dm00037526

AN3978
Application note
Designing a digital output module
with the L6370Q intelligent power switch STEVAL-IFP020V1
Introduction
The L6370Q is a single channel high-side driver chip intended for driving resistive, inductive
or capacitive loads in industrial environments. It provides an embedded fast
demagnetization feature for inductive load switch-off. The chip evaluates load disconnection
(in channel ON state), output short connection to VCC or GND, overtemperature, supply
voltage undervoltage and provides feedback to a control unit. An integrated extensive set of
electrical protections makes the application safe and reliable for use in harsh conditions.
This application note documents an example of an application design with the L6370Q
component. It guides the user on how to choose application external components, provides
appropriate schematic diagrams and PCB design, and an overview of immunity test results.
Application main features
●
Galvanic isolated digital output module
●
Single channel topology
●
2.5 A output current
●
100 mΩ output MOSFET RDSON
●
9.5 V to 35 V supply voltage range
●
Output current limiting
●
Thermal shutdown
●
Open ground protection
●
Internal negative voltage clamping to VS - 50 V for fast demagnetization
●
Undervoltage lockout with hysteresis
●
Open load detection
●
Two diagnostic outputs
●
Output status LED indication
●
Non-dissipative short-circuit protection
●
Protection against surge pulses (IEC61000-4-5)
●
Immunity against burst transient (IEC61000-4-4)
●
ESD protection (IEC61000-4-2)
●
Compact design thanks to small component packages (L6370Q in QFN 7 x 7 mm)
December 2011
Doc ID 022179 Rev 1
1/19
www.st.com
Contents
AN3978
Contents
1
2
3
Schematic design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1
Input interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2
Diagnostic signal interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.3
Supply voltage line protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.4
Short-circuit current limit settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.5
ON-DELAY configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PCB layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1
Supply voltage filter layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2
Earth coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
EMC requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1
Description of the procedure to evaluate the robustness
of the L6370Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2
Burst tests (according to the IEC61000-4-4) . . . . . . . . . . . . . . . . . . . . . . 11
3.3
Surge test (according to the IEC61000-4-5) . . . . . . . . . . . . . . . . . . . . . . . 11
4
EMC testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6
Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Appendix A Demonstration board photo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Appendix B Bill of material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/19
Doc ID 022179 Rev 1
AN3978
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Application EFT (burst) robustness, applied to supply voltage lines. . . . . . . . . . . . . .
Application EFT (burst) robustness, applied to output lines . . . . . . . . . . . . . . . . . . . .
Application surge test results, surge applied to supply lines . . . . . . . . . . . . . . . . . . .
Application surge test results, surge applied to output lines . . . . . . . . . . . . . . . . . . . .
Bill of material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Doc ID 022179 Rev 1
. . . . 12
. . . . 12
. . . . 12
. . . . 13
. . . . 16
. . . . 18
3/19
List of figures
AN3978
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
4/19
Application schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input interface circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic signals circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply voltage protection filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Demonstration board PCB layout - top side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Demonstration board PCB layout - bottom side . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply voltage filter PCB design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Demonstration board - top view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Demonstration board - bottom view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Doc ID 022179 Rev 1
.....5
.....6
.....7
.....7
.....9
.....9
. . . . 10
. . . . 15
. . . . 15
AN3978
1
Schematic design
Schematic design
A complete application schematic diagram is visible in Figure 1.
Figure 1.
Application schematic diagram
Doc ID 022179 Rev 1
5/19
Schematic design
AN3978
Section 1.1 to Section 1.5 show how the L6370Q chip features are configured, which
external components are used, and how they are dimensioned.
1.1
Input interface
The aim of the design is to provide a galvanic isolated output module. It requires the use of
isolators on the control / feedback signals. In the case of STEVAL-IFP0020V1, cost
effective, compact size optocouplers (TLP281) have been selected.
Important parameters for the application design are:
●
Collector-emitter voltage higher than 80 V - which exceeds the L6370Q absolute
maximum ratings and therefore doesn't limit supply voltage range
●
Isolation voltage higher than 2500 Vrms - usually sufficient for this kind of application
●
Current transfer ratio (depends on LED current) - LED and output phototransistor
currents must be adjusted accordingly.
Figure 2.
).054
Input interface circuit
/04
2
2
6S
2
4,0 '.$?,OGIC
2
2
#
P&
6
'.$
'.$
)SOLATION
BARRIER
'.$
5
40
6S 6S 6S 6S
).
).
/54
/54
/54
/54
23#
/.$%,!9
$)!'
$)!'
/5434!45 3
'.$ 4! "
4! "
,1
!-
The input interface connection can be seen in Figure 2. LED current ranges between
approximately 2.4 mA, considering a 3.3 V signal level, and 4.3 mA for 5 V logic level.
Symmetrical LED resistor connection should positively influence EMC immunity. To achieve
the maximum tolerance of IN+ threshold (2 V according to the datasheet, considering that
IN- = 0 V), the required minimum phototransistor current is approximately 0.11 mA (2 V /
18 kΩ). This means that CTR of the optocoupler must be at least ~5% (0.11 mA / 2.4 mA).
This is in accordance with the TLP281 datasheet which shows a much higher CTR.
6/19
Doc ID 022179 Rev 1
AN3978
1.2
Schematic design
Diagnostic signal interface
The diagnostic signal interface is implemented in a similar way to the input interface. The
appropriate part of the schematic diagram can be seen in Figure 3.
Figure 3.
Diagnostic signals circuit
6?,OGIC
2
$)!'
6?,OGIC
/04
2
2
6S
40
4,0
'.$?,OGIC
/04
2
2
2
$)!'
5
6S
4,0
6S 6S 6S 6S
).
).
/54
/54
/54
/54
23#
/.$%,!9
$)!'
$)!'
/5434!45 3
'.$ 4! "
40
'.$?,OGIC
4! "
,1
)SOLATION
BARRIER
!-
In this case, the optocoupler LED current appears in the range from 1.3 mA to 5.2 mA
depending on supply voltage Vs. Symmetrical LED resistors are chosen in order to optimize
EMC immunity and split power dissipation. In order to comply with the logic levels on the
control side, an appropriate external pull-up resistor is necessary. The value selected for the
L6370Q application is 10 kΩ .
If the L6370Q open drain diagnostic driver is OFF, no current flows through the optocoupler
LED and the optotransistor is therefore OFF. Logic high level is provided by the
10 kΩ pull-up resistor.
If the diagnostic is active (ON), the optocoupler LED is powered and the optotransistor
conducts a current depending on a load. Minimum current to ensure TTL low level
compatibility (0.7 V max.) is:
(Vlogic - Vlmax) / PullUp = (5 V - 0.7 V) / 10000 = 0.43 mA. This condition is also in
accordance with TLP281 characteristics.
1.3
Supply voltage line protection
L6370Q supply voltage lines are protected against surges, reverse polarity and other
disturbances with the external filter, as shown in Figure 4.
Figure 4.
Supply voltage protection filter
40 6S
#.
40
#
N&
6
#
6
$
3-4!
!2+6! 0
'.$
!-
Doc ID 022179 Rev 1
7/19
Schematic design
AN3978
A Transil™ diode is used to clamp high energy surge pulses followed by a capacitive filter to
suppress noise disturbance and limit application EMI. Capacitor C1 (100 μF) has a low ESR
parameter in order to effectively suppress supply voltage fluctuations.
1.4
Short-circuit current limit settings
Configuration of the current limit is done by the external resistor connection between the
RSC pin and GND. A 470 Ω resistor is used in the STEVAL-IFP020V1 application to adjust
the maximum current limit, which is 3.2 A (typ.), due to the fact that 0 < RSC < 5 kΩ ,
according to the L6370Q datasheet.
1.5
ON-DELAY configuration
ON-DELAY pin functionality is well described in the L6370Q datasheet. Basically, it is used
to disable the power stage if an overcurrent condition lasts longer than the adjusted tON.
This feature also suppresses diagnostic activation in case of short-time overload or shortcircuit.
A capacitor value of 680 pF connected between the ON-DELAY and GND adjusts the
ON- DELAY time to:
tON = 1.28 * CON = 1.28 μs/pF * 680 pF = 870.4 μs
8/19
Doc ID 022179 Rev 1
AN3978
2
PCB layout
PCB layout
The demonstration board PCB layout has been developed by applying standard rules,
avoiding signal loops and minimizing track length.
Figure 5.
Demonstration board PCB layout - top side
Figure 6.
Demonstration board PCB layout - bottom side
Doc ID 022179 Rev 1
9/19
PCB layout
2.1
AN3978
Supply voltage filter layout
It is important to place the supply voltage filter components in the right order and make the
routes accordingly. A correct reference is visible in Figure 7.
Figure 7.
Supply voltage filter PCB design
The power supply is connected to CN3. The first component on the track should always be
a Transil diode (D1) in order to ensure a low-impedance path to the supply connector and to
minimize loop which may create electromagnetic disturbances. The next component is
a large bulk capacitor (C1). Its function is to cover energetic peaks during output current
transients and optimize EMI performance. The last stage of the filter is a ~100 nF ceramic
capacitor (C2). Points TP1 and TP2 are central reference points for power (Vs and GND)
distribution for the application.
2.2
Earth coupling
The board is equipped with a connection to earth protection line. Two high voltage coupling
capacitors - C3 and C4 (4.7 nF / 3 kV) are assembled on the board. It is recommended to
lead their connection tracks directly to power supply connector CN3 to suppress
charge/discharge current intervention of application reference supply points (TP1, TP2).
The charge/discharge currents are generated, for instance, by burst or surge noise in the
environment or during EMC tests.
10/19
Doc ID 022179 Rev 1
AN3978
EMC requirements
3
EMC requirements
3.1
Description of the procedure to evaluate the robustness of
the L6370Q
The reference to evaluate the robustness of the L6370Q product is the IEC61131-2
international standard. This international standard gives all the requirements and conditions
of tests that must be performed on the programmable logic controllers (PLC) and their
associated peripherals.
The IEC61131-2 standard specifies the Electromagnetic Compatibility (EMC) requirements
and the nature of the tests to perform in order to determine if the system meets these
requirements (paragraph 7: “Electromagnetic Compatibility EMC Requirements” and
paragraph 8: “Electromagnetic Compatibility (EMC) Type Tests and Verifications” of the Ed2
of the standard). The levels of each test depend on the zone where the system is installed.
The most typical industrial environmental levels correspond to zone B: local power
distribution zone and dedicated power distribution zone (see table 28: “EMC immunity
zones” of the IEC61131-2-Ed2 standard). The following paragraphs recall the test levels for
this zone.
3.2
Burst tests (according to the IEC61000-4-4)
The fast transient burst tests must be applied on all the input pins of the system.
A capacitive clamp-coupling device (50-200 pF) must be used as described in the
IEC61000-4-4 standard. The required burst voltage levels are: analog or digital I/O: +/-1 kV,
dc power line: +/-2 kV. The PLC system continues to operate as intended. Temporary
degradation of the performance is acceptable during the test, but the system must recover
by itself after the test (B criterion according to the IEC61131-2 standard).
3.3
Surge test (according to the IEC61000-4-5)
Since the voltage surge consists of a single but energetic pulse, the L6370Q device embeds
the appropriate protections. Moreover, additional external protection (filter) is necessary, see
Section 2.1 for an example. The absorbed energy complies at least with the requirements of
the IEC61131-2 standard. The high energy surge test must be applied on all output / supply
voltage terminals of the system. For all digital outputs and I/O power, the coupling method is
a 42 Ω serial resistance and a 0.5 μF capacitor. The required voltage surge levels are 0.5 kV
(line-to-line and line-to-earth coupling modes). The PLC system continues to operate as
intended. Temporary degradation of the performance is acceptable during the test, but the
system must recover by itself after the test (B criterion according to the IEC61131-2
standard).
Doc ID 022179 Rev 1
11/19
EMC testing
4
AN3978
EMC testing
The EMC requirements according to IEC61131-2 have been verified. Application tests
showed much better results than the requirements given by the industrial standard. The test
results are listed in the tables below. No additional protection devices have been used in the
application.
Table 1.
Application EFT (burst) robustness, applied to supply voltage lines
EFT test signal amplitude, test results at polarity (+ / -)
Configuration
1 kV
2 kV
3 kV
4 kV
5 kV
Standard demonstration board
configuration
A/A
A/A
A/A
B/B
B/B
Primary and secondary GNDs shorted
A/A
A/A
A/A
A/A
A/A
Table 2.
Application EFT (burst) robustness, applied to output lines
EFT test signal amplitude, test results at polarity (+ / -)
Configuration
1 kV
2 kV
3 kV
4 kV
5 kV
Standard demonstration board
configuration
A/A
A/A
A/A
B/B
B/B
Primary and secondary GNDs shorted
A/A
A/A
A/A
A/A
A/A
According to Table 1 and Table 2, it is clear that the chosen optical isolators functionality is
influenced by the burst noise. Therefore, performance criteria A is achieved with up to 3 kV
burst amplitude, the system then behaves according to criteria B.
A trial has been carried out and primary and secondary GNDs have been shorted in order to
limit common mode transients across the optical isolation. In this configuration the
performance criteria A is fulfilled also for higher burst amplitudes.
Therefore, the application designer should choose different isolators if a higher level of
immunity must be achieved. Selection should target isolators with a high CMR (“Common
Mode Rejection”) parameter.
Table 3.
Application surge test results, surge applied to supply lines
Surge test signal amplitude, test results at polarity (+ / -)
Configuration
Standard
demonstration
board configuration
12/19
Mode
1 kV
2 kV
3 kV
4 kV
Common (CM)
A/A
A/A
A/A
A/A
Differential (DM)
B/B
B/B
B/B
B/B
Doc ID 022179 Rev 1
AN3978
EMC testing
Table 4.
Application surge test results, surge applied to output lines
Surge test signal amplitude, test results at polarity (+ / -)
Configuration
Mode
Common (CM)
Standard
demonstration
board configuration Differential (DM)
1 kV
1.5 kV
2 kV
2.5 kV
3 kV
B/B
B/B
B/B
B/B
B/B
B/B
B/B
B/B
B/B
B/B
Table 3 and Table 4 indicate application surge immunity. Supply voltage and output ports
have been tested in common mode (CM) as well as in differential mode (DM). When surge
has been applied to supply lines in common mode, the application worked without any
influence, see Table 3. Differential mode influences the L6370Q operation due to the fact
that high energy surge pulses cause short-time power interruptions on the chip supply.
Immunity of the output in differential mode depends on the supply voltage capacitive filter.
Selection of the supply capacitor (C1) dramatically influences the achieved test result.
Practical tests showed that applications with a low ESR (0.074 Ω) 100 μF capacitor passed
3 kV successfully and failed at -3.5 kV. The same result has been achieved with a standard
220 μF SMD capacitor (ESR = 0.18 Ω). Applications with a standard 100 μF SMD (ESR =
0.34 Ω) capacitor usually failed at -2.5 kV, and with a 47 μF SMD capacitor (ESR = 0.68 Ω),
at -2 kV.
Doc ID 022179 Rev 1
13/19
Ordering information
5
AN3978
Ordering information
The application board is orderable in the same way as all STMicroelectronics products. The
appropriate ordering code is STEVAL-IFP020V1. It contains the application board
assembled according to the descriptions above, board documentation, PCB fabrication data
such as Gerber files, assembly files (Pick and Place), and component documentation.
6
Conclusion
This application note may be used as a guide when designing the L6370Q application.
The document shows that the L6370Q application works in harsh environments without any
problems and that the industrial standard requirements are fulfilled. Moreover, the test levels
are higher than requested for the majority of final products. The L6370Q application requires
a minimum amount of external components, which has a positive influence on the
application costs.
14/19
Doc ID 022179 Rev 1
AN3978
Demonstration board photo
Appendix A
Demonstration board photo
Figure 8.
Demonstration board - top view
Figure 9.
Demonstration board - bottom view
Doc ID 022179 Rev 1
15/19
Bill of material
AN3978
Appendix B
Bill of material
Application components are listed in Table 5.
Table 5.
Bill of material
Desig- Quannator
tity
Comment
Description
Footprint
Manufacturer / ordering code
C1
1
100 μF / 50 V
Electrolitic
capacitor
CAP D8x11.5
Rubycon
C2, C8,
C9
3
100 nF
Capacitor
1608[0603]
Any
C3, C4
2
4.7 nF /3 kV
Capacitor
Cap_HV_RM7.5
Any
C5
1
10 nF / 50 V
Capacitor
1608[0603]
Any
C6
1
180 pF / 50 V
Capacitor
1608[0603]
Any
C7
1
680 pF / 50 V
Capacitor
1608[0603]
Any
CN1
1
MLW14G
Header, 14-pin,
dual row, with MLW14G
key
Any
CN2
1
MLW34G
Header, 34-pin,
dual row, with MLW34G
key
Any
CN3,
CN4
2
ARK128V-A-2P
Terminal block
2-pin
MKDS1.5_2pin
Any
CN5,
CN6
2
Header 1 x 1
Header, 1-pin
HDR1X1
Any
D1
1
SM15T36A
Transil
DIODE SMC
STMicroelectronics SM15T36A
LED1
1
Green
LED 0805
green
2012[0805]_
Any
TO_DIODE_reflow
OPT1,
OPT2,
OPT3
3
TLP281
Optocoupler
HPMF4
Any
R1, R4
2
18 KΩ
Resistor
1608[0603]
Any
R2, R3,
R5, R6
4
470 Ω
Resistor
1608[0603]
Any
R7,
R10
2
10 KΩ
Resistor
1608[0603]
Any
R8, R9,
R11,
R12
4
3.3 KΩ
Resistor
1608[0603]
Any
16/19
Doc ID 022179 Rev 1
50ZL100MEFC8X11.5
AN3978
References
Table 5.
Bill of material (continued)
Desig- Quannator
tity
TP1,
TP2,
TP3,
TP4,
TP5,
TP6
6
U1
1
W1
W2
Comment
Description
Footprint
Manufacturer / ordering code
Test point
Test_Point_Small
Any
L6370Q
Intelligent
power switch
VFQFPN48_PADS STMicroelectronics L6370QTR
1
5.08 mm
Shorting link
Shorting link
5.08 mm 10 A
Any
1
2.54 mm
Jumper
Jumper 2P
2.54 mm
Any
References
1.
L6370Q device datasheet
2.
IEC61131-2: Programmable Controllers - Equipment Requirements and Tests
3.
IEC61000-4-4: Electrical fast transient/burst immunity test
4.
IEC61000-4-5: Surge immunity test.
Doc ID 022179 Rev 1
17/19
Revision history
AN3978
Revision history
Table 6.
18/19
Document revision history
Date
Revision
05-Dec-2011
1
Changes
Initial release.
Doc ID 022179 Rev 1
AN3978
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2011 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 022179 Rev 1
19/19