HA-5104/883 ® Low Noise, High Performance, Quad Operational Amplifier April 2002 Features Description • This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. Low noise and high performance are key words describing the unity gain stable HA-5104/883. This general purpose quad amplifier offers an array of dynamic specifications including 1V/µs slew rate (min), and 8MHz bandwidth (typ). Complementing these outstanding parameters are very low noise specifications of 4.3nV/√Hz at 1kHz (typ) or 6nV/√Hz (max). • Low Input Noise Voltage Density at 1kHz . 6nV/√Hz (Max) 4.3nV/√Hz (Typ) • Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . .1V/µs (Min) 3V/µs (Typ) Fabricated using the Intersil standard high frequency D.I. process, these operational amplifiers also offer excellent input specifications such as 2.5mV (max) offset voltage and 75nA (max) offset current. Complementing these specifications are 100dB (min) open loop gain and 55dB channel separation (min). Economically, the HA-5104/883 also consumes a very moderate amount of power (225mW per package) while also saving board space and cost. • Unity Gain Bandwidth . . . . . . . . . . . . . . . . . 8MHz (Typ) • High Open Loop Gain (Full Temp) . . . . . 100kV/V (Min) 250kV/V (Typ) • High CMRR, PSRR (Full Temp). . . . . . . . . . . 86dB (Min) 100dB (Typ) • Low Offset Voltage Drift . . . . . . . . . . . . . . 3µV/oC (Typ) • Standard Quad Pinout This impressive combination of features make this amplifier ideally suited for designs ranging from audio amplifiers and active filters to the most demanding signal conditioning and instrumentation circuits. Applications Ordering Information • No Crossover Distortion • High Q Active Filters PART NUMBER • Audio Amplifiers • Integrators HA1-5104/883 TEMPERATURE RANGE -55oC to +125oC PACKAGE 14 Lead CerDIP • Signal Generators • Instrumentation Amplifiers Pinout HA-5104/883 (CERDIP) TOP VIEW OUT 1 1 -IN1 2 +IN1 3 V+ 4 +IN2 5 -IN2 6 OUT 2 7 14 OUT 4 -1 + 4+ 13 -IN4 12 +IN4 11 V- + 3- +2 - 10 +IN3 9 -IN3 8 OUT 3 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved 1 Spec Number 511014-883 FN3710.1 HA5104/883 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 40V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VPeak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite (One Amplifier Shorted to Ground) Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300oC Thermal Resistance θJA θJC CerDIP Package . . . . . . . . . . . . . . . . . . . 75oC/W 20oC/W Package Power Dissipation Limit at +75oC for TJ ≤ +175oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.33W Package Power Dissipation Derating Factor Above +75oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3mW/oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Operating Conditions VINCM ≤ 1/2 (V+ - V-) RL ≥ 2kΩ Operating Temperature Range. . . . . . . . . . . . . . . . -55oC to +125oC Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . ±5V to ±15V TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified. PARAMETERS Input Offset Voltage SYMBOL VIO CONDITIONS GROUP A SUBGROUPS VCM = 0V 1 2, 3 Input Bias Current +IB -IB Input Offset Current Common Mode Range IIO +CMR -CMR 1 VCM = 0V, +RS = 10kΩ, -RS = 100Ω VCM = 0V, +RS = 100Ω, -RS = 10kΩ VCM = 0V, +RS = 10kΩ, -RS = 10kΩ V+ = +3V, V- = -27V V+ = +27V, V- = -3V +AVOL -AVOL Common Mode Rejection Ratio +CMRR -CMRR -55oC o +25 C o o UNITS -2.5 2.5 mV -3.0 3.0 mV -200 200 nA nA 1 +25oC -200 200 nA o o 2, 3 +125 C, -55 C -325 325 nA 1 +25oC -75 75 nA o o 2, 3 +125 C, -55 C -125 125 nA 1 +25oC +12 - V o o 2, 3 +125 C, -55 C +12 - V 1 +25oC - -12 V - -12 V 100 - kV/V 100 - kV/V 100 - kV/V 100 - kV/V 86 - dB 5, 6 1 ∆VCM = -5V, V+ = +20V, V- = -10V, VOUT = +5V +125oC, MAX 325 4 ∆VCM = +5V, V+ = +10V, V- = -20V, VOUT = -5V +25 C MIN -325 5, 6 VOUT = 0V and -10V, RL = 2kΩ o +125 C, -55 C 4 VOUT = 0V and +10V, RL = 2kΩ TEMPERATURE 2, 3 2, 3 Large Signal Voltage Gain LIMITS o o +125 C, -55 C o +25 C +125oC, -55oC o +25 C o o +125 C, -55 C o +25 C o o 2, 3 +125 C, -55 C 86 - dB 1 +25oC 86 - dB 86 - dB 2, 3 o o +125 C, -55 C Spec Number 2 511014-883 HA5104/883 TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified. PARAMETERS Output Voltage Swing SYMBOL +VOUT1 -VOUT1 +VOUT2 -VOUT2 Output Current +IOUT -IOUT Quiescent Power Supply Current +ICC -ICC Power Supply Rejection Ratio +PSRR -PSRR CONDITIONS LIMITS GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 1 +25oC 10 - V 2, 3 +125oC, -55oC 10 - V 1 +25oC - -10 V 2, 3 +125oC, -55oC - -10 V 1 +25oC 12 - V 2, 3 +125oC, -55oC 12 - V 1 +25oC - -12 V 2, 3 +125oC, -55oC - -12 V 1 +25oC 10 - mA 2, 3 +125oC, -55oC 10 - mA 1 +25oC - -10 mA 2, 3 +125oC, -55oC - -10 mA 1 +25oC - 6.5 mA 2, 3 +125oC, -55oC - 7.5 mA 1 +25oC -6.5 - mA 2, 3 +125oC, -55oC -7.5 - mA 1 +25oC 86 - dB 2, 3 +125oC, -55oC 86 - dB 1 +25oC 86 - dB 2, 3 +125oC, -55oC 86 - dB RL = 2kΩ RL = 2kΩ RL = 10kΩ RL = 10kΩ VOUT = -5V VOUT = +5V VOUT = 0V, IOUT = 0mA VOUT = 0V, IOUT = 0mA ∆VSUP = 10V, V+ = +10V, V- = -15V V+ = +20V, V- = -15V ∆VSUP = 10V, V+ = +15V, V- = -10V V+ = +15V, V- = -20V TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = ±15V, RSOURCE = 50Ω, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = +1V/V, Unless Otherwise Specified. PARAMETERS Slew Rate SYMBOL +SR -SR Rise and Fall Time Overshoot CONDITIONS LIMITS GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 4 +25oC VOUT = -3V to +3V VOUT = +3V to -3V 4 1 - V/µs o 1 - V/µs o +25 C TR VOUT = 0 to +200mV 10% ≤ TR ≤ 90% 4 +25 C - 200 ns TF VOUT = 0 to -200mV 10% ≤ TF ≤ 90% 4 +25oC - 200 ns +OS VOUT = 0 to +200mV 4 +25oC - 35 % - 35 % -OS VOUT = 0 to -200mV 4 o +25 C Spec Number 3 511014-883 HA5104/883 TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS Device Characterized at: VSUPPLY = ±15V, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = 1V/V, Unless Otherwise Specified. LIMITS PARAMETERS SYMBOL CONDITIONS NOTES TEMPERATURE MIN MAX UNITS Differential Input Resistance RIN VCM = 0V 1 +25oC 250 - kΩ Input Noise Voltage Density EN RS = 20Ω, fO = 1000Hz 1 +25oC - 6 nV/√Hz Input Noise Current Density IN RS = 2MΩ, fO = 1000Hz 1 +25oC - 3 pA/√Hz Full Power Bandwidth FPBW VPEAK = 10V 1, 2 +25oC 32 - kHz Minimum Closed Loop Stable Gain CLSG RL = 2kΩ, CL = 50pF 1 -55oC to +125oC +1 - V/V Output Resistance ROUT Open Loop 1 +25oC - 270 Ω Quiescent Power Consumption PC VOUT = 0V, IOUT = 0mA Channel Separation CS RS = 1kΩ, AVCL = 100V/V, VIN = 100mVPEAK at 10kHz Referred to Input o o 1, 3 -55 C to +125 C - 225 mW 1 +25oC 55 - dB NOTES: 1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. 2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2πVPEAK). 3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.). TABLE 4. ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS SUBGROUPS (SEE TABLES 1 AND 2) Interim Electrical Parameters (Pre Burn-In) 1 Final Electrical Test Parameters 1 (Note 1), 2, 3, 4, 5, 6 Group A Test Requirements 1, 2, 3, 4, 5, 6 Groups C and D Endpoints 1 NOTE: 1. PDA applies to Subgroup 1 only. Spec Number 4 511014-883 HA5104/883 Die Characteristics DIE DIMENSIONS: 95 x 99 x 19 mils ± 1 mils 2420 x 2530 x 483µm ± 25.4µm METALLIZATION: Type: Al, 1% Cu Thickness: 16kÅ ± 2kÅ GLASSIVATION: Type: Nitride (Si3N4) over Silox (SIO2, 5% Phos.) Silox Thickness: 12kÅ ± 2kÅ Nitride Thickness: 3.5kÅ ± 1.5kÅ WORST CASE CURRENT DENSITY: 1.43 x 105 A/cm2 SUBSTRATE POTENTIAL (Powered Up): Unbiased TRANSISTOR COUNT: 175 PROCESS: Bipolar Dielectric Isolation Metallization Mask Layout HA5104/883 +IN2 V+ +IN1 -IN1 -IN2 OUT2 OUT1 OUT3 OUT4 -IN3 -IN4 +IN3 V- +IN4 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com Spec Number 5 511014-883