Si515

Si 5 15
VO L TAG E - C ONTR OLLED C RYSTAL O S C I L L A T O R (VCXO)
100 k H Z T O 250 M H Z
Features







Supports any frequency from

100 kHz to 250 MHz
Low-jitter operation

Short lead times: <2 weeks

AT-cut fundamental mode crystal
ensures high reliability/low aging 
High power supply noise rejection 
1% control voltage linearity
Available CMOS, LVPECL, LVDS,
and HCSL outputs
Optional integrated 1:2 CMOS
fanout buffer
3.3 and 2.5 V supply options
Industry-standard 3.2 x 5.0 mm
and 5 x 7 mm package/pinouts
Pb-free/RoHS-compliant
Selectable Kv (60, 90, 120,
150 ppm/V)
SONET/SDH/OTN
PON
 Low Jitter PLLs
 xDSL
Broadcast video
Telecom
 Switches/routers
 FPGA/ASIC clock generation



Ordering Information:
See page 14.
Pin Assignments:
See page 12.
Applications

Si5602
Description
The Si515 VCXO utilizes Silicon Laboratories' advanced PLL technology to
provide any frequency from 100 kHz to 250 MHz. Unlike a traditional VCXO where
a different crystal is required for each output frequency, the Si515 uses one fixed
crystal and Silicon Labs’ proprietary synthesizer to generate any frequency across
this range. This IC-based approach allows the crystal resonator to provide
enhanced reliability, improved mechanical robustness, and excellent stability. In
addition, this solution provides superior control voltage linearity and supply noise
rejection, improving PLL stability and simplifying low jitter PLL design in noisy
environments. The Si515 is factory-configurable for a wide variety of user
specifications, including frequency, supply voltage, output format, tuning slope and
stability. Specific configurations are factory-programmed at time of shipment,
eliminating long lead times and non-recurring engineering charges associated with
custom frequency oscillators.
Vc 1
6 V DD
OE
2
5 NC
GND
3
4 CLK
CMOS VCXO
Vc 1
6
OE 2
5 CLK–
GND 3
4 CLK+
VDD
LVPECL/LVDS/HCSL/
Dual CMOS VCXO
Functional Block Diagram
V DD
Power Supply Filtering
OE
Fixed
Frequency
Oscillator
Vc
Any-Frequency
0.1 to 250 MHz
Clock Synthesis
CLK+
CLK–
ADC
GND
Rev. 1.0 6/12
Copyright © 2012 by Silicon Laboratories
Si515
Si5 15
2
Rev. 1.0
Si515
TABLE O F C ONTENTS
Section
Page
1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1. Dual CMOS Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4. Package Outline Diagram: 5 x 7 mm, 6-pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5. PCB Land Pattern: 5 x 7 mm, 6-pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
6. Package Outline Diagram: 3.2 x 5.0 mm, 6-pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7. PCB Land Pattern: 3.2 x 5.0 mm, 6-pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8. Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8.1. Si515 Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8.2. Top Marking Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Rev. 1.0
3
Si5 15
1. Electrical Specifications
Table 1. Recommended Operating Conditions
VDD = 2.5 or 3.3 V ±10%, TA = –40 to +85 oC
Parameter
Supply Voltage
Symbol
VDD
Supply Current
IDD
Test Condition
Min
Typ
Max
Unit
3.3 V option
2.97
3.3
3.63
V
2.5 V option
2.25
2.5
2.75
V
CMOS, 100 MHz,
single-ended
—
24
29
mA
LVDS
(output enabled)
—
22
26
mA
LVPECL
(output enabled)
—
42
46
mA
HCSL
(output enabled)
—
44
47
mA
Tristate
(output disabled)
—
—
22
mA
OE “1” Setting
VIH
See Note
0.80 x VDD
—
—
V
OE “0” Setting
VIL
See Note
—
—
0.20 x VDD
V
OE Internal Pull-Up/
Pull-Down Resistor*
RI
—
45
—
k
Operating Temperature
TA
–40
—
85
oC
*Note: Active high and active low polarity OE options available. Active high uses internal pull-up. Active low uses internal pulldown. See ordering information on page 13.
4
Rev. 1.0
Si515
Table 2. Vc Control Voltage Input
VDD = 2.5 or 3.3 V ±10%, TA = –40 to +85 oC
Parameter
Symbol
Control Voltage Range
VC
Control Voltage Tuning Slope
(10 to 90% VDD)
Kv
Kv Variation
Test Condition
Min
Typ
Max
Unit
0.1 x VDD
VDD/2
0.9 x VDD
V
Positive slope,
ordering option
Kv_var
BSL
60, 90, 120, 150
ppm/V
—
—
±10
%
–5
±1
+5
%
Control Voltage Linearity
LVC
Modulation Bandwidth
BW
—
10
—
kHz
Vc Input Impedance
ZVC
—
100
—
k
Table 3. Output Clock Frequency Characteristics
VDD = 2.5 or 3.3 V ±10%, TA = –40 to +85 oC
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
FO
CMOS, Dual CMOS
0.1
—
212.5
MHz
FO
LVDS/LVPECL/HCSL
0.1
—
250
MHz
Temperature Stability
ST
TA = –40 to +85 oC
–20
—
+20
ppm
Aging
A
Frequency drift over 10 year life
—
—
±8.5
ppm
Minimum Absolute Pull Range
APR
Ordering option
Startup Time
TSU
Minimum VDD to output frequency (FO) within specification
—
—
10
ms
Disable Time
TD
FO 10 MHz
—
—
5
µs
40
µs
20
µs
60
µs
Nominal Frequency
±30, ±50,±80, ±100
FO < 10 MHz
Enable Time
TE
FO  10 MHz
FO < 10 MHz
Rev. 1.0
—
—
ppm
5
Si5 15
Table 4. Output Clock Levels and Symmetry
VDD = 2.5 or 3.3 V ±10%, TA = –40 to +85 oC
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
CMOS Output Logic High
VOH
0.85 x VDD
—
—
V
CMOS Output Logic Low
VOL
—
—
0.15 x VDD
V
CMOS Output Logic High
Drive
IOH
3.3 V
–8
—
—
mA
2.5 V
–6
—
—
mA
CMOS Output Logic Low
Drive
IOL
3.3 V
8
—
—
mA
2.5 V
6
—
—
mA
0.1 to 125 MHz,
CL = 15 pF
—
0.8
1.2
ns
0.1 to 212.5 MHz,
CL = no load
—
0.6
0.9
ns
CMOS Output Rise/Fall Time
(20 to 80% VDD)
TR/TF
LVPECL/HCSL Output
Rise/Fall Time
(20 to 80% VDD)
TR/TF
—
—
565
ps
LVDS Output Rise/Fall Time
(20 to 80% VDD)
TR/TF
—
—
800
ps
VOC
50  to VDD – 2 V,
single-ended
—
VDD –
1.4 V
—
V
VO
50  to VDD – 2 V,
single-ended
0.55
0.8
0.90
VPPSE
VOC
100  line-line,
VDD = 3.3/2.5 V
1.13
1.23
1.33
V
VO
Single-ended 100 
differential termination
0.25
0.38
0.42
VPPSE
HCSL Output Common Mode
VOC
50 to ground
0.35
0.38
0.42
V
HCSL Output Swing
VO
Single-ended
0.58
0.73
0.85
VPPSE
Duty Cycle
DC
48
50
52
%
LVPECL Output Common
Mode
LVPECL Output Swing
LVDS Output Common Mode
LVDS Output Swing
6
Rev. 1.0
Si515
Table 5. Output Clock Jitter and Phase Noise (LVPECL)
VDD = 2.5 or 3.3 V ±10%, TA = –40 to +85 oC; Output Format = LVPECL
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Period Jitter (RMS)
JPRMS
10 k samples1
—
—
1.3
ps
Period Jitter (PK-PK)
JPPKPK
10 k samples1
—
—
11
ps
12 kHz to 20 MHz (brickwall)
—
0.9
1.3
ps
1.875 MHz to 20 MHz2 (brickwall)
—
0.25
0.5
ps
100 Hz offset
—
–71
—
dBc/Hz
1 kHz offset
—
–93
—
dBc/Hz
10 kHz offset
—
–113
—
dBc/Hz
100 kHz offset
—
–124
—
dBc/Hz
1 MHz offset
—
–136
—
dBc/Hz
100 kHz sinusoidal noise
—
4.0
—
ps
200 kHz sinusoidal noise
—
3.5
—
ps
500 kHz sinusoidal noise
—
3.5
—
ps
1 MHz sinusoidal noise
—
3.5
—
ps
FO = 156.25 MHz,
Offset > 10 kHz
—
–75
—
dBc
Phase Jitter (RMS)
2
φJ
Phase Noise, 155.52 MHz
φN
Additive RMS Jitter Due to
External Power Supply
Noise3
Spurious Performance
JPSRR
SPR
Notes:
1. Applies to output frequencies: 74.17582, 74.25, 75, 77.76, 100, 106.25, 125, 148.35165, 148.5, 150, 155.52, 156.25,
212.5, 250 MHz.
2. Applies to output frequencies: 100, 106.25, 125, 148.35165, 148.5, 150, 155.52, 156.25, 212.5, 250 MHz.
3. 156.25 MHz. Increase in jitter on output clock due to spurs introduced by sinewave noise added to VDD (100 mVPP).
Rev. 1.0
7
Si5 15
Table 6. Output Clock Jitter and Phase Noise (LVDS)
VDD = 1.8 V ±5%, 2.5 or 3.3 V ±10%, TA = –40 to +85 oC; Output Format = LVDS
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Period Jitter
(RMS)
JPRMS
10k samples1
—
—
2.1
ps
Period Jitter
(Pk-Pk)
JPPKPK
10k samples1
—
—
18
ps
Phase Jitter
(RMS)
φJ
1.875 MHz to 20 MHz integration
bandwidth2 (brickwall)
—
0.25
0.55
ps
12 kHz to 20 MHz integration bandwidth2 (brickwall)
—
0.8
1.1
ps
100 Hz
—
–72
—
dBc/Hz
1 kHz
—
–93
—
dBc/Hz
10 kHz
—
–114
—
dBc/Hz
100 kHz
—
–123
—
dBc/Hz
1 MHz
—
–136
—
dBc/Hz
LVPECL output, 156.25 MHz,
offset>10 kHz
—
–75
—
dBc
Phase Noise,
156.25 MHz
Spurious
φN
SPR
Notes:
1. Applies to output frequencies: 74.17582, 74.25, 75, 77.76, 100, 106.25, 125, 148.35165, 148.5, 150, 155.52, 156.25,
212.5, 250 MHz.
2. Applies to output frequencies: 100, 106.25, 125, 148.35165, 148.5, 150, 155.52, 156.25, 212.5 and 250 MHz.
8
Rev. 1.0
Si515
Table 7. Output Clock Jitter and Phase Noise (HCSL)
VDD = 1.8 V ±5%, 2.5 or 3.3 V ±10%, TA = –40 to +85 oC; Output Format = HCSL
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Period Jitter
(RMS)
JPRMS
10k samples*
—
—
1.2
ps
Period Jitter
(Pk-Pk)
JPPKPK
10k samples*
—
—
11
ps
Phase Jitter
(RMS)
φJ
1.875 MHz to 20 MHz integration
bandwidth*(brickwall)
—
0.25
0.30
ps
12 kHz to 20 MHz integration bandwidth* (brickwall)
—
0.8
1.0
ps
100 Hz
—
–75
—
dBc/Hz
1 kHz
—
–98
—
dBc/Hz
10 kHz
—
–117
—
dBc/Hz
100 kHz
—
–127
—
dBc/Hz
1 MHz
—
–136
—
dBc/Hz
LVPECL output, 156.25 MHz,
offset>10 kHz
—
–75
—
dBc
Phase Noise,
156.25 MHz
Spurious
φN
SPR
*Note: Applies to an output frequency of 100 MHz.
Rev. 1.0
9
Si5 15
Table 8. Output Clock Jitter and Phase Noise (CMOS, Dual CMOS)
VDD = 1.8 V ±5%, 2.5 or 3.3 V ±10%, TA = –40 to +85 oC; Output Format = CMOS, Dual CMOS
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Phase Jitter
(RMS)
φJ
1.875 MHz to 20 MHz integration
bandwidth2 (brickwall)
—
0.25
0.35
ps
12 kHz to 20 MHz integration bandwidth2 (brickwall)
—
0.8
1.1
ps
100 Hz
—
–71
—
dBc/Hz
1 kHz
—
–93
—
dBc/Hz
10 kHz
—
–113
—
dBc/Hz
100 kHz
—
–123
—
dBc/Hz
1 MHz
—
–136
—
dBc/Hz
LVPECL output, 156.25 MHz,
offset>10 kHz
—
–75
—
dBc
Phase Noise,
156.25 MHz
Spurious
φN
SPR
Notes:
1. Applies to output frequencies: 74.17582, 74.25, 75, 77.76, 100, 106.25, 125, 148.35165, 148.5, 150, 155.52, 156.25,
212.5 MHz.
2. Applies to output frequencies: 100, 106.25, 125, 148.35165, 148.5, 150, 155.52, 156.25, 212.5 MHz.
Table 9. Environmental Compliance and Package Information
Parameter
Conditions/Test Method
Mechanical Shock
MIL-STD-883, Method 2002
Mechanical Vibration
MIL-STD-883, Method 2007
Solderability
MIL-STD-883, Method 2003
Gross and Fine Leak
MIL-STD-883, Method 1014
Resistance to Solder Heat
MIL-STD-883, Method 2036
Moisture Sensitivity Level
MSL 1
Contact Pads
10
Gold over Nickel
Rev. 1.0
Si515
Table 10. Thermal Characteristics
Parameter
Thermal Resistance Junction to Ambient
Symbol
Test Condition
Value
Unit
JA
Still air
110
°C/W
Table 11. Absolute Maximum Ratings1
Parameter
Symbol
Rating
TAMAX
85
o
C
TS
–55 to +125
o
C
VDD
–0.5 to +3.8
V
VI
–0.5 to VDD + 0.3
V
ESD Sensitivity (HBM, per JESD22-A114)
HBM
2
kV
Soldering Temperature (Pb-free profile)2
TPEAK
260
TP
20–40
Maximum Operating Temperature
Storage Temperature
Supply Voltage
Input Voltage (any input pin)
Soldering Temperature Time at TPEAK (Pb-free profile)2
Unit
o
C
sec
Notes:
1. Stresses beyond those listed in this table may cause permanent damage to the device. Functional operation or
specification compliance is not implied at these conditions. Exposure to maximum rating conditions for extended
periods may affect device reliability.
2. The device is compliant with JEDEC J-STD-020.
Rev. 1.0
11
Si5 15
2. Pin Descriptions
Vc 1
6 V DD
Vc 1
6 VDD
OE
2
5 NC
OE 2
5 CLK–
GND
3
4 CLK
GND 3
4 CLK+
LVPECL/LVDS/HCSL/
Dual CMOS VCXO
CMOS VCXO
Table 12. Si515 Pin Descriptions (CMOS)
Pin
Name
CMOS Function
1
VC
Control Voltage Input.
2
OE
Output Enable. Internal pull-up for OE active high. Pulldown for OE active low. See ordering information.
3
GND
Electrical and Case Ground.
4
CLK
Clock Output.
5
NC
No connect. Make no external connection to this pin.
6
VDD
Power Supply Voltage.
Table 13. Si515 Pin Descriptions (LVPECL/LVDS/HCSL/Dual CMOS)
12
Pin
Name
LVPECL/LVDS/HCSL/Dual CMOS Function
1
VC
Control Voltage Input.
2
OE
Output Enable. Internal pull-up for OE active high. Pulldown for OE active low. See ordering information.
3
GND
Electrical and Case Ground.
4
CLK+
Clock Output.
5
CLK–
Complementary Clock Output.
6
VDD
Power Supply Voltage.
Rev. 1.0
Si515
2.1. Dual CMOS Buffer
Dual CMOS output format ordering options support either complementary or in-phase output signals. This feature
enables replacement of multiple VCXOs with a single Si515 device.
~
Complementary
Outputs
~
In-Phase
Outputs
Figure 1. Integrated 1:2 CMOS Buffer Supports Complementary or In-Phase Outputs
Rev. 1.0
13
Si5 15
3. Ordering Information
The Si515 supports a variety of options including frequency, stability, tuning slope, output format, and VDD. Specific
device configurations are programmed into the Si515 at time of shipment. Configurations are specified using the
Part Number Configuration chart shown below. Silicon Labs provides a web browser-based part number
configuration utility to simplify this process. Refer to www.silabs.com/VCXOPartNumber to access this tool. The
Si515 VCXO series is supplied in industry-standard, RoHS compliant, lead-free, 3.2 x 5.0 mm and 5 x 7 mm
packages. Tape and reel packaging is an ordering option.
Series
Output Format
Package
515
Single Frequency VCXO
LVPECL, LVDS, HCSL,
CMOS, Dual CMOS
6-pin
A = Revision: A
G = Temp Range: -40°C to 85°C
R = Tape & Reel; Blank = Trays.
1st Option Code:
Output Format
VDD
Output Format
A
3.3V
LVPECL
B
3.3V
LVDS
C
3.3V
CMOS
D
3.3V
HCSL
E
2.5V
LVPECL
515 X X X XXXMXXX X AGR
F
2.5V
LVDS
G
2.5V
CMOS
H
2.5V
HCSL
M
3.3V
Dual CMOS (In-phase)
N
3.3V
Dual CMOS (Complementary)
P
2.5V
Dual CMOS (In-phase)
Q
2.5V
Dual CMOS (Complementary)
3rd Option Code:
Output Enable
Dimensions
A
OE Active High
A
B
OE Active Low
B
2nd Option Code: Stability & APR
Temp
Stability
Package Option
OE Polarity
Minimum APR
Kv
3.3 V
2.5 V
Frequency Code
Frequency
Mxxxxxx
Description
fOUT < 1 MHz
A
±20ppm
±150ppm/V
±100ppm
±80ppm
xMxxxxx
1 MHz ” fOUT < 10 MHz
B
±20ppm
±120ppm/V
±80ppm
±50ppm
xxMxxxx
M
10 MH
MHz ” fOUT < 100 MH
MHz
C
±20ppm
±90ppm/V
±50ppm
±30ppm
xxxMxxx
Not Supported
xxxxxx
D
±20ppm
±60ppm/V
±30ppm
5 x 7 mm
3.2 x 5 mm
100 MHz ” fOUT < 250 MHz
Code if frequency requires >6 digit resolution
Figure 2. Part Number Convention
Example ordering part number: 515BBB212M500BAGR.
The series prefix, 515, indicates the device is a single frequency VCXO.
The 1st option code B specifies the output format is LVDS and powered from a 3.3 V supply. The stability and APR
code B indicates a temperature stability of ±20 ppm with a tuning slope of ±120 ppm/V. The 3rd option code B
specifies the OE pin is active low.
The frequency code is 212M500. Per this convention, and as indicated by the part number lookup utility at
www.silabs.com/VCXOpartnumber, the output frequency is 212.5 MHz. The package code B refers to the
3.2 x 5 mm footprint with six pins. The last A refers to the product revision, G indicates the temperature range (–40
to +85 °C), and R specifies the device ships in tape and reel format.
Note: CMOS and Dual CMOS maximum frequency is 212.5 MHz.
14
Rev. 1.0
Si515
4. Package Outline Diagram: 5 x 7 mm, 6-pin
Figure 3 illustrates the package details for the Si515. Table 14 lists the values for the dimensions shown in the
illustration.
Figure 3. Si515 Outline Diagram
Table 14. Package Diagram Dimensions (mm)
Dimension
Min
Nom
Max
A
1.50
1.65
1.80
b
1.30
1.40
1.50
c
0.50
0.60
0.70
D
D1
5.00 BSC.
4.30
4.40
e
2.54 BSC.
E
7.00 BSC.
4.50
E1
6.10
6.20
6.30
H
0.55
0.65
0.75
L
1.17
1.27
1.37
L1
0.05
0.10
0.15
p
1.80
—
2.60
R
0.7 REF.
aaa
0.15
bbb
0.15
ccc
0.10
ddd
0.10
eee
0.05
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
Rev. 1.0
15
Si5 15
5. PCB Land Pattern: 5 x 7 mm, 6-pin
Figure 4 illustrates the 5 x 7 mm PCB land pattern for the Si515. Table 15 lists the values for the dimensions shown
in the illustration.
Figure 4. Si515 PCB Land Pattern
Table 15. PCB Land Pattern Dimensions (mm)
Dimension
(mm)
C1
4.20
E
5.08
X1
1.55
Y1
1.95
Notes:
General
All dimensions shown are in millimeters (mm) unless otherwise noted.
Dimensioning and Tolerancing is per the ANSI Y14.5M-1994 specification.
This Land Pattern Design is based on the IPC-7351 guidelines.
All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition
(LMC) is calculated based on a Fabrication Allowance of 0.05 mm.
Solder Mask Design
1.
2.
3.
4.
5. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder
mask and the metal pad is to be 60 µm minimum, all the way around the pad.
Stencil Design
6. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used
to assure good solder paste release.
7. The stencil thickness should be 0.125 mm (5 mils).
8. The ratio of stencil aperture to land pad size should be 1:1.
Card Assembly
9. A No-Clean, Type-3 solder paste is recommended.
10. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for
Small Body Components.
16
Rev. 1.0
Si515
6. Package Outline Diagram: 3.2 x 5.0 mm, 6-pin
Figure 5 illustrates the package details for the 3.2 x 5 mm Si510/511. Table 16 lists the values for the dimensions
shown in the illustration.
Figure 5. Si510/511 Outline Diagram
Table 16. Package Diagram Dimensions (mm)
Dimension
A
b
c
D
D1
e
E
E1
H
L
L1
p
R
aaa
bbb
ccc
ddd
eee
Min
1.06
0.54
0.35
2.55
4.35
0.45
0.90
0.05
1.17
Nom
1.17
0.64
0.45
3.20 BSC
2.60
1.27 BSC
5.00 BSC
4.40
0.55
1.00
0.10
1.27
0.32 REF
0.15
0.15
0.10
0.10
0.05
Max
1.28
0.74
0.55
2.65
4.45
0.65
1.10
0.15
1.37
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
Rev. 1.0
17
Si5 15
7. PCB Land Pattern: 3.2 x 5.0 mm, 6-pin
Figure 6 illustrates the recommended 3.2 x 5 mm PCB land pattern for the Si515. Table 17 lists the values for the
dimensions shown in the illustration.
Figure 6. Si515 PCB Land Pattern
Table 17. PCB Land Pattern Dimensions (mm)
Dimension
(mm)
C1
2.60
E
1.27
X1
0.80
Y1
1.70
Notes:
General
All dimensions shown are in millimeters (mm) unless otherwise noted.
Dimensioning and Tolerancing is per the ANSI Y14.5M-1994 specification.
This Land Pattern Design is based on the IPC-7351 guidelines.
All dimensions shown are at Maximum Material Condition (MMC). Least Material
Condition (LMC) is calculated based on a Fabrication Allowance of 0.05 mm.
Solder Mask Design
1.
2.
3.
4.
5. All metal pads are to be non-solder mask defined (NSMD). Clearance between the
solder mask and the metal pad is to be 60 µm minimum, all the way around the pad.
Stencil Design
6. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be
used to assure good solder paste release.
7. The stencil thickness should be 0.125 mm (5 mils).
8. The ratio of stencil aperture to land pad size should be 1:1.
Card Assembly
9. A No-Clean, Type-3 solder paste is recommended.
10. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification
for Small Body Components.
18
Rev. 1.0
Si515
8. Top Marking
Use the part number configuration utility located at: www.silabs.com/VCXOPartNumber to cross-reference the
mark code to a specific device configuration.
8.1. Si515 Top Marking
5 C CC CC
T TTT TT
Y Y WW
8.2. Top Marking Explanation
Mark Method:
Laser
Line 1 Marking:
5 = Si515
CCCCC = Mark Code
5CCCCC
Line 2 Marking:
TTTTTT = Assembly Manufacturing Code
TTTTTT
Line 3 Marking:
Pin 1 indicator.
Circle with 0.5 mm diameter;
left-justified
YY = Year.
WW = Work week.
Characters correspond to the year and
work week of package assembly.
YYWW
Rev. 1.0
19
Si5 15
DOCUMENT CHANGE LIST
Revision 0.9 to Revision 1.0

Updated Table 1 on page 4.
Updates
to supply current typical and maximum values
for CMOS, LVDS, LVPECL and HCSL.
CMOS frequency test condition corrected to 100 MHz.
Updates to OE VIH minimum and VIL maximum values.

Updated Table 3 on page 5.
Dual
CMOS nominal frequency maximum added.
time maximum values updated.
Enable time parameter added.
Disable

Updated Table 4 on page 6.
CMOS
output rise / fall time typical and maximum
values updated.
LVPECL/HCSL output rise / fall time maximum value
updated.
LVPECL output swing maximum value updated.
LVDS output common mode typical and maximum
values updated.
HCSL output swing maximum value updated.
Duty cycle minimum and maximum values tightened to
48/52%.

Updated Table 5 on page 7.
Phase
jitter test condition, typical and maximum value
updated.
Phase noise typical values updated.
Additive RMS jitter due to external power supply noise
typical values updated.
Added Tables 6, 7, 8 for LVDS, HCSL, CMOS and
Dual CMOS operations.
 Added note to Figure 2 clarifying CMOS and Dual
CMOS maximum frequency.
 Updated Figure 5 outline diagram to correct pinout.
 Updated “8. Top Marking” section and moved to
page 19.

20
Rev. 1.0
Si515
NOTES:
Rev. 1.0
21
ClockBuilder Pro
One-click access to Timing tools,
documentation, software, source
code libraries & more. Available for
Windows and iOS (CBGo only).
www.silabs.com/CBPro
Timing Portfolio
www.silabs.com/timing
SW/HW
Quality
Support and Community
www.silabs.com/CBPro
www.silabs.com/quality
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,
USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com