ZXCT1032

ZXCT1032
High-side inrush controller and electronic fuse
Description
The ZXCT1032 is a high-side current monitor
that drives a PMOS or PNP transistor to
provide in-rush current limit and over-current
protection. The ZXCT1032 includes a high
accuracy high-side current monitor, a start-up
timer and a re-try inhibit timer.
The ZXCT1032 takes the voltage developed
across a current shunt resistor and compares
this with an externally set trip point. It works
in three modes:
•
Linear soft-start
•
Over-current detector
•
Over-current disconnect/fuse
Linear soft-start
Upon power up the ZXCT1032 enters a linear
soft-start mode. During which the output
current ramps up from zero to a maximum
user defined trip point. The trip point is set by
the voltage on ISET pin and RSENSE.
The ramp rate is determined by capacitor CT.
The soft start ensures that capacitive loads are
smoothly charged without causing excessive
power supply startup transients.
Over-current detectior
When external capacitor CT has charged up
above the VISET the ZXCT1032 switches from its
soft-start mode to its over-current detection
mode. During this mode the external MOSFET
will be fully enhanced reducing the its voltage
drop and power dissipation.
While in this mode the internal current monitor
continually checks the output current and
compares it to the trip-current level determined
by VISET.
Over-current disconnect/fuse
If the trip current limit is exceeded at any time the
ZXCT1032 enters its Over-current disconnect
mode. The drive pin is driven high, turning the
pass MOSFET off; the flag output goes low
indicating a fault.
The drive and flag outputs are latched in these
states for a period determined by CT, VISET and the
internally set discharge current (3µA typical). After
CT has discharged to 80mV the ZXCT1032 will
restart into its linear soft-start mode.
The CT charge and discharge times have been
ratioed to so that the power dissipation in the
pass MOSFET should allow indefinite operation
in the event of a continuous load failure.
Pin 3 description:
Determines the load current trip level or
constant current level. ISET can be left open
circuit (internal 2.1V reference) or driven via a
DC voltage or µC PWM output. Its source
impedance is 50k⍀.
Features
Applications
•
•
•
Electronic fuse
•
Short circuit protected supply feed
•
Hot swap
•
Power over twisted pair
•
•
•
•
•
Accurate high-side current sensing
User defined and dynamically adjustable
trip current
Load switch control
Fault flag logic output
User defined ramp and inhibit timers
SO8 package
Temperature range -40 to 85°C
Ordering information
Order code
ZXCT1032N8TA
Pack
SO8
Issue 4 - June 2007
© Zetex Semiconductors plc 2007
Part mark
1032
Reel size
7”
1
Tape width
12mm
Quantity per reel
500
www.zetex.com
ZXCT1032
Typical application circuit
Pinout connections
SO8
VIN
R SENSE
6
8
IN+
3
ISET
INDrive 5
ZXCT
1032
Load
GND-
1
8
IN+
CT
2
7
N/C
ISET
3
6
IN-
Flag
4
5
Drive
Top view
GND
CT
1
2
Flag
4
CT
µC
GND
Pin description
Pin
Name
Description
1
GND
Ground reference for ISET and Flag pins. Most negative terminal of the
device. No other pin should go below this voltage.
2
CT
An external capacitor is connected to this pin and is used to determine
the period for constant-current mode and the timeout before restarting.
To reduce excessive heating during the soft start mode capacitors less
than 220nF are reocmmended.
3
ISET
Determines the load current trip level or constant current level. This can
be driven via a DC voltage or via a µC PWM output.
VSENSE = (VISET-150mV)/10
An input <100mV will disable the high-side switch (i.e. set IOUT = 0)
If left open-circuit, an accurate internal DC reference of 2.1V and source
impedance of 50k⍀ is used to set the voltage on this pin. (External
drivers must take this reference into account.)
4
Flag
This is an active low open collector output that goes low whenever the
current limit set by the choice of RSENSE and ISET is reached or in the
event of a shorted load.
5
Drive
This is the output drive pin to the external high side referred switch on
the ZXCT1032, capable of driving PMOS and PNP transistors.
6
IN-
The load referred input to the current monitor control loop.
7
N/C
Not connected
8
IN+
Acts as both the supply pin to the ZXCT1032 and the supply referred
sense input to the current monitor control loop.
Issue 4 - June 2007
© Zetex Semiconductors plc 2007
2
www.zetex.com
ZXCT1032
Absolute maximum ratings
VIN+ max(a) ...................................................................................................... 28 V
Voltage on any pin relative to GND ............................................................. -0.6V and VIN +0.5 V
Maximum differential voltage between VIN+ and VIN- (VSENSE) ................ 500 mV
Junction temperature range ........................................................................ -40 to 150°C
Storage temperature range .......................................................................... -55 to 150°C
Operation above the absolute maximum rating may cause device failure. Operation at the
absolute maximum ratings, for extended periods, may reduce device reliability.
NOTES:
(a) Up to a maximum of 24 hours
Recommended operating conditions
Symbol
VIN+
Parameter
Supply range
Min.
9.5
Max.
21
Units
V
TA
Ambient temperature range
-40
85
°C
VFLAG
Flag voltage range
0
VIN+
V
VISET
Voltage on ISET pin
1
2.5
V
Electrical characteristics
Test conditions Tamb = 25°C, VIN+ = 20V. Unless otherwise stated.
Symbol Parameter
IQ
Quiescent current
Conditions
Flag trip threshold
voltage
VISET =1.1V
VISET =2.1V
185
195
205
VISET
ISET open voltage
IISET = 0
2.0
2.1
2.2
V
IISET
ISET output current
VISET =0V
30
45
60
␮A
VISET = 2.1V, VSENSE > 205mV,
IDRIVE = 0,
VIN– 0.4
VIN– 0.2
VDRIVEL Drive low output voltage VISET = 2.1V, VSENSE < 185mV,
IDRIVE = 0,
VIN-7
VIN- 5.5
VSTRIP
(*)
VDRIVEH Drive high output
voltage
VSENSE1 =
Min.
0V, V_ISET = 2.1V
Typ.
1.6
Max. Units
2.5
mA
95
RDRIVEL Drive low output resistance VISET = 2.1V, VSENSE < 185mV
VFLAGL Flag Low output Voltage VISET = 2.1V, VSENSE > 205mV
IFLAG = 100µA
V
VIN- 4
9
IFLAGZ Flag open circuit leakage VISET = 2.1V, VSENSE < 185mV,
current
VFLAG = 5V
IININ- bias current
VISET = 0V
VSTRIP-TC Temperature coefficient See footnote (†)
of trip voltage
ICT-CHG Capacitor CT charging
FLAG = Open
current
ICT-DIS Capacitor CT discharging FLAG = Low
current
mV
V
k⍀
0.2
0.4
V
1
200
nA
100
200
nA
95
ppm/°C
130
200
270
␮A
1.8
3.3
5.4
␮A
NOTES:
(*) VSENSE = VIN+ - VIN-. VSTRIP is the sense voltage at which the device trips into over-current protection.
(†) Temperature dependent measurements are extracted from characterization and simulation results.
Issue 4 - June 2007
© Zetex Semiconductors plc 2007
3
www.zetex.com
ZXCT1032
Typical characteristics
(TA = 25°C and VIN+ = 20V unless otherwise stated)
Quiescent current vs temperature
Quiescent current vs input voltage
0.90
0.80
VIN+ = 9.5 to 21V
0.60
IQ (mA)
IQ (mA)
0.79
0.30
0.00
-40
0.78
-15
10
35
Temperature (C)
60
0.77
85
9
11
13
VISET vs temperature
17
19
21
VISET vs input voltage
2.20
2.101
VIN+ = 9.5 to 21V
VISET (V)
T A = 25°C
2.15
VISET (V)
15
Input voltage
2.10
2.100
2.05
2.00
-40
-15
10
35
Temperature (°C)
60
85
2.099
9
10
11
12
13
14 15 16 17
Input voltage (V)
18
19
20
21
IIN- vs input voltage
IIN- vs temperature
40
50
VIN+=9.5V
45
VIN+=20V
T A = 25°C
35
VIN+=21V
40
30
30
IIN- (nA)
IIN- (nA)
35
25
20
25
20
15
15
10
10
5
5
0
-40
-15
10
35
60
85
Temperature (°C)
Issue 4 - June 2007
© Zetex Semiconductors plc 2007
0
9
11
13
15
17
19
21
Input voltage (V)
4
www.zetex.com
ZXCT1032
Typical characteristics
(TA = 25°C and VIN+ = 20V unless otherwise stated)
ICT-CHG vs input voltage
ICT-CHG vs temperature
-206.5
0
T A = 25°C
VIN+ = 9.5 to 21V
-25
-50
-207
-100
-150
IC-CHG (uA)
IC-CHG (uA)
-75
-175
-207.5
-125
-200
-225
-250
-40
-15
10
35
Temperature (°C)
60
-208
85
9
ICT-DIS vs temperature
13
15
17
Input voltage (V)
19
21
ICT-DIS vs input voltage
3.75
5.0
4.5
11
TA =25°C
V IN+ = 9.5 to 21V
3.74
4.0
3.73
3.0
IC-DIS (uA)
IC-DIS (uA)
3.5
2.5
3.72
2.0
1.5
1.0
3.71
0.5
0.0
-40
-15
10
35
Temperature (C)
Issue 4 - June 2007
© Zetex Semiconductors plc 2007
60
3.70
85
9
11
13
15
17
19
21
Input voltage (V)
5
www.zetex.com
ZXCT1032
Application information
ZXCT1032 block diagram and description
R SENSE
(8)
(6)
IN+
+ -
IN--
ZXCT1032
Drive (5)
+
ICT-CHG
(3) ISET
200␮A
+
-
Load
(2)
CT
CT
ICT-DIS
3.3␮A
Flag
50k⍀
+
80mV
2.1V
GND
(4)
(1)
Operation of the ZXCT1032
1 After power-up, the timing capacitor (CT) is charged up by a 200µA current source. This causes
the output amplifier's drive pin to fall in voltage, progressively turning on the PMOS transistor.
The load current is monitored by the current monitor and the amplifier control loop controls
the load current allowing it to increase gradually (soft-start mode) as the voltage on CT
increases. During the soft-start phase the load current will start to build up while there is a
large voltage across the pass MOSFET; this can lead to large power dissipation if large
capacitive loads are driven and/or large CT is used.
ZXCT1032 Start up characteristic
3
1.2
VCT
1
VISET
2
0.8
1.5
0.6
ILOAD
1
0.4
10*VSENSE
0.5
Load current - A
Voltages - V
VIN+ = 18V
R SENSE = 0.2⍀
2.5 C T = 220nF
VISET = 2.1V
Trip current = 1A
0.2
0
0
0
0.5
1
1.5
2
2.5
time - ms
Issue 4 - June 2007
© Zetex Semiconductors plc 2007
6
www.zetex.com
ZXCT1032
2 The output voltage also increases due to the load current powering up the load and charging
any capacitance. After the initial soft start (load current stabilizing) the timing capacitor
charges up to 4V and the device enters its normal mode of operation. The external MOSFET
will be now fully enhanced minimizing any serial voltage drop.
ZXCT1032 Normal Operation
20
1
VLOAD
16
0.8
14
12
ILOAD
0.6
VIN+ = 18V
RSENSE = 0.2Ω
10
CT = 220nF
VISET = 2.1V
Trip current = 1A
8
0.4
6
VCT
4
Load Current - A
Timing capacitor voltage - V
18
0.2
VISET
2
0
10*VSENSE
0
5
10
Time ms
15
20
0
The ZXCT1032 has now entered its over-current detector mode; it is effectively “transparent”
to the load until the current monitor output exceeds the trip point.
3 Fuse operation is provided by the trip comparator whose threshold voltage is set by VISET
(internally nominally 2.1V, although this threshold can easily be overdriven). As the load
current increases, so does the monitor voltage. When the current monitor output voltage
exceeds VISET, the trip comparator output goes high and sets the latch with the following
results:
a The output drive is disabled.
b The open collector Flag output goes low to indicate a fault condition.
c The 200␮A current source is turned off and CT starts to discharge slowly via a 3.3␮A current
source.
ZXCT1032 Timing in over-current condition
2.5
2.5
VISET
2
1.5
VCT
VIN+
= 18 V
RSENSE
= 0.2 ⍀
ILOAD
>1A
CT
= 220 nF
1.5
VISET
= 2.1 V
Trip current = 1 A
1
1
0.5
Load Current - A
Voltages - V
2
0.5
ILOAD
0
0
Issue 4 - June 2007
© Zetex Semiconductors plc 2007
50
Time (ms)
7
100
0
150
www.zetex.com
ZXCT1032
4 When CT has discharged to "zero" (< 80mV) the latch is reset which re-enables the output drive
and allows the device to re-enter soft-start mode.
5 In the event of an overload or short circuit, stages 3 and 4 repeat indefinitely until the fault is
removed.
In the case of a permanent fault damage to the PMOS transistor should not occur because it is
only on for a short part of the overall cycle.
6 The current monitor has an intentional output offset of +150mV. If VISET is held at 0V, the output
of the trip comparator will be permanently high and the output will be completely disabled.
Issue 4 - June 2007
© Zetex Semiconductors plc 2007
8
www.zetex.com
ZXCT1032
Package outline - SO8
DIM
Inches
Millimeters
DIM
Inches
Min.
Millimeters
Min.
Max.
Min.
Max.
Max.
A
0.053
0.069
1.35
1.75
e
A1
0.004
0.010
0.10
0.25
b
0.013
0.020
0.33
0.51
D
0.189
0.197
4.80
5.00
c
0.008
0.010
0.19
0.25
H
0.228
0.244
5.80
6.20
⍜
0°
8°
0°
8°
E
0.150
0.157
3.80
4.00
h
0.010
0.020
0.25
0.50
L
0.016
0.050
0.40
1.27
-
-
-
-
-
0.050 BSC
Min.
Max.
1.27 BSC
Note: Controlling dimensions are in inches. Approximate dimensions are provided in millimeters
Issue 4 - June 2007
© Zetex Semiconductors plc 2007
9
www.zetex.com
ZXCT1032
Definitions
Product change
Zetex Semiconductors reserves the right to alter, without notice, specifications, design, price or conditions of supply of any product or
service. Customers are solely responsible for obtaining the latest relevant information before placing orders.
Applications disclaimer
The circuits in this design/application note are offered as design ideas. It is the responsibility of the user to ensure that the circuit is fit for
the user’s application and meets with the user’s requirements. No representation or warranty is given and no liability whatsoever is
assumed by Zetex with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights
arising from such use or otherwise. Zetex does not assume any legal responsibility or will not be held legally liable (whether in contract,
tort (including negligence), breach of statutory duty, restriction or otherwise) for any damages, loss of profit, business, contract,
opportunity or consequential loss in the use of these circuit applications, under any circumstances.
Life support
Zetex products are specifically not authorized for use as critical components in life support devices or systems without the express written
approval of the Chief Executive Officer of Zetex Semiconductors plc. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body
or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labelling can be reasonably expected to result in significant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to
cause the failure of the life support device or to affect its safety or effectiveness.
Reproduction
The product specifications contained in this publication are issued to provide outline information only which (unless agreed by the
company in writing) may not be used, applied or reproduced for any purpose or form part of any order or contract or be regarded as a
representation relating to the products or services concerned.
Terms and Conditions
All products are sold subjects to Zetex’ terms and conditions of sale, and this disclaimer (save in the event of a conflict between the two
when the terms of the contract shall prevail) according to region, supplied at the time of order acknowledgement.
For the latest information on technology, delivery terms and conditions and prices, please contact your nearest Zetex sales office.
Quality of product
Zetex is an ISO 9001 and TS16949 certified semiconductor manufacturer.
To ensure quality of service and products we strongly advise the purchase of parts directly from Zetex Semiconductors or one of our
regionally authorized distributors. For a complete listing of authorized distributors please visit: www.zetex.com/salesnetwork
Zetex Semiconductors does not warrant or accept any liability whatsoever in respect of any parts purchased through unauthorized sales channels.
ESD (Electrostatic discharge)
Semiconductor devices are susceptible to damage by ESD. Suitable precautions should be taken when handling and transporting devices.
The possible damage to devices depends on the circumstances of the handling and transporting, and the nature of the device. The extent
of damage can vary from immediate functional or parametric malfunction to degradation of function or performance in use over time.
Devices suspected of being affected should be replaced.
Green compliance
Zetex Semiconductors is committed to environmental excellence in all aspects of its operations which includes meeting or exceeding
regulatory requirements with respect to the use of hazardous substances. Numerous successful programs have been implemented to
reduce the use of hazardous substances and/or emissions.
All Zetex components are compliant with the RoHS directive, and through this it is supporting its customers in their compliance with
WEEE and ELV directives.
Product status key:
“Preview”
Future device intended for production at some point. Samples may be available
“Active”
Product status recommended for new designs
“Last time buy (LTB)”
Device will be discontinued and last time buy period and delivery is in effect
“Not recommended for new designs” Device is still in production to support existing designs and production
“Obsolete”
Production has been discontinued
Datasheet status key:
“Draft version”
This term denotes a very early datasheet version and contains highly provisional information, which
may change in any manner without notice.
“Provisional version”
This term denotes a pre-release datasheet. It provides a clear indication of anticipated performance.
However, changes to the test conditions and specifications may occur, at any time and without notice.
“Issue”
This term denotes an issued datasheet containing finalized specifications. However, changes to
specifications may occur, at any time and without notice.
Zetex sales offices
Europe
Americas
Asia Pacific
Corporate Headquarters
Zetex GmbH
Kustermann-park
Balanstraße 59
D-81541 München
Germany
Telefon: (49) 89 45 49 49 0
Fax: (49) 89 45 49 49 49
[email protected]
Zetex Inc
700 Veterans Memorial Highway
Hauppauge, NY 11788
USA
Zetex (Asia Ltd)
3701-04 Metroplaza Tower 1
Hing Fong Road, Kwai Fong
Hong Kong
Zetex Semiconductors plc
Zetex Technology Park, Chadderton
Oldham, OL9 9LL
United Kingdom
Telephone: (1) 631 360 2222
Fax: (1) 631 360 8222
[email protected]
Telephone: (852) 26100 611
Fax: (852) 24250 494
[email protected]
Telephone: (44) 161 622 4444
Fax: (44) 161 622 4446
[email protected]
© 2007 Published by Zetex Semiconductors plc
Issue 4 - June 2007
© Zetex Semiconductors plc 2007
10
www.zetex.com