PAM8304 User Guide

PAM8304
EVB User Guide
PAM8304-EV board User Guide
AE Department
1. Revision Information
Date
Revision
Description
2013/5/31
V1.0
Initial release
Comment
This application note contains new product information. Diodes, Inc. reserves the right to modify the product specification without notice.
No liability isassumed as a result of the use of this product. No rights under any patent accompany the sale of the product.
PAM8304
Document number: DSxxxxx Rev. 1 - 0
1 of 5
www.diodes.com
March 2014
© Diodes Incorporated
PAM8304
EVB User Guide
2. Key Features
◆
◆
◆
◆
◆
◆
◆
Supply Voltage from 2.8V to 6.0V
3.0W@10% THD Output with a 4Ω Load at 5V Supply
High Efficiency up to 90% @1W with an 8Ω Speaker
Shutdown Current <1mA
Superior Low Noise without Input
Short Circuit Protection
Thermal Shutdown
3. EV Board Schematic
VDD
VDD
J3
3
2
1
C5
SD
C4
C3
J4
3
2
1
VDD
C1
PVDD
U1
R1
input -
IN-
R2
C2
FB 2
C6
OUT-
SP K
PAM8304
input +
FB 1
IN+
SD
GND
SD
GND
OUT+
C7
Figure 1
4. PAM8304 CB81CA Description
The PAM8304 is a mono filter-less class-D amplifier with high SNR and differential input that eliminate
noise, The filter-less architecture requires no external output filter, fewer external components, less PCB
area and lower system costs, and simplifies application design.
The PAM8304 features short circuit protection and over temperature protection.
Title
Size
B
Date:
File:
2
3
4
5
This application note contains new product information. Diodes, Inc. reserves the right to modify the product specification without notice.
No liability isassumed as a result of the use of this product. No rights under any patent accompany the sale of the product.
PAM8304
Document number: DSxxxxx Rev. 1 - 0
2 of 5
www.diodes.com
March 2014
© Diodes Incorporated
PAM8304
EVB User Guide
5. EV Board View
Input Selection Jump
(Differential or single-ended)
Power In: 2.8V-6V
Audio Input
Speaker Output
Enable control Selection Jump
EV board operational sequence:
a.
b.
c.
d.
e.
f.
Preset the power supply to between 2.8V and 6V.
Turn off the power supply.
Connect power supply to EV board power.
Connect audio input from audio input jack.
Connect the Speaker to the output jack
Turn on the power supply
This application note contains new product information. Diodes, Inc. reserves the right to modify the product specification without notice.
No liability isassumed as a result of the use of this product. No rights under any patent accompany the sale of the product.
PAM8304
Document number: DSxxxxx Rev. 1 - 0
3 of 5
www.diodes.com
March 2014
© Diodes Incorporated
PAM8304
EVB User Guide
6. EV Board BOM List
Item
Value
C1,C2
0.1uF
C3
1uF
C4
1uF
C5
10uF
Type
X5R/X7R,
Ceramic/0603
X5R/X7R,
Ceramic/0603
X5R/X7R,
Ceramic/0603
X5R/X7R,
Ceramic/0805
R1,R2
0603
IC1
PAM8304
Rating
Description
10V
Input coupling CAP
16V
PVDD decoupling CAP
16V
VDD decoupling CAP
10V
PVDD decoupling CAP
Vender and port
Taiyo Yuden
HMK107BJ104KA-T
Taiyo Yuden
EMK107B7105KA-T
Taiyo Yuden
EMK107B7105KA-T
Taiyo Yuden
LMK107BBJ106MALT
Input coupling resistance
PAM
7. External Components Selection
Input Capacitors (C1,C2)
(1). Form a high pass filter with Ri, and the cut off frequency is fc=1/2∏Ri*Ci
(2). Have a tolerance of 10% or better for matching: any mismatch in capacitance
causes an importance mismatch at the corner frequency.
(3). Low leakage current needed, 0.1uF, X5R/X7R ceramic
Power Supply decoupling Caps (C3, C4)
(1). Low ESR for good THD, PSRR
(2).C3,C4, Additional 1uF or greater for low frequency noise filtering and serves as a local storage
capacitor for supplying current during large signal transients on the amplifier outputs
(3).Need place very closed to the IC
8. PCB Layout Guidelines
Grounding
(1). Use plane grounding or separate grounds.
(2). Do not use one line connecting power GND and analog GND
(3). Output noise grounds must tie to system ground at the power in exclusively.
(4). Signal currents for the inputs need to be returned to quite ground.
This ground only ties to the signal components and the GND pin.
Power Supply
(1) VDD and PVDD need to be separated and tied together at the system power supply.
(2) Recommend that the all the trace could be routed as short and thick as possible.
(3) Any barricade placed in the trace could result in the bad performance of the amplifier.
This application note contains new product information. Diodes, Inc. reserves the right to modify the product specification without notice.
No liability isassumed as a result of the use of this product. No rights under any patent accompany the sale of the product.
PAM8304
Document number: DSxxxxx Rev. 1 - 0
4 of 5
www.diodes.com
March 2014
© Diodes Incorporated
PAM8304
EVB User Guide
Components Placement
(1). The power supply capacitors (C3,C4) need to place very close to the PAM8304’s pins.
(2). Input capacitors (C1,C2) place closed to input pin as near as possible
8. PCB Layout Example
Top Layer
Bottom Layer
This application note contains new product information. Diodes, Inc. reserves the right to modify the product specification without notice.
No liability isassumed as a result of the use of this product. No rights under any patent accompany the sale of the product.
PAM8304
Document number: DSxxxxx Rev. 1 - 0
5 of 5
www.diodes.com
March 2014
© Diodes Incorporated