UPS UPS-3000-S-2U M ilitary G rade U ninterruptible P ower S upply 3000VA/ 2500W Output Power 80-265Vrms 47-65Hz or 47-800Hz AC Input Voltage Options 115Vrms or 230Vrms 50Hz, 60Hz or 400Hz AC Output Voltage Options 28 Vnom DC Input Voltage Option Dual 500W/ Single 2500W DC Output Voltage Option >10 Min. - 2U Battery Run Time Sealed Construction, Ultra low Weight, Compact Size Designed & Manufactured in USA SynQor’s Military-Grade Uninterruptible Power Supply units are designed for the extreme environmental and demanding electrical conditions of Military/Aerospace applications. SynQor’s UPS incorporates field proven high efficiency designs and rugged packaging technologies. This UPS will accept a wide range of input voltage and frequency values while delivering a well-conditioned AC output to the load. Up to three units can be combined to provide higher power, higher voltage and/or multiple output phases. The use of lithium polymer batteries permits the lowest profile and lowest weight solution in its power class. It is designed and manufactured in SynQor’s USA facilities to comply with a wide range of military standards. Options include a dual 500W or single 2500W DC output and the ability to also draw power from a military standard 28VDC input. Combine Up to 3 units for Higher Power, Voltage and/or 3-phase AC output Features • Sealed, weather-proof, shock-proof construction • Hot swappable internal battery pack (lithium polymer) • >10 minute run-time at full power • 2500W (3000VA) output power • Full power operation: -20°C to +55°C • Universal AC input: 80-265VAC; 47-65Hz • Power factor correction at AC input • Dual input (AC and optional DC) • True on-line double conversion • Cold start with no AC or DC input connections • Pure sinusoidal AC output voltage (115VAC, 60Hz) • Handles 0.0—1.0 power factor loads and non-linear loads • Up to 3 units can be combined for higher power, voltage or a 3-phase AC output • User I/O and Configuration signal ports • 2U high rack mount unit (17.00” x 22.22”) • Low weight: 65 lbs. (including battery) In-Line Manufacturing Process • AS9100 and ISO 9001 certified facility • Full component traceability Product # UPS-3000X Phone 1-888-567-9596 Options • DC input (28Vnom) for dual source • Wide-range AC input frequency: 47Hz to 800Hz • 115Vrms or 230Vrms AC output • 50Hz, 60Hz, or 400Hz output • DC1: Two auxiliary isolated DC outputs (up to 500W each) • DC2: Single auxiliary isolated DC output (up to 2500W) • Shipboard version with floating neutral wire Specification Compliance • MIL-STD-1399-300B - Interface Std for Shipboard Systems • MIL-STD-810G - Environmental Engineering Considerations • MIL-STD-461F - Electromagnetic Interference • MIL-STD-704F - Aircraft Electrical Power Characteristics • MIL-STD-1275D - Vehicle Electrical Power Characteristics Contents Technical Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mechanical Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessory Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.synqor.com Doc.# 005-0006268 Rev. C 12/17/2015 2 3 6 7 8 Page 1 UPS UPS-3000-S-2U Technical Specification INPUT CHARACTERISTICS ENVIRONMENTAL CHARACTERISTICS MIL-STD-810G Operating AC Input MTBF 50kHrs MIL-217F Ground Benign, Ta=25°C Voltage 80-265Vrms* Temperature Methods 501.5, 502.5 Frequency 47-65Hz* Operating Temperature -20°C — +55°C (Extended Option) (47-800Hz Optional) Storage Temperature -20°C — +65°C Input Power Factor >0.98 at 47-65Hz Temperature Methods 503.5 >0.97 at 400Hz Storage Temperature >0.93 at 800Hz Altitude Method 500.5 Maximum Input Current Continuous 40A (full load, 85Vrms) Operating 0 - 18,000 ft AC Input Circuit Breaker Rating 50A Non-operating 0 - 40,000 ft (* Power Derating to 80% below 90Vrms) Environmental Tests Operating DC Input (Optional) Shock/Drop Voltage 22-33V Continuous Maximum Input Current 124A (full load, 22V) Transient Maximum Input Current 150A -20°C — +65°C Method 516.6, Procedures 1,4,6 Method 514.6 Vibration CAT 5 & 24 Fungus Method 508.6 Salt Fog OUTPUT CHARACTERISTICS Method 509.5 Total Output Power Continuous 2500W (3000VA) Sand and Dust Maximum DC1 Output Power 1000W Rain Maximum DC2 Output Power 2500W EMI Method 506.5 Procedure 1 MIL-STD-461F (Note: Available AC power is reduced by power delivered to the DC output) Humidity AC Output Mechanical Vibrations of AC Output Waveform Pure Sinusoidal Shipboard Equipment Voltage 115Vrms ± 3% MECHANICAL CHARACTERISTICS 230Vrms ± 3% Standard 2U Battery Pack 60Hz ± 0.5% Chassis Size (H x W x D) 50Hz ± 0.5% Case Material 400Hz ± 0.5% Total Weight 52A (115Vrms) Connectors Frequency Peak Load Current Method 510.5, Procedures 1,2 Method 507.5 Procedure 2 Method 528 Procedure 1 3.40" (2U) x 17.00" x 22.22" Aluminum 65 lbs. (with chassis & battery) 26A (230Vrms) AC Input Connector CA02COME22-2PB Load Power Factor 0-1.0 (leading or lagging) DC Input Connector CA02COME24-10PB Total Harmonic Distortion 2% (2000W resistive load) AC Output Connector Dual DC1 Output (optional) Voltage Regulation (Over Load & Temperature) ± 3% Common Voltage/Power combinations (Two separate DC outputs) (Other Options Available) CA02COME22-2SB DC1 Output Connector CA02COME22-22SB DC2 Output Connector CA02COME24-10SB 12V at 42A =504W User I/O Ports 15V at 34A =510W 24V at 21A =504W 28V at 18A =504W 40V at 12.5A 50V at 10A =500W =500W Configuration I/O Port HD DB15 Male Cooling Exhaust Fans Sound Pressure Level (SPL) 54 dB(A) Air Flow 0.67(m3/min) 23.7 CFM Four fans in system, above specs are for each fan separately. HD DB15 Female DC2 Output (optional) Voltage Setpoint ± 3% Droop Share (Output droops vs. load to allow passive sharing among modules.) 24V Option Voltage Regulation (Over Load & Temperature) -15% 26V at 0A 22V at 100A =2200W 28V Option Voltage Regulation (Over Load & Temperature) -13% 30V at 0A 26V at 96.2A =2500W Product # UPS-3000X Phone 1-888-567-9596 www.synqor.com Doc.# 005-0006268 Rev. C 12/17/2015 Page 2 UPS UPS-3000-S-2U Technical Specification 1 5 10 6 15 High Density DB15 Female (15 Pin Connector) Signal PIN TX 2 RS232 DCE Device Transmit RX 3 RS232 DCE Device Receive GND 4, 5 11 Function Ground reference for all digital inputs and outputs LOW_BATT 6 Open collector output where “low” indicates battery charge level <10% ACIN_GOOD 7 Open collector output where “low” indicates AC Input voltage is within range +5V 8 Vout with minimal current drive usable as a pull-up voltage for open collector output signals. Load must be <35mA 9 Open collector output where “low” indicates that the UPS is running on battery power. ON_BATT REMOTE_START 12 Drive this line “high” with ≥5mA to enable UPS outputs SHUTDOWN 13 Drive this line “high” with ≥5mA to disable UPS outputs OUT_OK 14 Open collector output where “low” indicates AC Output voltage is within range OVER_TEMP 15 Open collector output where “low” indicates that the UPS is at or above its maximum temperature Safety & Qualifications IEC 62133 Safety requirements for portable secondary sealed cells. ST/SG/AC.10/11/Rev.5 UN Recommendations on the Transport of Dangerous Goods UL 1642 Lithium Batteries IEC 62040-1 General and safety requirements for UPS IEC 62040-2 UPS Electromagnetic compatibility (Category C4) LITHIUM-POLYMER BATTERY CHARACTERISTICS Standard 1U Battery Pack Run Time 1250W : 10 min 1000W : 13 min Recharge Time (to 90% charge) Standard Total Output Power < 1000W Temperature Range for Recharge: 0°C to 45°C Internal heaters maintain battery temperature above 0°C when input power is present. Battery charging only enabled below +45°C. 625W : 21 min 2 hrs UPS-3000 uses 2 1U Battery Packs Product # UPS-3000X Phone 1-888-567-9596 www.synqor.com Doc.# 005-0006268 Rev. C 12/17/2015 Page 3 UPS UPS-3000-S-2U Mechanical Features UPS-3000-S-2U Status LED Front Panel Status Indicator Panel 2U 3.40” Air Intake On/Off 17.00" Rear Panel UPS Units with DC Input / DC1 Output Options DC1 Output Option Exhaust Fans DC Input Option Ethernet Port Option AC Input Exhaust Fans AC Circuit Breaker 2U 8.6cm AC Output User I/O CONFIG Port Ground Stud (1/4-20) Rear Panel UPS Units with DC1 Output / DC2 Output Options DC1 Output Option Exhaust Fans DC2 Output Option Ethernet Port Option AC Input Exhaust Fans AC Circuit Breaker 2U 8.6cm AC Output Product # UPS-3000X User I/O Phone 1-888-567-9596 CONFIG Port www.synqor.com Ground Stud (1/4-20) Doc.# 005-0006268 Rev. C 12/17/2015 Page 4 UPS UPS-3000-S-2U Block Diagram AC INPUT AC to DC w/ PFC and ISOLATION ISOLATED INVERTER AC OUTPUT DC INPUT ELECTRONIC SWITCH ISOLATED DC-DC CONVERTER 2x DC1 OUTPUT (OPTIONAL) (Not available with DC2 Option) (OPTIONAL) ISOLATED DC-DC CONVERTER DC2 OUTPUT (OPTIONAL) BATTERY BULK ENERGY STORAGE CAPACITOR with CHARGER and ELECTRONIC SWITCH Product # UPS-3000X Phone 1-888-567-9596 www.synqor.com Doc.# 005-0006268 Rev. C 12/17/2015 Page 5 UPS UPS-3000-S-2U Mechanical Diagrams 17.00 0.750 18.700 22.22 9.750 0.750 1.50 0.75 0.313 TYP. POWER IN CHARGE LOAD CHARGE FAN BATT UPS BATT FAN 3.40 BATT ITT A B ITT-CANNON F E D C A A B G C D 22-22 C 24-10 AC OUTPUT ETHERNET PORT DC INPUT A AC INPUT 3.40 C ITT 22-22 Product # UPS-3000X B ITT 22-2 DC OUTPUT B 0.83 1.75 UPS BATT O OFF O F N F POWER IN POWER OUT LOAD O OFF O F N F POWER OUT 5 10 15 1 1 6 6 11 11 5 10 15 COMM/AUX PORT Phone 1-888-567-9596 www.synqor.com Doc.# 005-0006268 Rev. C 12/17/2015 Page 6 UPS UPS-3000-S-2U Accessory Options Replacement Battery Packs 1U; 10 lbs. (200 Watt Hours) - Two required per UPS Rail Kits Slide Rail Kit2 Fixed Bracket Kit3 Power Cables (10' long) AC Input (Hardwire) AC Output (115Vrms/230Vrms) (Hardwire) DC Input (Hardwire) DC1 Output (Hardwire) DC2 Output (Hardwire) AC Output Power Strip (Circular Connector) 6 NEMA Receptacles with Breaker (Rackmount & 3' Cable) Rackmount Transit Cases Transit Case, 3U, Gray, with Casters3 Transit Case, 3U, Gray, No Casters3 3000S Series BAT-0200-S-1U-000 SYN-9002 SYN-9033 SYN-9105 SYN-9135 SYN-9155 SYN-9173 SYN-9178 SYN-9236 SYN-9410 SYN-9412 Notes: 1: Other Options also available, check the website or contact [email protected] for further information. 2: Slide Rail Kit (SYN-9002) is not recommended for transit and ruggedized use. 3: Fixed Bracket Kit (SYN-9031) with Transit Case (SYN-9410 or SYN-9412) is required for transit and ruggedized use (qualified to pass MIL-STD-810G Loose Cargo andTransit Drop requirements). User Communication (I/O) Cables HD DB15M to DB9F (RS232, 10') HD DB15M to DB15M (RS232 and Digital I/O, 10') Mil-Circular to RJ45 (Ethernet, 10') Configuration Cables HD DB15F to DB15F (2 Units Parallel, 3') HD DB15F to DB15F (3 Units Parallel, 6') HD DB15F to DB15F (2 Units Series, 3') HD DB15F to DB15F (3 Units 3 Phase, 6') Optional Rackmount Transit Case SYN-9301 SYN-9305 SYN-9321 SYN-9311 SYN-9315 SYN-9313 SYN-9317 6 NEMA Receptacles with Breaker Product # UPS-3000X Phone 1-888-567-9596 www.synqor.com Doc.# 005-0006268 Rev. C 12/17/2015 Page 7 UPS UPS-3000-S-2U Ordering Information PART NUMBERING SYSTEM Model Number Power UPS-3000-S-2U 2500W 3000VA Family Output Power UPS 3000 Options Battery AC Input AC Output AC Output Run-Time Floating Height Weight DC Input Frequency Voltage Frequency @ Full Power DC Output Neutral (28V nom) (50/60Hz or (115Vrms or (50Hz, 60Hz (80% Power) AC Output 400Hz) 230Vrms) or 400Hz) >10 min. (>13 min.) Battery Pack Height Size S 2U 2U:3.40" • AC Input AC Output Frequency Voltage 2U 3000VA UPS 3000: S:Standard 2500W 65 lbs. L 2x 500W DC1 1x 2500W DC2 • • AC Output AC Output Neutral Set Point Wire Frequency 1 G 6 5: 50Hz L:47 - 65Hz 1: 115Vrms G:Grounded 6: 60Hz W:47-800Hz 2: 230Vrms F: Floating * 4: 400Hz • • DC Input / DC2 Output Dual DC1 Output Voltage Additional Options D 28 000 S: Not Installed D: DC Input M: DC2 Out 24VDC with Droop Share R: DC2 Out 28VDC with Droop Share 00: 12: 24: 28: 40: 50: 000: None None 0CE: CE Marking 12V E00: Ethernet / 24V SNMP 28V ECE: Ethernet / 40V SNMP & 50V CE Marking Not all combinations make valid part numbers, please contact SynQor for availability. See the Product Summary web page for more options. * Note: Order “F: Floating” option when configuring the AC output for multi-unit combinations. Example: UPS-3000-S-2U-L1G6D28-000 PATENTS SynQor holds numerous U.S. patents, one or more of which apply to most of its power converter products. Any that apply to the product(s) listed in this document are identified by markings on the product(s) or on internal components of the product(s) in accordance with U.S. patent laws. SynQor’s patents include the following: Contact SynQor for further information and to order: Phone: 978-849-0600 Toll Free: 888-567-9596 Fax: 978-849-0602 E-mail: [email protected] Web: www.synqor.com Address: 155 Swanson Road Boxborough, MA 01719 USA Product # UPS-3000X Phone 1-888-567-9596 5,999,417 6,222,742 6,545,890 6,594,159 6,731,520 6,894,468 6,896,526 6,927,987 7,050,309 7,072,190 7,085,146 7,119,524 7,269,034 7,272,021 7,272,023 7,558,083 7,564,702 7,765,687 7,787,261 8,023,290 8,149,597 8,493,751 8,644,027 9,143,042 WARRANTY SynQor offers a 1 year limited warranty. Complete warranty information is listed on our website or is available upon request from SynQor. www.synqor.com Doc.# 005-0006268 Rev. C 12/17/2015 Page 8