VJ....W1BC MLCC Chip Array www.vishay.com Vishay Surface Mount Multilayer Ceramic Chip Capacitors Array for Commodity Applications FEATURES • High density mounting due to mounting space saving • Mounting cost saving • Increased throughput • Dry sheet manufacturing technology • Base Metal Electrode system (BME) • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS • For use as a bypass for digital and analog signal line noise • Computer motherboards and peripherals • The common electronic circuits ELECTRICAL SPECIFICATION Size Dielectric Capacitance (1) Capacitance Tolerance (2) Rated Voltage (VDC) tan /Q (1) Insulation Resistance at UR 4 x 0603 C0G (NP0) X7R Y5V 10 pF to 470 pF 180 pF to 100 nF 10 nF to 100 nF J (± 5 %), K (± 10 %) K (± 10 %), M (± 20 %) M (± 20 %) Z (-20 %/+80 %) 50 V 16 V, 50 V 50 V Cap. < 30 pF: Q 400 + 20 C Cap. 30 pF: Q 1000 UR = 50 V: 2.5 % UR = 16 V: 3.5 % 5% 10 G Operating Temperature Capacitance Change Termination 10 G or R x C 500 x F, whichever is less -55 °C to +125 °C ± 30 ppm -25 °C to +85 °C ± 15 % +30 %/-80 % Ni/Sn lead (Pb)-free termination Notes (1) (2) Measured at 30 % ~ 70 % related humidity NP0: apply 1.0 VRMS ± 0.2 VRMS, 1.0 MHz ± 10 % at the conditions of 25 °C ambient temperature X7R: apply 1.0 VRMS ± 0.2 VRMS, 1.0 kHz ± 10 % at the conditions of 25 °C ambient temperature Y5V: apply 1.0 VRMS ± 0.2 VRMS, 1.0 kHz ± 10 % at the conditions of 20 °C ambient temperature Preconditioning for X7R, Y5V MLCC: Perform a heat treatment at 150 °C ± 10 °C for 1 h, then leave in ambient condition for 24 h ± 2 h before measurement. Revision: 07-Nov-13 Document Number: 28539 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VJ....W1BC MLCC Chip Array www.vishay.com Vishay QUICK REFERENCE DATA DIELECTRIC CASE CAPACITANCE MAXIMUM VOLTAGE (V) MINIMUM MAXIMUM C0G (NP0) 0612 50 10 pF 470 pF X7R 0612 50 180 pF 100 nF Y5V 0612 50 10 nF 100 nF Note • Detail ratings see “Selection Chart” ORDERING INFORMATION VJ06C4 A 100 J X A C W1BC SIZE CODE DIELECTRIC CAPACITANCE TOLERANCE TERMINATION RATED VOLTAGE PACKAGING PROCESS CODE FOR BASIC COMMODITY 06C4 A = C0G (NP0) Y = X7R V = Y5V Two significant digits followed by the number of zeros. R is in place of decimal point: 100 = 10 pF 101 = 100 pF J=±5% K = ± 10 % M = ± 20 % Z = -20 %/ +80 % X = Ni Barrier J = 16 V A = 50 V C = 7" reel/ paper tape DIMENSIONS in inches (millimeters) L S W T BW P SIZE CODE L W T MAX. S BW P 0612 (1632) 0.125 0.006 (3.20 ± 0.15) 0.063 0.006 (1.60 ± 0.15) 0.036 (0.90) 0.012 ± 0.008 (0.30 ± 0.20) 0.016 ± 0.006 (0.40 ± 0.15) 0.031 ± 0.006 (0.80 ± 0.15) Revision: 07-Nov-13 Document Number: 28539 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VJ....W1BC MLCC Chip Array www.vishay.com Vishay SELECTION CHART DIELECTRIC C0G (NP0) X7R STYLE Y5V VJ06C4 SIZE CODE 0612 (4 x 0603) VOLTAGE VDC VOLTAGE CODE 50 V 16 V 50 V 50 V A J A A CAP. CODE CAP. 100 10 pF B 150 15 pF B 220 22 pF B 330 33 pF B 470 47 pF B 680 68 pF B 101 100 pF B 151 150 pF B 181 180 pF B B 221 220 pF B B 271 270 pF B B 331 330 pF B B 391 390 pF B 471 470 pF B 102 1.0 nF B 152 1.5 nF B 222 2.2 nF B 332 3.3 nF B 472 4.7 nF B 682 6.8 nF B 103 10 nF B B 153 15 nF B B B 223 22 nF B B B 333 33 nF B B 473 47 nF B B 683 68 nF B 104 100 nF B B B Note • Letters indicate product thickness, see “Packaging Quantities” Revision: 07-Nov-13 Document Number: 28539 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VJ....W1BC MLCC Chip Array www.vishay.com Vishay PACKAGING QUANTITIES SIZE CODE 06C4 (4 x 0603) 7" REEL (C) 13" REEL (P) 0.80 ± 0.10 4K - PAPER TAPE SPECIFICATIONS DIMENSIONS OF PAPER TAPE in millimeters P0 SYMBOL P2 D0 PAPER TAPE THICKNESS (mm) E F W B0 A0 P1 REEL SPECIFICATION PRODUCT SIZE CODE 06C4 (4 x 0603) A0 2.00 ± 0.10 B0 3.50 ± 0.10 W 8.00 ± 0.10 E 1.75 ± 0.05 F 3.50 ± 0.05 D0 1.50 ± 0.05 P0 4.00 ± 0.10 P1 4.00 ± 0.10 P2 2.00 ± 0.05 REEL DIMENSIONS AND TAPE WIDTH in millimeters D C A SYMBOL Ø 180 mm; 7" Ø 330 mm; 13" A 13.0 ± 0.5 13.0 ± 0.5 B 9.0 ± 1.0 9.0 ± 1.0 C 178.0 ± 1.0 330.0 ± 1.0 D 60.0 ± 1.0 100.0 ± 1.0 B Revision: 07-Nov-13 Document Number: 28539 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VJ....W1BC MLCC Chip Array www.vishay.com Vishay CONSTRUCTION NO. NAME C0G (NP0), X7R, Y5V 1 Ceramic material BaTiO3 based 2 Inner electrode 3 4 5 Termination Ni Inner layer Cu Middle layer Ni Outer layer Sn (matt) 3 4 5 1 2 STORAGE AND HANDLING CONDITIONS (1) To store products at 5 °C to 40 °C ambient temperature and 20 % to 70 % relative humidity conditions. (2) The product is recommended to be used within one year after shipment. Check solderability in case of shelf life extension is needed. Cautions: a. Do not store products in a corrosive environment such as sulfide, chloride gas, or acid. It may cause oxidization of electrode, which easily be resulted in poor soldering. b. To store products on the shelf and avoid exposure to moisture. c. Do not expose products to excessive shock, vibration, direct sunlight and so on. Revision: 07-Nov-13 Document Number: 28539 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000