CP Datasheet

CP
www.vishay.com
Vishay Dale
Wirewound/Metal Oxide Resistors, Commercial Power, Axial Lead
FEATURES
• High performance for low cost
• Meets or exceeds requirements of EIA
Standard RS-344
• High power to size ratio
• Ceramic cases are available with circuit board
stand-offs (designated with a -3 model ending)
• Special inorganic potting compound and
ceramic case provide high thermal conductivity
in a fireproof package
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
Available
Available
Available
STANDARD ELECTRICAL SPECIFICATIONS
GLOBAL MODEL
POWER RATING
P40 °C
W
2
2
3
3
5
5
7
7
10
10
15
15
20
20
22
22
25
RESISTANCE RANGE Ω
METAL OXIDE (1)
RESISTANCE RANGE Ω
WIREWOUND (1)
WEIGHT
(typical)
g
2.0
2.2
3.4
3.6
4.8
5.0
6.8
7.0
9.5
9.9
16.8
17.4
22.8
23.6
24.5
25.3
37.0
TOLERANCE
±%
CP0002
0.1 to 1K
100 to 30K
5, 10
CP0002...3
0.1 to 1K
100 to 30K
5, 10
CP0003
0.1 to 2K
150 to 33K
5, 10
CP0003...3
0.1 to 2K
150 to 33K
5, 10
CP0005
0.1 to 2.4K
150 to 50K
5, 10
CP0005...3
0.1 to 2.4K
150 to 50K
5, 10
CP0007
0.1 to 7K
5, 10
CP0007...3
0.1 to 7K
5, 10
CP0010
0.1 to 11K
5, 10
CP0010...3
0.1 to 11K
5, 10
CP0015
0.1 to 11K
5, 10
CP0015...3
0.1 to 11K
5, 10
CP0020
0.1 to 16K
5, 10
CP0020...3
0.1 to 16K
5, 10
CP0022
0.1 to 16K
5, 10
CP0022...3
0.1 to 16K
5, 10
CP0025
0.1 to 16K
5, 10
Note
(1) To specifically order a Wirewound sub-assembly for resistance values that overlap between the Wirewound and Metal Oxide technologies,
the model will be a CPxxxx...85 for standard body and CPxxxx...91 for body with stand-offs. To specifically order a Metal Oxide
sub-assembly for resistance values that overlap between the Wirewound and Metal Oxide technologies, the model will be a CPxxxx...100
for a standard body and CPxxxx...101 for body with stand-offs. If no dash type is specified, either technology may be supplied.
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
WIREWOUND CHARACTERISTICS
METAL OXIDE CHARACTERISTICS
Temperature Coefficient
ppm/°C ± 300 1 Ω and above; ± 600 below 1 Ω
± 300 (CP0002 to CP0005)
Short Time Overload
5 x rated power for 5 s
5 x rated power for 5 s
Terminal Strength
lb
10 minimum
10 minimum
Operating Temperature Range
°C
-65 to +275
-65 to +225
VAC
Dielectric Withstanding Voltage
1000
1000
Maximum Working Voltage
V
(P x R)1/2
(P x R)1/2
Note
• Wirewound CP resistors can reliably function as a fuse and as a resistor. Such components involve compromise between fusing and resistive
functions; therefore, each design should be tailored to the application to ensure optimum performance. Contact factory by using the e-mail
address at the bottom of this page for design assistance.
GLOBAL PART NUMBER INFORMATION
Global Part Numbering example: CP000515R00JE143
C
P
0
0
GLOBAL MODEL
(See Standard Electrical
Specifications Global
Model column for
options)
0
5
VALUE
R = Decimal
K = Thousand
R1500 = 0.15 Ω
1K500 = 1500 Ω
1
5
TOLERANCE
J = ± 5.0 %
K = ± 10.0 %
Historical Part Numbering example: CP-5-3 15 Ω 5 % B14
CP-5-3
15 Ω
HISTORICAL MODEL
Revision: 10-Nov-15
R
RESISTANCE VALUE
0
0
J
E
1
4
PACKAGING
E14 = Lead (Pb)-free bulk pack
E31 = Lead (Pb)-free four layer bulk pack
B14 = Bulk pack
B31 = Four layer bulk pack
3
SPECIAL
(Dash Number)
(up to 3 digits)
From 1 to 999
as applicable
5%
B14
TOLERANCE CODE
PACKAGING
Document Number: 30213
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CP
www.vishay.com
Vishay Dale
DIMENSIONS in inches [millimeters]
CPxxxx
F
typical
CPxxxx...3
F
typical
E
A
A
B
GLOBAL
MODEL
A (1)
± 0.031
[0.794]
0.688 [17.46]
0.688 [17.46]
0.875 [22.22]
0.875 [22.22]
0.875 [22.22]
0.875 [22.22]
1.391 [35.32]
1.391 [35.32]
1.875 [47.62]
1.875 [47.62]
1.875 [47.62]
1.875 [47.62]
2.500 [63.50]
2.500 [63.50]
2.500 [63.50]
2.500 [63.50]
2.500 [63.50]
B
± 0.031
[0.794]
C
± 0.031
[0.794]
C
D
C
0.125
[3.18]
typical
E
B
DIMENSIONS in inches [millimeters]
E
F
D
± 0.001 [0.025]
± 0.031
WIREWOUND METAL OXIDE
[0.794]
WIREWOUND METAL OXIDE ± 0.125 [3.175]
MINIMUM
0.032 [0.813] 0.0236 [0.600] 1.500 [38.10]
0.750 [19.05]
0.313 [7.94] 0.032 [0.813] 0.0236 [0.600] 1.500 [38.10]
0.750 [19.05]
0.036 [0.914]
0.032 [0.813]
1.500 [38.10]
1.000 [25.40]
0.375 [9.52] 0.036 [0.914]
0.032 [0.813]
1.500 [38.10]
1.000 [25.40]
0.036 [0.914]
0.032 [0.813]
1.500 [38.10]
1.000 [25.40]
0.406 [10.32] 0.036 [0.914]
0.032 [0.813]
1.500 [38.10]
1.000 [25.40]
0.036 [0.914]
1.500 [38.10]
0.469 [11.91] 0.036 [0.914]
1.500 [38.10]
0.036 [0.914]
1.500 [38.10]
0.469 [11.91] 0.036 [0.914]
1.500 [38.10]
0.036 [0.914]
1.500 [38.10]
0.625 [15.87] 0.036 [0.914]
1.500 [38.10]
0.036 [0.914]
1.500 [38.10]
0.625 [15.87] 0.036 [0.914]
1.500 [38.10]
0.036 [0.914]
1.500 [38.10]
0.625 [15.87] 0.036 [0.914]
1.500 [38.10]
0.040 [1.016]
1.500 [38.10]
-
CP0002
0.250 [6.35] 0.250 [6.35]
CP0002...3
0.250 [6.35] 0.250 [6.35]
CP0003
0.313 [7.94] 0.313 [7.94]
CP0003...3
0.313 [7.94] 0.313 [7.94]
CP0005
0.375 [9.52] 0.344 [8.73]
CP0005...3
0.375 [9.52] 0.344 [8.73]
CP0007
0.375 [9.52] 0.344 [8.73]
CP0007...3
0.375 [9.52] 0.344 [8.73]
CP0010
0.375 [9.52] 0.344 [8.73]
CP0010...3
0.375 [9.52] 0.344 [8.73]
CP0015
0.500 [12.70] 0.500 [12.70]
CP0015...3
0.500 [12.70] 0.500 [12.70]
0.500 [12.70] 0.500 [12.70]
CP0020 (2)
CP0020...3
0.500 [12.70] 0.500 [12.70]
CP0022
0.500 [12.70] 0.500 [12.70]
CP0022...3
0.500 [12.70] 0.500 [12.70]
CP0025
0.625 [15.87] 0.625 [15.87]
Notes
(1) Potting compound may extend outside of ceramic case up to 0.060 [1.52] maximum per side.
(2) Dimensions for the metal oxide are: A = 2.360 [59.94], B = 0.570 [14.48], C = 0.530 [13.46], E = 0.032 [0.813], F = 1.000 [25.40]
Element: Wirewound = Copper-nickel alloy
nickel-chrome alloy, depending on resistance value
Metal Oxide = High temperature fired metal oxide film
DERATING
or
Core: Wirewound = Woven fiberglass
Metal Oxide = Alumina ceramic
Body: Steatite ceramic case with inorganic potting
compound
End Caps: Tin plated steel
Terminals: Tinned copper
RATED POWER IN %
MATERIAL SPECIFICATIONS
120
100
80
60
Wirewound
40
20
Part Marking: DALE, model, wattage, value, tolerance, date
code
0
- 55
Metal Oxide
- 25
25
75
40
125
175
275
225
AMBIENT TEMPERATURE IN °C
PERFORMANCE
TEST
Thermal Shock
Short Time Overload
Dielectric Withstanding Voltage
Low Temperature Storage
Humidity
Load Life
Terminal Strength
Resistance to Solder Heat
Revision: 10-Nov-15
CONDITIONS OF TEST
-55 °C to +275 °C (+225 °C for Metal Oxide), 5 cycles, 30 min dwell time
5 x rated power for 5 s
1000 VRMS, for 1 min
-65 °C, full rated working voltage for 45 min
75 °C, 90 % to 100 % RH, 240 h
1000 h at rated power, + 25 °C, 1.5 h “ON”, 0.5 h “OFF”
5 pounds for 30 s; body twisted about axis, 3 x 360° rotations
Terminal immersed 3.5 s in molten solder at 1/8" to 3/16" from body
TEST LIMITS (EIA-344)
± (5.0 % + 0.05 Ω) ΔR
± (4.0 % + 0.05 Ω) ΔR
± (2.0 % + 0.05 Ω) ΔR
± (3.0 % + 0.05 Ω) ΔR
± (5.0 % + 0.05 Ω) ΔR
± (10.0 % + 0.05 Ω) ΔR
± (2.0 % + 0.05 Ω) ΔR
± (4.0 % + 0.05 Ω) ΔR
Document Number: 30213
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000