ISL9016 ® Data Sheet January 22, 2009 150mA Dual LDO with Low Noise, High PSRR, and Low IQ ISL9016 is a high performance dual LDO capable of providing up to 150mA current on each channel. It features a low standby current and very high PSRR and is stable with output capacitance of 1µF to 4.7µF with an ESR of up to 200mΩ. The device integrates a separate enable function for each output. The quiescent current is typically 49µA when only one LDO is enabled and typically 80µA when both LDOs are enabled. When both LDOs are under shutdown condition, the drawing current is typically less than 1µA. FN6832.0 Features • Dual Integrated 150mA High Performance LDOs • High PSRR: 80dB @ 1kHz and 45dB @ 1MHz • Reverse Current Protection • Low Quiescent Current - 49µA (Single LDO Enabled)/80µA (Dual LDOs Enabled) • Excellent Load Transient Response • Typically ±0.8% Output Voltage Accuracy • Low Output Noise: Typically 25µVRMS ISL9016 provides a wide input voltage range from 1.8V to 6.5V. It also has a high PSRR of 80dB at 1kHz and 45dB at 1MHz. ISL9016 also provides output current limit, overheat protection, reverse current protection, as well as excellent load transient response. • Wide Input Voltage Capability: 1.8V to 6.5V ISL9016 is offered in a tiny 1.6mmx1.6mm 6 Ld µTDFN package. Output voltage options are available from 1.2V to 3.3V. Several combinations of voltage outputs are standard and others may be available upon request. • Soft-start to Limit Input Current Surge During Enable Pinout • Pb-free (RoHS Compliant) • Low Dropout Voltage: Typically 120mV @ 150mA • Separate Enable Control for each LDO • Stable with 1µF to 4.7µF Ceramic Output Capacitors • Current Limit and Overheat Protection • Tiny 6 Ld 1.6mmx1.6mm µTDFN package ISL9016 (6 LD 1.6x1.6 µTDFN) TOP VIEW Applications VIN 1 6 VOUT1 • Portable Instruments, MP3/4 Players, PMP, DSC GND 2 5 VOUT2 • Handheld Devices including Medical Handhelds EN2 3 4 EN1 1 • PDAs, Cell Phones and Smart Phones CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2009. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. ISL9016 Ordering Information PART NUMBER (Notes 1, 3) PART MARKING VO1 VOLTAGE (V) (Note 2) VO2 VOLTAGE (V) (Note 2) TEMP RANGE (°C) PACKAGE (Pb-Free) PKG DWG. # ISL9016IRUWCZ-T N7 1.2 1.8 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUWGZ-T N6 1.2 2.7 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUWJZ-T N2 1.2 2.8 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUWKZ-T N1 1.2 2.85 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUBWZ-T R7 1.5 1.2 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUBBZ-T R6 1.5 1.5 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUCWZ-T R5 1.8 1.2 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUCBZ-T R4 1.8 1.5 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUFWZ-T R3 2.5 1.2 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUFBZ-T N8 2.5 1.5 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUFCZ-T N9 2.5 1.8 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUFFZ-T P0 2.5 2.5 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUGWZ-T P1 2.7 1.2 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUGCZ-T R2 2.7 1.8 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUGGZ-T N3 2.7 2.7 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUJWZ-T P2 2.8 1.2 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUJBZ-T P3 2.8 1.5 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUJCZ-T N4 2.8 1.8 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUJJZ-T N0 2.8 2.8 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUKWZ-T P5 2.85 1.2 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUKFZ-T P4 2.85 2.5 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUKKZ-T N5 2.85 2.85 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUMWZ-T P6 3.0 1.2 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUMBZ-T P7 3.0 1.5 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUMCZ-T P8 3.0 1.8 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUMKZ-T P9 3.0 2.85 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUNWZ-T R0 3.3 1.2 -40 to +85 6 Ld µTDFN L6.1.6x1.6A ISL9016IRUNCZ-T R1 3.3 1.8 -40 to +85 6 Ld µTDFN L6.1.6x1.6A NOTES: 1. Please refer to TB347 for details on reel specifications. 2. For other output voltages, contact Intersil marketing or local sales office. 3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2 FN6832.0 January 22, 2009 ISL9016 Absolute Maximum Ratings Thermal Information VIN to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +7.1V All Other Pins to GND . . . . . . . . . . . . . . . . . . . . -0.3 to (VIN + 0.3)V Thermal Resistance Recommended Operating Conditions Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8V to 6.5V Each LDO Load Current . . . . . . . . . . . . . . . . . . . . . . . .up to 150mA Ambient Temperature Range (TA) . . . . . . . . . . . . . . .-40°C to +85°C θJA (°C/W) 6 Ld μTDFN Package (Note 4) . . . . . . . . . . . . . . . 117.5 Junction Temperature Range . . . . . . . . . . . . . . . . .-40°C to +125°C Operating Temperature Range . . . . . . . . . . . . . . . . .-40°C to +85°C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTE: 4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. Electrical Specifications Unless otherwise noted, all parameter limits are guaranteed over the recommended operating conditions and the typical specifications are measured at the following conditions: TA = +25°C; VIN = (VO + 0.5V) to 6.5V with a minimum VIN of 1.8V; CIN = 1µF; CO = 1µF. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS 6.5 V 1.710 1.775 V DC CHARACTERISTICS Supply Voltage VIN UVLO Threshold 1.8 VUV+ VUV- 1.55 1.62 Quiescent condition: IO1 = 0µA; IO2 = 0µA Input Quiescent Current Shutdown Current IDD1 One LDO active 49 67 µA IDD2 Both LDO active 80 100 µA IDDS @ +25°C 0.1 1.0 µA Regulation Voltage Accuracy Maximum Output Current IMAX Internal Current Limit ILIM Dropout Voltage (Note 5) Thermal Shutdown Temperature VIN = VO + 0.5V to 6.5V, IO = 10µA to 150mA, TA = +25°C -0.8 +0.8 % VIN = VO + 0.5V to 6.5V, IO = 10µA to 150mA, TA = -40°C to +85°C -1.8 +1.8 % Each LDO, Continuous 150 175 mA 265 355 mA 250 425 mV VDO1 IO = 150mA; 1.2V ≤ VO ≤ 2.1V VDO2 IO = 150mA; 2.1V ≤ VO ≤ 2.8V 200 325 mV VDO3 IO = 150mA; 2.8V ≤ VO 120 200 mV TSD+ 145 °C TSD- 110 °C @ 1kHz 80 dB @ 10kHz 60 dB @ 100kHz 50 dB @ 1MHz 45 dB VIN = 4.2V, IO = 10mA, TA = +25°C, BW = 10Hz to 100kHz 25 µVRMS Time from assertion of the ENx pin to when the output voltage reaches 95% of the VO(nom) 400 AC CHARACTERISTICS IO = 10mA, VIN = 3.7V(min), VO = 2.7V, TA = +25°C Ripple Rejection Output Noise Voltage DEVICE START-UP CHARACTERISTICS Device Enable Time tEN 3 600 µs FN6832.0 January 22, 2009 ISL9016 Electrical Specifications Unless otherwise noted, all parameter limits are guaranteed over the recommended operating conditions and the typical specifications are measured at the following conditions: TA = +25°C; VIN = (VO + 0.5V) to 6.5V with a minimum VIN of 1.8V; CIN = 1µF; CO = 1µF. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. (Continued) PARAMETER SYMBOL LDO Soft-Start Ramp Rate tSSR TEST CONDITIONS MIN TYP MAX UNITS 30 60 µs/V -0.3 0.4 V 1.1 VIN + 0.3 V 0.1 µA 15 µA Slope of linear portion of LDO output voltage ramp during start-up EN PIN CHARACTERISTICS Input Low Voltage VIL Input High Voltage VIH Input Leakage Current TA = -20°C to +85° IIL, IIH REVERSE CURRENT CHARACTERISTICS Output Reverse Leakage Current (Note 6) IORLC VIN = 0V, VOUT = 5.5V 8 NOTES: 5. VOx = 0.98*VOx(NOM); Valid for VOx greater than 1.80V. 6. Output reverse leakage current is measured with VIN pin grounded and VOUT pin connected to 5.5V. 4 FN6832.0 January 22, 2009 ISL9016 Typical Operating Performance 55 55 50 QUIESCENT CURRENT (µA) QUIESCENT CURRENT (µA) T = +85°C T = +85°C T = +50°C T = +25°C 45 40 T = 0°C 35 T = -25°C T = +50°C 50 T = +25°C 45 40 T = 0°C 35 T = -25°C T = -40°C T = -40°C 30 2.4 3.6 4.8 30 2.4 6.0 FIGURE 1. QUIESCENT CURRENT vs INPUT VOLTAGE (VOUT1 = 2.1V, ONLY LDO1 ENABLED) 6.0 FIGURE 2. QUIESCENT CURRENT vs INPUT VOLTAGE (VOUT2 = 2.1V, ONLY LDO2 ENABLED) T = +85°C QUIESCENT CURRENT (µA) QUIESCENT CURRENT (µA) 4.8 55 85 T = +50°C 80 T = +25°C 75 70 T = 0°C 65 T = -25°C T = +25°C 60 2.4 3.6 T = +50°C T = +85°C 50 45 40 T = 0°C T = -25°C 35 T = -40°C T = -40°C 4.8 30 3.6 6.0 4.4 5.2 6.0 INPUT VOLTAGE (V) INPUT VOLTAGE (V) FIGURE 4. QUIESCENT CURRENT vs INPUT VOLTAGE (VOUT1 = 3.3V, ONLY LDO1 ENABLED) FIGURE 3. QUIESCENT CURRENT vs INPUT VOLTAGE (VOUT1 = VOUT2 = 2.1V, LDO1 AND LDO2 ENABLED) 55 85 T = +25°C T = +50°C T = +85°C QUIESCENT CURRENT (µA) QUIESCENT CURRENT (µA) 3.6 INPUT VOLTAGE (V) INPUT VOLTAGE (V) 50 45 40 T = 0°C T = -25°C 35 T = +25°C 80 T = +85°C T = +50°C 75 T = 0°C 70 T = -25°C 65 T = -40°C T = -40°C 60 30 3.6 4.4 5.2 INPUT VOLTAGE (V) FIGURE 5. QUIESCENT CURRENT vs INPUT VOLTAGE (VOUT2 = 3.3V, ONLY LDO2 ENABLED) 5 6.0 3.6 4.4 5.2 6.0 INPUT VOLTAGE (V) FIGURE 6. QUIESCENT CURRENT vs INPUT VOLTAGE (VOUT1 = VOUT2 = 3.3V, LDO1 AND LDO2 ENABLED) FN6832.0 January 22, 2009 ISL9016 Typical Operating Performance 10 15 T = +85°C 10 T = +25°C 0 ΔVO (mV) 5 ΔVO (mV) T = +85°C 5 0 -5 T = +25°C -5 -10 T = -40°C -15 -10 T = -40°C -20 -15 1.5 3.0 4.5 1.5 6.0 2.5 4.5 5.5 FIGURE 7. ΔVOUT vs INPUT VOLTAGE (VOUT_NOMINAL = 1.2V, IOUT = 50mA) FIGURE 8. ΔVOUT vs INPUT VOLTAGE (VOUT_NOMINAL = 1.2V, IOUT = 150mA) 1.22 3.32 OUTPUT VOLTAGE (V) 1.21 1.20 T = +25°C 1.19 T = +25°C 3.31 T = +85°C OUTPUT VOLTAGE (V) 3.5 INPUT VOLTAGE (V) INPUT VOLTAGE (V) 3.30 T = +85°C 3.29 3.28 T = -40°C 3.27 3.26 T = -40°C 1.18 3.25 0 30 60 90 120 150 0 30 LOAD CURRENT (mA) FIGURE 9. LOAD REGULATION (VIN = 1.8V, VOUT = 1.2V) EN1 = EN2 120 150 FIGURE 10. LOAD REGULATION (VIN = 4.5V, VOUT = 3.3V) 5V/DIV 5V/DIV 60 90 LOAD CURRENT (mA) VIN VOUT1 (AC COUPLED) 50mV/DIV 1V/DIV VOUT1 50mV/DIV 200mA/DIV 1V/DIV VOUT2 100µs/DIV FIGURE 11. ENABLE OPERATION (VIN = 3.6V, VOUT1 = VOUT1 = 1.2V) 6 VOUT2 (AC COUPLED) IOUT1 1ms/DIV FIGURE 12. LOAD TRANSIENT RESPONSE (VIN = 3.6V, VOUT1 = VOUT2 = 1.2V, IOUT1 0.01mA TO 150mA) FN6832.0 January 22, 2009 ISL9016 Typical Operating Performance 5V/DIV VIN 5V/DIV VIN VOUT1 (AC COUPLED) 50mV/DIV 50mV/DIV VOUT1 (AC COUPLED) 1ms/DIV VOUT2 (AC COUPLED) 50mV/DIV 50mV/DIV IOUT1 VOUT2 (AC COUPLED) IOUT1 200mA/DIV 200mA/DIV 1ms/DIV 1ms/DIV FIGURE 13. LOAD TRANSIENT RESPONSE (VIN = 3.6V, VOUT1 = VOUT2 = 1.2V, IOUT2 0.01mA TO 150mA) FIGURE 14. LOAD TRANSIENT RESPONSE (VIN = 3.6V, VOUT1 = VOUT2 = 3.3V, IOUT1 0.01mA TO 150mA) VOUT1 (AC COUPLED) VOUT (AC COUPLED) 50mV/DIV 100mV/DIV VOUT2 (AC COUPLED) 20mV/DIV IOUT1 IOUT 100mA/DIV 1ms/DIV di/dt = 150mA/µs FIGURE 15. LOAD TRANSIENT RESPONSE (VIN = 1.8V, VOUT1 = VOUT2 = 1.2V, IOUT1 0.01mA TO 150mA) 7 100mA/DIV 1ms/DIV di/dt = 150mA/µs FIGURE 16. LOAD TRANSIENT RESPONSE (VIN = 3.3V, VOUT1 = VOUT2 = 1.2V, IOUT1 0.01mA TO 150mA) FN6832.0 January 22, 2009 ISL9016 Pin Descriptions PIN # PIN NAME 1 VIN Supply Voltage/LDO Input. Connect a 1µF capacitor to GND. 2 GND GND is the connection to system ground. Connect to PCB Ground plane. 3 EN2 LDO2 Enable pin. Enable = High, Disable = Low. A 100k resistor should be connected between EN2 and the control voltage rail. Do NOT leave it floating. 4 EN1 LDO1 Enable pin. Enable = High, Disable = Low. A 100k resistor should be connected between EN1 and the control voltage rail. Do NOT leave it floating. 5 VOUT2 LDO2 Output. Connect capacitor with a value from 1µF to 4.7µF to GND (1µF recommended). 6 VOUT1 LDO1 Output. Connect capacitor with a value from 1µF to 4.7µF to GND (1µF recommended). - E-Pad Connect the e-pad to the system ground. DESCRIPTION Typical Application Diagram ISL9016 VOUT1 1.2V~3.3V, 0~150mA VIN (1.8V TO 6.5V) VIN VOUT1 VOUT2 1.2V~3.3V, 0~150mA C1 R1 GND VOUT2 EN2 EN1 C2 ON OFF ON C3 R2 OFF C1, C2, C3:1µF, X5R (or X7R) CERAMIC CAPACITOR R1, R2: 100k 8 FN6832.0 January 22, 2009 ISL9016 Block Diagram VOUT2 VIN VOUT1 REVERSE CURRENT PROTECTION VIN VOUT1 EN1 UNDERVOLTAGE LOCKOUT EN2 SHORT CIRCUIT THERMAL PROTECTION SOFT-START CONTROL LOGIC EN1 VREF1 + LDO-2 LDO-1 VREF2 VREF1 BANDGAP TEMP-SENSOR VREF3 REFERENCE VOLTAGES GND Functional Description ISL9016 contains two high performance LDO’s. High performance is achieved through a circuit which delivers fast transient response to varying load conditions. In a quiescent condition, the ISL9016 adjusts its biasing to achieve the lowest standby current consumption. The device also integrates current limit protection, thermal shutdown protection, reverse current protection and soft-start. Thermal shutdown protects the device against overheating. Soft-start limits the start-up input current surges. In some certain application circuits, the output voltage may be externally held up, meanwhile, the input voltage could be connected to ground, or connected to some voltage lower than the output side, or be left open circuit. ISL9016 features the reverse current protection; it can limit the current flow from output to input. This protection will automatically initiate when VOUT is detected to be higher than VIN. When VIN is pulled to ground and VOUT is held at 5.5V, the current flow from VOUT to VIN is typically less than 8µA. Enable Control The ISL9016 has two separate enable pins, EN1 and EN2, which independently enable/disable each of the LDO outputs. When both EN1 and EN2 are low, the whole device is in shutdown mode. In this condition, all on-chip circuits are off, and the device draws minimum current, typically less than 0.1mA. When one or both the EN pins go high, the 9 LDO1 and/or LDO2 will be enabled accordingly based on the voltage signal applied on its related EN pin and start from the soft-start. Likewise, when one or both EN pins go low, LDO1 and/or LDO2 will be disabled based on the signal applied on its related EN pin. A 100kΩ (or above) pull-up resistor should be connected between ENx pin and the external control voltage (as shown in the “Typical Application Diagram” on page 8). LDO Protections ISL9016 offers several protections which make it ideal for using in battery-powered application circuits. ISL9016 provides short-circuit protection by limiting the output current to typical 265mA. When short circuit happens, the circuit is limited at 265mA (typical). If the short circuit lasts long enough, the die temperature increases, and the over-temperature protection circuit will turn off the output. When the die temperature reaches about +145°C, the thermal protection starts working. Under the overheat condition, only the LDO sourcing more than 50mA will be shut off. This does not affect the operation of the other LDO. If both LDOs source more than 50mA and an overheat condition occurs, both LDO outputs will be disabled. Once the die temperature falls back to about +110°C, the disabled LDO(s) are re-enabled and soft-start automatically takes place. In certain applications, the following input/output situations may occur: FN6832.0 January 22, 2009 ISL9016 With output voltage externally held up higher than the input voltage: 1. Input is pulled to ground; 2. input is left open circuit; and 3. input is pulled to some intermediate voltage ISL9016 provides the reverse current protection to limit the current flow from output to input under these situations. When input is pulled to ground and output is held to 5.5V, the typical reverse current from output to input side is less than 8µA. Input and Output Capacitors The ISL9016 provides a linear regulator that has low quiescent current, fast transient response, and overall stability across the recommended operating conditions. A ceramic capacitor (X5R or X7R) with a capacitance of 1µF to 4.7µF with an ESR up to 200mΩ is suitable for ISL9016 to maintain its output stability. The ground connection of the output capacitor should be connected directly to the GND pin of the device, and also placed close to the device. Similarly for the input capacitor, usually a 1µF ceramic capacitor (X5R or X7R) is suitable for most cases, but if large, fast rising-time load transient condition is expected, a higher value input capacitor may be necessary to achieve better performance. Board Layout Recommendations A good PCB layout will be an important step to achieve good performance. It is recommended to design the board with separate ground planes for input and output, and connect both ground planes at the GND pin of the device. Consideration should be taken when placing the components and route the trace to minimize the ground impedance, as well as keep the parasitic inductance low. Usually the input/output capacitors should be placed close to the device with good ground connection. 10 FN6832.0 January 22, 2009 ISL9016 Ultra Thin Dual Flat No-Lead Plastic Package (UTDFN) A A E 6 B 6 LEAD ULTRA THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE 4 MILLIMETERS D PIN 1 REFERENCE 2X 0.15 C 1 2X L6.1.6x1.6A 3 MIN NOMINAL MAX NOTES A 0.45 0.50 0.55 - A1 - - 0.05 - A1 TOP VIEW e 1.00 REF 4 6 L CO.2 0.15 0.20 0.25 - D 1.55 1.60 1.65 4 D2 0.40 0.45 0.50 - E 1.55 1.60 1.65 4 E2 0.95 1.00 1.05 - 0.50 BSC e L 3 1 b 6X 0.10 M C A B E2 - b DAP SIZE 1.30 x 0.76 0.25 0.30 0.35 Rev. 1 6/06 NOTES: 1. Dimensions are in mm. Angles in degrees. BOTTOM VIEW DETAIL A 6X 0.127 REF A3 0.15 C D2 SYMBOL 2. Coplanarity applies to the exposed pad as well as the terminals. Coplanarity shall not exceed 0.08mm. 0.10 C 3. Warpage shall not exceed 0.10mm. 0.08 C 4. Package length/package width are considered as special characteristics. 5. JEDEC Reference MO-229. A3 SIDE VIEW C SEATING PLANE 6. For additional information, to assist with the PCB Land Pattern Design effort, see Intersil Technical Brief TB389. 0.127±0.008 0.127 +0.058 -0.008 TERMINAL THICKNESS A1 DETAIL A 0.25 0.50 1.00 0.45 1.00 2.00 0.30 1.25 LAND PATTERN 6 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11 FN6832.0 January 22, 2009