SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor® Balanced Series - MS-013 Description The SIDACtor® Balanced Series MS-013 are designed to protect baseband equipment from overvoltage transients. 5IFQBUFOUFEi:wDPOmHVSBUJPOFOTVSFTCBMBODFE overvoltage protection. The series provides a single port surface mount solution that enables voice through DS-1 equipment to comply with various global requlatory standards. Features and Benefits t Balanced overvoltage protection Agency Approvals t Fails short circuit when surged in excess of ratings t Low voltage overshoot Agency Agency File Number t Low on-state voltage E133083 t Does not degrade with use t Replaces three discrete devices t Meets UL/IEC 60950-1 creepage and clearance Pinout Designation 1 6 2 5 3 4 Applicable Global Standards Schematic Symbol 1 6 2 5 3 4 t TIA-968-A t GR 1089 Intra-building t TIA-968-B t IEC 61000-4-5 t ITU K.20/21 Enhanced Level t YD/T 1082 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building Electrical Characteristics Part Number Part Marking VDRM @lDRM=5μA VS @100V/μs VDRM @lDRM=5μA VS @100V/μs V min V max V min V max Pins 1 & 6-3, 1 & 6-4 P1553UALxx P1803UALxx P2103UALxx P2353UALxx P2703UALxx P3203UALxx P3403UALxx P5103UALxx P1553UA P1803UA P2103UA P2353UA P2703UA P3203UA P3403UA P5103UA 130 150 170 200 230 270 300 420 180 210 250 270 300 350 400 600 Pins 3-4 130 150 170 200 230 270 300 420 180 210 250 270 300 350 400 600 VT IS IT IH V max mA max A max mA min 8 8 8 8 8 8 8 8 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 150 150 150 150 150 150 150 150 Capacitance See Capacitance Values table Table continues on next page. Notes: - Absolute maximum ratings measured at TA$VOMFTTPUIFSXJTFOPUFE - Devices are bi-directional. - XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 148 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Electrical Characteristics (continued) Part Number Part Marking VDRM @lDRM=5μA VS @100V/μs VDRM @lDRM=5μA VS @100V/μs V min V max V min V max Pins 1 & 6-3, 1 & 6-4 P1553UBLxx P1803UBLxx P2103UBLxx P2353UBLxx P2703UBLxx P3203UBLxx P3403UBLxx P5103UBLxx P1553UCLxx P1803UCLxx P2103UCLxx P2353UCLxx P2703UCLxx P3203UCLxx P3403UCLxx P5103UCLxx P1553UB P1803UB P2103UB P2353UB P2703UB P3203UB P3403UB P5103UB P1553UC P1803UC P2103UC P2353UC P2703UC P3203UC P3403UC P5103UC 130 150 170 200 230 270 300 420 130 150 170 200 230 270 300 420 180 210 250 270 300 350 400 600 180 210 250 270 300 350 400 600 Pins 3-4 130 150 170 200 230 270 300 420 130 150 170 200 230 270 300 420 180 210 250 270 300 350 400 600 180 210 250 270 300 350 400 600 VT IS IT IH V max mA max A max mA min 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 Capacitance Capacitance Values Part Number P1553UALxx P1803UALxx P2103UALxx P2353UALxx P2703UALxx P3203UALxx P3403UALxx P5103UALxx P1553UBLxx P1803UBLxx P2103UBLxx P2353UBLxx P2703UBLxx P3203UBLxx P3403UBLxx P5103UBLxx P1553UCLxx P1803UCLxx P2103UCLxx P2353UCLxx P2703UCLxx P3203UCLxx P3403UCLxx P5103UCLxx Pin 3-4 Tip-Ring pF min 20 20 15 15 15 15 15 10 25 25 20 20 20 20 15 15 30 30 30 25 25 25 20 20 pF max 95 85 85 75 75 70 65 60 95 85 85 75 75 70 65 60 95 85 85 75 75 70 65 60 Pins 1 & 6-3, 1 & 6-4 Tip-Ground, Ring-Ground pF min 10 10 10 10 10 10 10 10 15 15 15 15 10 10 10 10 20 15 15 15 15 15 15 10 pF max 60 55 55 50 50 45 45 40 60 55 55 50 50 45 45 40 60 55 55 50 50 45 45 40 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 149 Revised: February 22, 2011 See Capacitance Values table SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/ μs max 45 75 20 500 125 80 100 25 500 175 100 200 50 500 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min A 20 150 150 90 50 75 75 B 25 250 250 150 100 100 C 50 500 400 200 150 200 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPGUP$ - The device must initially be in thermal equilibrium with -40°C < TJ <¡$ 1 Current waveform in μs 2 Voltage waveform in μs Thermal Considerations Package Symbol Parameter Value Unit TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C R0JA Thermal Resistance: Junction to Ambient 60 °C/W Modified MS-013 6 5 4 1 2 3 V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 td tr t – Time (μs) -I Normalized DC Holding Current vs. Case Temperature 10 IH 8 6 25 °C 4 2 IH (TC = 25ºC) 2.0 14 12 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature 0 -4 -6 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 0 20 40 60 80 100 120 140 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. -20 150 Revised: February 22, 2011 160 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Soldering Parameters Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed ¡$ Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ¡$PS¡$ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling ¡$UP¡$NJOEXFMMVQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45%.FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$3)BUNVQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT ¡$1FBL +&%&$+45%-FWFM UL recognized epoxy meeting flammability classification 94V-0 Body Material Part Marking Part Marking Code XXXXXXX (Refer to Electrical Characteristics Table) Date Code XXXXX Part Numbering Packing Options P xxx 3 U x L xx TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKING OPTIONS Package Type RP: Reel Pack TP: Tube Pack RoHS COMPLIANT IPP RATING U Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D TP N/A Modified MS-013 500 6-pin Tube Pack (50 per tube) PACKAGE TYPE © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Description 151 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Dimensions — MS-013 Inches Dimensions A B C D E F G H J K BSC* 0.065 (1.65) Pad Outline C 0.460 (11.68) 0.138 (3.50) Dimension are in inches (and millimeters). 0.059 (1.50) E D 7º TYP J 7º TYP A G H Burr Side 96º A Mold Split Line 4º A 7º TYP BSC* F 7º TYP MIN Length of Flat Detail A K B Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 0.143 * BSC = Basic Spacing between Centers Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .472 (12.0) 12.99 (330) .512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification — MS-013 Message Location .045 (1.14) .310 (7.87) 90˚ .165 (4.19) 6 Interior of the Tube .150 (3.81) .225 (5.72) .525 (13.34) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .005 A .110 (2.79) A Dimensions are in inches (and millimeters) 152 Revised: February 22, 2011 20.000 ± .030 (508.00 ± 0.76) Millimeters Min 3.63