EL7412 ® CT T O D U C E M EN t R P E A ra T L e E P t en OL RE C S D t B r E O /tsc o D Sheet .com MEN cal Supp ersData l i M O EC hni .int NO R our Tec or www t L c I a cont -INTERS 8 8 8 1 High Speed, Four Channel Power MOSFET Drivers August 26, 2004, Rev B FN7287.1 Features • Excellent response times The EL7412 contains (4) high performance matched drivers. These very high speed drivers are capable of delivering peak currents of 2.0 amps into highly capacitive loads and are ideally suited for “Full bridge' and ultrasound applications. The high speed performance is achieved by means of a proprietary “Turbo-Driver' circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. The matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10 fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with nonoverlapped drive techniques. • Matched rise and fall times • Reduced clock skew • Low output impedance • Low input capacitance • High noise immunity • Improved clocking rate • Low supply current • Wide operating voltage range • Pb-free available Applications • Full bridge drivers • Clock/line drivers Pinout EL7412 [20-PIN SO (0.300”)] TOP VIEW • CCD Drivers • Ultra-sound transducer drivers • Power MOSFET drivers • Switch mode power supplies • Class D switching amplifiers • Ultrasonic and RF generators • Pulsed circuits Ordering Information PACKAGE TAPE & REEL PKG. DWG. # EL7412CM 20-Pin SO (0.300”) - MDP0027 EL7412CM-T13 20-Pin SO (0.300”) 13” MDP0027 EL7412CMZ (See Note) 20-Pin SO (0.300”) (Pb-free) - MDP0027 EL7412CMZT13 (See Note) 20-Pin SO (0.300”) (Pb-free) 13” MDP0027 PART NUMBER Note 1: Pins 4–7 and 14–17 are electrically connected. Manufactured under U.S. Patent Nos. 5,334,883, #5,331,047 NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which is compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J-Std-020C. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Elantec Semiconductor, Inc. 1996, Intersil Americas Inc. 2004. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc. All other trademarks mentioned are the property of their respective owners. EL7412 Absolute Maximum Ratings (TA = 25°C) Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125°C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves Supply (V+ to Gnd) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5V Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.3V above V+ Combined Peak Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . .8A Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA DC Electrical Specifications PARAMETER TA = 25°C, VDD = 15V unless otherwise specified DESCRIPTION TEST CONDITIONS MIN TYP MAX UNITS INPUT VIH Logic “1' Input Voltage IIH Logic “1' Input Current VIL Logic “0' Input Voltage IIL Logic “0' Input Current VHVS Input Hysteresis 2.4 @VDD V 0.1 @0V 0.1 10 µA 0.8 V 10 µA 0.3 V OUTPUT ROH Pull-Up Resistance IOUT = -100mA 3 6 Ω ROL Pull-Down Resistance IOUT = +100mA 4 6 Ω IPK Peak Output Current Source Sink 2 2 IDC Continuous Output Current Source/Sink IS Power Supply Current Inputs High VS Operating Voltage A 100 mA POWER SUPPLY AC Electrical Specifications PARAMETER 2 5 mA 15 V TYP MAX UNITS CL = 500pF CL = 1000pF 7.5 10 20 4.5 TA = 25°C, V = 15V unless otherwise specified DESCRIPTION TEST CONDITIONS MIN SWITCHING CHARACTERISTICS tR Rise Time tF Fall Time CL = 500pF CL = 1000pF 10 13 20 ns tD1 Turn-On Delay Time See Timing Table 18 25 ns tD2 Turn-Off Delay Time See Timing Table 20 25 ns 2 ns EL7412 Timing Table Standard Test Configuration Simplified Schematic 3 EL7412 Typical Performance Curves Max Power/Derating Curves Switch Threshold vs Supply Voltage Ambient Temperature (°C) Peak Drive vs Supply Voltage Input Current vs Voltage “ON' Resistance vs Supply Voltage 4 EL7412 Typical Performance Curves (Continued) Average Supply Current vs Voltage and Frequency Rise/Fall Time vs Load 5 Average Supply Current vs Capacitive Load Rise/Fall Time vs Supply Voltage EL7412 Typical Performance Curves (Continued) Propagation Delay vs Supply Rise/Fall Time vs Temperature Delay vs Temperature All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 6