EL7501 T UCT ROD ACEMEN at P E r T L e E P t L n E e O R OBS ENDED upport C om/tsc c . M sil al S OM ECData hnic ww.inter Sheet January 1996, Rev B NO R t o r Tec w u r IL o ac S t n R o E c 8-INT 1-88 ® 100V High Side Driver Features The EL7501 provides a low cost solution to many high side drive applications. The EL7501 is DC coupled so there are no start up problems associated with AC coupled schemes. The EL7501 is driven by user supplied complementary signals. • 100V High Side Voltage FN7289 • Rail to Rail Output • 1MHz Operation • 1.0A Peak Current • Matched Rise and Fall Times Pinout • Direct Coupled • No Start Up Ambiguity Applications • Uninterruptible Power Supplies • DC-DC Converters • Motor Control • Power MOSFET Driver Ordering Information PART NUMBER TEMP. RANGE PACKAGE PKG. NO. EL7501CN -40°C to +85°C 8-Pin PDIP MDP0031 EL7501CS -40°C to +85°C 8-Pin SO MDP0027 7501 Waveform Example 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2003. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc. All other trademarks mentioned are the property of their respective owners. EL7501 Absolute Maximum Ratings (TA = 25°C) Supply (VDD or LX to R- or R+) . . . . . . . . . . . . . . . . . . . . . . . . .100V Supply (VDD to LX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5V Output Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V below GND, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+0.3V above VDD Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2A Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125°C Power Dissipation SOIC . . . . . . . . . . . . . . . . . . . . . . . .570mW PDIP. . . . . . . . . . . . . . . . . . . . . . . .1050mW CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA DC Electrical Specifications TA = 25°C, VDD = 15V, CLOAD = 1000pF, unless otherwise specified. PARAMETER Input/Output Power Supply DESCRIPTION VDIFF (Min) Minimum Differential Input Signal to Switch Output IDS OFF Output Leakage GND < VOUT < VDD ROH Pull-up Resistance ROL Pull-down Resistance IPK Peak Output Current IDC Continuous Output Current Source/Sink IDD Supply Current into VDD VDD Operating Voltage AC Electrical Specifications PARAMETER Switching Characteristics TEST CONDITIONS tR tF MIN. TYP. MAX. 1.0 -10.0 UNITS V 0.2 +10.0 µA IOUT = -100mA 5.0 10.0 Ω IOUT = +100mA 5.0 10.0 Ω 1.0 A 50.0 mA 4.5 4.0 mA 15.0 V TA = 25°C, VDD = 15V, CLOAD = 1000pF, unless otherwise specified. DESCRIPTION Rise Time Fall Time TEST CONDITIONS MIN. TYP. MAX. CL = 500pF CL = 1000pF 15.0 20.0 40.0 CL = 500pF CL = 1000pF 15.0 20.0 40.0 UNITS ns ns tD OFF Turn Off Delay Time 90.0 140.0 ns tD ON Turn On Delay Time 90.0 140.0 ns 2 EL7501 FIGURE 1. EL7501 TEST CIRCUIT FIGURE 2. EL7501 ALTERNATE DRIVE METHOD 3 EL7501 Typical Performance Curves Quiescent Supply Current vs Supply Voltage Output Rising Edge Delay Time vs Supply Voltage and Drive Voltage 4 Average Supply Current vs Voltage and Frequency Output Falling Edge Delay Time vs Supply Voltage and Drive Voltage Supply Current vs DC Offset Voltage and VDD Delay Time vs Temperature and Supply Voltage EL7501 Typical Performance Curves (Continued) Max. Power/ Derating Curves 8-Pin Package Input Threshold vs Supply Voltage Input Current vs Input Voltage Enable Threshold vs Supply Voltage Peak Drive vs Supply Voltage “On” Resistance vs Supply Voltage Rise/Fall Time vs Load and Supply Rise/Fall Time vs Temperature All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 5