LT1078/LT1079 - Micropower, Dual and Quad, Single Supply, Precision Op Amps

LT1078/LT1079
Micropower, Dual and
Quad, Single Supply, Precision Op Amps
DESCRIPTIO
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
Available in 8-Pin SO Package
50μA Max Supply Current per Amplifier
70μV Max Offset Voltage
180μV Max Offset Voltage in 8-Pin SO
250pA Max Offset Current
0.6μVP-P, 0.1Hz to 10Hz Voltage Noise
3pAP-P, 0.1Hz to 10Hz Current Noise
0.4μV/°C Offset Voltage Drift
200kHz Gain Bandwidth Product
0.07V/μs Slew Rate
Single Supply Operation
Input Voltage Range Includes Ground
Output Swings to Ground while Sinking Current
No Pull-Down Resistors Needed
Output Sources and Sinks 5mA Load Current
U
APPLICATIO S
■
■
■
■
The LT ® 1078 is a micropower dual op amp in 8-pin
packages including the small outline surface mount package. The LT1079 is a micropower quad op amp offered in
the standard 14-pin packages. Both devices are optimized
for single supply operation at 5V. ±15V specifications are
also provided.
Micropower performance of competing devices is achieved
at the expense of seriously degrading precision, noise,
speed and output drive specifications. The design effort of
the LT1078/LT1079 was concentrated on reducing supply current without sacrificing other parameters. The
offset voltage achieved is the lowest on any dual or quad
nonchopper stabilized op amp—micropower or otherwise. Offset current, voltage and current noise, slew rate
and gain bandwidth product are all two to ten times better
than on previous micropower op amps.
The 1/f corner of the voltage noise spectrum is at 0.7Hz,
at least three times lower than on any monolithic op amp.
This results in low frequency (0.1Hz to 10Hz) noise
performance which can only be found on devices with an
order of magnitude higher supply current.
Battery or Solar-Powered Systems
Portable Instrumentation
Remote Sensor Amplifier
Satellite Circuitry
Micropower Sample-and-Hold
Thermocouple Amplifier
Micropower Filters
Both the LT1078 and LT1079 can be operated from a
single supply (as low as one lithium cell or two Ni-Cad
batteries). The input range goes below ground. The allNPN output stage swings to within a few millivolts of
ground while sinking current—no power consuming pull
down resistors are needed.
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
TYPICAL APPLICATIO
Single Battery, Micropower, Gain = 100, Instrumentation Amplifier
10.1k
Distribution of Input Offset Voltage
(LT1078 and LT1079 in H, J, N Packages)
16
1M
14
1M
INVERTING
INPUT
2
3
–
–
A
1/2 LT1078
3V (LITHIUM CELL)
1
10.1k
6
+
5
NONINVERTING
INPUT
+
TYPICAL PERFORMANCE
INPUT OFFSET VOLTAGE = 40μV
INPUT OFFSET CURRENT = 0.2nA
TOTAL POWER DISSIPATION = 240μW
COMMON MODE REJECTION = 110dB (AMPLIFIER LIMITED)
GAIN BANDWIDTH PRODUCT = 200kHz
–
B
1/2 LT1078
+
4
7
VS = 5V, 0V
TA = 25°C
12
8
OUT
LT1078/79 • TA01
OUTPUT NOISE = 85μVP-P 0.1Hz TO 10Hz
= 300μVRMS OVER FULL BANDWIDTH
INPUT RANGE = 0.03V TO 1.8V
OUTPUT RANGE = 0.03V TO 2.3V
(0.3mV ≤ VIN+ – VIN– ≤ 23mV)
OUTPUTS SINK CURRENT—NO PULL-DOWN RESISTORS
ARE NEEDED
PERCENT OF UNITS
■
10
8
6
4
2
0
–120
–80
–40
40
80
0
INPUT OFFSET VOLTAGE (μV)
120
1078/79 • TA02
10789fe
1
LT1078/LT1079
W W
U
W
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Supply Voltage ...................................................... ±22V
Differential Input Voltage ....................................... ±30V
Input Voltage ............... Equal to Positive Supply Voltage
............5V Below Negative Supply Voltage
Output Short-Circuit Duration .......................... Indefinite
Storage Temperature Range
All Grades ......................................... – 65°C to 150°C
Operating Temperature Range
LT1078AM/LT1078M/
LT1079AM/LT1079M (OBSOLETE) ..... – 55°C to 125°C
LT1078I/LT1079I .................................... – 40°C to 85°C
LT1078AC/LT1078C/LT1078S8/
LT1079AC/LT1079C .................................... 0°C to 70°C
Lead Temperature (Soldering, 10 sec).................. 300°C
W
U
U
PACKAGE/ORDER INFORMATION
TOP VIEW
TOP VIEW
TOP VIEW
V+
OUT A 1
8
7 OUT B
OUT A 1
A
–IN A 2
B
–IN A 2
8
+IN A 3
6 –IN B
V– 4
4
–IN B
5
+IN B
LT1078ACH
LT1078MH
OBSOLETE PACKAGES
14 OUT D
OUT A 1
A
D
ORDER PART
NUMBER
13 –IN D
12 +IN D
+IN A 3
11 V –
4
10 +IN C
+IN B 5
B
C
V+
5
OUT B
ORDER PART NUMBER
LT1078IS8
LT1078S8
PART MARKING
1078
TOP VIEW
OUT A 1
16 OUT D
A
D
+IN A 3
V+
4
–IN C
–IN B 6
OUT C
OUT B 7
NC 8
15 –IN D
14 +IN D
13 V–
+IN B 5
8
J PACKAGE
14-LEAD CERAMIC DIP
TJMAX = 150°C, θJA = 100°C/ W (J)
OUT A
6
TJMAX = 110°C, θJA = 220°C/ W
9
N PACKAGE
14-LEAD PDIP
TJMAX = 110°C, θJA = 130°C/ W (N)
7
NOTE: THIS PIN CONFIGURATION DIFFERS FROM THE
8-LEAD DIP PIN LOCATIONS. INSTEAD, IT FOLLOWS
THE INDUSTRY STANDARD LT1013DS8 SO PACKAGE
CONFIGURATION. FOR SIMILAR PERFORMANCE WITH
TRADITIONAL DIP PINOUT, SEE THE LT2078
–IN A 2
LT1079ACN
LT1079CN
LT1079IN
–IN A
B
LT1078AMJ8
LT1078MJ8
Consider the N8 and S8 Packages for Alternate Source
8
S8 PACKAGE
8-LEAD PLASTIC SO
J8 PACKAGE
8-LEAD PDIP
TJMAX = 150°C, θJA = 100°C/ W (J8)
TOP VIEW
2
–IN B 4
LT1078ACN8
LT1078CN8
LT1078IN8
ORDER PART NUMBER
–IN B 6
6
A
+IN B 3
ORDER PART NUMBER
TJMAX = 150°C, θJA = 150°C/ W, θJC = 45°C/ W
OUT B 7
OUT B
N8 PACKAGE
8-LEAD PDIP
TJMAX = 100°C, θJA = 130°C/ W (N8)
V – (CASE)
H PACKAGE
8-LEAD TO-5 METAL CAN
V+
B
V–
5 +IN B
+IN A 3
–IN A 2
7
A
+IN A 1
V+
ORDER PART
NUMBER
LT1079ISW
LT1079SW
12 +IN C
B
C
11 –IN C
10 OUT C
9
NC
SW PACKAGE
16-LEAD PLASTIC SO WIDE
LT1079MJ
NOTE: FOR 14-PIN NARROW
PACKAGE SEE THE LT2079
TJMAX = 110°C, θJA = 150°C/ W
OBSOLETE PACKAGE
Consider the N Packages for Alternate Source
10789fe
2
LT1078/LT1079
ELECTRICAL CHARACTERISTICS
SYMBOL PARAMETER
VOS
Input Offset Voltage
VS = 5V, 0V, VCM = 0.1V, VO = 1.4V, TA = 25°C unless otherwise noted.
CONDITIONS (NOTE 2)
LT1078AC/LT1079AC
LT1078AM/LT1079AM
MIN
TYP
MAX
LT1078
LT1078IS8/LT1078S8
LT1079
LT1079ISW/LT1079SW
30
70
35
100
LT1078C/LT1079C
LT1078I/LT1079I
LT1078M/LT1079M
LT1078S8/LT1079SW
MIN
TYP
MAX
40
60
40
60
120
180
150
300
UNITS
μV
μV
μV
μV
ΔVOS
ΔTime
Long Term Input Offset
Voltage Stability
0.4
IOS
Input Offset Current
0.05
0.25
0.05
0.35
nA
IB
Input Bias Current
6
8
6
10
nA
en
Input Noise Voltage
0.1Hz to 10Hz (Note 3)
0.6
1.2
0.6
μVP-P
Input Noise Voltage Density
fO = 10Hz (Note 3)
fO = 1000Hz (Note 3)
29
28
45
37
29
28
nV√Hz
nV√Hz
Input Noise Current
0.1Hz to 10Hz (Note 3)
2.3
4.0
2.3
pAP-P
Input Noise Current Density
fO = 10Hz (Note 3)
fO = 1000Hz
0.06
0.02
0.10
0.06
0.02
pA√Hz
pA√Hz
Input Resistance
Differential Mode
Common Mode
(Note 4)
in
μV/Mo
0.5
400
800
6
300
800
6
MΩ
GΩ
Input Voltage Range
3.5
0
3.8
– 0.3
3.5
0
3.8
– 0.3
V
V
CMRR
Common Mode Rejection Ratio VCM = 0V to 3.5V
97
110
94
108
dB
PSRR
Power Supply Rejection Ratio
VS = 2.3V to 12V
102
114
100
114
dB
AVOL
Large-Signal Voltage Gain
VO = 0.03V to 4V, No Load
VO = 0.03V to 3.5V, RL = 50k
200
150
1000
600
150
120
1000
600
V/mV
V/mV
Maximum Output Voltage
Swing
Output Low, No Load
Output Low, 2k to GND
Output Low, ISINK = 100μA
3.5
0.55
95
6
1.0
130
3.5
0.55
95
6
1.0
130
mV
mV
mV
Output High, No Load
Output High, 2k to GND
4.2
3.5
4.4
3.9
4.2
3.5
4.4
3.9
V
V
0.04
0.07
0.04
0.07
V/μs
200
kHz
SR
Slew Rate
AV = 1, VS = ± 2.5V
GBW
Gain Bandwidth Product
fO ≤ 20kHz
IS
Supply Current per Amplifier
200
38
Channel Separation
ΔVIN = 3V, RL = 10k
130
Minimum Supply Voltage
(Note 5)
2.2
50
39
55
130
2.3
2.2
μA
dB
2.3
V
10789fe
3
LT1078/LT1079
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the temperature range
– 40°C ≤ TA ≤ 85°C for I grades, – 55°C ≤ TA ≤ 125°C for AM/M grades. VS = 5V, 0V, VCM = 0.1V, VO = 1.4V unless otherwise noted.
SYMBOL PARAMETER
VOS
Input Offset Voltage
ΔVOS
ΔT
Input Offset Voltage Drift
(Note 6)
IOS
Input Offset Current
LT1078I/LT1079I
LT1078AM/LT1079AM
LT1078M/LT1079M
MIN
TYP
MAX MIN
TYP
MAX
CONDITIONS
UNITS
LT1078
LT1078IS8/LT1079
LT1079ISW
●
●
●
70
80
250
280
95
100
100
370
400
560
μV
μV
μV
●
●
●
0.4
1.8
LT1078IS8
LT1079ISW
0.5
0.6
0.7
2.5
3.5
4.0
μV/°C
μV/°C
μV/°C
●
●
0.07
0.50
LT1078I/LT1079I
0.07
0.1
0.70
1.0
nA
nA
●
7
10
7
12
nA
IB
Input Bias Current
CMRR
Common Mode Rejection Ratio VCM = 0.05V to 3.2V
●
92
106
88
104
dB
PSRR
Power Supply Rejection Ratio
VS = 3.1V to 12V
●
98
110
94
110
dB
AVOL
Large-Signal Voltage Gain
VO = 0.05V to 4V, No Load
VO = 0.05V to 3.5V, RL = 50k
●
●
110
80
600
400
80
60
600
400
V/mV
V/mV
Maximum Output Voltage
Swing
Output Low, No Load
Output Low, ISINK = 100μA
●
●
Output High, No Load
Output High, 2k to GND
●
●
IS
4.5
125
3.9
3.0
●
Supply Current per Amplifier
8
170
4.2
3.7
43
4.5
125
3.9
3.0
60
8
170
4.2
3.7
45
mV
mV
V
V
70
μA
The ● denotes the specifications which apply over the temperature range 0°C ≤ TA ≤ 70°C. VS = 5V, 0V, VCM = 0.1V, VO = 1.4V
unless otherwise noted.
SYMBOL PARAMETER
LT1078C/LT1079C
LT1078AC/LT1079AC
LT1078S8/LT1079SW
MIN
TYP
MAX MIN
TYP
MAX
CONDITIONS
UNITS
LT1078
LT1079
LT1078S8
LT1079SW
●
●
●
●
50
60
150
180
60
70
85
90
240
270
350
480
μV
μV
μV
μV
●
●
●
0.4
1.8
LT1078S8
LT1079SW
0.5
0.6
0.7
2.5
3.5
4.0
μV/°C
μV/°C
μV/°C
Input Offset Current
●
0.06
0.35
0.06
0.50
nA
IB
Input Bias Current
●
6
9
6
11
nA
CMRR
Common Mode Rejection Ratio VCM = 0V to 3.4V
●
94
108
90
106
dB
PSRR
Power Supply Rejection Ratio
VS = 2.6V to 12V
●
100
112
97
112
dB
AVOL
Large-Signal Voltage Gain
VO = 0.05V to 4V, No Load
VO = 0.05V to 3.5V, RL = 50k
●
●
150
110
750
500
110
80
750
500
V/mV
V/mV
Maximum Output Voltage
Swing
Output Low, No Load
Output Low, ISINK = 100μA
●
●
Output High, No Load
Output High, 2k to GND
●
●
VOS
Input Offset Voltage
ΔVOS
ΔT
Input Offset Voltage Drift
(Note 6)
IOS
IS
Supply Current per Amplifier
●
4.0
105
4.1
3.3
7
150
4.3
3.8
40
4.0
105
4.1
3.3
55
7
150
4.3
3.8
42
mV
mV
V
V
63
μA
10789fe
4
LT1078/LT1079
ELECTRICAL CHARACTERISTICS
SYMBOL PARAMETER
VOS
Input Offset Voltage
IOS
Input Offset Current
IB
Input Bias Current
VS = ±15V, TA = 25°C unless otherwise noted.
LT1078AC/LT1079AC
LT1078AM/LT1079AM
MIN
TYP
MAX
CONDITIONS
(Including LT1078IS8/LT1078S8)
LT1079ISW/LT1079SW
Input Voltage Range
LT1078C/LT1079C
LT1078I/LT1079I
LT1078M/LT1079M
LT1078S8/LT1079SW
MIN
TYP
MAX
UNITS
50
250
70
80
350
500
μV
μV
0.05
0.25
0.05
0.35
nA
6
8
6
10
nA
13.5
–15.0
13.8
–15.3
13.5
–15.0
13.8
–15.3
V
V
100
114
97
114
dB
CMRR
Common Mode Rejection Ratio VCM = 13.5V, –15V
PSRR
Power Supply Rejection Ratio
VS = 5V, 0V to ±18V
102
114
100
114
dB
AVOL
Large-Signal Voltage Gain
VO = ±10V, RL = 50k
VO = ±10V, RL = 2k
1000
400
5000
1100
1000
300
5000
1100
V/mV
V/mV
VOUT
Maximum Output Voltage
Swing
RL = 50k
RL = 2k
±13.0
±11.0
±14.0
±13.2
±13.0
±11.0
±14.0
±13.2
V
V
SR
Slew Rate
0.06
0.10
0.06
0.10
V/μs
IS
Supply Current per Amplifier
46
65
47
μA
75
The ● denotes the specifications which apply over the temperature range – 40°C ≤ TA ≤ 85°C for I grades, – 55°C ≤ TA ≤ 125°C for
AM/M grades. VS = ±15V unless otherwise noted.
SYMBOL PARAMETER
VOS
Input Offset Voltage
ΔVOS
ΔT
Input Offset Voltage Drift
(Note 6)
IOS
Input Offset Current
LT1078I/LT1079I
LT1078AM/LT1079AM
LT1078M/LT1079M
MIN
TYP
MAX MIN
TYP
MAX
CONDITIONS
UNITS
(Including LT1078IS8)
LT1079ISW
●
●
90
430
120
130
600
825
μV
μV
●
●
●
0.5
1.8
LT1078IS8
LT1079ISW
0.6
0.7
0.8
2.5
3.8
5.0
μV/°C
μV/°C
μV/°C
●
●
0.07
0.50
LT1078I/LT1079I
0.07
0.1
0.70
1.0
nA
nA
●
7
10
7
12
nA
IB
Input Bias Current
AVOL
Large-Signal Voltage Gain
VO = ±10V, RL = 5k
●
200
700
150
700
V/mV
CMRR
Common Mode Rejection Ratio VCM = 13V, –14.9V
●
94
110
90
110
dB
PSRR
Power Supply Rejection Ratio
●
98
110
94
110
dB
Maximum Output Voltage Swing RL = 5k
●
±11.0
±13.5
±11.0
±13.5
V
Supply Current per Amplifier
●
IS
VS = 5V, 0V to ±18V
52
80
54
95
μA
10789fe
5
LT1078/LT1079
ELECTRICAL CHARACTERISTICS
0°C ≤ TA ≤ 70°C. VS = ±15V unless otherwise noted.
SYMBOL PARAMETER
VOS
The ● denotes the specifications which apply over the temperature range
LT1078AC/LT1079AC
MIN
TYP
MAX
CONDITIONS
LT1078C/LT1079C
LT1078S8/LT1079SW
MIN
TYP
MAX
UNITS
●
●
●
70
330
LT1078S8
LT1079SW
90
100
115
460
540
750
μV
μV
μV
●
●
●
0.5
1.8
LT1078S8
LT1079SW
0.6
0.7
0.8
2.5
3.8
5.0
μV/°C
μV/°C
μV/°C
Input Offset Voltage
ΔVOS
ΔT
Input Offset Voltage Drift
(Note 6)
IOS
Input Offset Current
●
0.06
0.35
0.06
0.50
nA
IB
Input Bias Current
●
6
9
6
11
nA
AVOL
Large-Signal Voltage Gain
VO = ±10V, RL = 5k
●
CMRR
Common Mode Rejection Ratio
VCM = 13V, –15V
●
97
112
94
112
dB
PSRR
Power Supply Rejection Ratio
VS = 5V, 0V to ±18V
●
100
112
97
112
dB
Maximum Output Voltage Swing
RL = 5k
● ±11.0
±13.6
±11.0
±13.6
V
IS
Supply Current per Amplifier
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: Typical parameters are defined as the 60% yield of parameter
distributions of individual amplifiers, i.e., out of 100 LT1079s (or 100
LT1078s) typically 240 op amps (or 120) will be better than the indicated
specification.
Note 3: This parameter is tested on a sample basis only. All noise
parameters are tested with VS = ±2.5V, VO = 0V.
●
300
1200
49
250
73
1200
50
V/mV
μA
85
Note 4: This parameter is guaranteed by design and is not tested.
Note 5: Power supply rejection ratio is measured at the minimum supply
voltage. The op amps actually work at 1.8V supply but with a typical offset
skew of –300μV.
Note 6: This parameter is not 100% tested.
10789fe
6
LT1078/LT1079
U W
TYPICAL PERFORMANCE CHARACTERISTICS
Input Bias and Offset Currents
vs Temperature
VS = ±15V
45
100
–5
Input Bias Current
vs Common Mode Voltage
0
VS = 5V, 0V TO ±15V
VS = 5V, 0V
–2
IOS
50
INPUT BIAS CURRENT (nA)
50
OFFSET CURRENT (pA)
SUPPLY CURRENT PER AMPLIFIER (μA)
55
BIAS CURRENT (nA)
Supply Current vs Temperature
0
40
VS = 5V, 0V
35
30
25
–50 –25
50
25
75
0
TEMPERATURE (°C)
100
IB
–6
TA = 25°C
–6
TA = 125°C
–8
–10
–12
–7
–50 –25
125
TA = –55°C
–4
50
25
0
75
TEMPERATURE (°C)
100
–1
125
LT1078/79 • TPC03
LT1078/79 • TPC02
LT1078/79 • TPC01
0.1Hz to 10Hz Noise
4
0
1
2
3
COMMON MODE VOLTAGE (V)
0.01Hz to 10Hz Noise
Noise Spectrum
1000
CHANNEL B
VOLTAGE NOISE DENSITY (nV/√Hz)
CURRENT NOISE DENSITY (fA/√Hz)
TA = 25°C
VS = ±2.5V
CHANNEL A
NOISE VOLTAGE (0.4μV/DIV)
NOISE VOLTAGE (0.4μV/DIV)
TA = 25°C
VS = ±2.5V
CHANNEL A
0.4μV
CHANNEL B
0
2
6
4
TIME (SEC)
8
20
0
10
60
40
TIME (SEC)
80
10Hz Voltage Noise Distribution
15
10
5
0
35
30
VOLTAGE NOISE DENSITY (nV/√Hz)
1/f CORNER
0.7Hz
40
LT1078/79 • TPC07
1
100
10
FREQUENCY (Hz)
15
10
0
1000
Long Term Stability of Two
Representative Units (LT1078)
15
120
VS = 5V, 0V
109
VCM = 0.1V
120 LT1078'S
70 LT1079'S 89
520 OP AMPS
85
44
47
5
25
30
LT1078/79 • TPC06
OFFSET VOLTAGE CHANGE (μV)
PERCENT OF UNITS
PERCENT OF UNITS
20
106 LT1078'S
45 LT1079'S
20
VOLTAGE
NOISE
10
0.1
100
25
35
25
100
Distribution of Offset Voltage Drift
with Temperature (In All Packages
Except Surface Mount)
TA = 25°C
VS = ± 2.5V
329 OP AMPS TESTED
FROM THREE RUNS
CURRENT
NOISE
LT1078/79 • TPC05
LT1078/79 • TPC04
30
300
TA = 25°C
VS = ±2.5V
(AT VS = ±15V
VOLTAGE NOISE
IS 4% LESS
CURRENT NOISE
IS UNCHANGED)
1
7
3 5
4 3
1
1
1
–2
–1
0
1
2
OFFSET VOLTAGE DRIFT WITH TEMPERATURE (μV/°C)
LT1078/79 • TPC08
TA = 25°C, VS = 5V, 0V
VCM = 0.1V
10
1A
5
0
2B
–5
1B
–10
2A
–15
0
1
2
3
TIME (MONTHS)
4
5
LT078/79 • TPC09
10789fe
7
LT1078/LT1079
U W
TYPICAL PERFORMANCE CHARACTERISTICS
Voltage Gain vs Frequency
Gain, Phase vs Frequency
140
30
VS = 5V, 0V
40
±15V
5V, 0V
GAIN
10
20
140
PHASE
MARGIN
54°
160
5V, 0V
0
100
10 100 1k 10k 100k 1M
FREQUENCY (Hz)
10
30
AV = 1
60
AV = 5
40
AV = 10
20
0
–10
1
80
200
TA = 25°C
CL = 20pF
–20
0.01 0.1
100
300
FREQUENCY (kHz)
10
1000
100
1000
CAPACITIVE LOAD (pF)
10000
LT1078/79 • TPC12
LT1078/79 • TPC10
LTC1078/79 TPC11
Slew Rate, Gain Bandwidth
Product and Phase Margin vs
Temperature
Large-Signal Transient Response
VS = 5V, 0V
Large-Signal Transient Response
VS = ±15V
0.12
SLEW = ±15V
0.10
SLEW = 5V, 0V
φM = ±15V
0.04
70
φM = 5V, 0V
60
50
240
GBW = ±15V
220
40
5V/DIV
80
0.06
1V/DIV
0.08
PHASE MARGIN (DEG)
SLEW RATE (V/μs)
180
±15V
0
TA = 25°C
VS = 5V, 0V
120
PHASE SHIFT (DEG)
VOLTAGE GAIN (dB)
20
80
60
100
OVERSHOOT (%)
VS = ±15V
100
VOLTAGE GAIN (dB)
PHASE
MARGIN
66°
TA = 25°C
120
GAIN BANDWIDTH
PRODUCT (kHz)
Capacitive Load Handling
120
0V
0V
200
180
fO = 20kHz
160
–50 –25
AV = 1
NO LOAD
AV = 1, NO LOAD
50μs/DIV
INPUT PULSE 0V TO 3.8V
GBW = 5V, 0V
100μs/DIV
LT1078/79 • TPC28
LT1078/79 • TPC27
50
25
0
75
TEMPERATURE (°C)
100
125
LT1078/79 • TPC13
Minimum Supply Voltage
Warm-Up Drift
125°C
–100
70°C
–200
0°C
25°C
–300
–55°C
NONFUNCTIONAL
–400
–500
0
2
3
1
POSITIVE SUPPLY VOLTAGE (V)
LT1078/79 • TPC16
TA = 25°C
VS = ±15V
WARM UP DRIFT
AT VS = 5V, 0V IS
IMMEASURABLY LOW
0.7
0.6
0.5
0.4
0.3
VS = ±15V
VS = 5V, 0V
125°C
VOLTAGE GAIN (V/V)
V – = 0V
–0.1V ≤ VCM ≤ 0.4V
0
Voltage Gain vs Load Resistance
10M
0.8
CHANGE IN OFFSET VOLTAGE (μV)
INPUT OFFSET VOLTAGE (μV)
100
LT1079
1M
25°C
–55°C
–55°C
25°C
125°C
0.2
LT1078
0.1
0
0
1
2
3
TIME AFTER POWER-ON (MINUTES)
LT1078/79 • TPC17
100k
100
1k
10k
100k
LOAD RESISTANCE TO GROUND (Ω)
1M
LT1078/79 • TPC18
10789fe
8
LT1078/LT1079
U W
TYPICAL PERFORMANCE CHARACTERISTICS
Output Saturation vs Temperature
vs Sink Current
Output Voltage Swing
vs Load Current
V+
1000
16
ISINK = 2mA
ISINK = 10μA
VS = 5V, 0V
ISINK = 1μA
10
NO LOAD
–55°C
+
V –2
V– + 2
125°C
V– + 1
12
10
8
6
4
25°C
2
RL = 5k TO GND
1
–50 –25
TA = 25°C
VS = 5V, 0V
14
V+ – 1
PERCENT OF UNITS
ISINK = 1mA
ISINK = 100μA
100
25°C
125°C
OUTPUT VOLTAGE SWING (V)
SATURATION VOLTAGE (mV)
Distribution of Input Offset Voltage
(LT1078 in 8-Pin SO Package)
V
0
25
50
75
TEMPERATURE (°C)
100
–55°C
–
0
40 80 120 160
–160 –120 –80 –40 0
INPUT OFFSET VOLTAGE (μV)
0.01
0.1
1
10
SOURCING OR SINKING LOAD CURRENT (mA)
125
LT1078/79 • TPC20
LT1078/79 • TPC19
LT1078/79 • TPC21
V+ – 1
V+ – 2
V– + 1
V–
V– – 1
–50 –25
0
25
50
75
TEMPERATURE (°C)
100
125
Closed Loop Output Impedance
VS = ±15V
RL ≥ 100k
5
VS = 5V, 0V
RL ≥ 100k
20
VS = 5V, 0V
RL ≥ 1k
4
VS = ±15V
RL = 30k
3
10
2
TA = 25°C
LOAD RL,
TO GND
0
0.01
1
0
100
1
10
FREQUENCY (kHz)
1k
OUTPUT IMPEDANCE (Ω)
COMMON MODE RANGE (V)
V + = 2.5V TO 18V
V – = 0V TO –18V
30
PEAK-TO-PEAK OUTPUT SWING, VS = 5V, 0V (V)
V+
Undistorted Output Swing
vs Frequency
PEAK-TO-PEAK OUTPUT SWING, VS = ±15V (V)
Common Mode Range
vs Temperature
AV = 100
100
AV = 10
10
AV = 1
1
0.1
10
100
1k
10k
FREQUENCY (Hz)
LT1078/79 • TPC23
LT1078/79 • TPC24
LT1078/79 • TPC22
Common Mode Rejection Ratio
vs Frequency
Power Supply Rejection Ratio
vs Frequency
100
VS = ±15V
80
VS = 5V, 0V
60
40
20
0
10
100
1k
10k
FREQUENCY (Hz)
100k
1M
LT1078/79 • TPC25
Channel Separation vs Frequency
120
140
100
120
80
NEGATIVE
SUPPLY
60
CHANNEL SEPARATION (dB)
TA = 25°C
POWER SUPPLY REJECTION RATIO (dB)
COMMON MODE REJECTION RATIO (dB)
120
POSITIVE
SUPPLY
40
20
0
0.1
100k
100
80
60
40
TA = 25°C
VS = ±2.5V
VIN = 3VP-P TO 2kHz
RL = 10k
20
TA = 25°C
VS = ±2.5V + 1VP-P SINE WAVE
0
1
10
100 1k
10k
FREQUENCY (Hz)
100k
1M
LT1078/79 • TPC26
1
10
10k
1k
100
FREQUENCY (Hz)
100k
1M
LT1078/79 • TPC27
10789fe
9
LT1078/LT1079
U W
TYPICAL PERFORMANCE CHARACTERISTICS
Small-Signal Transient Response
VS = 5V, 0V
20mV/DIV
20mV/DIV
Small-Signal Transient Response
VS = ± 2.5V
0.1V
AV = 1
10μs/DIV
CL = 15pF
INPUT 50mV TO 150mV
0V
AV = 1
CL = 15pF
LT1078/79 • TPC24
10μs/DIV
LT1078/79 • TPC25
20mV/DIV
Small-Signal Transient Response
VS = ± 15V
0V
AV = 1
CL = 15pF
10μs/DIV
LT1078/79 • TPC26
U
W
U
U
APPLICATIONS INFORMATION
The LT1078/LT1079 devices are fully specified with
V + = 5V, V – = 0V, VCM = 0.1V. This set of operating
conditions appears to be the most representative for
battery-powered micropower circuits. Offset voltage is
internally trimmed to a minimum value at these supply
voltages. When 9V or 3V batteries or ±2.5V dual supplies
are used, bias and offset current changes will be minimal.
Offset voltage changes will be just a few microvolts as
given by the PSRR and CMRR specifications. For example,
if PSRR = 114dB (= 2μV/V), at 9V the offset voltage change
will be 8μV. Similarly, VS = ±2.5V, VCM = 0V is equivalent
to a common mode voltage change of 2.4V or a VOS
change of 7μV if CMRR = 110dB (3μV/V).
A full set of specifications is also provided at ±15V supply
voltages for comparison with other devices and for completeness.
Single Supply Operation
The LT1078/LT1079 are fully specified for single supply
operation, i.e., when the negative supply is 0V. Input
common mode range goes below ground and the output
swings within a few millivolts of ground while sinking
current. All competing micropower op amps either cannot
swing to within 600mV of ground (OP-20, OP-220, OP-420)
or need a pull-down resistor connected to the output to swing
to ground (OP-90, OP-290, OP-490, HA5141/42/44). This
10789fe
10
LT1078/LT1079
U
W
U
U
APPLICATIONS INFORMATION
difference is critical because in many applications these
competing devices cannot be operated as micropower op
amps and swing to ground simultaneously.
As an example, consider the instrumentation amplifier
shown on the front page. When the common mode signal
is low and the output is high, amplifier A has to sink
current. When the common mode signal is high and the
output low, amplifier B has to sink current. The competing
devices require a 12k pull-down resistor at the output of
amplifier A and a 15k at the output of B to handle the
specified signals. (The LT1078 does not need pull-down
resistors.) When the common mode input is high and the
output is high these pull-down resistors draw 300μA (150μA
each), which is excessive for micropower applications.
The instrumentation amplifier is by no means the only
application requiring current sinking capability. In seven
of the nine single supply applications shown in this data
sheet the op amps have to be able to sink current. In two
of the applications the first amplifier has to sink only the
6nA input bias current of the second op amp. The competing devices, however, cannot even sink 6nA without a pulldown resistor
Since the output of the LT1078/LT1079 cannot go exactly
to ground, but can only approach ground to within a few
millivolts, care should be exercised to ensure that the
output is not saturated. For example, a 1mV input signal
will cause the amplifier to set up in its linear region in the
gain 100 configuration shown in Figure 1a, but is not
enough to make the amplifier function properly in the
voltage follower mode, Figure 1b.
5V
5V
R
–
99R
+
1mV
LT1078/79 • F01a
Figure 1a. Gain 100 Amplifier
100mV
1mV
+
LT1078/79 • F01a
Figure 1b. Voltage Follower
1. When the input is more than a diode drop below ground,
unlimited current will flow from the substrate (V –
terminal) to the input. This can destroy the unit. On the
LT1078/LT1079, resistors in series with the input protect
the devices even when the input is 5V below ground.
2. When the input is more than 400mV below ground (at
25°C), the input stage saturates and phase reversal
occurs at the output. This can cause lockup in servo
systems. Due to a unique phase reversal protection circuitry, the LT1078/LT1079 output does not reverse, as
illustrated in Figure 2, even when the inputs are at –1V.
4V
2V
2V
2V
0V
0V
0V
1ms/DIV
OP-90 EXHIBITS OUTPUT PHASE REVERSAL
LT1078/79 • F02a
99R
Single supply operation can also create difficulties at the
input. The driving signal can fall below 0V — inadvertently
or on a transient basis. If the input is more than a few
hundred millivolts below ground, two distinct problems
can occur on previous single supply designs, such as the
LM124, LM158, OP-20, OP-21, OP-220, OP-221, OP-420
(1 and 2), OP-90/290/490 (2 only):
4V
1ms/DIV
–
100mV
4V
6VP-P INPUT
–1V TO 5V
R
1ms/DIV
LT1078/LT1079 NO PHASE REVERSAL
LT1078/79 • F02b
LT1078/79 • F02C
Figure 2. Voltage Follower with Input Exceeding the Negative Common Mode Range (VS = 5V, 0V)
10789fe
11
LT1078/LT1079
U
W
U
U
APPLICATIONS INFORMATION
Matching Specifications
In many applications the performance of a system depends on the matching between two op amps, rather than
the individual characteristics of the two devices. The two
and three op amp instrumentation amplifier configurations shown in this data sheet are examples. Matching
characteristics are not 100% tested on the LT1078/LT1079.
Some specifications are guaranteed by definition. For
example, 70μV maximum offset voltage implies that mismatch cannot be more than 140μV. 97dB (= 14μV/V)
CMRR means that worst-case CMRR match is 91dB
(= 28μV/V). However, Table 1 can be used to estimate the
expected matching performance at VS = 5V, 0V between
the two sides of the LT1078, and between amplifiers A and
D, and between amplifiers B and C of the LT1079.
Table 1
PARAMETER
VOS Match, ΔVOS
LT1078
LT1079
Temperature Coefficient ΔVOS
Average Noninverting IB
Match of Noninverting IB
CMRR Match
PSRR Match
LT1078AC/LT1079AC/LT1078AM/LT1079AM
50% YIELD
98% YIELD
30
110
40
150
0.5
1.2
6
8
0.12
0.4
120
100
117
105
LT1078C/LT1079C/LT1078M/LT1079M
50% YIELD
98% YIELD
50
190
50
250
0.6
1.8
6
10
0.15
0.5
117
97
117
102
UNITS
μV
μV
μV/°C
nA
nA
dB
dB
Comparator Applications
The single supply operation of the LT1078/LT1079 and its
ability to swing close to ground while sinking current
lends itself to use as a precision comparator with TTL
compatible output.
4
OUTPUT (V)
2
2
0
0
0
100
–100
INPUT (mV)
INPUT (mV)
OUTPUT (V)
4
VS = 5V, 0V
200μs/DIV
0
VS = 5V, 0V
200μs/DIV
LT2078/79 • F03
LT2078/79 • F04
Figure 3. Comparator Rise Response
Time to 10mV, 5mV, 2mV Overdrives
Figure 4. Comparator Fall Response
Time to 10mV, 5mV, 2mV Overdrives
10789fe
12
LT1078/LT1079
U
TYPICAL APPLICATIONS
Micropower, 10ppm/°C, ±5V Reference
2M
LT1034BC-1.2
Gain of 10 Difference Amplifier
10M
9V
3V
220k
5.000VOUT
120k 3
+
–
1M
–
–IN
8
1/2 LT1078
2
1M
1
510k
4
–9V
1M
6
7
–5.000VOUT
+
OUTPUT
0.0035V TO 2.4V
+
+IN
–
1/2 LT1078
5
1/2 LT1078
1M
LT1078/79 • TA04
10M
LT1078/79 • TA03
510k
1%
BANDWIDTH= 20kHz
OUTPUT OFFSET= 0.7mV
OUTPUT NOISE= 80μVP-P (0.1Hz TO 10Hz)
260μVRMS OVER FULL
BANDWIDTH
20k
160k
1% SUPPLY CURRENT = 9V BATTERY = 115μA
–9V BATTERY = 85μA
OUTPUT NOISE = 36μVP-P, 0.1Hz TO 10Hz
THE USEFULNESS OF DIFFERENCE AMPLIFIERS IS LIMITED BY
THE FACT THAT THE INPUT RESISTANCE IS EQUAL TO THE SOURCE
RESISTANCE. THE PICOAMPERE OFFSET CURRENT AND LOW
CURRENT NOISE OF THE LT1078 ALLOWS THE USE OF 1M SOURCE
RESISTORS WITHOUT DEGRADATION IN PERFORMANCE. IN ADDITION,
WITH MEGOHM RESISTORS MICROPOWER OPERATION CAN BE MAINTAINED
THE LT1078 CONTRIBUTES LESS THAN 3% OF THE TOTAL OUTPUT NOISE AND
DRIFT WITH TIME AND TEMPERATURE. THE ACCURACY OF THE –5V OUTPUT
DEPENDS ON THE MATCHING OF THE TWO 1M RESISTORS
Picoampere Input Current, Triple Op Amp Instrumentation Amplifier with Bias Current Cancellation
3
–IN
+
1/4 LT1079
2
1
R2
1M
R1
1M
–
2R
20M
R3
9.1M
RG
200k
9
6
–
1/4 LT1079
5
+IN
R
10M
12
2R
20M
+
+
9V
4
–
11
14
–
1/4 LT1079
10
R2
1M
1/4 LT1079
13
7
R1
1M
+
8
OUTPUT
4mV TO 8.2V
LT`1078/79 • TA05
R3
9.1M
(
)
GAIN = 1 + 2R1 R3 = 100 FOR VALUES SHOWN
RG R2
INPUT BIAS CURRENT TYPICALLY < 150pA
INPUT RESISTANCE = 3R = 30M FOR VALUES SHOWN
NEGATIVE COMMON MODE LIMIT = (IB)(2R) + 20mV ≈ 140mV
GAIN BANDWIDTH PRODUCT = 1.8MHz
10789fe
13
LT1078/LT1079
U
TYPICAL APPLICATIONS
85V, –100V Common Mode Range
Instrumentation Amplifier (AV = 10)
Half-Wave Rectifier
2M
1M
9V
10M
+IN
10M
–IN
2
–
10M
1/2 LT1078
3
+
1M
3V
2M
8
–
INPUT
100k
1
100k
4
6
–
1/2 LT1078
5
–9V
7
+
OUTPUT
1/2 LT1078
1M
OUTPUT
8V TO –9V
+
VOMIN = 6mV
NO DISTORTION TO 100Hz
LT1078/79 • TA06
1.8V
BANDWIDTH=
OUTPUT OFFSET=
OUTPUT NOISE=
=
2kHz
8mV
0.8mVP-P (0.1Hz TO 10Hz)
1.4mVRMS OVER FULL BANDWIDTH
(DOMINATED BY RESISTOR NOISE)
INPUT RESISTANCE = 10M
1.8V
0V
–1.8V
LT1078/79 • TA07
Absolute Value Circuit (Full-Wave Rectifier)
200k
200k
INPUT
2
5V
3.5V
8
0V
–
1/2 LT1078
3
3.5V
1
5
1N4148
+
+
7
1/2 LT1078
4
6
OUTPUT
–
–3.5V
LT1078/79 • TA08
VOMIN = 4mV
NO DISTORTION TO 100Hz
Programmable Gain Amplifier (Single Supply)
1.11k
10k
100k
1M
3V TO 18V
2
–
1/4 LT1079
3
+
3V TO 18V
11
4
11
1
1
6
2
–
1/4 LT1079
5
13
A
7
+
9
10
ERROR DUE TO SWITCH ON RESISTANCE,
LEAKAGE CURRENT, NOISE AND TRANSIENTS
ARE ELIMINATED
1/4 LT1079
12
+
–
+
C
8 8
7
CD4016B
13
5
6
GAIN
1000
100
10
14
OUT
LT1078/79 • TA09
9
1/4 LT1079
IN
4
3 B
–
PIN 13
HIGH
LOW
LOW
CD4016B
PIN 5
LOW
HIGH
LOW
PIN 6
LOW
LOW
HIGH
10789fe
14
LT1078/LT1079
U
TYPICAL APPLICATIONS
Single Supply, Micropower, Second Order Lowpass Filter with 60Hz Notch
0.02μF
27.6k
0.1%
27.6k
0.1%
3
IN
+
0.01μF
6
5V
8
1
1/2 LT1078
2
–
2.64M
0.1%
2.64M
0.1%
–
7
1/2 LT1078
5
+
OUTPUT
TYPICAL OFFSET
≈ 600μV
2000pF
0.5%
4
5.1M
1%
120k
5%
1.35M
0.1%
100pF
1000pF
0.5%
1000pF
0.5%
fC = 40Hz
Q > 30
LT1078/79 • TA10
Micropower Multiplier/Divider
505k
0.1%
505k
0.1%
–
220pF
4
1/4 LT1079
5
30k
5%
11
Z INPUT
(5mV TO 50V)
220pF
Q3
30k
5%
7
+
Q1
14
10k
GAIN
499k
0.5%
13
1/4 LT1079
+
9V
6
–
Y INPUT
(5mV TO 50V)
12
–1.5V TO –9V
X INPUT
(5mV TO 50V)
505k
0.1%
2
–
+
–
10
+
220pF
Q2
1/4 LT1079
3
9
Q4
1/4 LT1079
8
OUTPUT
(5mV TO 8V)
1
30k
5%
LT1078/79 • TA11
Q1,Q2, Q3, Q4 = MAT-04
TYPICAL LINEARITY = 0.01% OF FULL-SCALE OUTPUT
(X)(Y)
OUTPUT =
, POSITIVE INPUTS ONLY
(Z)
X + Y+ Z + OUT
500k
OUT
POSITIVE SUPPLY CURRENT = 165μA +
500k
NEGATIVE SUPPLY CURRENT = 165μA +
BANDWIDTH (< 3VP-P SIGNAL): X AND Y INPUTS = 10kHz
Z INPUT = 4kHz
10789fe
15
LT1078/LT1079
U
TYPICAL APPLICATIONS
Micropower Dead Zone Generator
Q4
1M**
2
INPUT
VSET
DEAD ZONE
CONTROL INPUT
0.4V TO 5V
1M*
1M**
–
Q2
Q3
1
470k
1/4 LT1079
510k
3
+
1M*
Q1
2N4393
9
1M**
GAIN
200k
–
8
1M
1M**
13
–
510k
12
+
1/4 LT1079
1N914
10
+
1/4 LT1079
14
VOUT
LT1078/79 • TA12
9V
6
–
1M
4
+
1N914
Q6
2N4393
VSET
VOUT
1000pF
7
1/4 LT1079
5
680k
510k
1M
Q5
11
–9V
VIN
BIPOLAR SYMMETRY IS EXCELLENT
VSET
BECAUSE ONE DEVICE, Q2,
* 1% FILM
SETS BOTH LIMITS
** RATIO MATCH 0.05%
SUPPLY CURRENT ≈ 240μA
Q2, Q3, Q4, Q5 CA3096 TRANSISTOR ARRAY
BANDWIDTH = 150kHz
10789fe
16
LT1078/LT1079
U
TYPICAL APPLICATIONS
Lead-Acid Low-Battery Detector with System Shutdown
BATTERY
OUTPUT
2M
1%
2M
1%
910k
5%
3
12V
+
1
1/2 LT1078
2
LO = BATTERY LOW
(IF VS < 10.90V)
–
5
8
+
1/2 LT1078
255k
1%
6
280k
1%
–
LO = SYSTEM SHUTDOWN
(IF VS < 10.05V)
7
4
LT1004-1.2
LT1078/79 • TA13
TOTAL SUPPLY CURRENT = 105μA
Platinum RTD Signal Conditioner with Curvature Correction
3V (LITHIUM)
13k*
8
LT1004-1.2
1
+
–
12.3k*
3
10k*
1/2 LT1078
4
1μF
2
50k
5°C
TRIM
43.2k**
1k**
5k
220°C
TRIM
1k**
6
–
5
+
1/2 LT1078
RP = ROSEMOUNT 118MF
** = TRW MAR-6 0.1%
* = 1% METAL FILM
1k**
RP
1k AT
0°C
1μF
7
0.02V TO 2.2VOUT =
2°C TO 220°C ±0.1°C
1.21M*
(SELECT AT 110°C)
LT1078/79 • TA14
10789fe
17
LT1078/LT1079
W
W
SI PLIFIED SCHEMATIC
1/2 LT1078, 1/4 LT1079
V+
10k
10k
2.2k
5.6k
11.5k
5k
3.6k
1.3k
Q54
1
Q16
Q6
Q5
Q14
Q15
2
1
Q32
Q52
Q47
Q37
Q29
Q3
Q46
Q30
Q24
Q4
1
V–
3
8.6k
4
Q11
C1
50pF
Q40
3k
Q25
Q12
Q35
Q26
C4
4pF
1
2.9k
30Ω
Q44
C5
2.5pF
Q27
IN +
600Ω
Q41
V+
OUT
IN –
12.5k
Q53
Q1
Q21
150k
Q18
Q28
Q2
Q22
600Ω
V+
Q31
C3
40pF
J1
Q36
Q33
Q48
Q19
Q50
Q42
Q49
Q39
Q9
Q23
Q10 Q17
C2
175pF
Q8
Q7
V+
Q43
Q38
5.35k
30Ω
1.35k
6.2k
700k
Q51
Q55
10k
Q34
6.2k
9.1k
Q45
Q20
700k
V–
LT1078/79 • SIMPLIFIED SCHEM
U
PACKAGE DESCRIPTIO
H Package
8-Lead TO-5 Metal Can (.230 Inch PCD)
(Reference LTC DWG # 05-08-1321)
0.335 – 0.370
(8.509 – 9.398)
DIA
0.305 – 0.335
(7.747 – 8.509)
0.040
(1.016)
MAX
0.027 – 0.045
(0.686 – 1.143)
45°TYP
0.028 – 0.034
(0.711 – 0.864)
0.050
(1.270)
MAX
SEATING
PLANE
0.010 – 0.045*
(0.254 – 1.143)
0.016 – 0.021**
(0.406 – 0.533)
0.230
(5.842)
TYP
0.165 – 0.185
(4.191 – 4.699)
GAUGE
PLANE
PIN 1
REFERENCE
PLANE
0.500 – 0.750
(12.700 – 19.050)
0.110 – 0.160
(2.794 – 4.064)
INSULATING
STANDOFF
*LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
0.016 – 0.024
**FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS
(0.406 – 0.610)
H8 (TO-5) 0.230 PCD 1197
OBSOLETE PACKAGE
10789fe
18
LT1078/LT1079
U
PACKAGE DESCRIPTIO
J8 Package
8-Lead CERDIP (Narrow .300 Inch, Hermetic)
(Reference LTC DWG # 05-08-1110)
0.300 BSC
(0.762 BSC)
CORNER LEADS OPTION
(4 PLCS)
0.015 – 0.060
(0.381 – 1.524)
0.023 – 0.045
(0.584 – 1.143)
HALF LEAD
OPTION
0.045 – 0.068
(1.143 – 1.727)
FULL LEAD
OPTION
0.008 – 0.018
(0.203 – 0.457)
0.405
(10.287)
MAX
0.005
(0.127)
MIN
0.200
(5.080)
MAX
8
6
7
5
0.025
(0.635)
RAD TYP
0.220 – 0.310
(5.588 – 7.874)
0° – 15°
1
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
0.045 – 0.065
(1.143 – 1.651)
0.014 – 0.026
(0.360 – 0.660)
0.100
(2.54)
BSC
2
3
4
0.125
3.175
MIN
J8 1298
J Package
14-Lead CERDIP (Narrow .300 Inch, Hermetic)
(Reference LTC DWG # 05-08-1110)
0.300 BSC
(0.762 BSC)
0.015 – 0.060
(0.381 – 1.524)
0.008 – 0.018
(0.203 – 0.457)
0.005
(0.127)
MIN
0.200
(5.080)
MAX
0.785
(19.939)
MAX
14
12
13
11
10
9
8
0.220 – 0.310
(5.588 – 7.874)
0.025
(0.635)
RAD TYP
0° – 15°
1
0.045 – 0.065
(1.143 – 1.651)
0.014 – 0.026
(0.360 – 0.660)
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
0.100
(2.54)
BSC
2
3
4
5
6
7
0.125
(3.175)
MIN
J14 1298
OBSOLETE PACKAGES
N8 Package
8-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510)
0.300 – 0.325
(7.620 – 8.255)
0.009 – 0.015
(0.229 – 0.381)
(
+0.035
0.325 –0.015
+0.889
8.255
–0.381
)
0.045 – 0.065
(1.143 – 1.651)
0.400*
(10.160)
MAX
0.130 ± 0.005
(3.302 ± 0.127)
0.065
(1.651)
TYP
8
7
6
5
1
2
3
4
0.255 ± 0.015*
(6.477 ± 0.381)
0.100
(2.54)
BSC
0.125
(3.175) 0.020
MIN (0.508)
MIN
0.018 ± 0.003
(0.457 ± 0.076)
N8 1098
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
10789fe
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LT1078/LT1079
U
PACKAGE DESCRIPTION
N Package
14-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510)
0.130 ± 0.005
(3.302 ± 0.127)
0.300 – 0.325
(7.620 – 8.255)
0.045 – 0.065
(1.143 – 1.651)
0.020
(0.508)
MIN
0.005
(0.125)
MIN 0.100
(2.54)
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
BSC
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
(
8.255
+0.889
–0.381
)
0.125
(3.175)
MIN
14
13
12
11
10
9
8
1
2
3
4
5
6
7
0.255 ± 0.015*
(6.477 ± 0.381)
0.065
(1.651)
TYP
0.009 – 0.015
(0.229 – 0.381)
+0.035
0.325 –0.015
0.770*
(19.558)
MAX
0.018 ± 0.003
(0.457 ± 0.076)
N14 1098
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
0.010 – 0.020
× 45°
(0.254 – 0.508)
0.008 – 0.010
(0.203 – 0.254)
0.053 – 0.069
(1.346 – 1.752)
0°– 8° TYP
0.016 – 0.050
(0.406 – 1.270)
0.014 – 0.019
(0.355 – 0.483)
TYP
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
0.189 – 0.197*
(4.801 – 5.004)
7
8
5
6
0.004 – 0.010
(0.101 – 0.254)
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
0.050
(1.270)
BSC
1
3
2
4
SO8 1298
SW Package
16-Lead Plastic Small Outline (Wide .300 Inch)
(Reference LTC DWG # 05-08-1620)
0.291 – 0.299**
(7.391 – 7.595)
0.093 – 0.104
(2.362 – 2.642)
0.010 – 0.029 × 45°
(0.254 – 0.737)
0.398 – 0.413*
(10.109 – 10.490)
0.037 – 0.045
(0.940 – 1.143)
16
15
14
13
12
11 10
9
0° – 8° TYP
0.009 – 0.013
(0.229 – 0.330)
0.050
(1.270)
BSC
NOTE 1
0.004 – 0.012
(0.102 – 0.305)
0.394 – 0.419
(10.007 – 10.643)
NOTE 1
0.014 – 0.019
(0.356 – 0.482)
TYP
0.016 – 0.050
(0.406 – 1.270)
NOTE:
1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
1
2
3
4
5
6
7
8
S16 (WIDE) 1098
10789fe
20
Linear Technology Corporation
LT/CPI 1201 1.5K REV E • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 1994