SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor Balanced Series - Modified TO-220 Description The SIDACtor® Balanced Series are designed to protect baseband equipment from damaging overvoltage USBOTJFOUT5IFQBUFOUFEi:wDPOmHVSBUJPOBMTPFOTVSFT balanced overvoltage protection. The series provides a single port through-hole solution that enables voice through DS-1 equipment to comply with various global requlatory standards. Features and Benefits t Low voltage overshoot t Low Capacitance Agency Approvals t Low on-state voltage Agency t Does not degrade with use t Balanced overvoltage protection Agency File Number t Single port protection t Custom lead forms available t Fails short circuit when surged in excess of ratings E133083 Pinout Designation Applicable Global Standards PIN 1 PIN 3 PIN 2 Schematic Symbol 1 3 (T) (R) t TIA-968-A t GR 1089 Intra-building t TIA-968-B t IEC 61000-4-5 t ITU K.20/21 Enhanced Level* t YD/T 1082 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building* *A/B-rated parts require series resistance 2 (G) Electrical Characteristics Part Number Marking VS VDRM VS VDRM @lDRM=5μA @100V/μs @lDRM=5μA @100V/μs V min V max V min Pins 1-2, 3-2 V max Pins 1-3 IS IT mA min mA max A max V max 8 P1553AALxx P1553AA 130 180 130 180 150 800 2.2 P1803AALxx P1803AA 150 210 150 210 150 800 2.2 P2103AALxx P2353AALxx P2703AALxx P3203AALxx P3403AALxx P5103AALxx P1553ABLxx P1803ABLxx P2103ABLxx P2103AA P2353AA P2703AA P3203AA P3403AA P5103AA P1553AB P1803AB P2103AB 170 200 230 270 300 420 130 150 170 250 270 300 350 400 600 180 210 250 170 200 230 270 300 420 130 150 170 250 270 300 350 400 600 180 210 250 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 171 Revised: February 22, 2011 VT@IT= 2.2 Amps IH Capacitance 8 8 8 8 See Capacitance 8 Values table 8 8 8 8 8 Table continues on next page. SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Part Number Marking VS VDRM VS VDRM @lDRM=5μA @100V/μs @lDRM=5μA @100V/μs V min V max V min Pins 1-2, 3-2 P2353ABLxx P2703ABLxx P3203ABLxx P3403ABLxx P5103ABLxx P1553ACLxx P1803ACLxx P2103ACLxx P2353ACLxx P2703ACLxx P3203ACLxx P3403ACLxx P5103ACLxx P2353AB P2703AB P3203AB P3403AB P5103AB P1553AC P1803AC P2103AC P2353AC P2703AC P3203AC P3403AC P5103AC 200 230 270 300 420 130 150 170 200 230 270 300 420 V max Pins 1-3 270 300 350 400 600 180 210 250 270 300 350 400 600 200 230 270 300 420 130 150 170 200 230 270 300 420 270 300 350 400 600 180 210 250 270 300 350 400 600 IH IS IT VT@IT= 2.2 Amps mA min mA max A max V max 150 150 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 8 8 8 8 8 8 8 8 8 8 8 8 8 Capacitance See Capacitance Values table Notes: - Absolute maximum ratings measured at TA= 25ºC. - Devices are bi-directional. - XX Part Number Suffix: ‘RP’ (Reel Pack), Blank (Bulk Pack), or ‘60’ (Type 60 lead form, Bulk Pack) Capacitance Values Part Number P1553AALxx P1803AALxx P2103AALxx P2353AALxx P2703AALxx P3203AALxx P3403AALxx P5103AALxx P1553ABLxx P1803ABLxx P2103ABLxx P2353ABLxx pF Pin 1-2 / 3-2 Tip-Ground, Ring-Ground MIN MAX 10 45 20 40 15 35 15 35 15 35 15 30 15 30 10 60 25 95 25 85 20 85 20 75 pF Pin 1-2 / 3-2 Part Number Tip-Ground, Ring-Ground pF Pin 1-3 Tip-Ring MIN MAX 10 30 10 30 10 25 10 25 10 25 10 20 10 20 10 40 15 60 15 55 10 55 15 50 P2703ABLxx P3203ABLxx P3403ABLxx P5103ABLxx P1553ACLxx P1803ACLxx P2103ACLxx P2353ACLxx P2703ACLxx P3203ACLxx P3403ACLxx P5103ACLxx MIN 20 20 15 15 30 30 30 25 25 25 20 20 MAX 75 70 65 60 95 85 85 75 75 70 65 60 pF Pin 1-3 Tip-Ring MIN 10 10 10 10 20 15 15 15 15 15 15 10 MAX 50 45 45 40 60 55 55 50 50 45 45 40 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings Series IPP 0.2x310 0.5x700 2 2x10 2x10 2 8x20 1.2x50 2 10x160 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min A min 1 1 1 1 ITSM 50/60 Hz di/dt A A min A/μs max A 20 150 150 90 50 75 75 45 75 20 500 B 25 250 250 150 100 100 125 80 100 25 500 C 50 500 400 200 150 200 175 100 200 50 500 Notes: 1 Current waveform in μs 2 Voltage waveform in μs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$ - The device must initially be in thermal equilibrium with -40°C < TJ <¡$ © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 172 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Thermal Considerations Package Symbol Modified TO-220 PIN 1 Value Unit TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C 50 °C/W R0JA PIN 3 PIN 2 Parameter Thermal Resistance: Junction to Ambient V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 td tr t – Time (μs) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 IH 10 8 6 25 °C 4 IH (TC = 25ºC) 12 Ratio of Percent of VS Change – % 14 2 0 -4 -6 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C 173 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed ¡$ Figure 1 TP tP Critical Zone TL to TP Ramp-up TL Temperature Reflow Condition tL TS(max) Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ¡$PS¡$ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling ¡$UP¡$NJOEXFMMVQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45%.FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$3)BUNVQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT ¡$1FBL +&%&$+45%-FWFM UL recognized epoxy meeting flammability classification 94V-0 Body Material Part Marking Part Numbering P xxx 3 A x L xx TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE XXXXXXXXX Blank: Bulk RP: Reel Pack 60: Type 60 Lead Form (for Type 60 orders, contact factory) xxxxx RoHS COMPLIANT IPP RATING © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Part Marking Code (Refer to Electrical Characteristics Table) PACKING STYLE 174 Revised: February 22, 2011 Date Code SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Dimensions - Modified TO-220 A Inches O D Temperature Measurement Point F G P PIN 3 PIN 2 PIN 1 L M K H Tape and Reel Specification — Modified TO-220 Min Max Min A 0.400 0.410 10.16 10.42 D 0.360 0.375 9.14 9.53 F 0.110 0.130 2.80 3.30 G 0.540 0.575 13.71 14.61 H 0.025 0.035 0.63 The modified TO-220 package is designed to meet mechanical standards as set forth in JEDEC publication number 95. 0.240 (6.10) Max J 0.195 0.205 4.95 5.21 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.90 M 0.070 0.085 1.78 2.16 N O P 0.018 0.024 0.46 0.61 0.178 0.290 0.188 0.310 4.52 7.37 4.78 7.87 0.019 (0.5) 1.626 (41.15) 0.720 (18.29) 0.750 ± 0.010 (19.05 ± 0.25) 0.360 (9.14) 0.500 (12.7) A Direction of Feed 1.968 (50.0) Description Packaging Quantity Added Suffix Industry Standard Modified TO-220 Tape and Reel Pack 700 RP EIA-468-B Modified TO-220 Bulk Pack 500 N/A (no suffix required) EIA-468-B Modified TO-220 Type 60 Lead Form Bulk Pack 500 60 (special order item, contact factory for details) N/A © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 0.100 (2.54) Dimensions are in inches (and millimeters). Packing Options Package Type 0.100 (2.54) 14.173 (360.0) 0.89 K N J Millimeters 175 Revised: February 22, 2011