SLR www.vishay.com Vishay Electro-Films Surface Mount Thin Film Single Layer Resistor Array FEATURES • Standard chip sizes 0.100", 0.150", 0.210" wide • Custom chip sizes up to 0.500" x 0.500" • Custom chip sizes up to 0.500" x 0.500" • Case: 0510 to 2010 • Mixed values to 500 k • Multiple reference resistor groups • Ratio tolerance to ± 0.05 % • Ratio TCR’s to ± 1 ppm/°C • Nichrome resistor material standard. Tantalum nitride available, consult factory Product may not be to scale • Custom pad spacing 0.025" or greater SLR (single layer resistor carrier) networks are offered to provide the user with a leadless device that maximizes board density while maintaining tight ratio tolerances and TCR tracking. Pads are provided top and bottom connected by edge castellations for ease of visual solder joint inspection. Resistors can be covered with Vishay Electro-Films (EFI) proprietary thermal set plastic for physical protection or left uncoated to facilitate user trimming. SLR’s are provided with 0.050" standard contact spacing; however, 0.025" contact spacing is also available. The standard contact metallization is gold flash over nickel plate. Solder coated contacts can be provided if preferred. Custom configurations, values, and tolerance combinations are available with fast turnaround. TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES PARAMETER VALUE UNIT Total Resistance Range 10 to 500K Standard Tolerance ± 0.1 to ± 1 % ± 50; available to ± 10 ppm/°C VALUE UNIT ± 0.1 to ± 1 % TCR STANDARD ELECTRICAL SPECIFICATIONS PARAMETER Absolute Resistance Tolerance Resistance Ratio Tolerance Ratio TCR ± 0.05 to ± 0.1 % ± 5 available to ± 1 ppm/°C Absolute Resistor Stability (Mean) 300 per 1000 h at 125 °C typ. ppm Ratio Resistor Stability (Mean) 18 per 1000 h at 125 °C typ. ppm Temperature Range 0 to + 70, - 40 to + 85, - 55 to + 125 °C DC Power Rating at 70 °C 0.1 W DC Power Rating at 125 °C 0.05 W The SLR construction allows for a wide selection of special sizes and shapes with rapid turnaround and low NRE costs. The holes for the edge castellations are laser drilled into a multiple-up, large area substrates in-house prior to metallization. This permits new configurations with only laser software and a mask set. Custom parts can be provided with combinations of features listed: 1. Any combination of resistor values between 100 and 100 k in the standard sizes. 2. Custom resistor network patterns (no crossovers). 3. A wide variety of rectangular sizes and shapes with contact pads on two to four sides. 4. Pad center-to-center spacings from 0.025" (0.635 mm) and larger. 5. Uncoated to permit customer trimming. Revision: 26-Jul-12 Document Number: 61068 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SLR www.vishay.com Vishay Electro-Films OUTLINE DRAWING C B D Resistor Area E A F R1 Single Layer 16 Pin Chip Carrier Chip measures 0.300" x 0.300". Castellations are on 0.050" (1.27 mm) centers. (Special Order) PIN 1 DIMENSIONS in inches [millimeters] CENTERS A B C D E F 0.025 [0.64] (1) 0.100 [2.54] 0.015 [0.38] 0.025 [0.64] 0.015 [0.38] 0.020 [0.51] 0.050 [1.28] (2) 0.100 [2.54] 0.030 [0.76] 0.050 [1.28] 0.015 [0.38] 0.020 [0.51] 0.050 [1.28] (2) 0.150 [3.84] 0.030 [0.76] 0.050 [1.28] 0.025 [0.64] 0.020 [0.51] 0.050 [1.28] (2) 0.210 [5.37] 0.030 [0.76] 0.050 [1.28] 0.025 [0.64] 0.020 [0.51] Notes (1) 0.025" [0.64 mm] per resistor, 2 to 18 pads (2) 0.050" [1.28 mm] per resistor, 2 to 18 pads Standard Pitch: Castellations are on 0.050" (1.27 mm) centers (0.025" pitch special order) ORDERING INFORMATION Global Part Number: SLRC410001FFCGGWS Global Part Number Description: SLRC 4 RES 10K 1 % RT 1 % 50 ppm 2 ppm Au WS S MODEL L WIDTH (mil) C = 100 SLR Resistor N = 150 Carrier M = 210 NiCr on Alumina Revision: 26-Jul-12 R C 4 1 0 0 RES. NUMBER RESISTANCE MULTIPLIER RESISTORS CODE 2=2 3=3 4=4 7=7 8=8 First 4 digits are significant figures of resistance B = 0.01 A = 0.1 0 = 1.0 1 = 10.0 2 = 100.0 0 TOL. CODE (%) 1 RATIO TOL. (%) F F TCR (ppm/°C) B = 0.1 W = 0.01 B = ± 10 C = 0.25 V = 0.02 E = ± 25 D = 0.5 A = 0.05 C = ± 50 B = 0.1 K = ± 100 F = 1.0 G = 2.0 C = 0.25 M = ± 250 D = 0.5 J = 5.0 K = 10.0 F = 1.0 G = 2.0 C G G W S TC TRACK PACKAGING TERMINATION (ppm/°C) CODE F=±1 G=±2 H=±3 J=±5 K = ± 10 G = Au S = SnPb T= Lead (Pb)-free (e1) WS = Waffle pack 100 min., 1 mult Document Number: 61068 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000