Quick Manual

NANO830/831 Series Quick Installation Guide
9 CPU Board x1
9 Quick Installation Guide x1
9 Product Information CD x1
9 COM Port Cable with Bracket,
P=2.0mm x1
Note: Please contact your local vendors if any damaged or missing items. DO
NOT apply power to the board if there is any damaged component.
Note: Please refer to the NANO830/831 series product information CD for the
complete user’s manual, drivers and utilities. User’s manual and related
documents are in Acrobat PDF format.
Note: After installing graphics driver and rebooting the computer, the display
is in extended mode. Please click hot key <Ctrl+Alt+F1> to switch
display back to single mode.
Connectors
Bottom View
Quick Start
The basic procedures required to power on NANO830/831:
(1). Require at least 60W DC adapter. Ensure that all necessary
peripheral devices are plugged properly.
(2). Check the jumper settings and make sure they are in the
default position; especially JP10 (close).
(3). Firmly install DDR3 memory modules into connector SDIMM1
until fully seated.
(4). Firmly insert the DC adapter into CN17.
(5). Install a momentary on/off button/switch onto CN6, pin 9 and
10. See image above.
(6). Press the power button to start NANO830/831.
4
9418K830000E
©Copyright 2012 Axiomtek Co., Ltd.
Version A1 December 2012
Printed in Taiwan
Connector
Description
CN1
CN2
CN3
CN4
CN5
CN6
CN7
CN8
CN9
CN10
CN11
CN12
CN13
CN14
CN16
CN17
CN18
CN19
SATA1
SSCFAST1
SDIMM1
Digital I/O Port
COM2 Connector (NANO830 only)
COM1 Connector
LVDS Connector
Inverter Connector
Front Panel Connector
PCI-Express Mini Card Connector
Power Output Connector
CPU Fan Connector
SMBus Connector
USB Port 4 and 5 Connector
Ethernet Port 1, USB Port 0 and 1 Stack
Ethernet Port 2, USB Port 2 and 3 Stack
VGA Connector
Audio Jack
DC Jack Power Connector
DisplayPort Connector (NANO830 only)
COM2 Connector (NANO831 only)
Serial ATA Connector
TM
CFast Socket
DDR3 SO-DIMM Connector
9418K830000E
©Copyright 2012 Axiomtek Co., Ltd.
Version A1 December 2012
Printed in Taiwan
1
NANO830/831 Intel® AtomTM D2550/N2600 Processor Nano-ITX Board
Checklist
Jumper Settings
Before applying power to the NANO830/831, please make sure all of the
jumpers are in factory default position.
Jumper
Description
Setting
JP1
LVDS Voltage Selection
Default: +3.3V level
1-2 Close
COM1 RS-232/422/485 Mode Setting
Default: RS-232
3-5, 4-6 Close
JP2
JP3
3-5, 4-6 Close
JP4
JP5
JP6
JP8
JP9
JP10
1-2 Close
COM2 Data/Power Selection
(NANO830 only)
Default: RS-232 Data
COM2 Data/Power Selection
(NANO831 only)
Default: RS-232 Data
COM1 Data/Power Selection
Default: RS-232 Data
CN2 Pin 1: DCD
3-5 Close
CN2 Pin 8: RI
4-6 Close
CN19 Pin 1: DCD
3-5 Close
CN19 Pin 9: RI
4-6 Close
CN3 Pin 1: DCD
3-5 Close
CN3 Pin 8: RI
4-6 Close
LVDS Brightness Control Mode Setting
Default: PWM Mode
Restore BIOS Optimal Defaults
Default: Normal Operation
Auto Power On
Default: Disable
1-2 Close
1-2 Close
Close
Top View
Board Layout
NANO830 – Side View
NANO830
NANO831
Side View
Side View
NANO831 – Side View
2
9418K830000E
©Copyright 2012 Axiomtek Co., Ltd.
Version A1 December 2012
Printed in Taiwan
9418K830000E
©Copyright 2012 Axiomtek Co., Ltd.
Version A1 December 2012
Printed in Taiwan
3