TSOP381.., TSOP383.., TSOP385.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES • Very low supply current • Photo detector and preamplifier in one package • Internal filter for PCM frequency • Supply voltage: 2.5 V to 5.5 V • Improved immunity against ambient light • Insensitive to supply voltage ripple and noise • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 19026 DESCRIPTION These products are miniaturized receivers for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. MECHANICAL DATA Pinning for TSOP381.., TSOP383.., TSOP385..: 1 = OUT, 2 = GND, 3 = VS The TSOP383.. series devices are optimized to suppress almost all spurious pulses from energy saving lamps like CFLs. AGC3 may also suppress some data signals if continuously transmitted. The TSOP381.. series are provided primarily for compatibility with old AGC1 designs. New designs should prefer the TSOP383.. series containing the newer AGC3. The TSOP385.. series contain a very robust AGC5. This series should only be used for critically noisy environments. These components have not been qualified according to automotive specifications. PARTS TABLE LEGACY, FOR SHORT BURST REMOTE CONTROLS (AGC1) NOISY ENVIRONMENTS AND SHORT BURSTS (AGC3) VERY NOISY ENVIRONMENTS AND SHORT BURSTS (AGC5) 30 kHz TSOP38130 TSOP38330 TSOP38530 33 kHz TSOP38133 TSOP38333 TSOP38533 36 kHz TSOP38136 TSOP38336 (1) TSOP38536 38 kHz TSOP38138 TSOP38338 (2)(3)(4)(5) TSOP38538 40 kHz TSOP38140 TSOP38340 TSOP38540 56 kHz TSOP38156 TSOP38356 TSOP38556 AGC Carrier frequency Package Minicast Pinning 1 = OUT, 2 = GND, 3 = VS Dimensions (mm) 5.0 W x 6.95 H x 4.8 D Mounting Leaded Application Best remote control code Rev. 1.4, 09-Nov-15 Remote control (1) MCIR (2) Mitsubishi 1 (3) RECS-80 Code (4) r-map (5) XMP-1, XMP-2 Document Number: 81743 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP381.., TSOP383.., TSOP385.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 17170_5 16833-13 R1 Transmitter with TSALxxxx 3 VS 1 Input Band pass AGC µC OUT Demodulator VO GND 2 PIN + VS C1 Circuit 30 kΩ IR receiver GND R1 and C1 are recommended for protection against EOS. Components should be in the range of 33 Ω < R1 < 1 kΩ, C1 > 0.1 µF. Control circuit ABSOLUTE MAXIMUM RATINGS PARAMETER Supply voltage Supply current Output voltage Output current Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature TEST CONDITION SYMBOL VS IS VO IO Tj Tstg Tamb Ptot Tsd Tamb ≤ 85 °C t ≤ 10 s, 1 mm from case VALUE -0.3 to +6 3 -0.3 to (VS + 0.3) 5 100 -25 to +85 -25 to +85 10 260 UNIT V mA V mA °C °C °C mW °C Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION Ev = 0, VS = 3.3 V Ev = 40 klx, sunlight SYMBOL ISD ISH VS MIN. 0.27 2.5 TYP. 0.35 0.45 - MAX. 0.45 5.5 UNIT mA mA V Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 200 mA IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 Angle of half transmission distance d - 45 - m VOSL - - 100 mV Ee min. - 0.12 0.25 mW/m2 Ee max. ϕ1/2 30 - ± 45 - W/m2 deg Supply current Supply voltage Transmission distance Output voltage low Minimum irradiance Maximum irradiance Directivity TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 0.40 Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms) tpo - Output Pulse Width (ms) Ee t tpi *) T *) tpi ≥ 6/f0 is recommended for optimal function Output Signal VO 1) 2) VOH 14337 3/f0 < td < 9/f0 tpi - 4/f0 < tpo < tpi + 6/f0 0.35 0.30 0.25 Output pulse width 0.20 0.15 Input burst length 0.10 λ = 950 nm, optical test signal, Fig. 1 0.05 0 VOL td 1) tpo 2) 0.1 t 20771 Fig. 1 - Output Active Low Rev. 1.4, 09-Nov-15 1 10 100 1000 10 000 100 000 Ee - Irradiance (mW/m²) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient 2 Document Number: 81743 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP381.., TSOP383.., TSOP385.. www.vishay.com Vishay Semiconductors 600 µs t 600 µs t = 60 ms 94 8134 Output Signal, (see Fig. 4) VO VOH VOL t off t on 4.0 Ee min. - Threshold Irradiance (mW/m2) Optical Test Signal Ee t Correlation with ambient light sources: 2 3.5 10 W/m = 1.4 klx (std. illum. A, T = 2855 K) 10 W/m2 = 8.2 klx (daylight, T = 5900 K) 3.0 2.0 1.5 1.0 0.5 0 0.01 Ee min. - Threshold Irradiance (mW/m2) ton, toff - Output Pulse Width (ms) ton 0.6 0.5 toff 0.4 0.3 0.2 λ = 950 nm, optical test signal, Fig. 3 0 0.1 1 10 100 1000 10 000 Ee - Irradiance (mW/m2) 20759 10 100 3.0 2.5 f = f0 f = 30 kHz f = 10 kHz f = 100 Hz 2.0 1.5 1.0 0.5 0 1 10 100 1000 ΔVS RMS - AC Voltage on DC Supply Voltage (mV) Fig. 4 - Output Pulse Diagram Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 1.2 1.0 f = 38 kHz, Ee = 2 mW/m² 0.9 1.0 Max. Envelope Duty Cycle Ee min./Ee - Relative Responsivity 1 Fig. 6 - Sensitivity in Bright Ambient 0.8 0.1 0.1 Ee - Ambient DC Irradiance (W/m2) 20757 Fig. 3 - Output Function 0.7 Wavelength of ambient illumination: λ = 950 nm 2.5 0.8 0.6 0.4 f = f0 ± 5 % Δf(3 dB) = f0/10 0.2 0.8 0.7 0.6 TSOP381.. TSOP391.. 0.5 0.4 0.3 TSOP383.., TSOP393.. 0.2 0.1 0.0 TSOP385.., TSOP395.. 0 0.7 16925 0.9 1.1 0 1.3 22180-7 f/f0 - Relative Frequency Fig. 5 - Frequency Dependence of Responsivity Rev. 1.4, 09-Nov-15 20 40 60 80 100 120 Burst Length (Number of Cycles/Burst) Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length 3 Document Number: 81743 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP381.., TSOP383.., TSOP385.. Ee min. - Threshold Irradiance (mW/m2) www.vishay.com Vishay Semiconductors 0.30 0° 10° 20° 30° 0.25 0.20 40° 1.0 0.15 0.10 0.9 50° 0.8 60° 70° 0.05 0.7 80° 0 -30 -10 10 30 50 70 90 0.6 Tamb - Ambient Temperature (°C) 0.4 Fig. 9 - Sensitivity vs. Ambient Temperature 0 Fig. 12 - Vertical Directivity 0.30 Ee min. - Sensitivity (mW/m2) 1.2 S (λ)rel - Relative Spectral Sensitivity 0.2 d rel - Relative Transmission Distance 19259 1.0 0.8 0.6 0.4 0.2 0.25 0.20 0.15 0.10 0.05 0.00 0 750 850 1050 950 1 1150 λ - Wavelength (nm) 94 8408 Fig. 10 - Relative Spectral Sensitivity vs. Wavelength 0° 10° 2 3 4 5 VS - Supply Voltage (V) Fig. 13 - Sensitivity vs. Supply Voltage 20° 30° 40° 1.0 0.9 50° 0.8 60° 70° 0.7 80° 0.6 19258 0.4 0.2 0 drel - Relative Transmission Distance Fig. 11 - Horizontal Directivity Rev. 1.4, 09-Nov-15 4 Document Number: 81743 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP381.., TSOP383.., TSOP385.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT IR Signal This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device’s band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the product in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver’s output. Some examples which are suppressed are: 0 • DC light (e.g. from tungsten bulbs sunlight) 5 • Continuous signals at any frequency 10 15 20 Time (ms) 16920 Fig. 14 - IR Disturbance from Fluorescent Lamp with Low Modulation IR Signal • Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 14 or Fig. 15) 0 5 16921 10 15 20 Time (ms) Fig. 15 - IR Disturbance from Fluorescent Lamp with High Modulation TSOP381.. TSOP383.. TSOP385.. Minimum burst length 6 cycles/burst 6 cycles/burst 6 cycles/burst After each burst of length A gap time is required of 6 to 70 cycles ≥ 10 cycles 6 to 35 cycles ≥ 10 cycles 6 to 24 cycles ≥ 10 cycles For bursts greater than a minimum gap time in the data stream is needed of 70 cycles 35 cycles 24 cycles > 1.2 x burst length > 6 x burst length > 25 ms Maximum number of continuous short bursts/second 2000 2000 2000 Yes MCIR code Yes Preferred RCMM code Yes Preferred Yes XMP-1, XMP-2 code Yes Preferred Yes Mild disturbance patterns are suppressed (example: signal pattern of Fig. 14) Complex disturbance patterns are suppressed (example: signal pattern of Fig. 15) Critical disturbance patterns are suppressed, e.g. highly dimmed LCDs Suppression of interference from fluorescent lamps Note • For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP382.., TSOP384.. Rev. 1.4, 09-Nov-15 5 Document Number: 81743 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP381.., TSOP383.., TSOP385.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 5 4.8 (4) 2.8 (5.55) 6.95 ± 0.3 8.25 ± 0.3 R2 0.9 1.1 30.5 ± 0.5 (1.54) 0.85 max. 0.7 max. 2.54 nom. 2.54 nom. 0.5 max. 1.2 ± 0.2 Marking area technical drawings according to DIN specifications Not indicated to lerances ± 0.2 Drawing-No.: 6.550-5263.01-4 Issue: 12; 16.04.10 19009 Rev. 1.4, 09-Nov-15 R2 6 Document Number: 81743 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000