End of Life - August 2013 FP..P www.vishay.com Vishay Dale Metal Film Resistors, Pulse Withstanding Protective FEATURES • Special Vishay Dale design provides lightning withstand characteristics along with resistor functionality • A thicker tin oxide power film system provides lightning surge absorption capabilities • Higher turns ratio and glass substrate provide sharper fusing characteristic than the standard flameproof product line • Protect against a variety of electrical hazards which can change or destroy sensitive electronic equipment including high energy voltage surges caused by power line anomalies (direct power crosses or inductively coupled effects) and other momentary overvoltages • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 Note * Lead (Pb)-containing terminations are not RoHS-compliant. Exemptions may apply. STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL HISTORICAL MODEL POWER RATING P70 °C W RESISTANCE RANGE (2) TOLERANCE ±% CUTOFF VALUE (1) FP1/2P FP001P FP002P FP003P FP069P FP1/2P FP1P FP2P FP3P FP69P 0.5 1 2 3 2 10 to 1M 10 to 1M 355 to 125K 46.4 to 125K 25 to 126K 1, 2, 5 1, 2, 5 1, 2, 5 1, 2, 5 1, 2, 5 2K00 1K00 355R 250R 400R Notes Pulse withstanding capabilities are value dependent. Values above the cutoff value will meet all of the surge test requirements shown on the following pages. (2) Contact factory for values outside these published ranges. (1) MARKING - DALE - Value - Tolerance - Style and case size - Date code (year/week) GLOBAL PART NUMBER INFORMATION New Global Part Numbering: FP002P1K00F9256B8 (preferred part numbering format) F P 0 0 2 P 1 K 0 0 F 9 2 5 6 B 8 GLOBAL MODEL RESISTANCE VALUE TOLERANCE CODE SPEC CODES PACKAGING (3) (See Standard Electrical Specifications table) R= K = k M = M 10R0 = 10 1K30 = 1.3 k 1M00 = 1.0 M F=±1% G=±2% J=±5% 5555 = FP1/2P 6206 = FP001P 9256 = FP002P 9303 = FP003P 7532 = FP069P EK = Lead (Pb)-free, strip EA = Lead (Pb)-free, T/R B8 = Tin/lead, strip CH = Tin/lead, T/R (750 pieces) CJ = Tin/lead, T/R (1000 pieces) Historical Part Number: FP2P 1K00 1 % B8 (will continue to be accepted) FP2P 1K00 1% B8 HISTORICAL MODEL RESISTANCE VALUE TOLERANCE CODE PACKAGING Notes (3) Some packaging codes are model specific. (4) For additional information on packaging, refer to the Through Hole Resistor Packaging document (www.vishay.com/doc?31544). Revision: 05-Feb-13 Document Number: 31030 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 End of Life - August 2013 FP..P www.vishay.com Vishay Dale DIMENSIONS in inches (millimeters) B 1.500 ± 0.125 (1) (38.10 ± 3.18) A D GLOBAL MODEL A B D FP1/2P 0.360 ± 0.020 (9.14 ± 0.51) 0.138 + 0.012 - 0.023 (3.51 + 0.31 - 0.58) 0.032 ± 0.002 (0.81 ± 0.05) FP001P 0.560 ± 0.031 (14.22 ± 0.79) 0.190 + 0.005 - 0.030 (4.83 + 0.13 - 0.76) 0.032 ± 0.002 (0.81 ± 0.05) FP002P 0.687 ± 0.031 (17.45 ± 0.79) 0.300 ± 0.020 (7.62 ± 0.51) 0.032 ± 0.002 (0.81 ± 0.05) FP003P 0.900 ± 0.055 (22.86 ± 1.40) 0.300 ± 0.020 (7.62 ± 0.51) 0.032 ± 0.002 (0.81 ± 0.05) FP069P 0.516 ± 0.021 (13.11 ± 0.53) 0.225 ± 0.012 (5.72 ± 0.31) 0.032 ± 0.002 (0.81 ± 0.05) % OF RATED POWER Note (1) Lead length for product in strip pack. For product supplied in Tape and Reel, the actual lead length would be based on the body size, tape spacing and lead trim. 120 + 70 °C 100 80 60 FP001P, FP002P, FP003P 40 20 FP1/2P 0 0 50 100 150 200 250 300 AMBIENT TEMPERATURE °C % OF RATED POWER DERATING 120 + 25 °C 100 3W 80 2W 60 40 20 0.6 W FP069P 0 0 50 100 150 200 250 300 AMBIENT TEMPERATURE °C DERATING Revision: 05-Feb-13 Document Number: 31030 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 End of Life - August 2013 FP..P www.vishay.com Vishay Dale LIGHTNING PULSE WAVE FORMS Lightning pulse wave forms are defined by three numbers: • Maximum time to reach peak voltage level (typically 10 μs) • Minimum time for voltage to decrease to half value • The peak voltage level VOLTS Three examples are shown below. 1600 1200 800 400 0 200 VOLTS 10 by 160 µs up to 1500 V 600 1000 µs FCC - Longitudinal Surge 1600 1200 800 400 0 200 600 VOLTS 10 by 560 µs up to 800 V 1000 µs FCC - Metallic Surge 1600 1200 800 400 0 200 10 by 1000 µs up to 1000 V Revision: 05-Feb-13 600 1000 µs REA - Current Surge Document Number: 31030 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 End of Life - August 2013 FP..P www.vishay.com Vishay Dale 1750 VOLTS VOLTS These graphs show the relationship value and pulse withstanding voltage for FP1/2P thru FP003P using a 1.0 % resistance shift after 10 pulses as the figure of merit. The stable operating region of each package is on the right side of the appropriate line. FP003P FP002P FP069P FP001P 1500 1750 FP003P FP002P FP069P FP001P 1500 1250 1250 1000 1000 750 750 500 500 FP1/2P 250 0 250 FP1/2P (1500 µ at 2 kΩ) 100 300 500 700 0 900 RESISTANCE (Ω) VOLTS 10 x 160 µs 100 300 500 700 900 RESISTANCE (Ω) 10 x 560 µs 1750 FP002P 1500 FP003P FP069P 1250 FP001P FP1/2P 1000 750 500 250 0 100 10 x 1000 µs 300 500 700 900 RESISTANCE (Ω) PACKAGING GLOBAL MODEL FP1/2P, FP001P, FP069P FP002P, FP003P Revision: 05-Feb-13 PACKAGING TYPE Strip PACKAGING CODE LEAD (Pb)-BEARING LEAD (Pb)-FREE B8 EK Tape/reel CJ EA Strip B8 EK Tape/reel CH EA Document Number: 31030 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000