MCP14628 Data Sheet-DS22083

MCP14628
2A Synchronous Buck Power MOSFET Driver
Features
General Description
• Dual Output MOSFET Driver for Synchronous
Applications
• High Peak Output Current: 2A (typical)
• Adaptive Cross Conduction Protection
• Internal Bootstrap Blocking Device
• +36V BOOT Pin Maximum Rating
• Enhanced Light Load Efficiency Mode
• Low Supply Current: 80 µA (typical)
• High Capacitive Load Drive Capability:
- 3300 pF in 10 ns (typical)
• Tri-State PWM Pin for Power Stage Shutdown
• Input Voltage Undervoltage Lockout Protection
• Space Saving Packages:
- 8-Lead SOIC
- 8-Lead 3x3 DFN
The MCP14628 is a dual MOSFET gate driver
designed to optimally drive two N-Channel MOSFETs
arranged in a non-isolated synchronous buck converter
topology. With the capability to source 2A peaks
typically from both the high-side and low-side drives,
the MCP14628 is an ideal companion to buck controllers that lack integrated gate drivers. Additionally,
greater design flexibility is offered by allowing the gate
drivers to be placed close to the power MOSFETs.
Applications
• High Efficient Synchronous DC/DC Buck
Converters
• High Current Low Output Voltage Synchronous
DC/DC Buck Converters
• High Input Voltage Synchronous DC/DC Buck
Converters
• Core Voltage Supplies for Microprocessors
The MCP14628 features the capability to sink 3.5A
peak typically for the low-side gate drive. This allows
the MCP14628 the capability of holding off the low-side
power MOSFET during the rising edge of the PHASE
node. Internal adaptive cross conduction protection
circuitry is also used to mitigate both external power
MOSFETs from simultaneously conducting.
The low resistance pull-up and pull-down drives allow
the MCP14628 to quickly transition a 3300 pF load in
typically 10 ns and with a propagation time of typically
20 ns. Bootstrapping for the high-side drive is internally
implemented which allows for a reduced system cost
and design complexity.
The PWM input to the MCP14628 can be tri-stated to
force both drive outputs low for true power stage
shutdown. Light load system efficiency is improved by
using the diode emulation feature of the MCP14628.
When the FCCM pin is grounded, diode emulation
mode is entered. In this mode, discontinuous conduction is allowed by sensing when the inductor current
reach zero and turning off the low-side power
MOSFET.
Package Types
8-Lead DFN
8-Lead SOIC
HIGHDR
1
8
PHASE
BOOT
2
7
FCCM
VCC
PWM
3
6
VCC
LOWDR
GND
4
5
LOWDR
HIGHDR
1
8
PHASE
BOOT
2
7
FCCM
PWM
3
6
GND
4
5
Note 1: Exposed pad on the DFN is electrically isolated.
© 2008 Microchip Technology Inc.
DS22083A-page 1
MCP14628
Typical Application Schematic
CBOOT
VSUPPLY = 12V
CURRENT
SENSE
BOOT
MCP14628
VCC = 5V
FCCM
CONTROL
VCC
UGATE
FCCM
PHASE
PWM
LGATE
QH
QL
GND
VEXT
MCP1630
VCC
CURRENT
SENSE
FB
CS
COMP
OSC IN
VREF
GND
REFERENCE VOLTAGE
OSCILLATOR
FROM MCU
Functional Block Diagram
VCC
BOOT
FCCM
HIGHDR
Level
Shift
R
PWM
R
PHASE
Control
Logic &
Protection
VCC
LOWDR
GND
DS22083A-page 2
© 2008 Microchip Technology Inc.
MCP14628
1.0
ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings †
VCC, Device Supply Voltage............................. -0.3V to +7.0V
VBOOT, BOOT Voltage.................................... -0.3V to +36.0V
VPHASE, Phase Voltage........... VBOOT - 7.0V to VBOOT + 0.3V
VFCCM, FCCM Voltage ........................... -0.3V to VCC + .0.3V
VPWM, PWM Voltage ............................... -0.3V to VCC + 0.3V
VUGATE, UGATE Voltage ....... VPHASE - 0.3V to VBOOT + 0.3V
VLGATE, LGATE Voltage .......................... -0.3V to VCC + 0.3V
ESD Protection on all Pins ....................................2 kV (HBM)
† Notice: Stresses above those listed under "Maximum
Ratings" may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational sections of this specification is not intended.
Exposure to maximum rating conditions for extended periods
may affect device reliability.
DC CHARACTERISTICS
Electrical Specifications: Unless otherwise noted, VCC = 5V, TJ = -40°C to +125°C
Parameters
Sym
Min
Typ
Max
Units
Recommended Operating Range
VCC
4.5
5.0
5.5
V
Bias Supply Voltage
IVCC
—
80
—
µA
Conditions
VCC Supply Requirements
PWM pin floating,
VFCCM = 5V
UVLO (Rising VCC)
—
3.40
3.90
V
UVLO (Falling VCC)
2.40
2.90
—
V
—
500
—
mV
—
250
—
µA
VPWM = 5V
VPWM = 0V
Hysteresis
PWM Input Requirements
PWM Input Current
IPWM
—
-250
—
µA
PWM Rising Threshold
0.70
1.00
1.30
V
PWM Falling Threshold
3.50
3.80
4.10
V
100
175
250
ns
FCCM Low Threshold
0.50
—
—
V
FCCM High Threshold
—
—
2.0
V
High Drive Source Resistance
—
1.0
2.5
Ω
500 mA source current,
Note 1
High Drive Sink Resistance
—
1.0
2.5
Ω
500 mA sink current,
Note 1
High Drive Source Current
—
2.0
—
A
Note 1
High Drive Sink Current
—
2.0
—
A
Note 1
Low Drive Source Resistance
—
1
2.5
Ω
500 mA source current,
Note 1
Low Drive Sink Resistance
—
0.5
1.0
Ω
500 mA sink current,
Note 1
Tri-State Shutdown Hold-off Time
tTSSHD
TA = +25°C, Note 2
FCCM input Requirements
Output Requirements
Low Drive Source Current
—
2.0
—
A
Note 1
Low Drive Sink Current
—
3.5
—
A
Note 1
Note 1:
2:
Parameter ensured by design, not production tested.
See Figure 4-1 for parameter definition.
© 2008 Microchip Technology Inc.
DS22083A-page 3
MCP14628
DC CHARACTERISTICS (CONTINUED)
Electrical Specifications: Unless otherwise noted, VCC = 5V, TJ = -40°C to +125°C
Parameters
Sym
Min
Typ
Max
Units
Conditions
HIGHDR Rise Time
tRH
—
10
—
ns
CL = 3.3nF,
Note 1, Note 2
LOWDR Rise Time
tRL
—
10
—
ns
CL = 3.3nF,
Note 1, Note 2
HIGHDR Fall Time
tFH
—
10
—
ns
CL = 3.3nF,
Note 1, Note 2
LOWDR Fall Time
tFL
—
6.0
—
ns
CL = 3.3nF,
Note 1, Note 2
HIGHDR Turn-off Propagation
Delay
tPDLH
—
15
—
ns
No Load, Note 2
LOWDR Turn-off Propagation
Delay
tPDLL
—
16
—
ns
No Load, Note 2
HIGHDR Turn-on Propagation
Delay
tPDHH
10
18
30
ns
No Load, Note 2
LOWDR Turn-on Propagation
Delay
tPDHL
10
22
30
ns
No Load, Note 2
Tri-State Propagation Delay
tPTS
—
35
—
ns
No Load, Note 2
Minimum LOWDR On Time in DCM tLGMIN
—
400
Note 1: Parameter ensured by design, not production tested.
2: See Figure 4-1 for parameter definition.
—
ns
FCCM pin low Note 1
Switching Times
TEMPERATURE CHARACTERISTICS
Electrical Specifications: Unless otherwise noted, all parameters apply with VCC = 5V.
Parameter
Sym
Min
Typ
Max
Units
TA
-40
—
+85
°C
Comments
Temperature Ranges
Specified Temperature Range
Maximum Junction Temperature
TJ
—
—
+150
°C
Storage Temperature
TA
-65
—
+150
°C
Thermal Resistance, 8L-SOIC
θJA
—
149.5
—
°C/W
Thermal Resistance, 8L-DFN (3x3)
θJA
—
60.0
—
°C/W
Package Thermal Resistances
DS22083A-page 4
Typical Four-layer board
with vias to ground plane
© 2008 Microchip Technology Inc.
MCP14628
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein are
not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Note: Unless otherwise indicated, TA = +25°C with VCC = 5.0V.
25
25
tRH
tFH
20
Fall Time (ns)
Rise Time (ns)
20
tRL
15
10
5
15
10
tFL
5
0
0
0
1500
3000
4500
6000
7500
0
1500
Capacitive Load (pF)
FIGURE 2-1:
Load.
Rise Times vs. Capacitive
FIGURE 2-4:
Load.
14
Time (ns)
11
tRH
12
11
9
CLOAD = 3,300 pF
tRL
8
7
6
7
5
6
tFL
4
-40 -25 -10
5
20 35 50 65 80 95 110 125
-40 -25 -10
5
Temperature (°C)
FIGURE 2-2:
vs. Temperature.
20 35 50 65 80 95 110 125
Temperature (°C)
HIGHDR Rise and Fall Time
FIGURE 2-5:
vs. Temperature.
LOWDR Rise and Fall Time
30
24
CLOAD = 3,300 pF
28
CLOAD = 3,300 pF
26
20
tPDLH
tPDHH
16
Time (ns)
Propagation Delay (ns)
7500
9
8
18
6000
Fall Times vs. Capacitive
10
tFH
10
22
4500
12
CLOAD = 3,300 pF
Time (ns)
13
3000
Capacitive Load (pF)
24
22
18
14
16
12
14
10
12
-40 -25 -10
5
20 35 50 65 80 95 110 125
tPDHL
20
tPDLL
-40 -25 -10
FIGURE 2-3:
vs. Temperature.
HIGHDR Propagation Delay
© 2008 Microchip Technology Inc.
5
20 35 50 65 80 95 110 125
Temperature (°C)
Temperature (°C)
FIGURE 2-6:
vs. Temperature.
LOWDR Propagation Delay
DS22083A-page 5
MCP14628
Typical Performance Curves (Continued)
Note: Unless otherwise indicated, TA = +25°C with VCC = 5.0V.
60
700
CLOAD = 3,300 pF
Duty Cycle = 30%
Supply Current (µA)
Supply Current (mA)
70
50
40
30
20
10
0
100
CLOAD = 3,300 pF
FSW = 12.5 kHz
Duty Cycle = 30%
680
660
640
620
600
580
1000
10000
-40 -25 -10
5
20
35
50
65
80
95 110 125
Temperature (°C)
Frequency (kHz)
FIGURE 2-7:
Frequency.
Supply Current vs.
FIGURE 2-10:
Temperature.
Supply Current vs.
FIGURE 2-8:
Operation.
DCM to CCM Transition
FIGURE 2-11:
Operation.
CCM to DCM Transition
FIGURE 2-9:
(0.5A - 15A).
Load Transition
FIGURE 2-12:
(15A - 0.5A).
Load Transition
DS22083A-page 6
© 2008 Microchip Technology Inc.
MCP14628
Typical Performance Curves (Continued)
Note: Unless otherwise indicated, TA = +25°C with VCC = 5.0V.
FIGURE 2-13:
Operation.
HIGHDR and LOWDR
© 2008 Microchip Technology Inc.
DS22083A-page 7
MCP14628
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
3.1
PIN FUNCTION TABLE .
SOIC
3x3 DFN
Symbol
Description
1
1
HIGHDR
2
2
BOOT
3
3
PWM
PWM Input Control Pin
4
4
GND
Ground
5
5
LOWDR
High-side Gate Driver Pin
Floating Bootstrap Supply Pin
Low-side Gate Driver Pin
6
6
VCC
7
7
FCCM
Forced Continuous Conduction Mode Pin
8
8
PHASE
Switch Node Pin
—
PAD
NC
High-side Gate Driver Pin
(HIGHDR)
Supply Input Voltage
Exposed Metal Pad
3.6
Supply Input Voltage Pin (VCC)
The HIGHDR pin provides the gate drive signal to
control the high-side power MOSFET. The gate of the
high-side power MOSFET is connected to this pin.
The VCC pin provides bias to the MCP14628. A bypass
capacitor is to be placed between this pin and the GND
pin. This capacitor should be placed as close to the
MCP14628 as possible.
3.2
3.7
Floating Bootstrap Supply Pin
(BOOT)
The BOOT pin is the floating bootstrap supply pin for
the high-side gate drive. A capacitor is connected
between this pin and the PHASE pin to provide the
necessary charge to turn on the high-side power MOSFET.
3.3
PWM Input Control Pin (PWM)
The control input signal is supplied to the PWM pin.
This tri-state pin controls the state of the HIGHDR and
LOWDR pins. Placing a voltage equal to VCC/2 on this
pin causes both the HIGHDR and LOWDR to a low
state.
The FCCM pin enables or disables the forced
continuous conduction mode. With the FCCM pin connected to ground the MCP14628 enters a diode emulation mode to improve system efficiency at light loads.
Continuous conduction is forced if the FCCM pin is
connected to VCC.
3.8
Ground Pin (GND)
The GND pin provides ground for the MCP14628 circuitry. It should have a low impedance connection to
the bias supply source return. High peak currents will
flow out the GND pin when the low-side power
MOSFET is being turned off.
3.5
Switch Node Pin (PHASE)
The PHASE pin provides the return path for the highside gate driver. The source of the high-side power
MOSFET is connected to this pin.
3.9
3.4
Forced Continuous Conduction
Mode Pin (FCCM)
DFN Exposed Pad
The exposed metal pad of the DFN package is not
internally connected to any potential. Therefore, this
pad can be connected to a ground plane or other
copper plane on a printed circuit board to aid in heat
removal from the package.
Low-side Gate Driver Pin
(LOWDR)
The LOWDR pin provides the gate drive signal to
control the low-side power MOSFET. The gate of the
low-side power MOSFET is connected to this pin.
DS22083A-page 8
© 2008 Microchip Technology Inc.
MCP14628
4.0
DETAILED DESCRIPTION
4.1
Device Overview
The MCP14628 is a dual MOSFET gate driver
designed to optimally drive both high-side and low-side
N-channel MOSFETs arranged in a non-isolated
synchronous buck converter topology.
The MCP14628 is capable of suppling 2A (typical)
peak current to the floating high-side power MOSFET
that is connected to the HIGHDR pin. With the exception of a capacitor, all of the circuitry needed to drive
this high-side N-channel MOSFET is internal to the
MCP14628. A blocking device is placed between the
VCC and BOOT pins that allows the bootstrap capacitor
to be charged to VCC when the low-side power MOSFET is conducting. Refer to Section 5.1, for information on determining the proper size of the bootstrap
capacitor. The HIGHDR is also capable of sinking 2A
(typical) peak current.
The LOWDR is capable of sourcing 2A (typical) peak
current and sinking 3.5A (typical) peak current. This
helps ensure that the low-side power MOSFET stays
turned off during the high dv/dt of the PHASE node.
4.2
4.4
Tri-State PWM
The PWM input pin of the MCP14628 controls the high
current LOWDR and HIGHDR drive signals. These
signals have three distinct operating modes depending
upon the state of the PWM input signal.
A logic low on the PWM pin cause the LOWDR drive
signal to be high and the HIGHDR drive signal to be
low. When the PWM signal transitions to a logic high,
the LOWDR signal goes low and the HIGHDR signal go
high. To ensure proper operation the PWM input signal
should be capable of a logic low of 0V and a logic high
of 5V.
The third operating mode of the drive signals occurs
when the PWM signal is set to a value equal to VCC/2
(typically). When the PWM signal dwells at this voltage
for 175 ns (typically) the MCP14628 disables both
LOWDR and HIGHDR drive signals. Both drive signals
are pulled and held low. Once the PWM signal moves
beyond VCC/2, the MCP14628 removes the shutdown
state of the drive signals.
Adaptive Cross-Conduction
Protection
The MCP14628 prevents cross-conduction power loss
by adaptively ensuring that the high-side and low-side
power MOSFETs are not conducting simultaneously.
When the PWM signal goes low, the HIGHDR is pulled
low and the LOWDR signal is held low until the
HIGHDR reach 1V (typically). At that time, the LOWDR
is allowed to turn on.
4.3
FCCM Mode
The MCP14628 features a diode emulation mode to
enhance the light load system efficiency. The FCCM
pin enables or disables the diode emulating mode. With
the FCCM pin grounded, diode emulation mode is
entered. The forced continuous conduction mode is
entered when the FCCM pin is connected to VCC.
In diode emulation mode, the MCP14628 turns off the
low-side power MOSFET when the inductor current
reaches approximately zero even if the PWM input signal is still low. The LOWDR and HIGHDR both stay low
until the next switching cycle begins. To prevent false
termination of the LOWDR signal, there is a 400 ns
minimum on time, tLGMIN, of the LOWDR. This also
ensures that the bootstrap capacitor is fully charged.
In forced continuous conduction mode, the LOWDR of
the MCP14628 does not terminate until the PWM input
signal transitions from a low to a high.
© 2008 Microchip Technology Inc.
DS22083A-page 9
MCP14628
4.5
Timing Diagram
The PWM signal applied to the MCP14628 is suppled
by a controller IC that regulates the power supply
output. The timing diagram in Figure 4-1 graphically
depicts the PWM signal and the output signals of the
MCP14628.
VCC
PWM
tPDHH
tPDLH
tFH
1V
HIGHDR
tRH
LOWDR
1V
tPDLL
tRL
tPDHL
tFL
VCC
VCC/2
PWM
tTSSHD
tRH
0V
tFH
tPTS
HIGHDR
LOWDR
1V
tTSSHD
FIGURE 4-1:
DS22083A-page 10
tFL
tPTS
MCP14628 Timing Diagram.
© 2008 Microchip Technology Inc.
MCP14628
5.0
APPLICATION INFORMATION
5.1
Bootstrap Capacitor Select
EQUATION 5-2:
P Q = I VCC × V CC
Where:
The selection of the bootstrap capacitor is based upon
the total gate charge of the high-side power MOSFET
and the allowable droop in gate drive voltage while the
high-side power MOSFET is conducting.
EQUATION 5-1:
Q GATE
C BOOT ≥ ----------------------ΔV DROOP
Where:
PQ
=
Quiescent Power Loss
IVCC
=
No Load Bias Current
VCC
=
Bias Voltage
The main power loss occurs from the gate charge
power loss. This power loss can be defined in terms of
both the high-side and low-side power MOSFETs.
EQUATION 5-3:
P GATE = P HIGHDR + P LOWDR
CBOOT
=
bootstrap capacitor value
QGATE
=
total gate charge of the highside MOSFET
P HIGHDR = V CC × Q HIGH × F SW
ΔVDROOP
=
allowable gate drive voltage
droop
P LOWDR = V CC × Q LOW × F SW
Where:
For example:
QGATE = 30 nC
PGATE
=
Total Gate Charge Power Loss
PHIGHDR
=
High-Side Gate Charge Power
Loss
PLOWDR
=
Low-Side Gate Charge Power
Loss
ΔVDROOP = 200 mV
CBOOT ≥ 0.15 uF
A low ESR ceramic capacitor is recommend with a
maximum voltage rating that exceeds the maximum
input voltage, VCC, plus the maximum supply voltage,
VSUPPLY. It is also recommended that the capacitance
of CBOOT not exceed 1.2 uF.
5.2
Decoupling Capacitor
Proper decoupling of the MCP14628 is highly recommended to help ensure reliable operation. This decoupling capacitor should be placed as close to the
MCP14628 as possible. The large currents required to
quickly charge the capacitive loads are provided by this
capacitor. A low ESR ceramic capacitor is
recommended.
5.3
Power Dissipation
The power dissipated in the MCP14628 consists of the
power loss associated with the quiescent power and
the gate charge power.
The quiescent power loss can be calculated by the
following equation and is typically negligible compared
to the gate drive power loss.
© 2008 Microchip Technology Inc.
5.4
VCC
=
Bias Supply Voltage
QHIGH
=
High-Side MOSFET Total Gate
Charge
QLOW
=
Low-Side MOSFET Total GAte
Charge
FSW
=
Switching Frequency
PCB Layout
Proper PCB layout is important in a high current, fast
switching circuit to provide proper device operation.
Improper component placement may cause errant
switching, excessive voltage ringing, or circuit latch-up.
There are two important states of the MCP14628
outputs, high and low. Figure 5-1 depicts the current
flow paths when the outputs of the MCP14628 are high
and the power MOSFETs are turned on. Charge
needed to turn on the low-side power MOSFET comes
from the decoupling capacitor CVCC. Current flows from
this capacitor through the internal LOWDR circuitry,
into the gate of the low-side power MOSFET, out the
source, into the ground plane, and back to CVCC. To
reduce any excess voltage ringing or spiking, the
inductance and area of this current loop must be
minimized.
DS22083A-page 11
MCP14628
CBOOT
The following recommendations should be followed to
allow for optimal circuit performance.
VSUPPLY
MCP14628
PWM
Control
Logic
VCC
CVCC
FIGURE 5-1:
- The components that construct the high
current paths previously mentioned should be
placed close the MCP14628. The traces
used to construct these current loops should
be wide and short to keep the inductance and
impedance low.
- A ground plane should be used to keep both
the parasitic inductance and impedance
minimized. The MCP14628 is capable of
sourcing and sinking high peaks current and
any extra parasitic inductance or impedance
will result in non-optimal performance.
Turn On Current Paths.
The charge needed for the turning on of the high-side
power MOSFET comes from the bootstrap capacitor
CBOOT. Current flows from CBOOT through the internal
HIGHDR circuitry, into the gate of the high-side power
MOSFET, out the source, and back to CBOOT. The
printed circuit board traces that construct this current
loop need to have a small area and low inductance. To
control the inductance, short and wide traces must be
used.
Figure 5-2 depicts the current flow paths when the
outputs of the MCP14628 are low and the power
MOSFETs are turned off. These current paths should
also have low inductance and a small loop area to
minimize voltage ringing and spiking.
CBOOT
VSUPPLY
MCP14628
PWM
Control
Logic
VCC
CVCC
FIGURE 5-2:
DS22083A-page 12
Turn Off Current Paths.
© 2008 Microchip Technology Inc.
MCP14628
6.0
PACKAGING INFORMATION
6.1
Package Marking Information (Not to Scale)
8-Lead DFN
Example:
XXXX
YYWW
NNN
CABA
0812
256
8-Lead SOIC (150 mil)
XXXXXXXX
XXXXYYWW
NNN
Legend: XX...X
Y
YY
WW
NNN
e3
*
Note:
Example:
14628E
SN^^812
e3
256
Customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3)
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
© 2008 Microchip Technology Inc.
DS22083A-page 13
MCP14628
/HDG3ODVWLF'XDO)ODW1R/HDG3DFNDJH0)±[[PP%RG\>')1@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
D
e
b
N
N
L
EXPOSED PAD
E2
E
K
NOTE 1
1
2
D2
2
NOTE 1
1
BOTTOM VIEW
TOP VIEW
A
NOTE 2
A3
A1
8QLWV
'LPHQVLRQ/LPLWV
1XPEHURI3LQV
0,//,0(7(56
0,1
1
120
0$;
3LWFK
H
2YHUDOO+HLJKW
$
%6&
6WDQGRII
$
&RQWDFW7KLFNQHVV
$
5()
2YHUDOO/HQJWK
'
([SRVHG3DG:LGWK
(
2YHUDOO:LGWK
(
([SRVHG3DG/HQJWK
'
±
E
&RQWDFW/HQJWK
/
&RQWDFWWR([SRVHG3DG
.
±
±
&RQWDFW:LGWK
%6&
±
%6&
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
3DFNDJHPD\KDYHRQHRUPRUHH[SRVHGWLHEDUVDWHQGV
3DFNDJHLVVDZVLQJXODWHG
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
DS22083A-page 14
© 2008 Microchip Technology Inc.
MCP14628
/HDG3ODVWLF'XDO)ODW1R/HDG3DFNDJH0)±[[PP%RG\>')1@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
© 2008 Microchip Technology Inc.
DS22083A-page 15
MCP14628
/HDG3ODVWLF6PDOO2XWOLQH61±1DUURZPP%RG\>62,&@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
D
e
N
E
E1
NOTE 1
1
2
3
α
h
b
h
A2
A
c
φ
L
A1
L1
8QLWV
'LPHQVLRQ/LPLWV
1XPEHURI3LQV
β
0,//,0(7(56
0,1
1
120
0$;
3LWFK
H
2YHUDOO+HLJKW
$
±
%6&
±
0ROGHG3DFNDJH7KLFNQHVV
$
±
±
6WDQGRII†
$
±
2YHUDOO:LGWK
(
0ROGHG3DFNDJH:LGWK
(
%6&
2YHUDOO/HQJWK
'
%6&
%6&
&KDPIHURSWLRQDO
K
±
)RRW/HQJWK
/
±
)RRWSULQW
/
5()
)RRW$QJOH
ƒ
±
ƒ
/HDG7KLFNQHVV
F
±
/HDG:LGWK
E
±
0ROG'UDIW$QJOH7RS
ƒ
±
ƒ
0ROG'UDIW$QJOH%RWWRP
ƒ
±
ƒ
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
†6LJQLILFDQW&KDUDFWHULVWLF
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
DS22083A-page 16
© 2008 Microchip Technology Inc.
MCP14628
/HDG3ODVWLF6PDOO2XWOLQH61±1DUURZPP%RG\>62,&@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
© 2008 Microchip Technology Inc.
DS22083A-page 17
MCP14628
NOTES:
DS22083A-page 18
© 2008 Microchip Technology Inc.
MCP14628
APPENDIX A:
REVISION HISTORY
Revision A (March 2008)
• Original Release of this Document.
© 2008 Microchip Technology Inc.
DS22083A-page 19
MCP14628
NOTES:
DS22083A-page 20
© 2008 Microchip Technology Inc.
MCP14628
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
-X
/XX
Device
Temperature
Range
Package
Device
MCP14628
MCP14628T
2A Synchronous Buck Power MOSFET Driver
2A Synchronous Buck Power MOSFET Driver
Tape and Reel
Temperature Range
E
= -40°C to +85°C
Package
MF
SN
= Dual Flat, No Lead (3x3mm Body), 8-Lead
= Plastic SOIC (150 mil Body), 8-Lead
© 2008 Microchip Technology Inc.
Examples:
a)
MCP14628-E/MF:
b)
MCP14628T-E/MF:
c)
MCP14628-E/SN:
d)
MCP14628T-E/SN:
2A Synchronous Driver
8LD DFN Package
Tape and Reel,
2A Synchronous Driver
8LD DFN Package
2A Synchronous Driver
8LD SOIC Package
Tape and Reel,
2A Synchronous Driver
8LD SOIC Package
DS22083A-page 21
MCP14628
NOTES:
DS22083A-page 22
© 2008 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, PRO MATE, rfPIC and SmartShunt are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
FilterLab, Linear Active Thermistor, MXDEV, MXLAB,
SEEVAL, SmartSensor and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, In-Circuit Serial
Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM,
PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo,
PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total
Endurance, UNI/O, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2008, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
© 2008 Microchip Technology Inc.
DS22083A-page 23
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-4182-8400
Fax: 91-80-4182-8422
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
01/02/08
DS22083A-page 24
© 2008 Microchip Technology Inc.