X

DT6360STC
DUAL TEC® MOTION SENSOR
X-BAND TECHNOLOGY
Microcontroller-based, ceiling mount DUAL TEC Motion Sensor. All the advantages of DUAL TEC motion sensor accuracy
and reliability in a desirable ceiling mount design.
FEATURES
• Microwave Advanced Processing
(MAP)
Incoming microwave and PIR
signals are constantly monitored
and individually qualified for intrusion
characteristics. The timing and
sequence of each of these signals
must be qualified by MAP settings
to specific environments, allowing
for optimum catch performance and
false alarm immunity.
• Microwave/PIR Technology
The use of dual technology provides
the best detection available while
virtually eliminating false alarms and
costly service calls.
• Built-in Diagnostics and
Supervision
Allows trouble conditions to be quickly
identified, diagnosed and corrected.
• Ceiling Mount Design
360° field-of-view, mounting height
from 8' to 16' (2.4m to 4.9m), install
as recessed or surface mount.
• Microcontroller-initiated Self-tests
Microcontroller automatically initiates
self-tests at power-up, trouble
conditions and programmed intervals.
• Trouble Output
After a trouble is confirmed with
a self-test, the trouble output can
be used to annunciate the trouble
condition.
• Full Supervision Microwave/PIR
– Patented INFORMER® circuit
constantly monitors microwave
and PIR against blockage and
misapplication.
– Independent circuit supervises both
microwave and PIR against failure;
at a loss of signal, microcontroller
initiates self-test and unit switches
automatically to single technology
operation.
• Mounting
Surface or flush mount on ceilings
(flush mount kit included); maximum
standard range obtained at 11' (3.4m).
PIR mirror assembly included for
installation on 12' to 16' (3.7m to
4.9m) ceilings.
SPECIFICATIONS
• Physical Dimensions
– White, high impact, ABS plastic
housing
– 5" H x 5" W x 2.3" D
(12.7cm x 12.7cm x 5.8cm)
– Weight: 14 oz (397 g)
• Power Requirements
– 10 – 14.5VDC
– 40mA, 12VDC typical
• Trouble Output
– Open collector: voltage between
collector and emitter (Vce) is 0.3V
@ 50mA
• Alarm Relay
– Energized Form C: (N.O./N.C.)
reed relay rated 125mA at 25VDC
• Command Output
– Self-test initiate
Active: 0 – 1.5V (low)
Inactive: 6 – V+ (high)
Impedance: 110K (minimum)
• Microwave Frequencies
– 10.525 GHz (USA)
• Tamper Switch
– Ceiling and cover tamper switches;
Form A (N.C.) switch rated 25mA,
30VDC
• Operating Temperature
– 32° – 120° F (0° – 49° C); 5% to
95% relative humidity, noncondensing
• RFI Immunity
– 30 Vm, from 10 MHz – 1000 MHz
• PIR White Light Immunity
– 900 LUX
• Detection Range
– 50' (15m) diameter, 25' (7.6m) radius
• PIR Fields of View
– 8'–11' mirror assembly (three 360° fields)
Long range: 36
Lower: 16
Intermediate: 24
Look-down: 1
– 12'–16' mirror assembly (two 360° fields)
Long range: 40
Intermediate: 20
Look-down: 1
• Sensitivity
– 2–4 steps within field of view
• Approvals/Listings
– FCC certified, UL listed, ULC,
IC certified, C-Tick
DT6360STC
DUAL TEC® MOTION SENSOR X-BAND TECHNOLOGY
DETECTION PATTERNS
MECHANICAL MOUNTING SPECIFICATIONS
6.80
(17.3)
4 MOUNTING HOLES FOR #6 PAN HEAD SCREWS
FOR RECESS CEILING MOUNTING APPLICATIONS
6.80
(17.3)
2.40
(6.1)
5.37
(13.7)
6.00
(15.2)
2.15
(5.5)
5.37
(13.7)
0.09
(0.2)
3.00
(7.6)
2 SURFACE MOUNTING
LOCATIONS FOR #6 PAN
HEAD SCREWS
0.09
(0.2)
3.30
(8.4)
DIMENSIONS: INCHES [CENTIMETERS]
VIEW SHOWING INSIDE OF BACK COVER WITH
PCB ASSY AND FRONT COVER ASSY REMOVED
ORDERING
DT6360STC
DUAL TEC Motion Sensor
Automation and Control Solutions
Honeywell Security & Communications
2 Corporate Center Dr. Suite 100
P.O. Box 9040
Melville, NY 11747
www.honeywell.com
L/DT6360/D
September 2008
© 2008 Honeywell International Inc.
DRAWING VIEW SHOWING INSIDE
OF RECESS CEILING MOUNT BUCKET