CRCA www.vishay.com Vishay Dale Thick Film Resistor/Capacitor Chip Array, Surface Mount FEATURES • Single component reduces board space and component counts • X7R dielectric characteristic • Wrap around termination • Thick film R/C element • Inner electrode protection • Flow and reflow solderable • Automatic placement capability, standard size • 8 pin or 10 pin configurations • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 STANDARD ELECTRICAL SPECIFICATIONS RESISTOR CHARACTERISTICS CAPACITOR CHARACTERISTICS POWER GLOBAL CAP. TEMPERATURE CAP. CAP. SCHEMATIC RATING TEMP. RESISTANCE RESISTANCE MODEL COEFF. TOLERANCE RANGE DIELECTRIC COEFFICIENT TOL. VOLTAGE RANGE P70 °C ± ppm/°C ±% pF % ±% VDC W CRCA12E CRCA12S 01 0.125 200 5 10 to 1M X7R ± 15 20 50 10 to 270 02 0.125 200 5 10 to 1M X7R ± 15 20 50 10 to 100 03 0.125 200 5 10 to 1M X7R ± 15 20 50 10 to 270 Notes RESISTOR • Operating temperature range: -55 °C to +125 °C • Technology: Thick film CAPACITOR • Operating temperature range: X7R -55 °C to +125 °C • Maximum dissipation factor: 2.5 % • Dielectric withstanding voltage: 125 VDC, 5 s, 50 mA charge • Ask about extended value ranges. • Packaging: According to EIA 481. • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material. TECHNICAL SPECIFICATIONS PARAMETER UNIT RESISTOR Rated dissipation at 70 °C (CECC 40401 I EIA 575) W 0.125 X7R CAPACITOR - Capacitor voltage rating V - 50 Dielectric withstanding voltage (5 s, 50 mA charge) VDC - 125 Category temperature range °C -55 / +125 -55 / +125 Insulation resistance > 1010 GLOBAL PART NUMBER INFORMATION New Global Part Numbering: CRCA12E081472220R (preferred part numbering format) C R C A MODEL PIN COUNT CRCA12E CRCA12S 08 = 8 pin 10 = 10 pin 1 2 E SCHEMATIC 1 = 01 2 = 02 3 = 03 0 = Special 0 8 1 4 7 2 2 RESISTANCE VALUE CAPACITANCE VALUE 2 digit significant figures, followed by a multiplier 100 = 10 683 = 68 k 105 = 1 M (Tolerance = ± 5 %) 2 digit significant figures, followed by multiplier 100 = 10 pF 560 = 56 pF 271 = 270 pF (Tolerance = ± 20 %) 2 0 R PACKAGING SPECIAL E = Lead (Pb)-free, T/R (2000 pcs) (Dash number) (Up to 1 digit) Blank = Standard R = Tin/Lead, T/R (2000 pcs) Historical Part Number Example: CRCA12E0801472J220MRB8 (will continue to be accepted) CRCA12E 08 01 472 J 220 M RB8 MODEL PIN COUNT SCHEMATIC RESISTANCE VALUE TOLERANCE CAPACITANCE VALUE TOLERANCE PACKAGING Note • For additional information on packaging, refer to the Surface Mount Network Packaging document (www.vishay.com/doc?31540). Revision: 10-Sep-15 Document Number: 31044 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRCA www.vishay.com Vishay Dale DIMENSIONS 8-Terminal device S-Version a GLOBAL MODEL CRCA12E CRCA12S CRCA12E CRCA12S PIN NO# 8 8 10 10 E-Version e SIZE INCH METRIC 2012 5032 2012 5032 2512 6432 2512 6432 L 5.1 ± 0.15 5.1 ± 0.15 6.4 ± 0.15 6.4 ± 0.15 c 2.2 2.2 WAVE SOLDERING REFLOW SOLDERING W 3.05 ± 0.15 3.05 ± 0.15 3.05 ± 0.15 3.05 ± 0.15 T 0.61 ± 0.10 0.61 ± 0.10 0.61 ± 0.10 0.61 ± 0.10 DIMENSIONS in millimeters B B* A A* DNOM 0.51 ± 0.25 0.38 ± 0.2 0.79 ± 0.15 0.25 0.51 ± 0.25 0.38 ± 0.2 0.79 ± 0.15 0.89 ± 0.15 0.25 0.51 ± 0.25 0.38 ± 0.2 0.79 ± 0.15 0.25 0.51 ± 0.25 0.38 ± 0.2 0.79 ± 0.15 0.89 ± 0.15 0.25 SOLDER PAD DIMENSIONS in millimeters w d p 4.3 0.57 1.27 3.9 0.57 1.27 a 0.71 0.71 b 1.05 0.86 PNOM 1.27 1.27 1.27 1.27 e 1.09 1.09 Note • The images shown are for an 8 pin part. For a 10 pin part, use the same pitch and add another pair of “a” dimension pads to the inner solder pads. 01 Circuit CRCA12E and S 02 Circuit CRCA12E and S Rated Power in % SCHEMATICS 03 Circuit CRCA12E and S 120 100 80 60 40 20 10 Pin only 10 Pin only 8 Pin 10 Pin 0 - 55 - 25 0 Derating 25 50 75 100 125 150 175 70 Ambient Temperature in °C PERFORMANCE TEST Endurance test at 70 °C MIL-STD-202 method 108 Dielectric withstanding voltage MIL-STD-202 method 301 CONDITIONS OF TEST 1000 h at 70 °C, 1.5 h “ON”, 0.5 h “OFF” 125 VDC, 5 s, 50 mA charge TEST RESULTS (TYPICAL TEST LOTS) R C ± (5 % + 2 ) ± 20 % No physical damage 100 cycles, -55 °C to +125 °C ± (5 % + 2 ) ± 20 % Moisture MIL-STD-202 method 106 Omit steps 7A and B ± (5 % + 2 ) ± 20 % Thermal shock MIL-STD-202 method 107 Resistance to soldering heat EIA 575 10 s at 260 °C solder bath temperature ± (5 % + 2 ) ± 20 % High temperature exposure EIA 575 125 °C for 100 h ± (5 % + 2 ) ± 20 % Low temperature operation EIA 575 1 h at -55 °C then 45 min at 50 V ± (5 % + 2 ) ± 20 % Solderability and leaching EIA 575 3.12 Condition C 95 % coverage APPLICABLE SPECIFICATIONS • IPC standards • EIA 575 Revision: 10-Sep-15 Document Number: 31044 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000