A Product Line of Diodes Incorporated PAM2308 DUAL HIGH-EFFICIENCY PWM STEP-DOWN DC-DC CONVERTER Description Pin Assignments The PAM2308 is a dual step-down current-mode, DC-DC converter. At heavy load, the constant frequency PWM control performs excellent stability and transient response. To ensure the longest battery life in portable applications, the PAM2308 provides a powersaving Pulse- Skipping Modulation (PSM) mode to reduce quiescent current under light load operation. The PAM2308 supports a range of input voltages from 2.5V to 5.5V, allowing the use of a single Li+/Li-polymer cell, multiple Alkaline/NiMH cell, USB, and other standard power sources. The dual output voltages are available for 3.3V, 2.8V, 2.5V, 1.8V, 1.5V, 1.2V or adjustable. All versions employ internal power switch and synchronous rectifier to minimize external part count and realize high efficiency. During shutdown, the input is disconnected from the output and the shutdown current is less than 0.1µA. Other key features include under-voltage lockout to prevent deep battery discharge. Features • Efficiency up to 96% • Only 40μA (typ per channel) Quiescent Current • Output Current: Up to 1A per Channel • Internal Synchronous Rectifier • 1.5MHz Switching Frequency • Soft-Start • Under-Voltage Lockout • Short Circuit Protection • Thermal Shutdown • Small WDFN3x3-10L Packages • Pb-Free Package and RoHS Compliant Applications • Cellular Phone • Portable Electronics • Personal Information Appliances • Wireless and DSL Modems • MP3 Players Typical Applications Circuit Rx1 ⎞ ⎛ ⎟ Figure 1. Adjustable Voltage Regulator V OUTx = VREF ⎜1 + Rx2 ⎠ ⎝ PAM2308 Document number: DSxxxxx Rev. 1 - 1 1 of 15 www.diodes.com January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Typical Applications Circuit (cont.) VOUTx = 1.2V, 1.5V, 1.8V, 2.5V, 2.8V or 3.3V Figure 2. Fixed Voltage Regulator Pin Descriptions Pin Name Pin Number EN1 FB1 VIN2 1 2 3 GND 4, 9 LX2 EN2 FB2 VIN1 LX1 5 6 7 8 10 PAM2308 Document number: DSxxxxx Rev. 1 - 1 Function Chip Enable of Channel 1(Active High). VEN1 ≤ VIN1. Feedback of Channel 1. Power Input of Channel 2. Ground. The exposed pad must be soldered to a large PCB and connected to GND for maximum power dissipation. Pin for Switching of Channel 2. Chip Enable of Channel 2 (Active High).VEN2 ≤ VIN2. Feedback of Channel 2. Power Input of Channel 1. Pin for Switching of Channel 1. 2 of 15 www.diodes.com January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Functional Block Diagram Absolute Maximum Ratings (@TA = +25°C, unless otherwise specified.) These are stress ratings only and functional operation is not implied. Exposure to absolute maximum ratings for prolonged time periods may affect device reliability. All voltages are with respect to ground. Parameter Input Voltage EN1, FB1, LX1, EN2, FB2 AND LX2 Pin Voltage Maximum Junction Temperature Storage Temperature Range Soldering Temperature Rating -0.3 to +6.5 Unit V -0.3 to (VIN +0.3) 150 -65 to +150 260, 10sec V °C °C °C Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.) Parameter Supply Voltage Ambient Temperature Range Junction Temperature Range Rating 2.5 to 5.5 -40 to +85 -40 to +125 Unit V °C Thermal Information Parameter Symbol Package Max Thermal Resistance (Junction to Ambient) θJA W-DFN3x3-10 60 Thermal Resistance (Junction to Case) θJC W-DFN3x3-10 8.5 Thermal Resistance (Junction to Case) PD W-DFN3x3-10 1.66 PAM2308 Document number: DSxxxxx Rev. 1 - 1 3 of 15 www.diodes.com Unit °C/W W January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Electrical Characteristics (@TA = +25°C, VIN = 3.6V, VO = 1.8V, CIN = 10µF, CO = 10µF, L = 2.2µH, unless otherwise specified.) Parameter Symbol Test Conditions Min Input Voltage Range VIN 2.5 Regulated Feedback Voltage VFB 0.588 Reference Voltage Line Regulation ΔVFB Regulated Output Voltage Accuracy VO Peak Inductor Current IPK Typ 0.6 Max V 0.612 V 0.3 -3 IO = 100mA %/V +3 1.5 VIN = 3V, VFB = 0.5V or VO = 90% Units 5.5 % A Output Voltage Line Regulation LNR VIN = 2.5V TO 5V, IO = 10mA 0.2 0.5 Output Voltage Load Regulation LDR IO = 1mA to 1A 0.5 1.5 % Quiescent Current (per channel) IQ No load 40 70 µA Shutdown Current (per channel) ISD VEN = 0V Oscillator Frequency Drain-Source On-State Resisitance SW Leakage Current fosc RDS(ON) High Efficiency ILSW η EN Threshold High VEH EN Threshold Low VEL EN Leakage Current IEN OTP OTH Over Temperature Protection OTP Hysteresis PAM2308 Document number: DSxxxxx Rev. 1 - 1 1.2 VO = 100% IDS = 100mA 0.1 1 µA 1.5 1.8 MHz 500 VFB = 0V or VO = 0V P MOSFET N MOSFET kHz 0.3 0.35 0.45 0.5 Ω Ω ±0.01 1 µA 96 % 1.5 V 0.3 4 of 15 www.diodes.com %/V V ±0.01 µA 150 30 °C °C January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Typical Performance Characteristics (@TA = +25°C, CIN = 10µF, CO = 10µF, L = 4.7µH, unless otherwise specified.) PAM2308 Document number: DSxxxxx Rev. 1 - 1 5 of 15 www.diodes.com January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Typical Performance Characteristics (cont.) (@TA = +25°C, CIN = 10µF, CO = 10µF, L = 4.7µH, unless otherwise specified.) PAM2308 Document number: DSxxxxx Rev. 1 - 1 6 of 15 www.diodes.com January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Typical Performance Characteristics (cont.) (@TA = +25°C, CIN = 10µF, CO = 10µF, L = 4.7µH, unless otherwise specified.) PAM2308 Document number: DSxxxxx Rev. 1 - 1 7 of 15 www.diodes.com January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Typical Performance Characteristics (cont.) (@TA = +25°C, CIN = 10µF, CO = 10µF, L = 4.7µH, unless otherwise specified.) PAM2308 Document number: DSxxxxx Rev. 1 - 1 8 of 15 www.diodes.com January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Typical Performance Characteristics (cont.) (@TA = +25°C, CIN = 10µF, CO = 10µF, L = 4.7µH, unless otherwise specified.) PAM2308 Document number: DSxxxxx Rev. 1 - 1 9 of 15 www.diodes.com January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Application Information The basic PAM2308 application circuit is shown on Page 1 and 2. External component selection is determined by the load requirement, selecting L first and then CIN and COUT. Inductor Selection For most applications, the value of the inductor will fall in the range of 1μH to 4.7μH. Its value is chosen based on the desired ripple current. Large value inductors lower ripple current and small value inductors result in higher ripple currents. Higher VIN or VOUT also increases the ripple current as shown in Equation 1. A reasonable starting point for setting ripple current is ΔIL = 400mA (40% of 1A). ΔIL = ⎛ ⎞ ⎜1 − V OUT ⎟ ⎟ VIN ⎠ 1 Equation (f )(L ) VOUT ⎜⎝ (1) The DC current rating of the inductor should be at least equal to the maximum load current plus half the ripple current to prevent core saturation. Thus, a 1.4A rated inductor should be enough for most applications (1A + 400mA). For better efficiency, choose a low DC-resistance inductor. VO L 1.2V 1.5V 1.8V 2.5V 3.3V 2.2µH 2.2µH 2.2µH 4.7µH 4.7µH CIN and COUT Selection In continuous mode, the source current of the top MOSFET is a square wave of duty cycle VOUT/VIN. To prevent large voltage transients, a low ESR input capacitor sized for the maximum RMS current must be used. The maximum RMS capacitor current is given by: CIN required IRMS ≅ IOMAX [VOUT (VIN − VOUT )]1/ 2 VIN This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT /2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that the capacitor manufacturer's ripple current ratings are often based on 2000 hours of life. This makes it advisable to further derate the capacitor, or choose a capacitor rated at a higher temperature than required. Consult the manufacturer if there is any question. The selection of COUT is driven by the required effective series resistance (ESR). Typically, once the ESR requirement for Cout has been met, the RMS current rating generally far exceeds the IRIPPLE (P-P) requirement. The output ripple ΔVOUT is determined by: ⎛ 1 ⎞ ⎟ ΔV OUT ≈ ΔIL ⎜⎜ ESR + 8fCOUT ⎟⎠ ⎝ Where f = operating frequency, COUT =output capacitance and ΔIL = ripple current in the inductor. For a fixed output voltage, the output ripple is highest at maximum input voltage since ΔIL increases with input voltage. Using Ceramic Input and Output Capacitors Higher values, lower cost ceramic capacitors are now becoming available in smaller case sizes. Their high ripple current, high voltage rating and low ESR make them ideal for switching regulator applications. Using ceramic capacitors can achieve very low output ripple and small circuit size. When choosing the input and output ceramic capacitors, choose the X5R or X7R dielectric formulations. These dielectrics have the best temperature and voltage characteristics of all the ceramics for a given value and size. Thermal Consideration Thermal protection limits power dissipation in the PAM2308. When the junction temperature exceeds +150°C, the OTP (Over Temperature Protection) starts the thermal shutdown and turns the pass transistor off. The pass transistor resumes operation after the junction temperature drops below +120°C. For continuous operation, the junction temperature should be maintained below 125°C. The power dissipation is defined as: PD = IO 2 V O RDS(ON)H + (VIN − V O )RDS( ON)L VIN + (tSW FS IO + IQ ) VIN IQ is the step-down converter quiescent current. The term tsw is used to estimate the full load step-down converter switching losses. PAM2308 Document number: DSxxxxx Rev. 1 - 1 10 of 15 www.diodes.com January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Application Information (cont.) For the condition where the step-down converter is in dropout at 100% duty cycle, the total device dissipation reduces to: PD = IO 2 RDS(ON)H + IQ VIN Since RDS(ON), quiescent current, and switching losses all vary with input voltage, the total losses should be investigated over the complete input voltage range. The maximum power dissipation depends on the thermal resistance of IC package, PCB layout, the rate of surrounding airflow and temperature difference between junction and ambient. The maximum power dissipation can be calculated by the following formula: PD = T J(MAX ) − T A θJA Where TJ(MAX) is the maximum allowable junction temperature +125°C. TA is the ambient temperature and θJA is the thermal resistance from the junction to the ambient. Based on the standard JEDEC for a two layers thermal test board, the thermal resistance θJA of W-DFN3X3 is 60°C/W. The maximum power dissipation at TA = +25°C can be calculated by following formula: P = (125°C - 25°C) /60°C/W = 1.66W Setting the Output Voltage The internal reference is 0.6V (Typical). The output voltage is calculated as below: R1 ⎞ ⎛ ⎟ V O = 0 .6 x ⎜ 1 + R 2⎠ ⎝ The output voltage is given by Table 1. Table 1: Resistor selection for output voltage setting. VO R1 R2 1.2V 1.5V 1.8V 2.5V 3.3V 100k 150k 200k 380k 540k 100k 100k 100k 120k 120k 100% Duty Cycle Operation As the input voltage approaches the output voltage, the converter turns the P-Channel transistor continuously on. In this mode the output voltage is equal to the input voltage minus the voltage drop across the P-Channel transistor: V OUT = VIN − ILOAD (RDSON + RL ) where RDS(ON) = P-Channel switch ON resistance, ILOAD = Output Current, RL = Inductor DC Resistance UVLO and Soft-Start The reference and the circuit remain reset until the VIN crosses its UVLO threshold. The PAM2308 has an internal soft-start circuit that limits the in-rush current during start-up. This prevents possible voltage drops of the input voltage and eliminates the output voltage overshoot. The soft-start acts as a digital circuit to increase the switch current in several steps to the P-Channel current limit (1500mA). Short Circuit Protection The switch peak current is limited cycle-by-cycle to a typical value of 1500mA. In the event of an output voltage short circuit, the device operates with a frequency of 400kHz and minimum duty cycle, therefore the average input current is typically 200mA. Thermal Shutdown When the die temperature exceeds +150°C, a reset occurs and the reset remains until the temperature decrease to +120°C, at which time the circuit can be restarted. PAM2308 Document number: DSxxxxx Rev. 1 - 1 11 of 15 www.diodes.com January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Application Information (cont.) PCB Layout Check List When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the PAM2308. These items are also illustrated graphically in Figure 1. Check the following in your layout: 1. The power traces, consisting of the GND trace, the SW trace and the VIN trace should be kept short, direct and wide. 2. Does the FB pin connect directly to the feedback resistors? The resistive divider R1/R2 must be connected between the (+) plate of COUT and ground. 3. Does the (+) plate of CIN connect to VIN as closely as possible? This capacitor provides the AC current to the internal power MOSFETs. 4. Keep the switching node, SW, away from the sensitive FB node. 5. Keep the (–) plates of CIN and COUT as close as possible. Top Bottom Figure 1. PAM2308 Suggested Layout PAM2308 Document number: DSxxxxx Rev. 1 - 1 12 of 15 www.diodes.com January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Ordering Information Part Number Part Marking Package Type Standard Package PAM2308BYMv1v2 2308v1v2 XXXYW W-DFN3x3-10 3000 Units/Tape & Reel Marking Information PAM2308 Document number: DSxxxxx Rev. 1 - 1 13 of 15 www.diodes.com January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 Package Outline Dimensions (All dimensions in mm.) W-DFN3x3-10 PAM2308 Document number: DSxxxxx Rev. 1 - 1 14 of 15 www.diodes.com January 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM2308 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2013, Diodes Incorporated www.diodes.com PAM2308 Document number: DSxxxxx Rev. 1 - 1 15 of 15 www.diodes.com January 2013 © Diodes Incorporated