65)
2.40)
(16x0.30)
C
0 . 20 REF
5
(16x0.75)
+0.03/-0.02
TYPICAL RECOMMENDED LAND PATTERN
DETAIL "X"
NOTES:
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2.
Dimensioning and tolerancing conform to ASME Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4.
Dimension applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
5.
Tiebar shown (if present) is a non-functional feature.
6.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
13
FN6795.0
March 16, 2012