For more information, please visit the product page. date 01/17/2013 page 1 of 7 SERIES: VDRS-150 │ DESCRIPTION: AC-DC DIN RAIL FEATURES • • • • • • • • • • up to 150 W continuous power universal input (88~264 Vac / 124~373 Vdc) 150% peak load capability2 DIN Rail power supplies two peak load mode selector built-in remote ON/OFF function over voltage, over load, and over temperature protections UL 508 and TUV safety approvals built-in active PFC function (PF 0.90 at 115 Vac, 0.98 at 230 Vac) efficiency up to 87% output voltage output current output power ripple and noise1 (Vdc) max (A) max (W) max (mVp-p) (%) VDRS-150-24 24 6.3 150 240 87 VDRS-150-48 48 3.2 150 480 87 MODEL Note: 1. at full load, 230 Vac input, measured at 20MHz bandwidth with a 47 μF and 0.1 μF parallel cap on the output 2. 3 seconds or 20% duty cycle max. The average output power should not exceed the rated power. PART NUMBER KEY VDRS - 150 - XX Base Number Output Voltage cui.com efficiency For more information, please visit the product page. CUI Inc │ SERIES: VDRS-150 │ DESCRIPTION: AC-DC DIN RAIL date 01/17/2013 │ page 2 of 7 INPUT parameter conditions/description min voltage frequency max units 88 124 typ 264 373 Vac Vdc 47 63 Hz current at 115 Vac at 230 Vac 2.6 1.3 A A inrush current at 115 Vac at 230 Vac 33 65 A A power factor correction at 230 Vac at 115 Vac 0.90 0.98 leakage current at 240 Vac 1 mA max units ±1 % OUTPUT parameter conditions/description min typ voltage accuracy line regulation load regulation 5 temperature coefficient (0 ~ 50°C) hold-up time at 115 / 230 Vac, cold start % ±1 % ±0.03 %/°C 16 voltage adjustment range Note: ±0.5 ms -2 +8 % 1. All specification are measured at 230 Vac input, rated load, 25°C unless otherwise specified. PROTECTIONS parameter conditions/description latch-off mode, restart to recover from fault over voltage protection min 24 V model 48 V model max units 120 117 typ 138 135 % % 150 % 100 °C 60 30 Vdc Vdc Kicks in between 105~150% rated output power when the fault persist for about 3 sec, then clamps output voltage down, automatic recovery’ >150% rated power or short circuit would cause the power supply to go in to constant current limiting; if fault condition is not removed after 5 times, then the converter will shutdown and need to be restarted to recover from fault. over load protection constant current limiting, automatically recovers after fault condition is removed 105 over temperature protection output shut down and auto restart upon reduction of temperature 90 DC ok relay contact ratings at 0.3 A at 1 A and 0.5 A cui.com 95 For more information, please visit the product page. CUI Inc │ SERIES: VDRS-150 │ DESCRIPTION: AC-DC DIN RAIL date 01/17/2013 │ page 3 of 7 SAFETY & COMPLIANCE parameter conditions/description isolation voltage input to output for 1 minute input to case for 1 minute output to case, output to DC OK for 1 minute isolation resistance input to output, input to case, output to case, 500 Vdc safety approvals UL 508, TUV EN 60950-1 EMI/EMC2 EN 55022 (CISPR22) Class B, EN 61000-3-(2, 3), EN 61000-4-(2,3,4,5,6,8,11) ENV 50204, EN 55024, EN 61000-6-2 (EN50082-2), EN 61204-3, heavy industry level, criteria A, meet SEMI F47 RoHS compliant yes Note: min typ max units 4,242 2,121 707 Vdc Vdc Vdc 100 MΩ 2. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. ENVIRONMENTAL parameter conditions/description min operating temperature storage temperature operating humidity non-condensing storage humidity vibration typ max units -10 70 °C -40 85 °C 20 90 % 10 (10 ~ 500 Hz, 1 hour per axis, 3 hours total) cui.com 95 2 % Grms For more information, please visit the product page. CUI Inc │ SERIES: VDRS-150 │ DESCRIPTION: AC-DC DIN RAIL date 01/17/2013 │ page 4 of 7 MECHANICAL parameter conditions/description dimensions 2.185 x 4.921 x 3.929 (55.5 x 125 x 99.8 mm) min typ max inch MECHANICAL DRAWING CN1 1 FG 2 ac line 3 ac neutral CN2 1 DC+ 2 DC- 3 INH+ 4 INH- 5 relay contact 6 relay contact 55.5 99.8 123456 CN2 Relay Contact + +V ADJ. peak load setting 2 remote on/off setting OFF 1 2 3 CN1 35 1 ON SW1 SW2 Admissible DIN-RAIL: TS35/7.5 or TS35/15 cui.com 125 DC ON Switch units For more information, please visit the product page. CUI Inc │ SERIES: VDRS-150 │ DESCRIPTION: AC-DC DIN RAIL date 01/17/2013 │ page 5 of 7 PEAK LOADING SW1 ON (MODE1) DEFAULT SETTING I T-peak I-peak T-peak presents while the unit is working within 110%~150% raterd output power. See Curve “B” for the variation in T-Peak between output current and hold-up time. If T-peak is more than the time setting in Curve “B”, the output current will drop to the constant limit (I-normal) that is 105% of the rated power. Meanwhile, I-normal and T-normal will be presenting. See Curve “A” for the timing back to I-Peak of T-normal and this mode can be used for easy 2-stage battery chargers. I-normal T-normal 0 T PEAK LOADING SW1 OFF (MODE2) I T-peak I-peak T-peak presents while the unit is working within 110%~150% rated output power. See Curve “B” for the variation of T-peak between output current and hold-up time. If T-peak is more than the time setting in Curve “B”, the output voltage sill be shut down for 3~4 seconds and then auto-recover. 0 3 ~ 4 sec T T-normal T-peak 24 22 20 18 16 14 12 10 8 6 4 2 0 22 20 18 16 14 12 10 8 6 4 2 0 10% 20% 30% 40% 50% 60% 70% 80% 90% I-normal 110% 115% 120% 125% 130% 135% 140% 145% 150% I-peak CURVE A CURVE B cui.com For more information, please visit the product page. CUI Inc │ SERIES: VDRS-150 │ DESCRIPTION: AC-DC DIN RAIL date 01/17/2013 │ page 6 of 7 REMOTE ON/OFF The power supply can be turned on/off by using the “remote control” function. SW SW2 INH+(3 PIN)/INH-(4 PIN) Output Status off SW ON (>2.5 V) ENABLE off SW OFF (<0.8 V) DISABLE on SW ON (>2.5 V) DISABLE on SW OFF (<0.8 V) ENABLE External Power Source I = 6 ~ 20mA 123456 CN2 (default setting) Relay Contact + +V ADJ. DC ON ON OFF SW1 SW2 DERATING CURVE Output power vs. Ambient temperature for 3 sec. typ. 125 112.5 100 100 Load ( %) Load ( %) 150 Output power vs. Input Voltage continuous 80 60 50 40 80 60 40 20 0 -10 0 10 20 30 88 40 50 60 70 100 120 Input Voltage (Vac) 60 Hz Ambient temperature (°C) Note: 110 1. Derating may be needed under low input voltage. Please check the derating curve for more details. ACTIVE DC SIGNAL - RELAY CONTACT Contact Close When the output voltage reaches the adjusted output voltage Contact Open When the output voltage drops below 45% Contact Ratings (MAX) 30 V / 1 A resistive load cui.com 264 For more information, please visit the product page. CUI Inc │ SERIES: VDRS-150 │ DESCRIPTION: AC-DC DIN RAIL date 01/17/2013 │ page 7 of 7 REVISION HISTORY rev. description date 1.0 initial release 10/17/2012 1.01 spec. update 11/07/2012 1.02 spec. update 01/17/2013 The revision history provided is for informational purposes only and is believed to be accurate. Headquarters 20050 SW 112th Ave. Tualatin, OR 97062 800.275.4899 Fax 503.612.2383 cui.com [email protected] CUI offers a two (2) year limited warranty. Complete warranty information is listed on our website. CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use. CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.