DATASHEET

HA-5104/883
®
Low Noise, High Performance,
Quad Operational Amplifier
April 2002
Features
Description
• This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of
Paragraph 1.2.1.
Low noise and high performance are key words describing
the unity gain stable HA-5104/883. This general purpose
quad amplifier offers an array of dynamic specifications
including 1V/µs slew rate (min), and 8MHz bandwidth (typ).
Complementing these outstanding parameters are very low
noise specifications of 4.3nV/√Hz at 1kHz (typ) or 6nV/√Hz
(max).
• Low Input Noise Voltage Density at 1kHz . 6nV/√Hz (Max)
4.3nV/√Hz (Typ)
• Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . .1V/µs (Min)
3V/µs (Typ)
Fabricated using the Intersil standard high frequency D.I.
process, these operational amplifiers also offer excellent
input specifications such as 2.5mV (max) offset voltage and
75nA (max) offset current. Complementing these specifications are 100dB (min) open loop gain and 55dB channel separation (min). Economically, the HA-5104/883 also
consumes a very moderate amount of power (225mW per
package) while also saving board space and cost.
• Unity Gain Bandwidth . . . . . . . . . . . . . . . . . 8MHz (Typ)
• High Open Loop Gain (Full Temp) . . . . . 100kV/V (Min)
250kV/V (Typ)
• High CMRR, PSRR (Full Temp). . . . . . . . . . . 86dB (Min)
100dB
(Typ)
• Low Offset Voltage Drift . . . . . . . . . . . . . . 3µV/oC (Typ)
• Standard Quad Pinout
This impressive combination of features make this amplifier
ideally suited for designs ranging from audio amplifiers and
active filters to the most demanding signal conditioning and
instrumentation circuits.
Applications
Ordering Information
• No Crossover Distortion
• High Q Active Filters
PART
NUMBER
• Audio Amplifiers
• Integrators
HA1-5104/883
TEMPERATURE
RANGE
-55oC to +125oC
PACKAGE
14 Lead CerDIP
• Signal Generators
• Instrumentation Amplifiers
Pinout
HA-5104/883
(CERDIP)
TOP VIEW
OUT 1
1
-IN1
2
+IN1
3
V+
4
+IN2
5
-IN2
6
OUT 2
7
14 OUT 4
-1
+
4+
13 -IN4
12 +IN4
11 V-
+
3-
+2
-
10 +IN3
9
-IN3
8
OUT 3
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2002. All Rights Reserved
1
Spec Number
511014-883
FN3710.1
HA5104/883
Absolute Maximum Ratings
Thermal Information
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 40V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VPeak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite
(One Amplifier Shorted to Ground)
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC
ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V
Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300oC
Thermal Resistance
θJA
θJC
CerDIP Package . . . . . . . . . . . . . . . . . . .
75oC/W
20oC/W
Package Power Dissipation Limit at +75oC for TJ ≤ +175oC
CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.33W
Package Power Dissipation Derating Factor Above +75oC
CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3mW/oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief
TB379 for details.
Operating Conditions
VINCM ≤ 1/2 (V+ - V-)
RL ≥ 2kΩ
Operating Temperature Range. . . . . . . . . . . . . . . . -55oC to +125oC
Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . ±5V to ±15V
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified.
PARAMETERS
Input Offset Voltage
SYMBOL
VIO
CONDITIONS
GROUP A
SUBGROUPS
VCM = 0V
1
2, 3
Input Bias Current
+IB
-IB
Input Offset Current
Common Mode Range
IIO
+CMR
-CMR
1
VCM = 0V,
+RS = 10kΩ,
-RS = 100Ω
VCM = 0V,
+RS = 100Ω,
-RS = 10kΩ
VCM = 0V,
+RS = 10kΩ,
-RS = 10kΩ
V+ = +3V, V- = -27V
V+ = +27V, V- = -3V
+AVOL
-AVOL
Common Mode
Rejection Ratio
+CMRR
-CMRR
-55oC
o
+25 C
o
o
UNITS
-2.5
2.5
mV
-3.0
3.0
mV
-200
200
nA
nA
1
+25oC
-200
200
nA
o
o
2, 3
+125 C, -55 C
-325
325
nA
1
+25oC
-75
75
nA
o
o
2, 3
+125 C, -55 C
-125
125
nA
1
+25oC
+12
-
V
o
o
2, 3
+125 C, -55 C
+12
-
V
1
+25oC
-
-12
V
-
-12
V
100
-
kV/V
100
-
kV/V
100
-
kV/V
100
-
kV/V
86
-
dB
5, 6
1
∆VCM = -5V,
V+ = +20V, V- = -10V,
VOUT = +5V
+125oC,
MAX
325
4
∆VCM = +5V,
V+ = +10V, V- = -20V,
VOUT = -5V
+25 C
MIN
-325
5, 6
VOUT = 0V and -10V,
RL = 2kΩ
o
+125 C, -55 C
4
VOUT = 0V and +10V,
RL = 2kΩ
TEMPERATURE
2, 3
2, 3
Large Signal Voltage
Gain
LIMITS
o
o
+125 C, -55 C
o
+25 C
+125oC,
-55oC
o
+25 C
o
o
+125 C, -55 C
o
+25 C
o
o
2, 3
+125 C, -55 C
86
-
dB
1
+25oC
86
-
dB
86
-
dB
2, 3
o
o
+125 C, -55 C
Spec Number
2
511014-883
HA5104/883
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)
Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified.
PARAMETERS
Output Voltage Swing
SYMBOL
+VOUT1
-VOUT1
+VOUT2
-VOUT2
Output Current
+IOUT
-IOUT
Quiescent Power Supply
Current
+ICC
-ICC
Power Supply
Rejection Ratio
+PSRR
-PSRR
CONDITIONS
LIMITS
GROUP A
SUBGROUPS
TEMPERATURE
MIN
MAX
UNITS
1
+25oC
10
-
V
2, 3
+125oC, -55oC
10
-
V
1
+25oC
-
-10
V
2, 3
+125oC, -55oC
-
-10
V
1
+25oC
12
-
V
2, 3
+125oC, -55oC
12
-
V
1
+25oC
-
-12
V
2, 3
+125oC, -55oC
-
-12
V
1
+25oC
10
-
mA
2, 3
+125oC, -55oC
10
-
mA
1
+25oC
-
-10
mA
2, 3
+125oC, -55oC
-
-10
mA
1
+25oC
-
6.5
mA
2, 3
+125oC, -55oC
-
7.5
mA
1
+25oC
-6.5
-
mA
2, 3
+125oC, -55oC
-7.5
-
mA
1
+25oC
86
-
dB
2, 3
+125oC, -55oC
86
-
dB
1
+25oC
86
-
dB
2, 3
+125oC, -55oC
86
-
dB
RL = 2kΩ
RL = 2kΩ
RL = 10kΩ
RL = 10kΩ
VOUT = -5V
VOUT = +5V
VOUT = 0V, IOUT = 0mA
VOUT = 0V, IOUT = 0mA
∆VSUP = 10V,
V+ = +10V, V- = -15V
V+ = +20V, V- = -15V
∆VSUP = 10V,
V+ = +15V, V- = -10V
V+ = +15V, V- = -20V
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: VSUPPLY = ±15V, RSOURCE = 50Ω, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = +1V/V, Unless Otherwise Specified.
PARAMETERS
Slew Rate
SYMBOL
+SR
-SR
Rise and Fall Time
Overshoot
CONDITIONS
LIMITS
GROUP A
SUBGROUPS
TEMPERATURE
MIN
MAX
UNITS
4
+25oC
VOUT = -3V to +3V
VOUT = +3V to -3V
4
1
-
V/µs
o
1
-
V/µs
o
+25 C
TR
VOUT = 0 to +200mV
10% ≤ TR ≤ 90%
4
+25 C
-
200
ns
TF
VOUT = 0 to -200mV
10% ≤ TF ≤ 90%
4
+25oC
-
200
ns
+OS
VOUT = 0 to +200mV
4
+25oC
-
35
%
-
35
%
-OS
VOUT = 0 to -200mV
4
o
+25 C
Spec Number
3
511014-883
HA5104/883
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Characterized at: VSUPPLY = ±15V, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = 1V/V, Unless Otherwise Specified.
LIMITS
PARAMETERS
SYMBOL
CONDITIONS
NOTES
TEMPERATURE
MIN
MAX
UNITS
Differential Input
Resistance
RIN
VCM = 0V
1
+25oC
250
-
kΩ
Input Noise Voltage
Density
EN
RS = 20Ω,
fO = 1000Hz
1
+25oC
-
6
nV/√Hz
Input Noise Current
Density
IN
RS = 2MΩ,
fO = 1000Hz
1
+25oC
-
3
pA/√Hz
Full Power
Bandwidth
FPBW
VPEAK = 10V
1, 2
+25oC
32
-
kHz
Minimum Closed Loop
Stable Gain
CLSG
RL = 2kΩ, CL = 50pF
1
-55oC to +125oC
+1
-
V/V
Output Resistance
ROUT
Open Loop
1
+25oC
-
270
Ω
Quiescent Power
Consumption
PC
VOUT = 0V, IOUT =
0mA
Channel Separation
CS
RS = 1kΩ,
AVCL = 100V/V,
VIN = 100mVPEAK at
10kHz Referred to
Input
o
o
1, 3
-55 C to +125 C
-
225
mW
1
+25oC
55
-
dB
NOTES:
1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation.
2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2πVPEAK).
3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.).
TABLE 4. ELECTRICAL TEST REQUIREMENTS
MIL-STD-883 TEST REQUIREMENTS
SUBGROUPS (SEE TABLES 1 AND 2)
Interim Electrical Parameters (Pre Burn-In)
1
Final Electrical Test Parameters
1 (Note 1), 2, 3, 4, 5, 6
Group A Test Requirements
1, 2, 3, 4, 5, 6
Groups C and D Endpoints
1
NOTE:
1. PDA applies to Subgroup 1 only.
Spec Number
4
511014-883
HA5104/883
Die Characteristics
DIE DIMENSIONS:
95 x 99 x 19 mils ± 1 mils
2420 x 2530 x 483µm ± 25.4µm
METALLIZATION:
Type: Al, 1% Cu
Thickness: 16kÅ ± 2kÅ
GLASSIVATION:
Type: Nitride (Si3N4) over Silox (SIO2, 5% Phos.)
Silox Thickness: 12kÅ ± 2kÅ
Nitride Thickness: 3.5kÅ ± 1.5kÅ
WORST CASE CURRENT DENSITY:
1.43 x 105 A/cm2
SUBSTRATE POTENTIAL (Powered Up):
Unbiased
TRANSISTOR COUNT: 175
PROCESS: Bipolar Dielectric Isolation
Metallization Mask Layout
HA5104/883
+IN2
V+
+IN1
-IN1
-IN2
OUT2
OUT1
OUT3
OUT4
-IN3
-IN4
+IN3
V-
+IN4
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
Spec Number
5
511014-883