MQHE-28E-P

MQHE-28E-P
Passive Filter
H igH R eliability eMi F ilteR
-70V to +70V
10A
60mΩ @ 125°C
>80dB @ 500kHz
Continuous Input
Output Current
Max. DC Resistance
Differential Attenuation
F ull P oweR o PeRation : -55ºC
to
+125ºC
The MilQor® series of high-reliability EMI filters brings SynQor’s
field proven technology and manufacturing expertise to the
Military/Aerospace industry. SynQor’s innovative QorSeal®
packaging approach ensures survivability in the most hostile
environments. Compatible with the industry standard format,
these filters have high differential-mode and common-mode
-HB
-P-Y
attenuation, low DC resistance, and a stabilizing bulk
capacitor resistor.
28E
HE-
MQ
TER 60W
1
I FIL
EM n 10A
i
28V
They follow conservative component
derating guidelines and they are designed and manufactured
to comply with a wide range of military standards.
Design Process
MQHEseriesfiltersare:
• DesignedforreliabilityperNAVSO-P3641-Aguidelines
• Designedwithcomponentsderatedper:
—MIL-HDBK-1547A
—NAVSOP-3641A
Qualification Process
MQHEseriesfiltersarequalifiedto:
• MIL-STD-810F
—consistentwithRTCA/DO-160E
• SynQor’sFirstArticleQualification
—consistentwithMIL-STD-883F
• SynQor’sLong-TermStorageSurvivabilityQualification
• SynQor’son-goinglifetest
DesigneD & ManufactureD in the usa
featuring Qorseal® hi-rel asseMbly
Features
•10ampsoutputcurrent
•VerylowDCresistance
•>80dBdifferential-modeattenuationat500kHz
•>60dBcommon-modeattenuationat500kHz
•Stabilizingbulkcapacitoranddampingresistorincluded
•AllcapacitorsareX7Rmulti-layerceramic
•DesignedtomeetallMIL-STD461EMIandmostRTCA/
DO-160ESection22lightningrequirements
Specification Compliance
In-Line Manufacturing Process
• AS9100andISO9001certifiedfacility
• Fullcomponenttraceability
• Temperaturecycling
• Constantacceleration
• 24,96,160hourburn-in
• Threeleveltemperaturescreening
Product # MQHE-28E-P
Phone 1-888-567-9596
MQHEseriesfilters(withMQHLconverters)aredesignedtomeet:
• MIL-HDBK-704-8(AthroughF)
• RTCA/DO-160ESection16
• MIL-STD-1275DforVIN>16V
• DEF-STAN61-5(part6)/5forVIN>16V
• MIL-STD-461(C,D,E,F)
• RTCA/DO-160ESection22
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 1
MQHE-28E-P
Current: 10A
Technical Specification
BLOCK DIAGRAM
POSITIVE
OUTPUT
POSITIVE
INPUT
RDAMPING
PINS 1, 2, 3
PINS 4, 5, 6
PINS 10, 11, 12
PINS 7, 8, 9
CBULK
INPUT
RETURN
OUTPUT
RETURN
TYPICAL CONNECTION DIAGRAM
+VIN
+VIN
+VOUT
MilQor DC-DC
CONVERTER
MQHE EMI
FILTER
-VIN
+VOUT
IN RTN
-VOUT
+VIN
LOAD
OUT RTN
+VOUT
MilQor DC-DC
CONVERTER
IN RTN
LOAD
OUT RTN
TO OTHER
LOADS
Product # MQHE-28E-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 2
MQHE-28E-P
Current: 10A
Technical Specification
MQHE-28E-P ELECTRICAL CHARACTERISTICS
Parameter
Min. Typ. Max. Units Notes & Conditions
Specifications subject to change without notice
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Continuous
Transient (≤1 s)
Isolation Voltage (Input/Output to case)
Continuous
Transient (≤1 s)
Output Current
Operating Case Temperature
Storage Case Temperature
Lead Temperature (20 s)
ELECTRICAL CHARACTERISTICS
Input Voltage
Continuous
Transient (≤1 s, Rs* = 0 Ω)
Transient (≤100 ms, Rs* = 0 Ω)
Output Voltage (continuous)
Output Current (continuous)
DC Resistance RDC
TCASE = 25°C
TCASE = 125°C
Power Dissipation (10A output current)
TCASE = 25°C
TCASE = 125°C
Total Differential-Mode Capacitance
Total Common-Mode Capacitance
Bulk Capacitor
Damping Resistor
Noise Attenuation
INPUT VOLTAGE SPIKE SUPPRESSION
Output Voltage Deviation due to a Spike
Input Voltage Spike (Centered on Vin)
±250V, 100µs, Emax = 15mJ
±600V, 10µs, Rs* = 50Ω
ISOLATION CHARACTERISTICS
Isolation Voltage (any pin to case)
Continuous
Transient (≤ 100 µs)
Isolation Resistance (any pin to case)
Vin=28V DC ±5%, Iout= 10A unless otherwise specified
Group A
Subgroup
(See Note 3)
See Note 1
-100
-200
100
200
V
V
-500
-1000
500
1000
10
125
135
300
V
V
A
°C
°C
°C
-55
-65
HB Grade Products, See Note 4
See Note 1
-70
70
-80
80
-100
100
Vout = Vin - (Iin x Rdc)
10
V
V
V
V
A
1, 2, 3
40
60
mΩ
mΩ
1
3
4
6
W
W
µF
µF
µF
Ω
54
0.29
41
0.3
1, 2, 3
1, 2, 3
1, 2, 3
Measured across input or output pins
Measured between any pin to case
See Figure 1
See Note 2
-5
-5
5
10
ΔV
ΔV
-500
-800
100
500
800
V
V
MΩ
MIL-STD-1275B/D
RTCA/DO-160E
1
1
* Rs = Source Impedance
Product # MQHE-28E-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 3
MQHE-28E-P
Current: 10A
Technical Specification
MQHE-28E-P ELECTRICAL CHARACTERISTICS (Continued)
Parameter
Min. Typ. Max. Units Notes & Conditions
Specifications subject to change without notice
RELIABILITY CHARACTERISTICS
Calculated MTBF (MIL-STD-217F2)
GB @ Tcase = 70ºC
AIF @ Tcase = 70ºC
WEIGHT CHARACTERISTICS
Device Weight
Vin=28V DC ±5%, Iout= 10A unless otherwise specified
24.9
1.42
106 Hrs.
106 Hrs.
45
g
Group A
Subgroup
(See Note 3)
Electrical Characteristics Notes
1. While the filter will survive these input voltage limits, the filter’s output voltage will be outside the limits for an MQHL converter input voltage range.
2. Verified by qualification testing and analysis.
3. Only the ES and HB grade products are tested at three temperatures. The C grade products are tested at one temperature. Please refer to the
Construction and Environmental Stress Screening Options table for details.
4. The specified operating case temperature for ES grade products is -45°C to 100°C. The specified operating case temperature for C grade
products is 0°C to 70°C.
* Rs = Source Impedance
Product # MQHE-28E-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 4
MQHE-28E-P
Current: 10A
Technical Specification
20
10
Output Impedance Magnitute (ohms)
0
-20
Attenuation (dB)
-40
-60
-80
-100
-120
-140
Differential Mode
Common Mode
-160
10
100
Frequency (kHz)
1000
0.1
0.01
0.001
0.01
-180
1
1
10000
0.1
1
10
Frequency (kHz)
100
1000
Figure 1: Simulation of calculated common-mode and differential-mode current
attenuation. The curves plot the ratio of noise current in a 50Ω LISN sensing port
connected to the noise output side of the filter to the noise current on the input side.
The filter case is also connected to chassis ground. Refer to Figures A and B.
Figure 2: Typical Output Impedance (magnitude) of the filter looking
back into its output pins with the input pins connected to a source
with zero source impedance.
Figure 3: MIL-STD-461E Method CE101 Low Frequency Conducted
Emissions of the MQHE-28-P filter with a MQHL-28-05S at 50W
output. Limit line (in red) is the ‘Submarine Applications DC Curve’.
Figure 4: MIL-STD-461E Method CE102 High Frequency
Conducted Emissions of the MQHE-28-P filter with a MQHL-28-05S
at 50W output. Limit line (in red) is the ‘Basic Curve’.
Figure 5: MIL-STD-461E Method RE101 Low Frequency Radiated
Emissions of the MQHE-28-P filter with a MQHL-28-05S at 50W
output. Limit line (in red) is the ‘Standard Curve’ from MIL-STD461C Method RE01, which is more strict than all RE101 limits.
Figure 6: MIL-STD-461E Method RE102 High Frequency Radiated
Emissions of the MQHE-28-P filter with a MQHL-28-05S at 50W
output. Limit line (in red) is the ‘Submarine External to Pressure
Hull Curve’.
Product # MQHE-28E-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 5
MQHE-28E-P
Current: 10A
Technical Specification
BASIC OPERATION AND FEATURES
The MQHE is a multi-stage differential-mode and commonmode passive EMI filter designed to interface a power source
with one or more SynQor DC/DC converters (or other loads that
create EMI). Each stage of this filter is well damped to avoid
resonances and oscillations, and only X7R multi-layer ceramic
capacitors are used. Figure 1 shows the typical differential and
common-mode attenuation provided by this filter when the
source impedance is 50Ω to chassis ground on each input line.
The MQHE EMI filter includes a large bulk capacitor (also X7R)
with a series damping resistor to correct for the unstabilizing
effect of a converter’s negative input resistance. A white paper
discussing this negative input resistance and the need for
corrective damping can be found on the SynQor website (see
Input System Instability application note). Figure 2 shows the
magnitude of the filter’s output impedance when the filter input
is connected to a stiff voltage source.
The input voltage surge and spike compliance matrix displays
the worst case requirements listed in various 28V Military
(Vehicle and Aircraft) and Civil Aircraft standards. The MQHE
EMI filter is designed to handle all of the short duration voltage
spike requirements of these standards (with certain assumptions
regarding DEF-STAN 61-5). Some of the long duration voltage
surge requirements remain within the 50V maximum transient
rating of a SynQor MQHL-28 DC/DC converter.
L I SN
Source
50Ω
I meas
V in(+)
When used with SynQor’s DC/DC converters, the MQHE EMI
filter is designed to pass all of the relevant MIL-STD-461C/D/E/F
requirements to their most stringent limits. The MIL-STD-461
Compliance Matrix Table lists these requirements and describes
the setup used to pass them. Figures 3 - 6 show results from
selected conductive and radiated emissions tests.
The filter is also designed to pass the waveform types and
applications specified in RTCA/DO-160E Section 22 (Lightning
Induced Transient Susceptibility) to Level 4. The Section 22
Compliance Matrix Table lists these waveforms and applications
and describes the setup used to pass them.
A typical application would place the MilQor filter close to the
input of the DC/DC converter, with the cases of the filter and
the converter connected together through a ground plane. Both
cases are electrically conductive, so connection to the cases can
be made with the fasteners used to secure the device.
Do not connect the outputs of multiple MQHE filters in parallel.
Connecting filters in this manner may result in slightly unequal
currents to flow in the positive and return paths of each filter.
These unequal currents may cause the internal common-mode
chokes to saturate and thus cause degraded common-mode
rejection performance.
L I SN
V out(+)
E M I F ilter
I noise
Source
50Ω
I meas
L I SN
V out(-)
L I SN
Figure A: Differential-Mode Current Attenuation, Imeas / Inoise
Product # MQHE-28E-P
E M I F ilter
Phone 1-888-567-9596
I noise
Case
50Ω
V in(-)
V out(+)
Case
Case
50Ω
V in(+)
V in(-)
V out(-)
Figure B: Common-Mode Current Attenuation, Imeas / Inoise
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 6
MQHE-28E-P
Current: 10A
Technical Specification
MIL-STD-461 COMPLIANCE MATRIX
This table shows the MIL-STD-461 requirements/limits that have been met* by a stand-alone setup comprised of:
-
MQHE-28-P Filter
MQHL-28-05S DC/DC Converter
Resistive Load
Metal Chassis Plane
-461C
-461D/E/F
Most Stringent Limit
Listed
Requirement
CE01
CE03
CE07
Class A5 (Submarine)
Class A5 (Submarine)
Class A1 (Aircraft)
CS01
CS02
Class A5 (Submarine)
Class A5 (Submarine)
CS06
Class A1/A5 (Aircraft/Sub)
CS10
CS11
Radiated
Emissions
Radiated
Susceptibility
Conducted
Emissions
Conducted
Susceptibility
Requirement
Most Stringent
Limit Listed
CE101
CE102
Submarine
Basic Curve
CS101
Curve #2
CS106
(461F Only)
Class A5 (Submarine)
Class A5 (Submarine)
CS114
CS115
CS116
Curve #5
Basic Waveform
IMAX = 10A
RE01
RE02†
Class A5 (Submarine)
Class A5 (Submarine)
RE101
RE102†
Navy
Submarine
RS01
RS02
RS03
Class A5 (Submarine)
Class A1/A5 (Aircraft/Sub)
Class A4 (Surface Ship)
RS101
RS103
Army
Aircraft External
Met by any MQME/MQHE Filter
Met by an MQME Filter having the Transient Suppression
and Reverse Polarity Protection Features
* Susceptibility requirements/limits are deemed to have been met as long as transient deviations in the converter’s output voltage
remain within ±10% of its initial value.
† Met with metal screen shield covering the filter, converter, and resistive load.
Product # MQHE-28E-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 7
MQHE-28E-P
Current: 10A
Technical Specification
RTCA/DO-160E SECTION 22 COMPLIANCE MATRIX
(LIGHTNING INDUCED TRANSIENT SUSCEPTIBILITY)
The following table shows the RTCA/DO-160 Section 22 requirements that have been met* by a stand-alone setup comprised of:
- MQME-28-P (or –T) Filter
- MQFL-28-05S DC/DC Converter
- Resistive Load
- Metal Chassis Plane
- Unshielded Power Cable Bundle
Pin Injection
Single- and
Multiple-Stroke
Cable Induction
Single- and
Multiple-Stroke
Ground Injection
Multiple-Burst
Cable Induction
Waveform
Maximum Level Passed
3
4
4
4†
5a
4†
2
4**
3
4
4
4
5a
4
3
4
Met by any MQME/MQHE Filter
Test Conditions
Signal applied to +Vin pin. Input Return pin connected to system ground
Signal applied to unshielded power
cable bundle
Signal applied between metal ground
plane and system ground
Signal applied to unshielded power
cable bundle
Met by an MQME Filter having the Transient Suppression
and Reverse Polarity Protection Features
* Requirement is deemed to have been met as long as transient deviations in the converter’s output voltage remain within ±10% of its
initial value.
† For these waveforms at Level 3 and above, an external transient suppressor of sufficient energy rating must placed across the filter’s
input pins to keep the differential transient input voltage below +200V/-50V. Negative polarity waveforms may cause power flow to the
converter to be interrupted long enough to cause a graceful shutdown and restart of the converter. Also, the reverse voltage protection
feature of the -T filter is required to protect the converter (but not the filter) from negative polarity waveform.
** For this waveform at a Level 4 and above, external transient suppressors of sufficient energy rating must be added between the
filter’s input power pins and its case to keep the common-mode transient input voltage below +800V.
Product # MQHE-28E-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 8
MQHE-28E-P
Current: 10A
Technical Specification
VOLTAGE SURGE AND SPIKE COMPLIANCE MATRIX
These tables show the Voltage Surge and Spike requirements/limits that have been met* by a stand-alone setup comprised of:
-
MQME-28-P (or –T) Filter
MQFL-28-05S DC/DC Converter
120W Resistive Load
Metal Chassis Plane
Vehicle 28Vin
Worst Case Over-Voltage Surge
Part
(Voltage/Duration)
(Gen. + Bat.)
MIL-STD-1275D
40V / 50ms
(Bat. only)
100V / 50ms
(Gen. only)
100V / 50ms
+70V to -40V / 5ms §
(Bat. Only)
(Bat. Only, Non-Regen. Ld. Sw.)
(Gen. only)
DIT08.B, DIT07.B
80V / 80ms §
MIL-HDBK-704-8
40V / 50ms
80V / 80ms §
100V / 50ms
+110V to -50V / 5ms §
+280V to -220V max §
+130V to -70V / 10µs §
+174V / 350ms
±200V / 200ns / 50Ω
DET03.A
40V / 50ms §
DET04.A
+70V to -40V / 1ms §
DIT04.A
+110V / 300ms §
Aircraft 28Vin
Part
(Voltage/Duration)
Short Duration Spikes
(Voltage/Duration/Impedance)
80V / 50ms
(704A)
60V / 550ms
N/A
50V / 50ms
47V / 100ms
(Cat A)
±600V / 10µs / 50Ω
38V / 1s
60V / 100ms
(Cat B)
±200V / 10µs / 50Ω
40V / 1s
80V / 100ms
(Cat C)
Met by any Hi-Rel Filter
+90V to -60V / 10µs §
Worst Case Over-Voltage Surge
(704B, C, D, E, F)
RTCA/DO-160E
+130V to -100V max §
+90V to -60V / 10µs §
+70V to -40V / 5ms §
(Bat. Only, Regen. Ld. Sw.)
DEF STAN 61-5 (PART 6)/6†
±250V / 15mJ / 0.5Ω
40V / 50ms
(Gen. + Bat.)
DEF STAN 61-5 (PART 6)/5†
Short Duration Spikes
(Voltage/Duration/Impedance)
N/A
48V / 1s
Met by an MQME-28-T Filter having the Transient Suppression
and Reverse Polarity Protection Features
Met by MQME-28E-T6 Filter Only:
Performance Criteria C
* Surge/spike requirements/limits are deemed to have been met as long as transient deviations in the converter’s output voltage
remain within ±10% of its initial value.
§ These are defined as the maximum disturbances that equipment can inflict upon the power system, not as disturbances imposed
upon utilization equipment. To ensure compatablitily, however, these are within the designed stress envelope of the indicated filters &
converters.
† For the DEF STAN 61-5 specification:
1) Negative surges require reverse voltage protection circuitry to protect the converter (but not the filter) from a negative input.
This circuitry is included in the MQME-28-T but not the MQME-28-P and MQHE-28-P filters.
2) The negative surges may cause the converter to shut down unless additional holdup capacitance is included.
3) Maximum spike voltages are assumed to last <1µs
Product # MQHE-28E-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 9
MQHE-28E-P
Current: 10A
Technical Specification
CONSTRUCTION AND ENVIRONMENTAL STRESS SCREENING OPTIONS
Consistent with
MIL-STD-883F
Screening
(
C-Grade
specified from
0 °C to +70 °C
Element Evaluation
Internal Visual
IPC-A-610 Class 3
No
Yes
Temperature Cycle
Method 1010
No
) (
ES-Grade
specified from
-45 °C to +100 °C
) (
)
No
500 g
Burn-in
Method 2001
(Y1 Direction)
Method 1015
24 Hrs @ +125 °C
96 Hrs @ +125 °C
Yes
Yes
Condition C
(-65 °C to +150 °C)
Condition A
(5000 g)
160 Hrs @ +125 °C
Final Electrical Test
Method 5005 (Group A)
+25 °C
-45, +25, +100 °C
-55, +25, +125 °C
Full QorSeal
Full QorSeal
Yes
QorSeal
Yes
QorSeal
Constant Acceleration
Mechanical Seal,
Thermal, and
Coating Process
External Visual
Construction Process
Method 2009
Yes
Yes
Yes
Condition B
(-55 °C to +125 °C)
HB-Grade
specified from
-55 °C to +125 °C
MilQor® Hi-Rel converters and filters are offered in three variations of environmental stress screening options. All ES-Grade and HB-Grade MilQor
Hi-Rel converters use SynQor’s proprietary QorSeal® Hi-Rel assembly process that includes a Parylene-C coating of the circuit, a high performance
thermal compound filler, and a nickel barrier gold plated aluminum case. Each successively higher grade has more stringent mechanical and
electrical testing, as well as a longer burn-in cycle. The ES- and HB-Grades are also constructed of components that have been procured through an
element evaluation process that pre-qualifies each new batch of devices.
Product # MQHE-28E-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 10
MQHE-28E-P
Current: 10A
Technical Specification
MIL-STD-810F Test
MIL-STD-810F Qualification Testing
Method
Description
Fungus
508.5
500.4 - Procedure I
Altitude
500.4 - Procedure II
Rapid Decompression 500.4 - Procedure III
Acceleration
513.5 - Procedure II
Salt Fog
509.4
501.4 - Procedure I
High Temperature
501.4 - Procedure II
502.4 - Procedure I
Low Temperature
502.4 - Procedure II
Temperature Shock
503.4 - Procedure I - C
Rain
506.4 - Procedure I
Immersion
512.4 - Procedure I
Humidity
507.4 - Procedure II
Random Vibration
514.5 - Procedure I
516.5 - Procedure I
516.5 - Procedure VI
Shock
Sinusoidal vibration
514.5 - Category 14
Sand and Dust
510.4 - Procedure I
510.4 - Procedure II
Product # MQHE-28E-P
Phone 1-888-567-9596
Table 508.5-I
Storage: 70,000 ft / 2 hr duration
Operating: 70,000 ft / 2 hr duration; Ambient Temperature
Storage: 8,000 ft to 40,000 ft
Operating: 15 g
Storage
Storage: 135 °C / 3 hrs
Operating: 100 °C / 3 hrs
Storage: -65 °C / 4 hrs
Operating: -55 °C / 3 hrs
Storage: -65 °C to 135 °C; 12 cycles
Wind Blown Rain
Non-Operating
Aggravated cycle @ 95% RH (Figure 507.5-7 aggravated temp humidity cycle, 15 cycles)
10 - 2000 Hz, PSD level of 1.5 g2/Hz (54.6 grms), duration = 1 hr/axis
20 g peak, 11 ms, Functional Shock (Operating no load) (saw tooth)
Bench Handling Shock
Rotary wing aircraft - helicopter, 4 hrs/axis, 20 g (sine sweep from
10 - 500 Hz)
Blowing Dust
Blowing Sand
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 11
MQHE-28E-P
Current: 10A
Technical Specification
First Article Testing consistent with MIL-STD-883F
MIL-STD-883F Test
Electrical Tests
Physical Dimensions test
Resistance to Solvents test
Solderability test
Lead Integrity test
Salt Atmosphere test
Adhesion of Lead Finish test
Altitude Operation test
ESD Sensitivity
Stabilization Bake test
Vibration Fatigue test
Random Vibration test
Sequential Test Group #1
Life Test – Steady State test
Life Test – Intermittent Duty test
Sequential Test Group #2
Temperature Cycle test
Constant Acceleration test
Sequential Test Group #3
Thermal Shock test
Temperature Cycle test
Moisture Resistance test
Sequential Test Group #4
Mechanical Shock test
Variable Frequency Vibration test
Product # MQHE-28E-P
Phone 1-888-567-9596
Method
5005
2016
2015.13
2003.8
2004.5
1009.8
2025.4
1001
3015.7
1008.2
2005.2
2026
Description
Condition “A”
Condition “C”
Class 2
Condition “C”
Condition “A”
Condition “II K”
1005.8
1006
1010.8
2001.2
Condition “C”
Condition “A”
1011.9
1010.8
1004.7
Condition “B”
Condition “C”
With Sub cycle
2002.4
2007.3
Condition “B”
Condition “A”
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 12
MQHE-28E-P
Current: 10A
Technical Specification
PIN DESIGNATIONS
Pin # Function
1
2
3
4
5
6
7
8
9
10
11
12
Case U
Positive input
Positive input
Positive input
Input return
Input return
Input return
Output return
Output return
Output return
Positive output
Positive output
Positive output
NOTES
1)
Case: Aluminum with gold over
nickel plate finish for the C-,
ES-, and HB-Grade products.
2)
Pins:
3)
Diameter: 0.040’’ (1.02mm)
Material: Copper
Finish: Gold over Nickel plate,
followed by Sn/Pb dip
All dimensions in inches (mm)
4)
Tolerances:
5)
Weight: 1.6 oz (45.4 g) typical
6)
Workmanship: Meets or exceeds
IPC-A-610C Class III
7)
Pin 1 identification hole, not intended
for mounting
a) x.xx +/-0.02 in.
(x.x +/-0.5mm)
b) x.xxx +/-0.010 in.
(x.xx +/-0.25mm)
Case W
Product # MQHE-28E-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 13
MQHE-28E-P
Current: 10A
Technical Specification
PIN DESIGNATIONS
Pin # Function
1
2
3
4
5
6
7
8
9
10
11
12
Case X
Positive input
Positive input
Positive input
Input return
Input return
Input return
Output return
Output return
Output return
Positive output
Positive output
Positive output
NOTES
1)
Case: Aluminum with gold over
nickel plate finish for the C-,
ES-, and HB-Grade products.
2)
Pins:
3)
4)
Diameter: 0.040’’ (1.02mm)
Material: Copper
Finish: Gold over Nickel plate,
followed by Sn/Pb dip
All dimensions in inches (mm)
Tolerances: a) x.xx +/-0.02 in.
(x.x +/-0.5mm)
b) x.xxx +/-0.010 in.
(x.xx +/-0.25mm)
5)
Weight: 1.6 oz (45.4 g) typical
6)
Workmanship: Meets or exceeds
IPC-A-610C Class III
Pin 1 identification hole, not intended
for mounting
7)
Case Y
Product # MQHE-28E-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 14
MQHE-28E-P
Current: 10A
Technical Specification
PIN DESIGNATIONS
Pin # Function
1
2
3
4
5
6
7
8
9
10
11
12
Case Z
Positive input
Positive input
Positive input
Input return
Input return
Input return
Output return
Output return
Output return
Positive output
Positive output
Positive output
NOTES
1)
Case: Aluminum with gold over
nickel plate finish for the C-,
ES-, and HB-Grade products.
2)
Pins:
3)
4)
5)
Weight: 1.6 oz (45.4 g) typical
6)
Workmanship: Meets or exceeds
IPC-A-610C Class III
Pin 1 identification hole, not intended
for mounting
7)
Product # MQHE-28E-P
Phone 1-888-567-9596
www.synqor.com
Diameter: 0.040’’ (1.02mm)
Material: Copper
Finish: Gold over Nickel plate,
followed by Sn/Pb dip
All dimensions in inches (mm)
Tolerances: a) x.xx +/-0.02 in.
(x.x +/-0.5mm)
b) x.xxx +/-0.010 in.
(x.xx +/-0.25mm)
Doc.# 005-0005151 Rev. G
05/27/16
Page 15
MQHE-28E-P
Current: 10A
Technical Specification
MilQor Filter FAMILY MATRIX
The tables below show the array of MilQor filters available. When ordering SynQor converters, please ensure that you use
the complete part number according to the table in the last page. Contact the factory for other requirements.
Features Available
Product Family Continuous
Designator
Input Voltage
MQME-28
40V
MQME-28E
70V
MQHE-28
40V
MQHE-28E
70V
MQHE-270
Power
(Amperage)
Rating
Version
(see table
below)
Enable PassThrough
Circuitry
Transient
Suppression
Circuitry
Soft-Start
Circuitry
Reverse
Polarity
Protection
Circuitry
•
•
•
•
•
•
•
•
P
320W (20A)
T
T6
160W (10A)
P
400V
160W (1A)
P
MQME-270
400V
320W (2A)
MQME-270L
400V
200W (3A)
Product # MQHE-28E-P
(In Addition to Passive Filter Components)
Phone 1-888-567-9596
P
•
R
P
•
R
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 16
MQHE-28E-P
Current: 10A
Technical Specification
PART NUMBERING SYSTEM
The part numbering system for SynQor’s MilQor DC-DC converters follows the format shown in the table below.
Model Name
Input Voltage Range
Version
28
28E
P
T
T6
270
270L
P
R
MQME
MQHE
Package Outline/Pin
Configuration
Screening
Grade
U
X
Y
W
Z
C
ES
HB
Not all combinations make valid part numbers, please contact SynQor for availability. See the Product Summary web page for more options.
Example:
MQHE-28E-P-Y-ES
APPLICATION NOTES
A variety of application notes and technical white papers can be downloaded in pdf format from the SynQor website.
Contact SynQor for further information and to order:
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
Product # MQHE-28E-P
978-849-0600
888-567-9596
978-849-0602
[email protected]
www.synqor.com
155 Swanson Road
Boxborough, MA 01719
USA
Phone 1-888-567-9596
PATENTS
SynQor holds numerous U.S. patents, one or more of which apply to most of its power conversion
products. Any that apply to the product(s) listed in this document are identified by markings on
the product(s) or on internal components of the product(s) in accordance with U.S. patent laws.
SynQor’s patents include the following:
5,999,417
6,222,742
6,545,890
6,594,159
6,894,468
6,896,526
6,927,987
7,050,309
7,072,190
7,085,146
7,119,524
7,269,034
7,272,021
7,272,023
7,558,083
7,564,702
7,765,687
7,787,261
8,023,290
8,149,597
8,493,751
8,644,027
9,143,042
WARRANTY
SynQor offers a two (2) year limited warranty. Complete warranty information
is listed on our website or is available upon request from SynQor.
www.synqor.com
Doc.# 005-0005151 Rev. G
05/27/16
Page 17