TSMP1138 www.vishay.com Vishay Semiconductors IR Sensor Module for Remote Control Systems FEATURES • Photo detector and preamplifier in one package • AC coupled response from 30 kHz to 55 kHz, all data formats • If the IR singal strength is less then 300 mW/m2 (distance more than 0.6 m with a typical IR remote control), the frequency range is up to 60 kHz • Improved shielding disturbance 1 2 94 8691 3 against electrical field • AGC to suppress ambient noise • High sensitivity, long receiving range MECHANICAL DATA • Supply voltage: 2.5 V to 5.5 V Pinning: • Carrier out signal for IR repeater applications 1 = GND, 2 = Carrier OUT, 3 = VS • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 DESCRIPTION The TSMP1138 is a miniaturized sensor for receiving the modulated signal of infrared remote control systems. A PIN diode and preamplifier are assembled on a lead frame, the epoxy package is designed as an IR filter. The modulated output signal, carrier out, can be used for repeater applications and code learning applications. This component has not been qualified according to automotive specifications. PARTS TABLE Carrier frequency 38 kHz TSMP1138 Package Cast Pinning 1 = GND, 2 = Carrier OUT, 3 = VS Dimensions (mm) 10.0 W x 12.5 H x 5.8 D Mounting Leaded Application Repeater BLOCK DIAGRAM APPLICATION CIRCUIT 16833_11 3 33 kΩ R1 100 Ω VS AGC Band pass Comparator Rev. 1.3, 08-Jul-14 Control circuit C1 4.7 µF OUT VO 1 PIN Supply voltage +5V TSAL6400 33 kΩ 2 Input R3 680 Ω TSMP1138 R4 3Ω GND 0V Recommended circuit for best sensitivity of the TSOP9xx38 in repeater applications. It limits the output voltage swing VO to about 0.7 V in order to avoid internal coupling. GND 1 Document Number: 82484 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSMP1138 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT VS -0.3 to +6 V Supply voltage (pin 3) Supply current (pin 3) IS 5 mA Output voltage (pin 2) VO -0.3 to 5.5 V VS - VO -0.3 to (VS + 0.3) V IO 5 mA Voltage at output to supply Output current (pin 2) Junction temperature Storage temperature range Operating temperature range 100 °C -25 to +85 °C Tamb -25 to +85 °C Tamb ≤ 85 °C Ptot 10 mW t ≤ 10 s, 1 mm from case Tsd 260 °C Power consumption Soldering temperature Tj Tstg Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER Supply current (pin 3) TEST CONDITION SYMBOL MIN. TYP. MAX. Ev = 0, VS = 5 V ISD 0.55 0.7 0.9 Ev = 40 klx, sunlight ISH Supply voltage d IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 VOSL Minimum irradiance Less than 5 missing or 5 additional sub carrier pulses related to one burst Ee min. Maximum irradiance Less than 5 missing or 5 additional sub carrier pulses related to one burst Ee max. Angle of half transmission distance ϕ1/2 Transmission distance Output voltage low (pin 2) Directivity mA 0.8 VS Ev = 0, test signal see fig. 1, IR diode TSAL6200, IF = 400 mA UNIT mA 2.5 5.5 V 30 m 0.5 100 mV 1 mW/m2 W/m2 30 ± 55 deg TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Optical Test Signal: IR diode TSAL6200, IF = 0.25 A, N = 15 carrier pulses per burst, f = 38 kHz, burst repetition time: 3 ms 3.5 Ee min. - Detection Threshold (mW/m²) Ee t tpi - burst length VO tpi ≥ 6 carrier cycles is recommended for optimum function VOH 3 2.5 2 1.5 1 0.5 0 VOL 21648 The number of carrier- out-pulses might not be exactly same as the number of carrier cycles in tpi (input burst) 30 t 21772 Fig. 1 - Output Function Rev. 1.3, 08-Jul-14 35 40 45 50 55 60 fo - Carrier Frequency (kHz) Fig. 2 - Frequency Dependence of Sensitivity 2 Document Number: 82484 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSMP1138 S (λ)rel - Relative Spectral Sensitivity www.vishay.com Vishay Semiconductors 1.2 1.0 0.8 0.6 0.4 0.2 0 750 850 1150 1050 950 λ - Wavelength (nm) 94 8408 Fig. 3 - Relative Spectral Sensitivity vs. Wavelength - 20 - 10 0 10 0.2 0 0.2 20 - 30 - 40 0.6 94 8153 0.4 0.4 0.6 drel - Relative Transmission Distance Fig. 4 - Horizontal Directivity ϕx - 20 - 10 0 10 0.2 0 0.2 20 - 30 - 40 y x 0.6 94 8152 0.4 0.4 0.6 drel - Relative Transmission Distance Fig. 5 - Vertical Directivity ϕy Rev. 1.3, 08-Jul-14 3 Document Number: 82484 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSMP1138 www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 10 ± 0.3 (9.2) 0.65 + 0.10 - 0.15 0.8 max. 30.6 ± 0.5 12.5 ± 0.4 Center of sensitive area 0.5 Area not plane 0.4 + 0.15 - 0.05 2.54 nom. + 0.10 - 0.05 1.4 ± 0.3 4 ± 0.3 3 x 2.54 = 7.62 nom. 5.8 ± 0.3 R 2.75 technical drawings according to DIN specifications Drawing-No.: 6.550-5095.01-4 Issue: xx; 20.05.09 96 12116-1 Rev. 1.3, 08-Jul-14 4 Document Number: 82484 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Cast IR Receiver Packaging Options www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Vishay offers stock Cast IR Receivers in three different packages: • Loose packed in tubes and mounted on tape for reel or ammopack • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 • Vishay IR receiver with plastic holders are packed in plastic tubes AVAILABLE FOR • TSOP312.. • TSOP311.. • TSOP12... • TSOP11... • TSOP13... • TSOP313.. • TSOP314.. 1 2 • TSOP315.. 94 8691 3 • TSMP1138 LOOSE PACKED IN TUBE PACKAGING DIMENSIONS in millimeters (11.7) ORDERING INFORMATION (7.5) (3.2) 2 or 3 digit product series O = for IR receiver applications M = for repeater/learning applications d d d 2 digit frequency (35) d (13.5) d (2.7) P (8) Note • d = “digit”, please consult the list of available devices create a valid part number. EXAMPLE: TSOP1238 PACKAGING QUANTITY (12.2) d (5.2) S (4.5) T (3.1) • 50 pieces per tube Wall thickness: 0.6 (4) • 20 tubes per carton (538) (13) (11.8) (13) 1:1 Drawing-No.: 9.700-5377.0-4 Rev. 1; Date: 26.04.2011 Rev. 1.5, 02-Apr-12 1 Printing for tubes 1.400-5548.0-3 version 1 Document Number: 81639 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Cast IR Receiver Packaging Options www.vishay.com Vishay Semiconductors TAPE AND REEL/AMMOPACK Up to 3 consecutive components may be missing if the gap is followed by at least 6 components. A maximum of 0.5 % of the components per reel quantity may be missing. At least 5 empty positions are present at the start and the end of the tape to enable insertion. Tensile strength of the tape: > 15 N Pulling force in the plane of the tape, at right angles to the reel: > 5 N Ø 355 ±1 Ø 30 Label H 12.7 ± 1 ±2 0.9 max. 0.3 ± 0.2 Kraftpaper 9 ± 0.5 Ø 4 ± 0.2 Adhesive Tape Tape 6.35 ± 0.7 dd = 21 (back view) 12.7 ± 0.2 dd = 12 (front view) 80079 tape on reel-s 12 ± 0.3 5.08 ± 0.2 2.54 ± 0.2 2.54 +1 18 -0.5 80079 tape-s VERSION DIMENSION “H” BS 20 ± 0.5 PS 23.3 ± 0.5 OS 26 ± 0.5 130 1 360 50 80079 ammopack-s ORDERING INFORMATION T S d P O = for IR receiver applications M = for repeater/learning applications d d d 2 or 3 digit product series d d 2 digit frequency S S 1 SS1 for T and R, bulk or ammopack d d dd = BS, PS, or OS d d Z Tape dd = Ammopack and 12 or 21 reel Note • d = ”digit”, please consult the list of available devices create a valid part number. EXAMPLE: TSOP1238SS1BS12 PACKAGING QUANTITY TSOP1238SS1BS12Z • 1000 pieces per reel • 1000 pieces per ammopack Rev. 1.5, 02-Apr-12 2 Document Number: 81639 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Cast IR Receiver Packaging Options www.vishay.com Vishay Semiconductors OUTER PACKAGING CARTON BOX DIMENSIONS in millimeters Length Thickness Width 22127 KINDS OF CARTON BOX THICKNESS WIDTH LENGTH Packaging Plastic Tubes (Normal/auxiliary devices) 82 152 564 Tape and Reel Box (Taping in reels) 400 310 410 Ammo-Box (Zigzag taping) 50 130 350 Rev. 1.5, 02-Apr-12 3 Document Number: 81639 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000