UG175: TS331x EVB User's Guide The TS331x is a low power boost converter with an industry leading low quiescent current of 150 nA, enabling ultra long battery life in systems running from a variety of battery sources. The TS331x steps up input voltages from 0.9 V to 5.0 V to eight selectable output voltages ranging from 1.8 V to 5.0 V. The TS331x includes two output options, one being an always-on storage output while the additional output is an output load switch that is designed to burst-on loads in a low duty cycle manner. The TS331x output voltage can be set via jumpers S0, S1, and S2. Both the STORE and OUT output can be monitored along with the power good output VGOOD. Jumper OUT_ON is available to disable or enable the OUT output. KEY FEATURES • Input Voltage Range: 0.9 V–5.0 V • Jumper selectable VOUT: • 1.8 V, 2.1 V, 2.5 V, 2.85 V, 3 V, 3.3 V, 4.1 V, 5 V (TS3310/12) • 4 V, 4.2 V, 4.35 V, 4.5 V, 4.6 V, 4.7 V, 4.8 V, 4.9 V (TS3314) • OUT Enable/Disable Jumper • 10 μH Inductor, 900 mA ISAT • Taiyo Yuden: CBC3225T100KR ORDERING INFORMATION • TS3310DB • TS3312DB (1.9 V UVLO) • TS3314DB (4.xV outputs) silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 UG175: TS331x EVB User's Guide Description 1. Description The maximum available output current for the TS331x is a function of the inductor value and the average input current. The average input current will vary according to the load. When the output current is at its maximum, the averaged input current is also at a maximum. The maximum averaged input current is defined by the following equation. I IN (AVG,MAX ) = I pk 2 = 1µs × V IN L Equation 1. Maximum Average Input Current Calculation The expected maximum STORE output current is defined by the following equation. I STORE (MAX ) = V IN V OUT × I IN (AVG,MAX ) × Efficiency Equation 2. Expected Maximum STORE Output Current Calculation The table below lists some example inductor values and the corresponding expected maximum output load current available for the TS331x, assuming an 85% efficiency, an input voltage of 2 V, and an output voltage of 3 V (4.35 V for TS3314). Table 1.1. Expected Maximum Output Current L TS3310 and TS3312 TS3314 ISTORE(MAX) ISTORE(MAX) 10 µH 56.67 mA 38.63 mA 22 µH 25.75 mA 17.56 mA 33 µH 17.17 mA 11.71 mA 100 µH 5.67 mA 3.86 mA The TS3310 and TS3312 demo board is configured for 3 V output by default. The TS3314 demo board is configured for a 4.35 V output by default. The TS331x demo board provides test points to monitor the output voltage STORE and OUT. The power good pin, VGOOD, is pulled to the STORE output by a 3.3 MΩ pull-up resistor R1 and can be monitored via test point PG. To enable or disable the OUT output voltage, a jumper for the OUT_ON pin is available. The STORE and OUT output voltage can be set via jumpers S2, S1, and S0. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 1 UG175: TS331x EVB User's Guide Quick Start Procedure 2. Quick Start Procedure Table 2.1. STORE Output Voltage Options S2 S2 S0 TS3310 TS3312 TS3314 STORE STORE STORE 0 0 0 1.8 V — 4V 0 0 1 2.5 V 2.5 V 4.2 V 0 1 0 3.3 V 3.3 V 4.35 V 0 1 1 5V 5V 4.5 V 1 0 0 2.1 V 2.1 V 4.6 V 1 0 1 2.85 V 2.85 V 4.7 V 1 1 0 3V 3V 4.8 V 1 1 1 4.1 V 4.1 V 4.9 V To evaluate the TS331x, perform the following steps: 1. Connect the battery or power supply’s positive terminal to the test point labeled IN. Connect the negative terminal of the battery or power supply to the test point labeled GND. 2. To monitor the STORE output voltage, connect the positive terminal of the voltmeter to the test point labeled STORE. Connect the negative terminal of the voltmeter to the test point labeled GND. The output voltage should be approximately 3 V (TS3314: 4.35 V). 3. To monitor the STORE output voltage ripple, connect an Oscilloscope probe to the test point labeled STORE. 4. To monitor the OUT output voltage, connect the positive terminal of the second voltmeter to the test point labeled OUT. Connect the negative terminal of the voltmeter to the test point labeled GND. The output voltage should be approximately 3 V (TS3314: 4.35 V). To disable the OUT output voltage, set jumper OUT_ON to LOW. 5. To monitor the open-drain VGOOD output, connect an Oscilloscope Probe to the test point labeled PG. The VGOOD output signal assumes a high impedance once the STORE output voltage is greater than 90% of the target output voltage, which is 2.7 V for the 3 V default configuration for the TS3310 and TS3312. 90% of the target output voltage for the TS3314 is 3.915 V for the default 4.35 V configuration. To evaluate the TS331x with a different output voltage setting, reconfigure the provided jumpers S0–S2. Please refer to the above table for the available output voltages and their corresponding S0–S2 jumper configuration. Figure 2.1. TS331x-EVB Schematic silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 2 UG175: TS331x EVB User's Guide Quick Start Procedure Table 2.2. TS331x-EVB Component List Quantity Reference Value Type Footprint OPN 2 C1, C2 22 µF 6.3 V ±20% X5R C0805 C0805X5R6R3-226M 3 C3, C4, C5 0.1 µF 16 V ±10% X7R C0402 C0402X7R160-104K 1 J1 Header HDR1X1 TSW-101-07-L-S 4 JP1, JP2, JP3, JP4 Header CONN-1X3 TSW-103-07-L-S 4 JP5, JP6, JP7, JP8 Header CONN1X2 TSW-102-07-L-S 4 JS1, JS2, JS3, JS4 Shunt N/A SNT-100-BK-T 1 L1 UnShielded IND-CB3225 CBC3225T100KR 1 PCB BARE PCB N/A TS3310_12_14DB Rev 1.0 1 R1 3 MΩ Thickfilm R0603 CR0603-16W-305J 1 U1 TS3310 Power DFN10N2.0P0.4E0.9X1.4 TS3310ITD1022 10 µH Rating Voltage Tolerance 900 mA ±10% 1/16 W ±5% 5V TS3312 TS3312ITD1022 TS3314 TS3314ITD1022 silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 3 Smart. Connected. Energy-Friendly. Products Quality Support and Community www.silabs.com/products www.silabs.com/quality community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are not designed or authorized for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®, ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com