DFM (Military M83401/03) www.vishay.com Vishay Dale Thick Film Resistor Networks, Military, MIL-PRF-83401 Qualified, Type RZ030, Flat Pack FEATURES • • • • • Isolated, bussed and dual terminator schematics available Hot-solder dipped leads MIL-PRF-83401 qualified Thick film resistive elements TCR available in “K” (± 100 ppm/°C) or “M” (± 300 ppm/°C) characteristic • 100 % screen tested per group A, subgroup 1 of MIL-PRF-83401 • 0.065" (1.65 mm) height for high density packaging STANDARD ELECTRICAL SPECIFICATIONS POWER POWER TEMPERATURE MIL RATING VISHAY DALE RATING RESISTANCE MIL TOLERANCE (2) COEFFICIENT (1) WEIGHT SPEC. SCHEMATIC ELEMENT PACKAGE MODEL/ RANGE STYLE g ±% (-55 °C to +125 °C) SHEET P70 °C PIN NO. P70 °C ± ppm/°C W W 11 (A) DFM14 RZ030 03 0.050 0.350 10 to 1M 12 (B) 0.025 0.325 10 to 1M 15 (J) 0.015 0.350 Consult factory 1, 2, 5 100, 300 0.4 Notes • Consult factory for stocked values. (1) K = ± 100 ppm/°C; M = ± 300 ppm/°C. (2) ± 2 % standard, ± 1 % and ± 5 % available. GLOBAL PART NUMBER INFORMATION New Global Part Numbering: M8340103M6801GAD05 (preferred part numbering format) M 8 3 4 0 1 0 MIL STYLE SPEC SHEET CHARACTERISTIC M83401 03 K = 100 ppm M = 300 ppm 3 M 6 RESISTANCE VALUE 3 digit significant figure, followed by a multiplier 10R0 = 10 3302 = 33 k 1004 = 1 M 8 0 1 G A D 0 5 TOLERANCE SCHEMATIC PACKAGING F=±1% G=±2% J=±5% A = Isolated B = Bussed D05 = Tin/lead, tube DSL = Tin/lead, tube, single lot date code Historical Part Number Example: M8340103M6801GA (will continue to be accepted) M83401 03 M 6801 G A D05 MIL STYLE SPEC SHEET CHARACTERISTIC RESISTANCE VALUE TOLERANCE SCHEMATIC PACKAGING New Global Part Numbering: M8340103KA001GJD05 (preferred part numbering format) M 8 3 4 0 1 0 3 K A 0 0 1 G J D 0 5 MIL STYLE SPEC SHEET CHARACTERISTIC RESISTANCE VALUE TOLERANCE SCHEMATIC PACKAGING M83401 03 K = 100 ppm M = 300 ppm Per Std. MIL. Spec. (see Impedance Codes table) F=±1% G=±2% J=±5% J = Dual terminator D05 = Tin/lead, tube DSL = Tin/lead, tube, single lot date code Historical Part Number Example: M8340103KA001GJ (will continue to be accepted) M83401 MIL STYLE 03 SPEC SHEET M A001 G J D05 CHARACTERISTIC RESISTANCE VALUE TOLERANCE SCHEMATIC PACKAGING Note • For additional information on packaging, refer to the Surface Mount Network Packaging document (www.vishay.com/doc?31540). Revision: 12-Sep-13 Document Number: 31517 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DFM (Military M83401/03) www.vishay.com Vishay Dale DIMENSIONS in inches (millimeters) Pin #1 0.250 (6.35) Min. 0.050 (1.27) Typ. 0.365 (9.27) Min. 0.385 (9.78) Max. 0.075 (1.91) Max. 0.019 ± 0.006 (0.483 ± 0.15) 12 Schematic DFM1411 Package 0.350 0.200 15 Schematic Power Rating (W) Power Rating (W) Power Rating (W) 0.400 0.400 DFM1412 Package 0.325 Single Resistor DFM1415 Package 0.350 Single Resistor 0.050 0.025 Derating 0.400 0.200 0.200 - 55 0.005 + 0.004 - 0.002 (0.127 + 0.102 - 0.051) 0.825 (20.96) Max. 0.305 (7.75) Max. 11 Schematic 0.250 (6.35) Min. + 25 + 70 + 125 + 150 Single Resistor 0.015 - 55 + 25 + 70 + 125 + 150 - 55 + 25 Ambient Temperature °C Ambient Temperature °C + 70 + 125 + 150 Ambient Temperature °C MECHANICAL SPECIFICATIONS Marking resistance to solvents Permanency testing per MIL-PRF-83401 Solderability Per MIL-PRF-83401 Per MIL-STD-1276 DFM1411, DFM1412 and DFM1415 = Type G (hot solder dipped) Hot solder dipped leads supplied as standard finish Terminals Body Epoxy filled ceramic sandwich TECHNICAL SPECIFICATIONS PARAMETER UNIT MDM SERIES Maximum operating voltage VDC 50 Voltage coefficient of resistance Veff < 50 ppm Dielectric strength VAC 100 min. Insulation resistance 10 000M Operating temperature range °C -55 to +125 Storage temperature range °C -55 to +150 IMPEDANCE CODES CODE R1 () R2 () CODE R1 () A001 82 130 A010 330 470 A002 120 200 A011 330 680 A003 130 210 A012 1.5K 3.3K A004 160 260 A013 3K 6.2K A005 180 240 A014 180 270 A006 180 390 A015 270 270 A007 220 270 A016 560 560 A008 220 330 A017 560 1.2K A009 330 390 A018 620 2.7K Revision: 12-Sep-13 R2 () Document Number: 31517 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DFM (Military M83401/03) www.vishay.com Vishay Dale CIRCUIT APPLICATIONS 11 Schematic DFM1411 (M8340103xxxxxxA) 7 isolated resistors The DFM1411 provides the user with 7 nominally equal resistors with each resistor isolated from all others. Commonly used in the following applications: DFM1411 • “Wired OR” pull-up • Power driven pull-up • TTL input pull-down Pin #1 • Line termination • ECL output pull-down • Long-line impedance balancing • LED current limiting • Power gate pull-up 12 Schematic DFM1412 (M8340103xxxxxxB) 13 resistors with one pin common • • • • • • • The DFM1412 provides the user with a choice of 13 nominally equal resistors, each connected to a common pin. Commonly used in the following applications: • MOS/ROM pull-up/pull-down • “Wired OR” pull-up • Open Collector pull-up • Power driven pull-up • TTL unused gate pull-up DFM1412 Pin #1 • Digital pulse squaring • TTL input pull-down • High speed parallel pull-up 15 Schematic 14 R1 R1 R2 R1 1R2 R1 R2 R1 R2 R1 R1 R2 R1 R2 R2 R1 R2 R1 R2 DFM1415 (M8340103xxxxxxJ) 12 pairs of resistors R1 R2 R2 R1 R2 The DFM1415 provides the user with a choice of 12 pairs of R1/R2 resistor values for pulse squaring and TTL dual-line terminating requirements. DFM1415 CAGE CODE: 91637 Revision: 12-Sep-13 Document Number: 31517 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DFM (Military M83401/03) www.vishay.com Vishay Dale PERFORMANCE CONDITIONS MAX. R (TYPICAL TEST LOTS) 1.5 x rated power, applied 1.5 h “ON” and 0.5 h “OFF” for 100 h ± 4 h at +25 °C ambient temperature ± 0.50 % R 5 cycles between -65 °C and +125 °C ± 0.50 % R 2.5 x rated working voltage for 5 s ± 0.25 % R (char. K) ± 0.50 % R (char. M) 45 min at full rated working voltage at -65 °C ± 0.25 % R (char. K) ± 0.50 % R (char. M) 240 h with humidity ranging from 80 % RH to 98 % RH ± 0.50 % R Leads immersed in +260 °C solder to within 1/16" of body for 10 s ± 0.25 % R Total of 18 shocks at 100 g's ± 0.25 % R Vibration 12 h at maximum of 20 g's between 10 Hz and 2000 Hz ± 0.25 % R Load life 1000 h at +70 °C, rated power applied 1.5 h “ON”, 0.5 h “OFF” for full 1000 h period ± 0.50 % R (char. K) ± 2.0 % R (char. M) Terminal strength 1.5 pound pull for 30 s ± 0.25 % R Insulation resistance 10 000 M (minimum) - No evidence of arcing or damage (200 VRMS for 1 min) - TEST Power conditioning Thermal shock Short time overload Low temperature operation Moisture resistance Resistance to soldering heat Shock Dielectric withstanding voltage Revision: 12-Sep-13 Document Number: 31517 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000