PRODUCT BULLETIN 2008-01 PRODUCT: DATE: .039/(1.00mm) Pitch SMT Sockets, Adapters, Headers January 29, 2008 PART NUMBER SERIES: TYPE: MHS, FHA, DHS, DHAM Contact System Test Results Test Set Up The following tests were performed on a 5989G contact and .011 diameter mating male pin. The connector format was a 388 position BGA 1.00mm pitch molded socket and FR-4 adapter. The components were mounted to test PC boards. The parts were not shrouded and there were no locking features on the connector assemblies. Mechanical Shock: (Test Standard BS EN 68-2-27 peak value 50G duration six milliseconds, wave form half sine. Velocity 11.3 feet per second, three shocks, three axes, eighteen shocks total.) LLCR max. change +1.9 no opens. Acceptable for GR-1217 R9-21 less than 10mil ohm change. Advanced exceeds peak value for 9.1.2.2 (15g). Low Level Contact Resistance: (Test Standards EIA 364 TP 23) Initial results 18.1 mil ohm max. Meets GR-1217 R5-76 (20 mil ohm max resistance for noble contact metallization) Mixed Flowing Gas Testing: Passed GR-1217 SQ Level II (see section 5.2.5 R5-61) Controlled environment. Advanced testing exceeded time requirements by 10 days. Results upon request. High Temperature: (Test Standard, BN EN 60068-2-2. Temperature 125ºC for 48 hours mated and mounted.) No physical damage was found. LLCR maximum changes 4.9 mil ohms max. Test results meet GR-1217 R5-76 (20 mil ohm max change) GR-1217 requires EIA-364-TP17 method A 85ºC (185ºF) for 500 hrs. Advanced tested to 125ºC (275ºF) for 48 hrs. 130ºC is the materials RTI (relative temp. index). Thermal Cycle: (Test Standard BN EN 60068-2-14 Max temperature –40ºC to 125ºC. Time at temperature 10 minutes. Ramp time hot to cold 20 minutes. Ramp cold to hot 15 minutes. Number of cycles 100.) LLCR +2.4 max change. Test results meet GR-1217 R5-76 (20 mil ohm max change) GR-1217 requires EIA-TP32 condition I. Temperature range –55ºC to 85ºC five cycles. Advanced testing exceeds the maximum temperature and number of cycles required. See requirements 6.3.3 R6-57. Vibration with Thermal Cycle: (Test standard BS EN 600-264 5Hz to 2000Hz sweep time 20 minutes. Duration 16 hours per axis. Number of cycles 48 maximum temperature 125ºC to –40ºC Time at temperature 10 minutes. Ramp hot to cold 20 minutes Ramp cold to hot 15 minutes.) LLCR 1.8 max change. Acceptable for GR-1217 R9-21 less than 10 mil ohm change. Advanced vibration testing incorporates thermal cycling. Advanced test exceeds requirements for GR-1217 9.1.2.2. Porosity: (EIA 364 TP60 Nitric Vapor Test) Results: Passed. Plating Thickness: (Measured prior to MFG testing) Gold 32.5 min. micro inches acceptable for GR1217 5.2 Nickel 90.6 min. micro inches acceptable for GR1217 5.2 Durability: (Test Standards EIA 364 TP 9) Acceptable for GR-1217 R5-61 Number of cycles 25. Results: No damage. LLCR 2.1 mil ohms max. change. Acceptable for GR-1217 R5-76 (20 mil ohm max change) Insertion Withdrawal Force: Meets GR-1217 section 5.1.5 Insertion force: 14 pin average 1.9 lbs. Withdrawal force: 14 pin average 1.5 lbs. Contact to Shell Retention: GR-1217, 5.1.6-R5-37 requirement 3 lbs. retention Advanced meets contact to shell retention, 4 lbs. min. This information was taken from test report #205484 Rev1.1 January 3, 2006 and test report #206327 MFG testing August 22, 2006. Testing was performed by an independent test lab. .................................................................................................................... Advanced Interconnections Corp. ■ 5 Energy Way ■ West Warwick, Rhode Island U.S.A. Tel: (800) 424-9850 ■ (401) 823-5200 ■ FAX: (401) 823-8723 E-mail: [email protected] ■ Web Site: http://www.advanced.com