PSC600 Series DC/DC INDUSTRIAL CONVERTER FEATURES • • • • • • • • • • • • 250W - 800W Industrial Converter Optimized input voltage ranges Input ranges from 24 to 440Vdc Single outputs from 5 to 125Vdc Reverse input voltage protection Conformally coating - tropic Alarm relay output Accessible on front - Output voltage adjustment - Output voltage measurement - Output OK status green LED High efficiency > 90% Operating Temp -25C to 70C with no derating Fully encapsulated meets IP20 19' Rack Mount or DIN Mount or Wall Mount SPECIFICATIONS OPERATING INPUT Input voltage Reverse input voltage protection 24V, 48V, 110V, 220V See Selection Table for details Parallel diode (Input code: 24, 48) Series diode (Input code: 110, 220) OUTPUT Output Voltage See Selection Table Output Current See Selection Table Source regulation 0.2%. Load regulation 0.2%. Output ripple (50kHz) Typ. 20mV p-p typ. Input ripple attenuation 150:1 On output 50 to 400Hz Voltage adjustment Current limit protection Efficiency 80%–93% Design topology Push-pull / Full-Bridge Switching frequency 50kH Overvoltage protection Yes, 115% of nominal voltage Isolation Input / Output: 2.5kVac, 4kVdc Input / Case: 4kVdc Output / Case: 2kVdc, all outputs ENVIRONMENTAL Operating temperature -25°C to 70°C (100% load, single output >10Vdc). -25°C to +55°C (100% load, single output <10Vdc). 90% - 110%. Temperature Coefficient 0.02%/°C. 105%. Rectangular Cooling Convectional cooling. Overvoltage protection 115%. Storage temperature -40°C to 85°C. Under voltage alarm 90% of nominal output. STANDARDS Remote sense Option S. Safety IEC60950 Soft start Yes. EMC EN 61000-6-3, Emission EN61000-6-2, Immunity EN IEC 61000-4-4, 4kV EN IEC 61000-4-5 level 2 & 3 AS/NZS CISPR11: 2002 Group1 Class A Start-up time1s Hold-up time 2-25ms Efficiency 80 - 93% C-Tick Switching frequency 50 kHz MECHANICAL Dimensions Weight www.powerbox.com.au - 1800 251 380 www.powerbox.co.nz - 0800 104 480 See Technical Illustrations Base mechanic unit; 3.3Kg Base mechanic unit + 1 extra heatsink 4.0kg Base mechanic unit + 2 extra heatsinks 4.7kg Doc. No. PSC600 Rev.B 20-04-16 PSC600 Series DC/DC INDUSTRIAL CONVERTER FEATURES FEATURES Overvoltage protection OVP The output voltage is limited to 15% over nominal output voltage by a extra regulated circuit Under voltage alarm A built in alarm changes to alarm state if the converter output voltage drops 10% below nominal output. The DC OK LED is also controlled by the alarm circuit. The alarm has a relay output with both [NO] and [NC] function. The relay rating is 30V 1A Reverse input voltage Protection On input code 24 and 48 the reverse voltage protection is provided by a parallel diode. This diode is only intended to blow and external input fuse. On input code 110 and 220, the reverse voltage protection is provided by a series diode. The converter will never start. Inrush current limit On input code 110 and 220 the inrush limit circuit is always active thus acting at voltage dips below the stop level >10ms. On input code 24 and 48 this function is optional. Adjustment & measurement Output voltage adjust potentiometer and output voltage measurement points are accessible from the front panel. Conformal Coating the PSC series is conformally coated to withstand non-condensing tropical environment. OPTIONAL FEATURES Wider input range The PSC600 series can be supplied with wide inptu range to meet train or mobile applications demands Built in series diode - C Series diode on the output, which is mounted inside the case. Use this option when the output is connected in parallel with other power supply to achieve redundancy Built in series diode w/ resistor - CR The CR option automatically balance the load between 2 or more paralleled PSC600 units. Used in hotswap. The voltage sensing can be put at the load to compensate for voltage drop. The sense circuit is a standard feature on 5V Remote Sense - S outputs. On input code 24 and 48 the inrush limit circuit is optional. This option affects the input voltage range. The circuit is always Inrush Current LImit active thus acting at voltage dips below the stop level > 10ms. Higher insulation on output - E2 Output/case 2.5kVAC for 12 to 125Vdc Over current shutdown - OCSD The PSC600 series can provide over current during a limited time. The OCSD circuit shut down the unit when a preset time has passed. This delay can be pre-set between 100ms to 3 seconds. www.powerbox.com.au - 1800 251 380 www.powerbox.co.nz - 0800 104 480 Doc. No. PSC600 Rev.B 20-04-16 PSC600 Series DC/DC INDUSTRIAL CONVERTER SELECTION TABLE MODEL NUMBER INPUT PSC250 24/5 20-32V 5V OUTPUT 50A 250W PSC400 24/12 20-32V 12V 33A 400W PSC400 24/15 20-32V 15V 27A 400W PSC600 24/24 20-32V 24V 25A 600W PSC600 24/48 20-32V 48V 12.5A 600W PSC600 24/110 20-32V 110V 5.5A 600W PSC600 24/125 20-32V 125V 4.8A 600W PSC250 48/5 41-60V 5V 50A 250W PSC400 48/12 41-60V 12V 33A 400W PSC700 48/12 41-60V 12V 60A 720W PSC400 48/15 41-60V 15V 27A 400W PSC800 48/15 41-60V 15V 54A 800W PSC600 48/24 41-60V 24V 25A 600W PSC800 48/24 41-60V 24V 33A 800W PSC600 48/48 41-60V 48V 12.5A 600W PSC800 48/48 41-60V 48V 17A 800W PSC600 48/110 41-60V 110V 5.5A 600W PSC800 48/110 41-60V 110V 7.3A 800W PSC600 48/125 41-60V 125V 4.8A 600W PSC800 48/125 41-60V 125V 6.4A 800W PSC250 110/5 93-150V 5V 50A 250W PSC400 110/12 93-150V 12V 33A 400W PSC700 110/12 93-150V 12V 60A 720W PSC400 110/15 93-150V 15V 27A 400W PSC800 110/15 93-150V 15V 54A 800W PSC600 110/24 93-150V 24V 25A 600W PSC800 110/24 93-150V 24V 33A 800W PSC600 110/48 93-150V 48V 12.5A 600W PSC800 110/48 93-150V 48V 17A 800W PSC600 110/110 93-150V 110V 5.5A 600W PSC800 110/110 93-150V 110V 7.3A 800W PSC600 110/125 93-150V 125V 4.8A 600W PSC800 110/125 93-150V 125V 6.4A 800W PSC250 220/5 187-300V 5V 50A 250W PSC400 220/12 187-300V 12V 33A 400W PSC700 220/12 187-300V 12V 60A 720W PSC400 220/15 187-300V 15V 27A 400W PSC800 220/15 187-300V 15V 54A 800W PSC600 220/24 187-300V 24V 25A 600W PSC800 220/24 187-300V 24V 33A 800W PSC600 220/48 187-300V 48V 12.5A 600W PSC800 220/48 187-300V 48V 17A 800W PSC600 220/110 187-300V 110V 5.5A 600W PSC800 220/110 187-300V 110V 7.3A 800W PSC600 220/125 187-300V 125V 4.8A 600W PSC800 220/125 187-300V 125V 6.4A 800W www.powerbox.com.au - 1800 251 380 www.powerbox.co.nz - 0800 104 480 POWER Doc. No. PSC600 Rev.B 20-04-16 PSC600 Series DC/DC INDUSTRIAL CONVERTER TECHNICAL ILLUSTRATIONS www.powerbox.com.au - 1800 251 380 www.powerbox.co.nz - 0800 104 480 Doc. No. PSC600 Rev.B 20-04-16 PSC600 Series DC/DC INDUSTRIAL CONVERTER TECHNICAL ILLUSTRATIONS www.powerbox.com.au - 1800 251 380 www.powerbox.co.nz - 0800 104 480 Doc. No. PSC600 Rev.B 20-04-16 PSC600 Series DC/DC INDUSTRIAL CONVERTER TECHNICAL ILLUSTRATIONS www.powerbox.com.au - 1800 251 380 www.powerbox.co.nz - 0800 104 480 Doc. No. PSC600 Rev.B 20-04-16 PSC600 Series DC/DC INDUSTRIAL CONVERTER TECHNICAL ILLUSTRATIONS www.powerbox.com.au - 1800 251 380 www.powerbox.co.nz - 0800 104 480 Doc. No. PSC600 Rev.B 20-04-16 PSC600 Series DC/DC INDUSTRIAL CONVERTER TECHNICAL ILLUSTRATIONS www.powerbox.com.au - 1800 251 380 www.powerbox.co.nz - 0800 104 480 Doc. No. PSC600 Rev.B 20-04-16 PSC600 Series DC/DC INDUSTRIAL CONVERTER TECHNICAL ILLUSTRATIONS www.powerbox.com.au - 1800 251 380 www.powerbox.co.nz - 0800 104 480 Doc. No. PSC600 Rev.B 20-04-16