TSOP581.., TSOP583.., TSOP585.. Datasheet

TSOP581.., TSOP583.., TSOP585..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Improved immunity against HF and RF noise
• Low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Improved shielding against EMI
• Supply voltage: 2.5 V to 5.5 V
• Suitable for short bursts: burst length ≥ 6 carrier
cycles
19026
• Improved immunity against ambient light
• Insensitive to supply voltage ripple and noise
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
MECHANICAL DATA
Pinning for TSOP581.., TSOP583.., TSOP585:
DESCRIPTION
1 = OUT, 2 = GND, 3 = VS
These products are miniaturized receivers for infrared
remote control systems. A PIN diode and a preamplifier are
assembled on a lead frame, the epoxy package contains an
IR filter. The demodulated output signal can be directly
connected to a microprocessor for decoding.
The TSOP583.. series devices are optimized to suppress
almost all spurious pulses from Wi-Fi and CFL sources.
They may suppress some data signals if continuously
transmitted.
The TSOP581.. series devices are provided primarily for
compatibility with old AGC1 designs. New designs should
prefer the TSOP583.. series containing the newer AGC3.
The TSOP585.. series are useful to suppress even extreme
levels of optical noise, but may also suppress some data
signals. Please check compatibility with your codes.
These components have not been qualified according to
automotive specifications.
PARTS TABLE
AGC
30 kHz
Carrier
frequency
LEGACY PRODUCT FOR
SHORT BURST REMOTE
CONTROLS (AGC1)
NOISY ENVIRONMENTS AND
SHORT BURSTS (AGC3)
VERY NOISY ENVIRONMENTS
AND SHORT BURSTS (AGC5)
TSOP58130
TSOP58330
TSOP58530
33 kHz
TSOP58133
TSOP58333
TSOP58533
36 kHz
TSOP58136
TSOP58336 (1)
TSOP58536
38 kHz
TSOP58138
TSOP58338 (2)(3)(4)(5)
TSOP58538
40 kHz
TSOP58140
TSOP58340
TSOP58540
56 kHz
TSOP58156
TSOP58356
TSOP58556
Package
Minicast
Pinning
1 = OUT, 2 = GND, 3 = VS
Dimensions (mm)
5.0 W x 6.95 H x 4.8 D
Mounting
Leaded
Application
Best remote control code
Rev. 1.3, 10-Nov-15
Remote control
(1)
MCIR
(2)
Mitsubishi
1
(3)
RECS-80 Code
(4)
r-map
(5)
XMP-1, XMP-2
Document Number: 82462
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP581.., TSOP583.., TSOP585..
www.vishay.com
Vishay Semiconductors
BLOCK DIAGRAM
APPLICATION CIRCUIT
17170-10
16833_14
R1
Transmitter
with
TSALxxxx
3
VS
1
Input
Band
pass
AGC
µC
OUT
Demodulator
VO
GND
GND
The external components R1 and C1 are optional
to improve the robustness against electrical overstress
(typical values are R1 = 100 Ω, C1 = 0.1 µF).
2
PIN
+ VS
C1
Circuit
33 kΩ
IR receiver
Control circuit
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Supply voltage
Supply current
Output voltage
Voltage at output to supply
Output current
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
Soldering temperature
TEST CONDITION
SYMBOL
VS
IS
VO
VS - VO
IO
Tj
Tstg
Tamb
Ptot
Tsd
Tamb ≤ 85 °C
t ≤ 10 s, 1 mm from case
VALUE
-0.3 to +6
5
-0.3 to 5.5
-0.3 to (VS + 0.3)
5
100
-25 to +85
-25 to +85
10
260
UNIT
V
mA
V
V
mA
°C
°C
°C
mW
°C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
Supply voltage
TEST CONDITION
VS = 5 V, Ev = 0
Ev = 40 klx, sunlight
Ev = 0, IR diode TSAL6200, IF = 250 mA,
test signal see Fig. 1
IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1
Pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1
tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1
Angle of half transmission distance
Supply current
Transmission distance
Output voltage low
Minimum irradiance
Maximum irradiance
Directivity
SYMBOL
VS
ISD
ISH
MIN.
2.5
0.55
-
TYP.
0.7
0.8
MAX.
5.5
0.9
-
UNIT
V
mA
mA
d
-
40
-
m
VOSL
-
-
100
mV
Ee min.
-
0.2
0.4
mW/m2
Ee max.
ϕ1/2
50
-
± 45
-
W/m2
deg
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
0.5
Optical Test Signal
(IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms)
tpo - Output Pulse Width (ms)
Ee
t
tpi *)
T
*) tpi ≥ 6/f0 is recommended for optimal function
Output Signal
VO
1)
2)
VOH
VOL
14337
3/f0 < td < 9/f0
tpi - 4/f0 < tpo < tpi + 6/f0
λ = 950 nm,
optical test signal, Fig. 1
0.4
0.3
Output pulse width
0.2
Input burst length
0.1
0
td
1)
tpo
2)
0.1
t
Fig. 1 - Output Active Low
Rev. 1.3, 10-Nov-15
10
1000
100 000
Ee - Irradiance (mW/m2)
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
2
Document Number: 82462
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP581.., TSOP583.., TSOP585..
www.vishay.com
Optical Test Signal
600 µs
t
600 µs
t = 60 ms
94 8134
Output Signal, (see Fig. 4)
VO
VOH
VOL
4.0
3.5
2.5
2.0
1.5
1.0
0.5
0
0.01
Ee min. - Threshold Irradiance (mW/m2)
ton, toff - Output Pulse Width (ms)
0.6
toff
0.4
0.3
0.2
λ = 950 nm,
optical test signal, Fig. 1
0
0.1
1
10
100
Ee - Irradiance
10
100
1000
1.0
f = f0
0.9
0.8
0.7
f = 30 kHz
0.6
0.5
f = 20 kHz
0.4
f = 10 kHz
0.3
0.2
0.1
f = 100 Hz
0
1
10 000
10
100
1000
ΔVsRMS - AC Voltage on DC Supply Voltage (mV)
(mW/m2)
Fig. 4 - Output Pulse Diagram
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
1.2
500
E - Max. Field Strength (V/m)
Ee min./Ee - Rel. Responsivity
1
Fig. 6 - Sensitivity in Bright Ambient
ton
0.1
0.1
Ee - Ambient DC Irradiance (W/m2)
0.8
0.5
Wavelength of ambient
illumination: λ = 950 nm
3.0
Fig. 3 - Output Function
0.7
Correlation with ambient light sources:
10 W/m2 = 1.4 klx (std. illum. A, T = 2855 K)
10 W/m2 = 8.2 klx (daylight, T = 5900 K)
4.5
t
t off
t on
5.0
Ee min. - Threshold Irradiance (mW/m2)
Ee
Vishay Semiconductors
1.0
0.8
0.6
0.4
f = f0 ± 5 %
f (3 dB) = f0/7
0.2
450
400
350
300
250
200
150
100
50
0.0
0.7
16926
0.9
1.1
0
1.3
0
20747
f/f0 - Relative Frequency
Fig. 5 - Frequency Dependence of Responsivity
Rev. 1.3, 10-Nov-15
500
1000
1500
2000
2500
3000
f - EMI Frequency (MHz)
Fig. 8 - Sensitivity vs. Electric Field Disturbances
3
Document Number: 82462
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP581.., TSOP583.., TSOP585..
www.vishay.com
Vishay Semiconductors
0°
0.9
10°
20°
30°
Max. Envelope Duty Cycle
0.8
TSOP581..
0.7
40°
0.6
1.0
0.5
TSOP583..
0.4
0.3
0.9
50°
0.8
60°
70°
0.2
0.7
80°
0.1
TSOP585..
0
0
20
40
60
80
100
120
0.6
140
19258
Burst Length (number of cycles/burst)
0.4
0.2
0
drel - Relative Transmission Distance
Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length
Fig. 12 - Horizontal Directivity
0°
0.40
10°
20°
30°
Ee min. - Sensitivity (mW/m2)
0.35
0.30
40°
0.25
1.0
0.20
0.9
50°
0.15
0.8
60°
0.10
70°
0.7
0.05
80°
0
-30
-10
10
30
50
70
0.6
90
Tamb - Ambient Temperature (°C)
1.0
0.8
0.6
0.4
0.2
850
950
1050
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1.5
1150
λ - Wavelength (nm)
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
VS - Supply Voltage (V)
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
Rev. 1.3, 10-Nov-15
0
0.8
1.2
94 8408
0.2
Fig. 13 - Vertical Directivity
Ee min. - Sensitivity (mW/m2)
S (λ)rel - Relative Spectral Sensitivity
Fig. 10 - Sensitivity vs. Ambient Temperature
0
750
0.4
d rel - Relative Transmission Distance
19259
Fig. 14 - Sensitivity vs. Supply Voltage
4
Document Number: 82462
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP581.., TSOP583.., TSOP585..
www.vishay.com
Vishay Semiconductors
SUITABLE DATA FORMAT
IR Signal
These products are designed to suppress spurious output
pulses due to noise or disturbance signals. Data and
disturbance signals can be distinguished by the devices
according to carrier frequency, burst length and envelope
duty cycle. The data signal should be close to the
band-pass center frequency (e.g. 38 kHz) and fulfill the
conditions in the table below.
When a data signal is applied to the IR receiver in the
presence of a disturbance signal, the sensitivity of the
receiver is reduced to insure that no spurious pulses are
present at the output. Some examples of disturbance
signals which are suppressed are:
0
5
• DC light (e.g. from tungsten bulb or sunlight)
10
15
20
Time (ms)
16920
Fig. 15 - IR Disturbance from Fluorescent Lamp
with Low Modulation
• Continuous signals at any frequency
• Modulated IR signals from common fluorescent lamps
(example of noise pattern is shown in Fig. 15 or Fig. 16)
IR Signal
• 2.4 GHz and 5 GHz Wi-Fi
0
5
10
15
20
Time (ms)
16921
Fig. 16 - IR Disturbance from Fluorescent Lamp
with High Modulation
TSOP581..
TSOP583..
TSOP585..
Minimum burst length
6 cycles/burst
6 cycles/burst
6 cycles/burst
After each burst of length
A gap time is required of
6 to 70 cycles
≥ 10 cycles
6 to 35 cycles
≥ 10 cycles
6 to 24 cycles
≥ 10 cycles
70 cycles
35 cycles
24 cycles
> 1.2 x burst length
> 6 x burst length
> 25 ms
2000
2000
2000
For bursts greater than
a minimum gap time in the data
stream is needed of
Maximum number of continuous
short bursts/second
MCIR code
Yes
Preferred
Yes
XMP-1, XMP-2 code
Yes
Preferred
Yes
Mild disturbance patterns
are suppressed (example:
signal pattern of Fig. 15)
Complex disturbance patterns
are suppressed (example:
signal pattern of Fig. 16)
Critical disturbance
patterns are suppressed,
e.g. highly dimmed LCDs
Suppression of interference from
fluorescent lamps
Note
• For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP582.., TSOP584..
Rev. 1.3, 10-Nov-15
5
Document Number: 82462
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP581.., TSOP583.., TSOP585..
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
5
4.8
(4)
2.8
(5.55)
6.95 ± 0.3
8.25 ± 0.3
R2
0.9
1.1
30.5 ± 0.5
(1.54)
0.85 max.
0.7 max.
2.54 nom.
2.54 nom.
0.5 max.
1.2 ± 0.2
Marking area
technical drawings
according to DIN
specifications
Not indicated to lerances ± 0.2
Drawing-No.: 6.550-5263.01-4
Issue: 12; 16.04.10
19009
Rev. 1.3, 10-Nov-15
R2
6
Document Number: 82462
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000