End of Life - August 2013 FP www.vishay.com Vishay Dale Metal Film Resistors, Industrial, Flameproof FEATURES • Small physical size • Low cost • FP resistors have the ability to withstand overloads up to 100 times rated power without any trace of flame • Exceptional frequency characteristics • Especially suited for circuitry where functions, environments and duty cycles demand power resistors • Electroplated tin-lead or lead (Pb)-free solder finish leads • Tighter tolerances available on request • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 Note * Lead (Pb)-containing terminations are not RoHS-compliant. Exemptions may apply. STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL HISTORICAL MODEL POWER RATING P40 °C W 3 4 5 6 10 - POWER RATING P25 °C W 3.5 4 5.5 6.5 7.5 5 3 POWER RATING P70 °C W 0.5 1 1 2 2 3 4 5 7 2 MAXIMUM WORKING VOLTAGE (1) V 350 500 500 500 500 500 500 600 700 700 500 500 RESISTANCE RANGE (2) FP01/2 FP1/2 10 to 1M FP0001 FP1 10 to 1M FP0032 FP32 10 to 1M FP0002 FP2 25 to 125K FP0042 FP42 25 to 125K FP0003 FP3 22 to 125K FP0004 FP4 70 to 125K FP0005 FP5 70 to 125K FP0007 FP7 25 to 125K FP0010 FP10 25 to 125K FP0067 FP67 35 to 19K FP0069 FP69 25 to 126K Notes (1) Continuous working voltage shall be P x R or maximum working voltage, whichever is less. (2) Contact factory for values outside these published range. TOLERANCE ±% TEMPERATURE COEFFICIENT ± ppm/°C 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 150 150 150 150 150 150 150 150 150 150 150 150 GLOBAL PART NUMBER INFORMATION New Global Part Numbering: FP000251K1F9251B8 (preferred part numbering format) F P 0 0 0 2 5 1 K 1 F 9 2 5 1 B 8 GLOBAL MODEL RESISTANCE VALUE TOLERANCE CODE SPEC CODES PACKAGING (3) (See Standard Electrical Specifications table) R= K = k M = M 10R0 = 10 1K30 = 1.3 k 1M00 = 1.0 M F=±1% G=±2% J=±5% K = ± 10 % (See Spec Codes table) EK = Lead (Pb)-free, strip EL = Lead (Pb)-free, lacer EA = Lead (Pb)-free, T/R B8 = Tin/lead, strip LB = Tin/lead, lacer CH = Tin/lead, T/R (750 pieces) CJ = Tin/lead, T/R (1000 pieces) G1 = Tin/lead, T/R (600 pieces) Historical Part Number: FP2 5112 F B8 (will continue to be accepted) FP2 5112 F B8 HISTORICAL MODEL RESISTANCE VALUE TOLERANCE CODE PACKAGING Notes (3) Some packaging codes are model specific. (4) For additional information on packaging, refer to the Through Hole Resistor Packaging document (www.vishay.com/doc?31544). Revision: 01-Feb-13 Document Number: 31020 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 End of Life - August 2013 FP www.vishay.com Vishay Dale DIMENSIONS in inches (millimeters) 1.500 ± 0.125 (1) (38.10 ± 3.18) B A D GLOBAL MODEL A B D FP01/2 0.360 ± 0.020 (9.14 ± 0.51) (2) 0.138 + 0.012 - 0.023 (3.51 + 0.31 - 0.58) 0.032 ± 0.002 (0.81 ± 0.05) FP0001 0.560 ± 0.031 (14.22 ± 0.79) 0.190 + 0.005 - 0.030 (4.83 + 0.13 - 0.76) 0.032 ± 0.002 (0.81 ± 0.05) FP0032 0.560 ± 0.031 (14.22 ± 0.79) 0.190 + 0.005 - 0.030 (4.83 + 0.13 - 0.76) 0.040 ± 0.002 (1.02 ± 0.05) FP0002 0.687 ± 0.031 (17.45 ± 0.79) 0.300 ± 0.020 (7.62 ± 0.51) 0.032 ± 0.002 (0.81 ± 0.05) FP0042 0.687 ± 0.031 (17.45 ± 0.79) 0.300 ± 0.020 (7.62 ± 0.51) 0.045 ± 0.002 (1.14 ± 0.05) FP0003 0.900 ± 0.031 (22.86 ± 0.79) 0.300 ± 0.020 (7.62 ± 0.51) 0.032 ± 0.002 (0.81 ± 0.05) FP0004 1.530 ± 0.035 (38.86 ± 0.89) 0.300 ± 0.020 (7.62 ± 0.51) 0.032 ± 0.002 (0.81 ± 0.05) FP0005 1.710 ± 0.035 (43.43 ± 0.89) 0.300 ± 0.020 (7.62 ± 0.51) 0.032 ± 0.002 (0.81 ± 0.05) FP0007 2.040 ± 0.035 (51.82 ± 0.89) 0.300 ± 0.020 (7.62 ± 0.51) 0.032 ± 0.002 (0.81 ± 0.05) FP0010 2.040 ± 0.035 (51.82 ± 0.89) 0.300 ± 0.020 (7.62 ± 0.51) 0.032 ± 0.002 (0.81 ± 0.05) FP0067 0.900 ± 0.031 (22.86 ± 0.79) 0.300 ± 0.020 (7.62 ± 0.51) 0.032 ± 0.002 (0.81 ± 0.05) FP0069 0.516 ± 0.021 (13.11 ± 0.53) 0.225 ± 0.012 (5.72 ± 0.31) 0.032 ± 0.002 (0.81 ± 0.05) Notes (1) Lead length for product in strip pack. For product supplied in Tape and Reel, the actual lead length would be based on body size, tape spacing and lead trim. (2) Clean lead to clean lead dimensions on FP1/2 are 0.347" (11.10 mm) maximum. 100 FP0001, FP0002, FP0003, FP0004, FP0005, FP0007 80 60 FP01/2 FP0032 FP0042 40 20 0 50 100 150 3W 80 2W 60 FP0069 40 0.6 W 20 0 250 50 80 60 40 FP0010 100 150 200 250 AMBIENT TEMPERATURE ° C 70 % OF RATED POWER 100 20 100 AMBIENT TEMPERATURE ° C 70 % OF RATED POWER 200 % OF RATED POWER % OF RATED POWER DERATING 100 5W 80 4W 60 3W 40 FP0067 20 0 50 40 Revision: 01-Feb-13 100 150 200 250 AMBIENT TEMPERATURE ° C 0 50 100 150 200 250 AMBIENT TEMPERATURE ° C Document Number: 31020 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 End of Life - August 2013 FP www.vishay.com Vishay Dale SPEC CODES GLOBAL MODEL FP01/2 FP0001 FP0032 FP0002 SPEC RESISTOR TOLERANCE DESCRIPTION 5605 1, 2, 5, 10 Color banded, 4 or 5 bands depending on tolerance 5610 1, 2, 5, 10 Alphanumeric marking 6200 2, 5, 10 Color banded, 4 bands 6201 1 Color banded, 5 bands 6601 1 Color banded, 5 bands 6602 2, 5, 10 Color banded, 4 bands 9251 1, 2, 5, 10 Alphanumeric marking 9201 1 Color banded, 5 bands 9202 2, 5, 10 Color banded, 4 bands 9300 1, 2, 5, 10 Alphanumeric marking 9320 2, 5, 10 Color banded, 4 bands 9330 1 Color banded, 5 bands FP0004 9400 1, 2, 5, 10 Alphanumeric marking FP0005 9500 1, 2, 5, 10 Alphanumeric marking FP0007 9700 1, 2, 5, 10 Alphanumeric marking FP0010 9800 1, 2, 5, 10 Alphanumeric marking FP0067 9550 1, 2, 5, 10 Alphanumeric marking 7500 1, 2, 5, 10 Alphanumeric marking 7536 2, 5, 10 Color banded, 4 bands 7538 1 Color banded, 5 bands FP0042 FP0003 FP0069 MARKING - DALE - Value - Tolerance ± 1 % tolerance parts are marked with 5 color bands. 5 bands, EIA Standard RS196. First significant figure Third significant figure Revision: 01-Feb-13 Second significant figure Multiplier Tolerance, 1-1/2 times size - Model and case size (Date and source code included on some styles) ± 2 %, ± 5 % and ± 10 % tolerance parts are marked with 4 color bands. 4 band commercial, EIA Standard. First significant figure Multiplier Second significant figure Tolerance Document Number: 31020 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 End of Life - August 2013 FP www.vishay.com Vishay Dale PERFORMANCE TEST MAXIMUM R (TYPICAL TEST LOTS) ± % FP01/2 FP0001 FP0032 FP0002 FP0042 FP0003 FP0004 FP0005 FP0007 FP0010 FP0067 FP0069 Short Time Overload 0.5 1.0 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 Low Temperature Operation 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.25 0.25 Moisture Resistance 1.0 1.5 1.5 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 Shock 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 Vibration 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 Temperature Cycle 1.0 1.0 1.0 0.5 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.5 Load Life (1000 h Rated Conditions) 1.0 2.0 2.0 5.0 2.0 5.0 5.0 5.0 5.0 5.0 5.0 3.0 Terminal Strength 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 Dielectric Withstanding Voltage 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.25 0.25 Effect Solder Heat 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.25 0.25 PACKAGING GLOBAL MODEL FP01/2, FP0001, FP0032, FP0069 FP0002, FP0003, FP0042, FP0067 FP0004 FP0005, FP0007, FP0010 Revision: 01-Feb-13 PACKAGING TYPE PACKAGING CODE LEAD (Pb)-BEARING LEAD (Pb)-FREE Strip B8 EK Tape/reel CJ EA Strip B8 EK Tape/reel CH EA Lacer LB EL Tape/reel G1 EA Lacer LB EL Document Number: 31020 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000