Si5326 Data Sheet

Si5326
A N Y -F R E Q U E N C Y P R E C I S I O N C L O C K M U L T I P LI E R /J I T T E R
ATTENUATOR
Features
Description
CKOUT1–
CKOUT1+
NC
36 35 34 33 32 31 30 29 28
RST
1
27 SDI
NC
2
26 A2_SS
INT_C1B
3
25 A1
C2B
4
VDD
5
XA
6
XB
7
GND
8
20 INC
NC
9
19 DEC
24 A0
GND
Pad
23 SDA_SDO
22 SCL
21 CS_CA
Copyright © 2010 by Silicon Laboratories
LOL
CKIN1–
RATE1
CKIN1+
VDD
10 11 12 13 14 15 16 17 18
The Si5326 is a jitter-attenuating precision clock multiplier for applications
requiring sub 1 ps jitter performance. The Si5326 accepts two input clocks ranging
from 2 kHz to 710 MHz and generates two output clocks ranging from 2 kHz to
945 MHz and select frequencies to 1.4 GHz. The two outputs are divided down
separately from a common source. The Si5326 can also use its crystal oscillator
as a clock source for frequency synthesis. The device provides virtually any
frequency translation combination across this operating range. The Si5326 input
clock frequency and clock multiplication ratio are programmable through an I2C or
SPI interface. The Si5326 is based on Silicon Laboratories' 3rd-generation
DSPLL® technology, which provides frequency synthesis and jitter attenuation in a
highly integrated PLL solution that eliminates the need for external VCXO and
loop filter components. The DSPLL loop bandwidth is digitally programmable,
providing jitter performance optimization at the application level. Operating from a
single 1.8, 2.5, or 3.3 V supply, the Si5326 is ideal for providing clock
multiplication and jitter attenuation in high performance timing applications.
Rev. 1.0 9/10
GND
Optical modules
Wireless basestations
Data converter clocking
xDSL
PDH clock synthesis
Test and measurement
Broadcast video
NC







NC
SONET/SDH OC-48/OC-192/STM16/STM-64 line cards
 ITU G.709 and custom FEC line
cards
 GbE/10GbE, 1/2/4/8/10G Fibre
Channel line cards
 GbE/10GbE Synchronous Ethernet

CMODE
Applications
VDD
Pin Assignments
CKOUT2–

Ordering Information:
See page 65.
CKIN2–

CKOUT2+

Dual clock outputs with selectable
signal format
Support for ITU G.709 and custom
FEC ratios (255/238, 255/237,
255/236)
LOL, LOS, FOS alarm outputs
Digitally-controlled output phase
adjustment
I2C or SPI programmable
On-chip voltage regulator for
1.8 ±5%, 2.5 ±10%, or 3.3 V ±10%
operation
Small size: 6 x 6 mm 36-lead QFN
Pb-free, ROHS compliant
CKIN2+

Generates any frequency from 2 kHz 
to 945 MHz and select frequencies to
1.4 GHz from an input frequency of 
2 kHz to 710 MHz
Ultra-low jitter clock outputs with jitter

generation as low as 0.3 ps rms

(50 kHz–80 MHz)
Integrated loop filter with selectable
loop bandwidth (60 Hz to 8.4 kHz) 
Meets OC-192 GR-253-CORE jitter 
specifications
Dual clock inputs with manual or
automatically controlled hitless

switching (LVPECL, LVDS, CML,

CMOS)
RATE0

Si5326
Si5326
Functional Block Diagram
Xtal or Refclock
CKIN1
CKIN2
÷ N31
Hitless Switching
Mux
®
÷ N32
DSPLL
Xtal/Refclock
Loss of Signal/
Frequency Offset
Loss of Lock
CKOUT1
÷ N2_LS
CKOUT2
÷ N1_HS
÷ N2
VDD (1.8, 2.5, or 3.3 V)
Control
Signal Detect
I2C/SPI Port
GND
Clock Select
Device Interrupt
Rate Select
2
÷ N1_LS
Skew Control
Rev. 1.0
Si5326
TABLE O F C ONTENTS
1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2. Typical Phase Noise Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3. Typical Application Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
4. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.1. External Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.2. Further Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5. Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6. Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
7. Pin Descriptions: Si5326 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
8. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
9. Package Outline: 36-Pin QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
10. Recommended PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
11. Si5326 Device Top Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Rev. 1.0
3
Si5326
1. Electrical Specifications
Table 1. Recommended Operating Conditions
Parameter
Symbol
Ambient Temperature
TA
Supply Voltage during
Normal Operation
VDD
Test Condition
Min
Typ
Max
Unit
-40
25
85
C
3.3 V Nominal
2.97
3.3
3.63
V
2.5 V Nominal
2.25
2.5
2.75
V
1.8 V Nominal
1.71
1.8
1.89
V
Note: All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions.
Typical values apply at nominal supply voltages and an operating temperature of 25 ºC unless otherwise stated.
SIGNAL +
Differential I/Os VICM , VOCM
V
VISE , VOSE
SIGNAL –
(SIGNAL +) – (SIGNAL –)
Differential Peak-to-Peak Voltage
VID,VOD
VICM, VOCM
Single-Ended
Peak-to-Peak Voltage
t
SIGNAL +
VID = (SIGNAL+) – (SIGNAL–)
SIGNAL –
Figure 1. Differential Voltage Characteristics
80%
CKIN, CKOUT
20%
tF
tR
Figure 2. Rise/Fall Time Characteristics
4
Rev. 1.0
Si5326
Table 2. DC Characteristics
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
IDD
LVPECL Format
622.08 MHz Out
Both CKOUTs Enabled
—
251
279
mA
LVPECL Format
622.08 MHz Out
1 CKOUT Enabled
—
217
243
mA
CMOS Format
19.44 MHz Out
Both CKOUTs Enabled
—
204
234
mA
CMOS Format
19.44 MHz Out
1 CKOUT Enabled
—
194
220
mA
Disable Mode
—
165
—
mA
1.8 V ± 5%
0.9
—
1.4
V
2.5 V ± 10%
1
—
1.7
V
3.3 V ± 10%
1.1
—
1.95
V
CKNRIN
Single-ended
20
40
60
kΩ
Single-Ended Input
Voltage Swing
(See Absolute Specs)
VISE
fCKIN < 212.5 MHz
See Figure 1.
0.2
—
—
VPP
fCKIN > 212.5 MHz
See Figure 1.
0.25
—
—
VPP
Differential Input
Voltage Swing
(See Absolute Specs)
VID
fCKIN < 212.5 MHz
See Figure 1.
0.2
—
—
VPP
fCKIN > 212.5 MHz
See Figure 1.
0.25
—
—
VPP
LVPECL 100  load lineto-line
VDD –
1.42
—
VDD –1.25
V
Supply Current1
CKINn Input Pins2
Input Common Mode
Voltage (Input Threshold Voltage)
Input Resistance
VICM
Output Clocks (CKOUTn)3
Common Mode
CKOVCM
Notes:
1. Current draw is independent of supply voltage
2. No under- or overshoot is allowed.
3. LVPECL outputs require nominal VDD ≥ 2.5 V.
4. This is the amount of leakage that the 3-Level inputs can tolerate from an external driver. See Si53xx
Family Reference Manual for more details.
5. LVPECL, CML, LVDS and low-swing LVDS measured with Fo = 622.08 MHz.
Rev. 1.0
5
Si5326
Table 2. DC Characteristics (Continued)
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Differential Output
Swing
CKOVD
LVPECL 100  load lineto-line
1.1
—
1.9
VPP
Single Ended Output
Swing
CKOVSE
LVPECL 100  load lineto-line
0.5
—
0.93
VPP
Differential Output
Voltage
CKOVD
CML 100  load line-toline
350
425
500
mVPP
CKOVCM
CML 100  load line-toline
—
VDD-0.36
—
V
CKOVD
LVDS
100  load line-to-line
500
700
900
mVPP
Low Swing LVDS
100  load line-to-line
350
425
500
mVPP
CKOVCM
LVDS 100 load line-toline
1.125
1.2
1.275
V
CKORD
CML, LVPECL, LVDS
—
200
—

Output Voltage Low
CKOVOLLH
CMOS
—
—
0.4
V
Output Voltage High
CKOVOHLH
VDD = 1.71 V
CMOS
0.8 x
VDD
—
—
V
Common Mode Output
Voltage
Differential Output
Voltage
Common Mode Output
Voltage
Differential Output
Resistance
Notes:
1. Current draw is independent of supply voltage
2. No under- or overshoot is allowed.
3. LVPECL outputs require nominal VDD ≥ 2.5 V.
4. This is the amount of leakage that the 3-Level inputs can tolerate from an external driver. See Si53xx
Family Reference Manual for more details.
5. LVPECL, CML, LVDS and low-swing LVDS measured with Fo = 622.08 MHz.
6
Rev. 1.0
Si5326
Table 2. DC Characteristics (Continued)
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Output Drive Current
(CMOS driving into
CKOVOL for output low
or CKOVOH for output
high. CKOUT+ and
CKOUT– shorted
externally)
CKOIO
ICMOS[1:0] =11
VDD = 1.8 V
—
7.5
—
mA
ICMOS[1:0] =10
VDD = 1.8 V
—
5.5
—
mA
ICMOS[1:0] =01
VDD = 1.8 V
—
3.5
—
mA
ICMOS[1:0] =00
VDD = 1.8 V
—
1.75
—
mA
ICMOS[1:0] =11
VDD = 3.3 V
—
32
—
mA
ICMOS[1:0] =10
VDD = 3.3 V
—
24
—
mA
ICMOS[1:0] =01
VDD = 3.3 V
—
16
—
mA
ICMOS[1:0] =00
VDD = 3.3 V
—
8
—
mA
VDD = 1.71 V
—
—
0.5
V
VDD = 2.25 V
—
—
0.7
V
VDD = 2.97 V
—
—
0.8
V
VDD = 1.89 V
1.4
—
—
V
VDD = 2.25 V
1.8
—
—
V
VDD = 3.63 V
2.5
—
—
V
2-Level LVCMOS Input Pins
Input Voltage Low
Input Voltage High
VIL
VIH
Notes:
1. Current draw is independent of supply voltage
2. No under- or overshoot is allowed.
3. LVPECL outputs require nominal VDD ≥ 2.5 V.
4. This is the amount of leakage that the 3-Level inputs can tolerate from an external driver. See Si53xx
Family Reference Manual for more details.
5. LVPECL, CML, LVDS and low-swing LVDS measured with Fo = 622.08 MHz.
Rev. 1.0
7
Si5326
Table 2. DC Characteristics (Continued)
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
3-Level Input Pins4
Input Voltage Low
VILL
—
—
0.15 x VDD
V
Input Voltage Mid
VIMM
0.45 x
VDD
—
0.55 x VDD
V
Input Voltage High
VIHH
0.85 x
VDD
—
—
V
Input Low Current
IILL
See Note 4
–20
—
—
µA
Input Mid Current
IIMM
See Note 4
–2
—
+2
µA
Input High Current
IIHH
See Note 4
—
—
20
µA
VOL
IO = 2 mA
VDD = 1.71 V
—
—
0.4
V
IO = 2 mA
VDD = 2.97 V
—
—
0.4
V
IO = –2 mA
VDD = 1.71 V
VDD –
0.4
—
—
V
IO = –2 mA
VDD = 2.97 V
VDD –
0.4
—
—
V
RSTb = 0
–100
—
100
µA
LVCMOS Output Pins
Output Voltage Low
Output Voltage Low
Output Voltage High
VOH
Output Voltage High
Disabled Leakage
Current
IOZ
Notes:
1. Current draw is independent of supply voltage
2. No under- or overshoot is allowed.
3. LVPECL outputs require nominal VDD ≥ 2.5 V.
4. This is the amount of leakage that the 3-Level inputs can tolerate from an external driver. See Si53xx
Family Reference Manual for more details.
5. LVPECL, CML, LVDS and low-swing LVDS measured with Fo = 622.08 MHz.
8
Rev. 1.0
Si5326
Table 3. Microprocessor Control
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
I2C Bus Lines (SDA, SCL)
Input Voltage Low
VILI2C
—
—
0.25 x VDD
V
Input Voltage High
VIHI2C
0.7 x VDD
—
VDD
V
Input Current
Hysteresis of Schmitt
trigger inputs
Output Voltage Low
III2C
VIN = 0.1 x VDD
to 0.9 x VDD
–10
—
10
µA
VHYSI2C
VDD = 1.8V
0.1 x VDD
—
—
V
VDD = 2.5 or 3.3 V
0.05 x VDD
—
—
V
VDD = 1.8 V
IO = 3 mA
—
—
0.2 x VDD
V
VDD = 2.5 or 3.3 V
IO = 3 mA
—
—
0.4
V
VOLI2C
Rev. 1.0
9
Si5326
Table 3. Microprocessor Control (Continued)
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Duty Cycle, SCLK
tDC
SCLK = 10 MHz
40
—
60
%
Cycle Time, SCLK
tc
100
—
—
ns
Rise Time, SCLK
tr
20–80%
—
—
25
ns
Fall Time, SCLK
tf
20–80%
—
—
25
ns
Low Time, SCLK
tlsc
20–20%
30
—
—
ns
High Time, SCLK
thsc
80–80%
30
—
—
ns
Delay Time, SCLK Fall
to SDO Active
td1
—
—
25
ns
Delay Time, SCLK Fall
to SDO Transition
td2
—
—
25
ns
Delay Time, SS Rise
to SDO Tri-state
td3
—
—
25
ns
Setup Time, SS to
SCLK Fall
tsu1
25
—
—
ns
Hold Time, SS to
SCLK Rise
th1
20
—
—
ns
Setup Time, SDI to
SCLK Rise
tsu2
25
—
—
ns
Hold Time, SDI to
SCLK Rise
th2
20
—
—
ns
Delay Time between
Slave Selects
tcs
25
—
—
ns
SPI Specifications
10
Rev. 1.0
Si5326
Table 4. AC Specifications
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Single-Ended Reference Clock Input Pin XA (XB with cap to GND)
Input Resistance
XARIN
RATE[1:0] = LM, ML, MH,
or HM, ac coupled
—
12
—
k
Input Voltage Swing
XAVPP
RATE[1:0] = LM, ML, MH,
or HM, ac coupled
0.5
—
1.2
VPP
0.5
—
1.2
VPP,
each.
0.002
—
710
MHz
40
—
60
%
2
—
—
ns
—
—
3
pF
—
—
11
ns
N1  6
0.002
—
945
MHz
N1 = 5
970
—
1134
MHz
N1 = 4
1.213
—
1.4
GHz
—
—
212.5
MHz
Differential Reference Clock Input Pins (XA/XB)
Input Voltage Swing
XA/XBVPP
RATE[1:0] = LM, ML, MH,
or HM
CKINn Input Pins
Input Frequency
CKNF
Input Duty Cycle
(Minimum Pulse
Width)
CKNDC
Input Capacitance
CKNCIN
Input Rise/Fall Time
CKNTRF
Whichever is smaller
(i.e., the 40% / 60%
limitation applies only
to high frequency
clocks)
20–80%
See Figure 2
CKOUTn Output Pins
(See ordering section for speed grade vs frequency limits)
Output Frequency
(Output not configured for CMOS or
Disabled)
Maximum Output
Frequency in CMOS
Format
CKOF
CKOF
Output Rise/Fall
(20–80 %) @
622.08 MHz output
CKOTRF
Output not configured for
CMOS or Disabled
See Figure 2
—
230
350
ps
Output Rise/Fall
(20–80%) @
212.5 MHz output
CKOTRF
CMOS Output
VDD = 1.71
CLOAD = 5 pF
—
—
8
ns
Rev. 1.0
11
Si5326
Table 4. AC Specifications (Continued)
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Output Rise/Fall
(20–80%) @
212.5 MHz output
CKOTRF
CMOS Output
VDD = 2.97
CLOAD = 5 pF
—
—
2
ns
Output Duty Cycle
Uncertainty @
622.08 MHz
CKODC
100  Load
Line-to-Line
Measured at 50% Point
(Not for CMOS)
—
—
+/-40
ps
LVCMOS Input Pins
Minimum Reset Pulse
Width
tRSTMN
Reset to Microprocessor Access Ready
tREADY
Input Capacitance
1
Cin
µs
10
ms
—
—
3
pF
LVCMOS Output Pins
Rise/Fall Times
tRF
CLOAD = 20pf
See Figure 2
—
25
—
ns
LOSn Trigger Window
LOSTRIG
From last CKINn to 
Internal detection of LOSn
N3 ≠ 1
—
—
4.5 x N3
TCKIN
Time to Clear LOL
after LOS Cleared
tCLRLOL
LOS to LOL
Fold = Fnew
Stable Xa/XB reference
—
10
—
ms
Output Clock Skew
tSKEW
 of CKOUTn to  of
CKOUT_m, CKOUTn
and CKOUT_m at same
frequency and signal
format
PHASEOFFSET = 0
CKOUT_ALWAYS_ON = 1
SQ_ICAL = 1
—
—
100
ps
Phase Change due to
Temperature Variation
tTEMP
Max phase changes from
–40 to +85 °C
—
300
500
ps
Device Skew
12
Rev. 1.0
Si5326
Table 4. AC Specifications (Continued)
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
PLL Performance
(fin=fout = 622.08 MHz; BW=120 Hz; LVPECL)
Lock Time
tLOCKMP
Start of ICAL to of LOL
—
35
1200
ms
Output Clock Phase
Change
tP_STEP
After clock switch
f3  128 kHz
—
200
—
ps
—
0.05
0.1
dB
Jitter Frequency Loop
Bandwidth
5000/BW
—
—
ns pk-pk
1 kHz Offset
—
–106
–87
dBc/Hz
10 kHz Offset
—
–121
–100
dBc/Hz
100 kHz Offset
—
–132
–104
dBc/Hz
1 MHz Offset
—
–132
–119
dBc/Hz
Closed Loop Jitter
Peaking
JPK
Jitter Tolerance
JTOL
Phase Noise
fout = 622.08 MHz
CKOPN
Subharmonic Noise
SPSUBH
Phase Noise @ 100 kHz
Offset
—
–88
–76
dBc
Spurious Noise
SPSPUR
Max spur @ n x F3
(n  1, n x F3 < 100 MHz)
—
–93
–70
dBc
Rev. 1.0
13
Si5326
Table 5. Jitter Generation
Parameter
Jitter Gen
OC-192
Symbol
JGEN
Test Condition*
Measurement
Filter
DSPLL
BW2
0.02–80 MHz
120 Hz
4–80 MHz
0.05–80 MHz
Jitter Gen
OC-48
JGEN
0.12–20 MHz
Min
Typ
Max
GR-253Specification
Unit
—
4.2
6.2
30
psPP
—
.27
.42
N/A
psrms
—
3.7
6.4
10
psPP
—
.14
0.31
N/A
psrms
—
4.4
6.9
10
psPP
—
.26
0.41
1.0
ps rms
—
3.5
5.4
40.2
psPP
—
.27
0.41
4.02
ps rms
120 Hz
120 Hz
120 Hz
*Note: Test conditions:
1. fIN = fOUT = 622.08 MHz
2.
Clock input: LVPECL
3.
Clock output: LVPECL
4.
PLL bandwidth: 120 Hz
5.
114.285 MHz 3rd OT crystal used as XA/XB input
6.
VDD = 2.5 V
7.
TA = 85 °C
Table 6. Thermal Characteristics
(VDD = 1.8 ±5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Value
Unit
Thermal Resistance Junction to Ambient
JA
Still Air
32
C°/W
Thermal Resistance Junction to Case
JC
Still Air
14
C°/W
14
Rev. 1.0
Si5326
Table 7. Absolute Limits
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
—
3.8
V
VDD+0.3
V
DC Supply Voltage
VDD
–0.5
LVCMOS Input Voltage
VDIG
–0.3
CKINn Voltage Level Limits
CKNVIN
0
—
VDD
V
XA/XB Voltage Level Limits
XAVIN
0
—
1.2
V
Operating Junction Temperature
TJCT
–55
—
150
ºC
Storage Temperature Range
TSTG
–55
—
150
ºC
2
—
—
kV
ESD MM Tolerance; All pins
except CKIN+/CKIN–
150
—
—
V
ESD HBM Tolerance
(100 pF, 1.5 k); CKIN+/CKIN–
750
—
—
V
ESD MM Tolerance;
CKIN+/CKIN–
100
—
—
V
ESD HBM Tolerance
(100 pF, 1.5 k); All pins except
CKIN+/CKIN–
Latch-up Tolerance
JESD78 Compliant
Rev. 1.0
15
Si5326
2. Typical Phase Noise Performance
Figure 3. Typical Phase Noise Plot
Jitter Band
Jitter, RMS
SONET_OC48, 12 kHz to 20 MHz
249 fs
SONET_OC192_A, 20 kHz to 80 MHz
274 fs
SONET_OC192_B, 4 MHz to 80 MHz
166 fs
SONET_OC192_C, 50 kHz to 80 MHz
267 fs
Brick Wall_800 Hz to 80 MHz
274 fs
*Note: Jitter integration bands include low-pass (–20 dB/Dec) and hi-pass
(–60 dB/Dec) roll-offs per Telecordia GR-253-CORE.
16
Rev. 1.0
Si5326
3. Typical Application Circuit
C4 1 µF
System
Power
Supply
C1 0.1 µF
Ferrite
Bead
C2 0.1 µF
VDD = 3.3 V
C3 0.1 µF
130 
GND PAD
VDD
CKIN1+
GND
130 
CKIN1–
82 
Input
Clock
Sources*
–
0.1 µF
0.1 µF
Clock Outputs
CKOUT2+
VDD = 3.3 V
+
100 
–
CKOUT2–
130 
0.1 µF
INC
CKIN2+
82 
Interrupt/CKIN1 Invalid Indicator
INT_C1B
Si5326
Option 1:
Output Phase Control
DEC
CKIN2–
82 
+
100 
CKOUT1–
82 
130 
0.1 µF
CKOUT1+
C2B
CKIN2 Invalid Indicator
LOL
PLL Loss of Lock Indicator
XA
Crystal
XB
VDD
15 k
A[2:0]
RATE[1:0]2
Crystal/Ref Clk Rate
15 k
0.1 µF
Option 2:
Refclk+
XA
0.1 µF
Refclk–
Control Mode (L)
Serial Port Address
I2C Interface
SDA
Serial Data
SCL
Serial Clock
XB
CS_CA
CMODE
Clock Select/Clock Active
RST
Reset
Notes: 1. Assumes differential LVPECL termination (3.3 V) on clock inputs.
2. Denotes tri-level input pins with states designated as L (ground), M (VDD/2), and H (VDD).
3. I2C-required pull-up resistors not shown.
Figure 4. Si5326 Typical Application Circuit (I2C Control Mode)
Note: For an example schematic and layout, refer to the Si5325/26-EVB User’s Guide.
C4 1 µF
System
Power
Supply
C1 0.1 µF
Ferrite
Bead
C2 0.1 µF
VDD = 3.3 V
C3 0.1 µF
130 
82 
Input
Clock
Sources*
82 
GND PAD
CKIN1+
GND
VDD
130 
0.1 µF
CKOUT1+
+
100 
–
CKOUT1–
CKIN1–
0.1 µF
0.1 µF
Clock Outputs
CKOUT2+
VDD = 3.3 V
130 
+
100 
–
CKOUT2–
130 
0.1 µF
INC
CKIN2+
82 
82 
DEC
CKIN2–
INT_C1B
Si5326
Option 1:
XA
Output Phase Control
Interrupt/CLKIN1 Invalid Indicator
C2B
CLKIN2 Invalid Indicator
LOL
PLL Loss of Lock Indicator
SS
Slave Select
Crystal
XB
VDD
15 k
Crystal/Ref Clk Rate
RATE[1:0]2
15 k
Option 2:
SDO
0.1 µF
Refclk+
Refclk–
Control Mode (H)
Reset
SDI
XA
0.1 µF
SCLK
XB
CMODE
CS_CA
Serial Data Out
SPI Interface
Serial Data In
Serial Clock
Clock Select/Clock Active
RST
Notes: 1. Assumes differential LVPECL termination (3.3 V) on clock inputs.
2. Denotes tri-level input pins with states designated as L (ground), M (VDD/2), and H (VDD).
Figure 5. Si5326 Typical Application Circuit (SPI Control Mode)
Note: For an example schematic and layout, refer to the Si5325/26-EVB User’s Guide.
Rev. 1.0
17
Si5326
4. Functional Description
Xtal or Refclock
CKIN1
CKIN2
÷ N31
Hitless Switching
Mux
®
÷ N32
DSPLL
Xtal/Refclock
Loss of Signal/
Frequency Offset
Loss of Lock
÷ N1_LS
CKOUT1
÷ N2_LS
CKOUT2
÷ N1_HS
÷ N2
VDD (1.8, 2.5, or 3.3 V)
Control
Signal Detect
I2C/SPI Port
GND
Clock Select
Skew Control
Device Interrupt
Rate Select
Figure 6. Functional Block Diagram
The Si5326 is a jitter-attenuating precision clock
multiplier for applications requiring sub 1 ps jitter
performance. The Si5326 accepts two input clocks
ranging from 2 kHz to 710 MHz and generates two
output clocks ranging from 2 kHz to 945 MHz and select
frequencies to 1.4 GHz. The Si5326 can also use its
crystal oscillator as a clock source for frequency
synthesis. The device provides virtually any frequency
translation combination across this operating range.
Independent dividers are available for each input clock
and output clock, so the Si5326 can accept input clocks
at different frequencies and it can generate output
clocks at different frequencies. The Si5326 input clock
frequency and clock multiplication ratio are
programmable through an I2C or SPI interface. Silicon
Laboratories offers a PC-based software utility,
DSPLLsim, that can be used to determine the optimum
PLL divider settings for a given input frequency/clock
multiplication ratio combination that minimizes phase
noise and power consumption. This utility can be
downloaded from http://www.silabs.com/timing.
The Si5326 is based on Silicon Laboratories' 3rdgeneration DSPLL® technology, which provides any
frequency synthesis and jitter attenuation in a highly
integrated PLL solution that eliminates the need for
external VCXO and loop filter components. The Si5326
PLL loop bandwidth is digitally programmable and
supports a range from 60 Hz to 8.4 kHz. The DSPLLsim
software utility can be used to calculate valid loop
bandwidth settings for a given input clock
frequency/clock multiplication ratio.
18
The Si5326 supports hitless switching between the two
synchronous input clocks in compliance with GR-253CORE that greatly minimizes the propagation of phase
transients to the clock outputs during an input clock
transition (maximum 200 ps phase change). Manual
and automatic revertive and non-revertive input clock
switching options are available. The Si5326 monitors
both input clocks for loss-of-signal (LOS) and provides a
LOS alarm (INT_C1B and C2B) when it detects missing
pulses on either input clock. The device monitors the
lock status of the PLL. The lock detect algorithm works
by continuously monitoring the phase of the input clock
in relation to the phase of the feedback clock. The
Si5326 also monitors frequency offset alarms (FOS),
which indicate if an input clock is within a specified
frequency band relative to the frequency of a reference
clock. Both Stratum 3/3E and SONET Minimum Clock
(SMC) FOS thresholds are supported.The Si5326
provides a digital hold capability that allows the device
to continue generation of a stable output clock when the
selected input reference is lost. During digital hold, the
DSPLL generates an output frequency based on a
historical average frequency that existed for a fixed
amount of time before the error event occurred,
eliminating the effects of phase and frequency
transients that may occur immediately preceding digital
hold.
Rev. 1.0
Si5326
The Si5326 has two differential clock outputs. The
electrical format of each clock output is independently
programmable to support LVPECL, LVDS, CML, or
CMOS loads. If not required, the second clock output
can be powered down to minimize power consumption.
The phase difference between the selected input clock
and the output clocks is adjustable in 200 ps increments
for system skew control using the CLAT[7:0] register.
Fine phase adjustment is available and is set using the
FLAT register bits. The nominal range and resolution of
the FLAT[14:0] skew adjustment word are: ±110 ps and
3 ps, respectively. In addition, the phase of one output
clock may be adjusted in relation to the phase of the
other output clock. The resolution varies from 800 ps to
2.2 ns depending on the PLL divider settings. See
Table 8 for instructions on ensuring output-to-output
alignment. The input to output skew is not specified.
The DSPLLsim software utility determines the phase
offset resolution for a given input clock/clock
multiplication ratio combination. For system-level
debugging, a bypass mode is available which drives the
output clock directly from the input clock, bypassing the
internal DSPLL. The device is powered by a single 1.8,
2.5, or 3.3 V supply.
4.1. External Reference
An external, high quality clock or a low-cost
114.285 MHz 3rd overtone crystal is used as part of a
fixed-frequency oscillator within the DSPLL. This
external reference is required for the device to perform
jitter attenuation. Silicon Laboratories recommends
using a high quality crystal. Specific recommendations
may be found in the Family Reference Manual.
In digital hold, the DSPLL remains locked and tracks the
external reference. Note that crystals can have
temperature sensitivities.
4.2. Further Documentation
Consult the Silicon Laboratories Si53xx Any Frequency
Precision Clock Family Reference Manual (FRM) for
detailed information about the Si5326 functions.
Additional design support is available from Silicon
Laboratories through your distributor.
Silicon Laboratories has developed a PC-based
software utility called DSPLLsim to simplify device
configuration, including frequency planning and loop
bandwidth selection. The FRM and this utility can be
downloaded from http://www.silabs.com/timing.
Table 8. CKOUT_ALWAYS_ON and SQ_ICAL Truth Table
CKOUT_ALWAYS_ON
SQ_ICAL
Results
0
0
CKOUT OFF until after the first ICAL
0
1
CKOUT OFF until after the first successful
ICAL (i.e., when LOL is low)
1
0
CKOUT always ON, including during an ICAL
1
1
CKOUT always ON, including during an ICAL.
Use these settings to preserve output-to-output
skew
Rev. 1.0
19
Si5326
5. Register Map
All register bits that are not defined in this map should always be written with the specified Reset Values. The
writing to these bits of values other than the specified Reset Values may result in undefined device behavior.
Registers not listed, such as Register 64, should never be written to.
Register
D7
0
D6
D5
D4
FREE_RUN
CKOUT_
ALWAYS_
ON
D3
D2
D1
BYPASS_
REG
1
CK_PRIOR2[1:0]
2
D0
CK_PRIOR[1:0]
BWSEL_REG[3:0]
3
CKSEL_REG[1:0]
4
AUTOSEL_REG[1:0]
5
ICMOS[1:0]
6
DHOLD
SQ_ICAL
HST_DEL[4:0]
SLEEP
SFOUT2_REG[2:0]
SFOUT1_REG[2:0]
7
FOSREFSEL[2:0]
8
HLOG_2[1:0]
HLOG_1[1:0]
9
HIST_AVG[4:0]
10
DSBL2_
REG
DSBL1_
REG
11
PD_CK2
16
PD_CK1
CLAT[7:0]
17
FLAT_VALID
FLAT[14:8]
18
FLAT[7:0]
19
FOS_EN
FOS_THR[1:0]
VALTIME[1:0]
20
CK2_
BAD_
PIN
LOCK[T2:0]
LOL_PIN
INT_PIN
CK1_ACTV_PIN
CKSEL_PIN
CK_BAD_
POL
LOL_POL
INT_POL
23
LOS2_MSK
LOS1_MSK
LOSX_MSK
24
FOS2_MSK
FOS1_MSK
LOL_MSK
21
CK1_
BAD_
PIN
INCDEC_
PIN
22
CK_ACTV_
POL
25
N1_HS[2:0]
31
NC1_LS[19:16]
32
NC1_LS[15:8]
20
Rev. 1.0
Si5326
Register
D7
D6
D5
33
D4
D3
D2
D1
NC1_LS[7:0]
34
NC2_LS[19:16]
35
NC2_LS[15:8]
36
NC2_LS[7:0]
40
N2_HS[2:0]
N2_LS[19:16]
41
N2_LS[15:8]
42
N2_LS[7:0]
43
N31[18:16]
44
N31[15:8]
45
N31[7:0]
46
N32[18:16]
47
N32[15:8]
48
N32[7:0]
55
CLKIN2RATE[2:0]
CLKIN1RATE[2:0]
128
129
130
CLATPROGRESS
DIGHOLDVALID
131
132
FOS2_FLG
134
PARTNUM_RO[3:0]
CK1_ACTV_REG
LOS2_INT
LOS1_INT
LOSX_INT
FOS2_INT
FOS1_INT
LOL_INT
LOS2_FLG
LOS1_FLG
LOSX_FLG
FOS1_FLG
LOL_FLG
RST_REG
REVID_RO[3:0]
ICAL
GRADE_RO[1:0]
138
139
CK2_ACTV_REG
PARTNUM_RO[11:4]
135
136
D0
LOS2_EN
[0:0]
LOS1_EN
[0:0]
142
INDEPENDENTSKEW1[7:0]
143
INDEPENDENTSKEW2[7:0]
Rev. 1.0
LOS2_EN
[1:1]
LOS1_EN
[1:1]
FOS2_EN
FOS1_EN
21
Si5326
6. Register Descriptions
Register 0.
Bit
D7
Name
Type
D6
D5
FREE_
RUN
CKOUT_
ALWAYS_
ON
R/W
R/W
R
D4
D3
D2
D1
D0
BYPASS_
REG
R
R
R
R/W
R
Reset value = 0001 0100
Bit
Name
7
Reserved
6
FREE_RUN
5
Reserved.
Free Run.
Internal to the device, route XA/XB to CKIN2. This allows the device to lock to its XA-XB
reference.
0: Disable
1: Enable
CKOUT_
CKOUT Always On.
ALWAYS_ON This will bypass the SQ_ICAL function. Output will be available even if SQ_ICAL is on
and ICAL is not complete or successful. See Table 8 on page 19.
0: Squelch output until part is calibrated (ICAL).
1: Provide an output. Note: The frequency may be significantly off and variable until the
part is calibrated.
4:2
Reserved
Reserved.
1
BYPASS_
REG
Bypass Register.
Reserved
Reserved.
0
22
Function
This bit enables or disables the PLL bypass mode. Use only when the device is in digital
hold or before the first ICAL.
0: Normal operation
1: Bypass mode. Selected input clock is connected to CKOUT buffers, bypassing the
PLL. Bypass mode does not support CMOS clock outputs.
Rev. 1.0
Si5326
Register 1.
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
Reserved
CK_PRIOR2 [1:0]
CK_PRIOR1 [1:0]
Type
R
R/W
R/W
Reset value = 1110 0100
Bit
Name
7:4
Reserved
3:2
CK_PRIOR2
[1:0]
1:0
CK_PRIOR1
[1:0]
Function
Reserved.
CK_PRIOR 2.
Selects which of the input clocks will be 2nd priority in the autoselection state machine.
00: CKIN1 is 2nd priority.
01: CKIN2 is 2nd priority.
10: Reserved
11: Reserved
CK_PRIOR 1.
Selects which of the input clocks will be 1st priority in the autoselection state machine.
00: CKIN1 is 1st priority.
01: CKIN2 is 1st priority.
10: Reserved
11: Reserved
Register 2.
Bit
D7
D6
D5
D4
D3
D2
D1
Name
BWSEL_REG [3:0]
Reserved
Type
R/W
R
D0
Reset value = 0100 0010
Bit
7:4
3:0
Name
Function
BWSEL_REG BWSEL_REG.
[3:0]
Selects nominal f3dB bandwidth for PLL. See DSPLLsim for settings. After BWSEL_REG
is written with a new value, an ICAL is required for the change to take effect.
Reserved
Reserved.
Rev. 1.0
23
Si5326
Register 3.
Bit
D7
D6
D5
D4
D3
D2
D1
Name
CKSEL_REG [1:0]
DHOLD
SQ_ICAL
Reserved
Type
R/W
R/W
R/W
R
D0
Reset value = 0000 0101
Bit
7:6
5
Name
Function
CKSEL_REG CKSEL_REG.
[1:0]
If the device is operating in register-based manual clock selection mode
(AUTOSEL_REG = 00), and CKSEL_PIN = 0, then these bits select which input clock
will be the active input clock. If CKSEL_PIN = 1 and AUTOSEL_REG = 00, the CS_CA
input pin continues to control clock selection and CKSEL_REG is of no consequence.
00: CKIN_1 selected.
01: CKIN_2 selected.
10: Reserved
11: Reserved
DHOLD
DHOLD.
Forces the part into digital hold. This bit overrides all other manual and automatic clock
selection controls.
0: Normal operation.
1: Force digital hold mode. Overrides all other settings and ignores the quality of all of the
input clocks.
4
SQ_ICAL
SQ_ICAL.
This bit determines if the output clocks will remain enabled or be squelched (disabled)
during an internal calibration. See Table 8 on page 19.
0: Output clocks enabled during ICAL.
1: Output clocks disabled during ICAL.
3:0
24
Reserved
Reserved.
Rev. 1.0
Si5326
Register 4.
Bit
D7
D6
D5
D4
D3
D2
Name
AUTOSEL_REG [1:0]
Reserved
HIST_DEL [4:0]
Type
R/W
R
R/W
D1
D0
Reset value = 0001 0010
Bit
Name
Function
7:6
AUTOSEL_
REG [1:0]
AUTOSEL_REG [1:0].
Selects method of input clock selection to be used.
00: Manual (either register or pin controlled, see CKSEL_PIN)
01: Automatic Non-Revertive
10: Automatic Revertive
11: Reserved
See the Si53xx Family Reference Manual for a detailed description.
5
Reserved
Reserved.
4:0
HIST_DEL
[4:0]
HIST_DEL [4:0].
Selects amount of delay to be used in generating the history information used for Digital
Hold.
See the Si53xx Family Reference Manual for a detailed description.
Register 5.
Bit
D7
D6
D5
D4
D3
D2
Name
ICMOS [1:0]
Reserved
Type
R/W
R
D1
D0
Reset value = 1110 1101
Bit
Name
7:6
ICMOS [1:0]
Function
ICMOS [1:0].
When the output buffer is set to CMOS mode, these bits determine the output buffer drive
strength. The first number below refers to 3.3 V operation; the second to 1.8 V operation.
These values assume CKOUT+ is tied to CKOUT-.
00: 8mA/2mA
01: 16mA/4mA
10: 24mA/6mA
11: 32mA/8mA
5:0
Reserved
Reserved.
Rev. 1.0
25
Si5326
Register 6.
Bit
D7
D6
D5
D4
D3
D2
D1
Name
Reserved
SLEEP
SFOUT2_REG [2:0]
SFOUT1_REG [2:0]
Type
R
R/W
R/W
R/W
D0
Reset value = 0010 1101
Bit
Name
7
Reserved
6
SLEEP
Function
Reserved.
SLEEP.
In sleep mode, all clock outputs are disabled and the maximum amount of internal circuitry is powered down to reduce power dissipation and noise generation. This bit overrides the SFOUTn_REG[2:0] output signal format settings.
0: Normal operation
1: Sleep mode
5:3
2:0
26
SFOUT2_
REG [2:0]
SFOUT1_
REG [2:0]
SFOUT2_REG [2:0].
Controls output signal format and disable for CKOUT2 output buffer.
000: Reserved
001: Disable
010: CMOS (Bypass mode not supported)
011: Low swing LVDS
100: Reserved
101: LVPECL
110: CML
111: LVDS
Note: LVPECL requires a nominal VDD  2.5 V.
SFOUT1_REG [2:0].
Controls output signal format and disable for CKOUT1 output buffer.
000: Reserved
001: Disable
010: CMOS (Bypass mode not supported)
011: Low swing LVDS
100: Reserved
101: LVPECL
110: CML
111: LVDS
Note: LVPECL requires a nominal VDD  2.5 V.
Rev. 1.0
Si5326
Register 7.
Bit
D7
D6
D5
D4
D3
D2
D1
Name
Reserved
FOSREFSEL [2:0]
Type
R
R/W
D0
Reset value = 0010 1010
Bit
Name
7:3
Reserved.
2:0
Function
Reserved.
FOSREFSEL FOSREFSEL [2:0].
[2:0]
Selects which input clock is used as the reference frequency for frequency offset (FOS)
alarms.
000: XA/XB (External reference)
001: CKIN1
010: CKIN2
011: Reserved
100: Reserved
101: Reserved
110: Reserved
111: Reserved
Rev. 1.0
27
Si5326
Register 8.
Bit
D7
D6
D5
D4
D3
D2
D1
Name
HLOG_2[1:0]
HLOG_1[1:0]
Reserved
Type
R/W
R/W
R
D0
Reset value = 0000 0000
Bit
7:6
Name
Function
HLOG_2 [1:0] HLOG_2 [1:0].
00: Normal operation
01: Holds CKOUT2 output at static logic 0. Entrance and exit from this state will occur
without glitches or runt pulses.
10: Holds CKOUT2 output at static logic 1. Entrance and exit from this state will occur
without glitches or runt pulses.
11: Reserved
5:4
HLOG_1 [1:0].
00: Normal operation
01: Holds CKOUT1 output at static logic 0. Entrance and exit from this state will occur
without glitches or runt pulses.
10: Holds CKOUT1 output at static logic 1. Entrance and exit from this state will occur
without glitches or runt pulses.
11: Reserved
3:0
Reserved
Reserved.
Register 9.
Bit
D7
D6
D5
Name
HIST_AVG [4:0]
Type
R/W
D4
D3
D2
D1
D0
Reserved
R
R
R
Reset value = 1100 0000
Bit
Name
7:3
HIST_AVG
[4:0]
2:0
28
Reserved
Function
HIST_AVG [4:0].
Selects amount of averaging time to be used in generating the history information for
Digital Hold.
See the Si53xx Family Reference Manual for a detailed description
Reserved.
Rev. 1.0
Si5326
Register 10.
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
Reserved
DSBL2_
REG
DSBL1_
REG
Reserved
Reserved
Type
R
R/W
R/W
R
R
Reset value = 0000 0000
Bit
Name
7:4
Reserved
3
Function
Reserved.
DSBL2_REG DSBL2_REG.
This bit controls the powerdown of the CKOUT2 output buffer. If disable mode is
selected, the N2_LS output divider is also powered down.
0: CKOUT2 enabled
1: CKOUT2 disabled
2
DSBL1_REG DSBL1_REG.
This bit controls the powerdown of the CKOUT1 output buffer. If disable mode is
selected, the N1_LS output divider is also powered down.
0: CKOUT1 enabled
1: CKOUT1 disabled
1:0
Reserved
Reserved.
Rev. 1.0
29
Si5326
Register 11.
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
Reserved
PD_CK2
PD_CK1
Type
R
R/W
R/W
D1
D0
Reset value = 0100 0000
Bit
Name
Function
7:2
Reserved
Reserved.
1
PD_CK2
PD_CK2.
This bit controls the powerdown of the CKIN2 input buffer.
0: CKIN2 enabled
1: CKIN2 disabled
0
PD_CK1
PD_CK1.
This bit controls the powerdown of the CKIN1 input buffer.
0: CKIN1 enabled
1: CKIN1 disabled
Register 16.
Bit
D7
D6
D5
D4
D3
Name
CLAT [7:0]
Type
R/W
D2
Reset value = 0000 0000
Bit
Name
7:0
CLAT [7:0]
Function
CLAT [7:0].
With INCDEC_PIN = 0, this register sets the phase delay for CKOUTn in units of
1/Fosc. This can take as long as 20 seconds.
01111111 = 127/Fosc (2s compliment)
00000000 = 0
10000000 = -128/Fosc (2s compliment)
If NI_HS[2:0] = 000, increasing CLAT does not work.
30
Rev. 1.0
Si5326
Register 17.
Bit
D7
D6
D5
D4
D3
Name
FLAT_
VALID
FLAT [14:8]
Type
R/W
R/W
D2
D1
D0
Reset value = 1000 0000
Bit
7
Name
Function
FLAT_VALID FLAT_VALID.
Before writing a new FLAT[14:0] value, this bit must be set to zero, which causes the
existing FLAT[14:0] value to be held internally for use while the new value is being written. Once the new FLAT[14:0] value is completely written, set FLAT_VALID = 1 to enable
its use.
0: Memorize existing FLAT[14:0] value and ignore intermediate register values during
write of new FLAT[14:0] value.
1: Use FLAT[14:0] value directly from registers.
6:0
FLAT [14:8]
FLAT [14:8].
Fine resolution control for overall device skew from input clocks to output clocks. Positive
values increase the skew. See DSPLLsim for details.
FLAT [14:0] is a 2’s complement number.
Register 18.
Bit
D7
D6
D5
D4
D3
Name
FLAT [7:0]
Type
R/W
D2
D1
D0
Reset value = 0000 0000
Bit
Name
7:0
FLAT [7:0]
Function
FLAT [7:0].
Fine resolution control for overall device skew from input clocks to output clocks. Positive
values increase the skew. See DSPLLsim for details.
FLAT [14:0] is a 2’s complement number.
Rev. 1.0
31
Si5326
Register 19.
Bit
D7
D6
D5
D4
D3
D2
D1
Name
FOS_EN
FOS_THR [1:0]
VALTIME [1:0]
LOCKT [2:0]
Type
R/W
R/W
R/W
R/W
D0
Reset value = 0010 1100
Bit
Name
7
FOS_EN
Function
FOS_EN.
Frequency Offset Enable globally disables FOS. See the individual FOS enables (FOSX_EN, register 139).
0: FOS disable
1: FOS enabled by FOSx_EN
6:5
4:3
FOS_THR
[1:0]
FOS_THR [1:0].
Frequency Offset at which FOS is declared (relative to the selected FOS reference):
00: ± 11 to 12 ppm (Stratum 3/3E compliant, with a Stratum 3/3E used for REFCLK
01: ± 48 to 49 ppm (SMC)
10: ± 30 ppm (SONET Minimum Clock (SMC), with a Stratum 3/3E used for REFCLK.
11: ± 200 ppm
VALTIME [1:0] VALTIME [1:0].
Sets amount of time for input clock to be valid before the associated alarm is removed.
00: 2 ms
01: 100 ms
10: 200 ms
11: 13 seconds
2:0
LOCKT [2:0]
LOCKT [2:0].
Sets retrigger interval for one shot monitoring phase detector output. One shot is triggered by phase slip in DSPLL. Refer to the Si53xx Family Reference Manual for more
details.
000: 106 ms
001: 53 ms
010: 26.5 ms
011: 13.3 ms
100: 6.6 ms
101: 3.3 ms
110: 1.66 ms
111: .833 ms
32
Rev. 1.0
Si5326
Register 20.
Bit
D7
D6
D5
Name
Reserved
Type
R
D4
D3
D2
CK2_BAD_ CK1_BAD_
PIN
PIN
R/W
R/W
D1
D0
LOL_PIN
INT_PIN
R/W
R/W
Reset value = 0011 1110
Bit
Name
7:4
Reserved
3
CK2_BAD_
PIN
CK2_BAD_PIN.
CK1_BAD_
PIN
CK1_BAD_PIN.
2
1
LOL_PIN
Function
Reserved.
The CK2_BAD status can be reflected on the C2B output pin.
0: C2B output pin tristated
1: C2B status reflected to output pin
Either LOS1 or INT (see INT_PIN) status can be reflected on the INT_C1B output pin.
0: INT_C1B output pin tristated
1: LOS1 or INT (see INT_PIN) status reflected to output pin
LOL_PIN.
The LOL_INT status bit can be reflected on the LOL output pin.
0: LOL output pin tristated
1: LOL_INT status reflected to output pin
0
INT_PIN
INT_PIN.
Reflects the interrupt status on the INT_C1B output pin.
0: Interrupt status not displayed on INT_C1B output pin. Instead, the INT_C1B pin
indicates when CKIN1 is bad. If CK1_BAD_PIN = 0, INT_C1B output pin is tristated.
1: Interrupt status reflected to output pin.
Rev. 1.0
33
Si5326
Register 21.
Bit
D7
Name
INCDEC_
PIN
Type
R/W
D6
D5
D4
D3
D2
Reserved
Force 1
R
R
R
R
D1
D0
CK1_ACTV_PIN
CKSEL_
PIN
R/W
R/W
Reset value = 1111 1111
Bit
Name
7
INCDEC_PIN
Function
INCDEC_PIN.
Determines how coarse skew adjustments can be made. The adjustments can be made
via hardware using the INC/DEC pins or via software using the CLAT register.
0: INC and DEC inputs ignored; use CLAT register to adjust skew.
1: INC and DEC inputs control output phase increment/decrement.
6:2
Reserved
Reserved.
1
CK1_ACTV_ CK1_ACTV_PIN.
PIN
The CK1_ACTV_REG status bit can be reflected to the CS_CA output pin using the
CK1_ACTV_PIN enable function. CK1_ACTV_PIN is of consequence only when pin controlled clock selection is being used. (See CKSEL_PIN)
0: CS_CA output pin tristated.
1: Clock Active status reflected to output pin.
0
CKSEL_PIN
CKSEL_PIN.
If manual clock selection is being used, clock selection can be controlled via the
CKSEL_REG[1:0] register bits or the CS_CA input pin. This bit is only active when
AUTOSEL_REG = Manual.
0: CS_CA pin is ignored. CKSEL_REG[1:0] register bits control clock selection.
1: CS_CA input pin controls clock selection.
34
Rev. 1.0
Si5326
Register 22.
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
Reserved
CK_ACTV_POL
CK_BAD_
POL
LOL_POL
INT_POL
Type
R
R/W
R/W
R/W
R/W
Reset value = 1101 1111
Bit
Name
7:4
Reserved
3
CK_ACTV_
POL
CK_ACTV_POL.
CK_BAD_
POL
CK_BAD_POL.
LOL_POL
LOL_POL.
2
1
Function
Reserved.
Sets the active polarity for the CS_CA signals when reflected on an output pin.
0: Active low
1: Active high
Sets the active polarity for the INT_C1B and C2B signals when reflected on output pins.
0: Active low
1: Active high
Sets the active polarity for the LOL status when reflected on an output pin.
0: Active low
1: Active high
0
INT_POL
INT_POL.
Sets the active polarity for the interrupt status when reflected on the INT_C1B output pin.
0: Active low
1: Active high
Rev. 1.0
35
Si5326
Register 23.
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
Reserved
LOS2_
MSK
LOS1_
MSK
LOSX_
MSK
Type
R
R/W
R/W
R/W
Reset value = 0001 1111
Bit
Name
7:3
Reserved
2
LOS2_MSK
Function
Reserved.
LOS2_MSK.
Determines if a LOS on CKIN2 (LOS2_FLG) is used in the generation of an interrupt.
Writes to this register do not change the value held in the LOS2_FLG register.
0: LOS2 alarm triggers active interrupt on INT_C1B output (if INT_PIN=1).
1: LOS2_FLG ignored in generating interrupt output.
1
LOS1_MSK
LOS1_MSK.
Determines if a LOS on CKIN1 (LOS1_FLG) is used in the generation of an interrupt.
Writes to this register do not change the value held in the LOS1_FLG register.
0: LOS1 alarm triggers active interrupt on INT_C1B output (if INT_PIN=1).
1: LOS1_FLG ignored in generating interrupt output.
0
LOSX_MSK
LOSX_MSK.
Determines if a LOS on XA/XB(LOSX_FLG) is used in the generation of an interrupt.
Writes to this register do not change the value held in the LOSX_FLG register.
0: LOSX alarm triggers active interrupt on INT_C1B output (if INT_PIN=1).
1: LOSX_FLG ignored in generating interrupt output.
36
Rev. 1.0
Si5326
Register 24.
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
Reserved
FOS2_
MSK
FOS1_
MSK
LOL_MSK
Type
R
R/W
R/W
R/W
Reset value = 0011 1111
Bit
Name
7:3
Reserved
2
FOS2_MSK
Function
Reserved.
FOS2_MSK.
Determines if the FOS2_FLG is used in the generation of an interrupt. Writes to this register do not change the value held in the FOS2_FLG register.
0: FOS2 alarm triggers active interrupt on INT_C1B output (if INT_PIN=1).
1: FOS2_FLG ignored in generating interrupt output.
1
FOS1_MSK
FOS1_MSK.
Determines if the FOS1_FLG is used in the generation of an interrupt. Writes to this register do not change the value held in the FOS1_FLG register.
0: FOS1 alarm triggers active interrupt on INT_C1B output (if INT_PIN=1).
1: FOS1_FLG ignored in generating interrupt output.
0
LOL_MSK
LOL_MSK.
Determines if the LOL_FLG is used in the generation of an interrupt. Writes to this register do not change the value held in the LOL_FLG register.
0: LOL alarm triggers active interrupt on INT_C1B output (if INT_PIN=1).
1: LOL_FLG ignored in generating interrupt output.
Rev. 1.0
37
Si5326
Register 25.
Bit
D7
D6
D5
D4
D3
D2
D1
Name
N1_HS [2:0]
Reserved
Type
R/W
R
D0
Reset value = 0010 0000
Bit
Name
7:5
N1_HS [2:0]
Function
N1_HS [2:0].
Sets value for N1 high speed divider which drives NCn_LS (n = 1 to 2) low-speed divider.
000: N1= 4 Note: Changing the coarse skew via the INC pin or CLAT register is disabled
for this value.
001: N1= 5
010: N1= 6
011: N1= 7
100: N1= 8
101: N1= 9
110: N1= 10
111: N1= 11
4:0
Reserved
Reserved.
Register 31.
Bit
D7
D6
D5
D4
D3
D2
D1
Name
Reserved
NC1_LS [19:16]
Type
R
R/W
D0
Reset value = 0000 0000
38
Bit
Name
Function
7:4
Reserved
Reserved.
3:0
NC1_LS
[19:16]
NC1_LS [19:16].
Sets value for NC1 low-speed divider, which drives CKOUT1 output. Must be 0 or odd.
00000000000000000000 = 1
00000000000000000001 = 2
00000000000000000011 = 4
00000000000000000101 = 6
...
11111111111111111111=2^20
Valid divider values=[1, 2, 4, 6, ..., 2^20]
Rev. 1.0
Si5326
Register 32.
Bit
D7
D6
D5
D4
D3
Name
NC1_LS [15:8]
Type
R/W
D2
D1
D0
Reset value = 0000 0000
Bit
Name
7:0
NC1_LS
[15:8]
Function
NC1_LS [15:8].
Sets value for NC1 low-speed divider, which drives CKOUT1 output. Must be 0 or odd.
00000000000000000000 = 1
00000000000000000001 = 2
00000000000000000011 = 4
00000000000000000101 = 6
...
11111111111111111111=2^20
Valid divider values=[1, 2, 4, 6, ..., 2^20]
Register 33.
Bit
D7
D6
D5
D4
D3
Name
NC1_LS [7:0]
Type
R/W
D2
D1
D0
Reset value = 0011 0001
Bit
Name
7:0
NC1_LS
[19:0]
Function
NC1_LS [7:0].
Sets value for N1 low-speed divider, which drives CKOUT1 output. Must be 0 or odd.
00000000000000000000 = 1
00000000000000000001 = 2
00000000000000000011 = 4
00000000000000000101 = 6
...
11111111111111111111=2^20
Valid divider values=[1, 2, 4, 6, ..., 2^20]
Rev. 1.0
39
Si5326
Register 34.
Bit
D7
D6
D5
D4
D3
D2
D1
Name
Reserved
NC2_LS [19:16]
Type
R
R/W
D0
Reset value = 0000 0000
Bit
Name
Function
7:4
Reserved
Reserved.
3:0
NC2_LS
[19:16]
NC2_LS [19:16].
Sets value for NC2 low-speed divider, which drives CKOUT2 output. Must be 0 or odd.
00000000000000000000=1
00000000000000000001=2
00000000000000000011=4
00000000000000000101=6
...
11111111111111111111=2^20
Valid divider values=[1, 2, 4, 6, ..., 2^20]
Register 35.
Bit
D7
D6
D5
D4
D3
Name
NC2_LS [15:8]
Type
R/W
D2
D1
D0
Reset value = 0000 0000
40
Bit
Name
7:0
NC2_LS
[15:8]
Function
NC2_LS [15:8].
Sets value for NC2 low-speed divider, which drives CKOUT2 output. Must be 0 or odd.
00000000000000000000 = 1
00000000000000000001 = 2
00000000000000000011 = 4
00000000000000000101 = 6
...
11111111111111111111=2^20
Valid divider values=[1, 2, 4, 6, ..., 2^20]
Rev. 1.0
Si5326
Register 36.
Bit
D7
D6
D5
D4
D3
Name
NC2_LS [7:0]
Type
R/W
D2
D1
D0
Reset value = 0011 0001
Bit
7:0
Name
Function
NC2_LS [7:0] NC2_LS [7:0].
Sets value for NC2 low-speed divider, which drives CKOUT2 output. Must be 0 or odd.
00000000000000000000 = 1
00000000000000000001 = 2
00000000000000000011 = 4
00000000000000000101 = 6
...
11111111111111111111=2^20
Valid divider values=[1, 2, 4, 6, ..., 2^20]
Rev. 1.0
41
Si5326
Register 40.
Bit
D7
D6
D5
D4
D3
D2
D1
Name
N2_HS [2:0]
Reserved
N2_LS [19:16]
Type
R/W
R
R/W
Reset value = 1100 0000
Bit
Name
7:5
N2_HS [2:0]
Function
N2_HS [2:0].
Sets value for N2 high speed divider, which drives N2LS low-speed divider.
000: 4
001: 5
010: 6
011: 7
100: 8
101: 9
110: 10
111: 11
4
3:0
Reserved
Reserved.
N2_LS [19:16] N2_LS [19:16].
Sets value for N2 low-speed divider, which drives phase detector.
00000000000000000001 = 2
00000000000000000011 = 4
00000000000000000101 = 6
...
11111111111111111111 = 2^20
Valid divider values = [2, 4, 6, ..., 2^20]
42
Rev. 1.0
D0
Si5326
Register 41.
Bit
D7
D6
D5
D4
D3
Name
N2_LS [15:8]
Type
R/W
D2
D1
D0
D1
D0
Reset value = 0000 0000
Bit
7:0
Name
Function
N2_LS [15:8] N2_LS [15:8].
Sets value for N2 low-speed divider, which drives phase detector.
00000000000000000001 = 2
00000000000000000011 = 4
00000000000000000101 = 6
...
11111111111111111111 = 2^20
Valid divider values = [2, 4, 6, ..., 2^20]
Register 42.
Bit
D7
D6
D5
D4
D3
Name
N2_LS [7:0]
Type
R/W
D2
Reset value = 1111 1001
Bit
Name
7:0
N2_LS [7:0]
Function
N2_LS [7:0].
Sets value for N2 low-speed divider, which drives phase detector.
00000000000000000001 = 2
00000000000000000011 = 4
00000000000000000101 = 6
...
11111111111111111111 = 2^20
Valid divider values = [2, 4, 6, ..., 2^20]
Rev. 1.0
43
Si5326
Register 43.
Bit
D7
D6
D5
D4
D3
D2
D1
Name
Reserved
N31 [18:16]
Type
R
R/W
D0
Reset value = 0000 0000
Bit
Name
7:3
Reserved
2:0
N31 [18:16]
Function
Reserved.
N31 [18:16].
Sets value for input divider for CKIN1.
0000000000000000000 = 1
0000000000000000001 = 2
0000000000000000010 = 3
...
1111111111111111111 = 2^19
Valid divider values=[1, 2, 3, ..., 2^19]
Register 44.
Bit
D7
D6
D5
D4
D3
Name
N31_[15:8]
Type
R/W
Reset value = 0000 0000
Bit
Name
7:0
N31_[15:8]
Function
N31_[15:8].
Sets value for input divider for CKIN1.
0000000000000000000 = 1
0000000000000000001 = 2
0000000000000000010 = 3
...
1111111111111111111 = 2^19
Valid divider values=[1, 2, 3, ..., 2^19]
44
Rev. 1.0
D2
D1
D0
Si5326
Register 45.
Bit
D7
D6
D5
D4
D3
Name
N31_[7:0]
Type
R/W
D2
D1
D0
D2
D1
D0
Reset value = 0000 1001
Bit
Name
7:0
N31_[7:0
Function
N31_[7:0].
Sets value for input divider for CKIN1.
0000000000000000000 = 1
0000000000000000001 = 2
0000000000000000010 = 3
...
1111111111111111111 = 2^19
Valid divider values=[1, 2, 3, ..., 2^19]
Register 46.
Bit
D7
D6
D5
D4
D3
Name
Reserved
N32_[18:16]
Type
R
R/W
Reset value = 0000 0000
Bit
Name
7:3
Reserved
2:0
N32_[18:16]
Function
Reserved.
N32_[18:16].
Sets value for input divider for CKIN2.
0000000000000000000 = 1
0000000000000000001 = 2
0000000000000000010 = 3
...
1111111111111111111 = 2^19
Valid divider values=[1, 2, 3, ..., 2^19]
Rev. 1.0
45
Si5326
Register 47.
Bit
D7
D6
D5
D4
D3
Name
N32_[15:8]
Type
R/W
D2
D1
D0
D2
D1
D0
Reset value = 0000 0000
Bit
Name
7:0
N32_[15:8]
Function
N32_[15:8].
Sets value for input divider for CKIN2.
0000000000000000000 = 1
0000000000000000001 = 2
0000000000000000010 = 3
...
1111111111111111111 = 2^19
Valid divider values=[1, 2, 3, ..., 2^19]
Register 48.
Bit
D7
D6
D5
D4
D3
N32_[7:0]
Name
R/W
Type
Reset value = 0000 1001
46
Bit
Name
7:0
N32_[7:0]
Function
N32_[7:0].
Sets value for input divider for CKIN1.
0000000000000000000 = 1
0000000000000000001 = 2
0000000000000000010 = 3
...
1111111111111111111 = 2^19
Valid divider values=[1, 2, 3, ..., 2^19]
Rev. 1.0
Si5326
Register 55.
Bit
D7
D6
D5
D4
D3
D2
D1
Name
Reserved
CLKIN2RATE_[2:0]
CLKIN1RATE[2:0]
Type
R
R/W
R/W
D0
Reset value = 0000 0000
Bit
Name
7:6
Reserved
Function
Reserved.
5:3
CLKIN2RATE CLKIN2RATE[2:0].
[2:0]
CKINn frequency selection for FOS alarm monitoring.
000: 10 - 27 MHz
001: 25 - 54 MHz
010: 50 - 105 MHz
011: 95 - 215 MHz
100: 190 - 435 MHz
101: 375 - 710 MHz
110: Reserved
111: Reserved
2:0
CLKIN1RATE CLKIN1RATE[2:0].
[2:0]
CKINn frequency selection for FOS alarm monitoring.
000: 10 - 27 MHz
001: 25 - 54 MHz
010: 50 - 105 MHz
011: 95 - 215 MHz
100: 190 - 435 MHz
101: 375 - 710 MHz
110: Reserved
111: Reserved
Rev. 1.0
47
Si5326
Register 128.
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
Reserved
CK2_ACTV_REG
CK1_ACTV_REG
Type
R
R
R
Reset value = 0010 0000
48
Bit
Name
7:2
Reserved
Function
Reserved.
1
CK2_ACTV_ CK2_ACTV_REG.
REG
Indicates if CKIN2 is currently the active clock for the PLL input.
0: CKIN2 is not the active input clock. Either it is not selected or LOS2_INT is 1.
1: CKIN2 is the active input clock.
0
CK1_ACTV_ CK1_ACTV_REG.
REG
Indicates if CKIN1 is currently the active clock for the PLL input.
0: CKIN1 is not the active input clock. Either it is not selected or LOS1_INT is 1.
1: CKIN1 is the active input clock.
Rev. 1.0
Si5326
Register 129.
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
Reserved
LOS2_INT
LOS1_INT
LOSX_INT
Type
R
R
R
R
Reset value = 0000 0110
Bit
Name
Function
7:3
Reserved
Reserved.
2
LOS2_INT
LOS2_INT.
Indicates the LOS status on CKIN2.
0: Normal operation.
1: Internal loss-of-signal alarm on CKIN2 input.
1
LOS1_INT
LOS1_INT.
Indicates the LOS status on CKIN1.
0: Normal operation.
1: Internal loss-of-signal alarm on CKIN1 input.
0
LOSX_INT
LOSX_INT.
Indicates the LOS status of the external reference on the XA/XB pins.
0: Normal operation.
1: Internal loss-of-signal alarm on XA/XB reference clock input.
Rev. 1.0
49
Si5326
Register 130.
Bit
D7
D6
D5
Name CLATPROG- DIGHOLDRESS
VALID
Type
R
D4
D2
D1
D0
Reserved
FOS2_INT
FOS1_INT
LOL_INT
R
R
R
R
R
D3
Reset value = 0000 0001
Bit
7
6
Name
Function
CLATPROG- CLAT Progress.
RESS
Indicates if the last change in the CLAT register has been processed.
0: Coarse skew adjustment not in progress.
1: Coarse skew adjustment in progress.
DIGHOLDVALID
Digital Hold Valid.
Indicates if the digital hold circuit has enough samples of a valid clock to meet digital hold
specifications.
0: Indicates digital hold history registers have not been filled. The digital hold output
frequency may not meet specifications.
1: Indicates digital hold history registers have been filled. The digital hold output
frequency is valid.
5:3
Reserved
Reserved.
2
FOS2_INT
CKIN2 Frequency Offset Status.
0: Normal operation.
1: Internal frequency offset alarm on CKIN2 input.
1
FOS1_INT
CKIN1 Frequency Offset Status.
0: Normal operation.
1: Internal frequency offset alarm on CKIN1 input.
0
LOL_INT
PLL Loss of Lock Status.
0: PLL locked.
1: PLL unlocked.
50
Rev. 1.0
Si5326
Register 131.
Bit
D7
D6
D5
Name
Reserved
Type
R
D4
D3
D2
D1
D0
LOS2_FLG LOS1_FLG LOSX_FLG
R/W
R/W
R/W
Reset value = 0001 1111
Bit
Name
7:3
Reserved
2
LOS2_FLG
Function
Reserved.
CKIN2 Loss-of-Signal Flag.
0: Normal operation.
1: Held version of LOS2_INT. Generates active output interrupt if output interrupt pin is
enabled (INT_PIN = 1) and if not masked by LOS2_MSK bit. Flag cleared by writing 0 to
this bit.
1
LOS1_FLG
CKIN1 Loss-of-Signal Flag.
0: Normal operation
1: Held version of LOS1_INT. Generates active output interrupt if output interrupt pin is
enabled (INT_PIN = 1) and if not masked by LOS1_MSK bit. Flag cleared by writing 0 to
this bit.
0
LOSX_FLG
External Reference (signal on pins XA/XB) Loss-of-Signal Flag.
0: Normal operation
1: Held version of LOSX_INT. Generates active output interrupt if output interrupt pin is
enabled (INT_PIN = 1) and if not masked by LOSX_MSK bit. Flag cleared by writing 0 to
this bit.
Rev. 1.0
51
Si5326
Register 132.
Bit
D7
D6
D5
Name
Reserved
Type
R
D4
D3
D2
FOS2_FLG FOS1_FLG
R/W
R/W
D1
D0
LOL_FLG
Reserved
R/W
R
Reset value = 0000 0010
Bit
Name
7:4
Reserved
3
FOS2_FLG
Function
Reserved.
CLKIN_2 Frequency Offset Flag.
0: Normal operation.
1: Held version of FOS2_INT. Generates active output interrupt if output interrupt pin is
enabled (INT_PIN = 1) and if not masked by FOS2_MSK bit. Flag cleared by writing 0 to
this bit.
2
FOS1_FLG
CLKIN_1 Frequency Offset Flag.
0: Normal operation
1: Held version of FOS1_INT. Generates active output interrupt if output interrupt pin is
enabled (INT_PIN = 1) and if not masked by FOS1_MSK bit. Flag cleared by writing 0 to
this bit.
1
LOL_FLG
PLL Loss of Lock Flag.
0: PLL locked
1: Held version of LOL_INT. Generates active output interrupt if output interrupt pin is
enabled (INT_PIN = 1) and if not masked by LOL_MSK bit. Flag cleared by writing 0 to
this bit.
0
52
Reserved
Reserved.
Rev. 1.0
Si5326
Register 134.
Bit
D7
D6
D5
D4
D3
Name
PARTNUM_RO [11:4]
Type
R
D2
D1
D0
D2
D1
D0
Reset value = 0000 0001
Bit
Name
7:0
PARTNUM_
RO [11:0]
Function
Device ID (1 of 2).
0000 0001 1010: Si5326
Register 135.
Bit
D7
D6
D5
D4
D3
Name
PARTNUM_RO [3:0]
REVID_RO [3:0]
Type
R
R
Reset value = 1010 0010
Bit
Name
7:4
PARTNUM_
RO [11:0]
Device ID (2 of 2).
REVID_RO
[3:0]
Device Revision.
3:0
Function
0000 0001 1010: Si5326
0000: Revision A
0001: Revision B
0010: Revision C
Others: Reserved
Rev. 1.0
53
Si5326
Register 136.
Bit
D7
D6
D5
D4
D3
D2
Name
RST_REG
ICAL
Reserved
Type
R/W
R/W
R
D1
D0
Reset value = 0000 0000
Bit
Name
7
RST_REG
Function
Internal Reset (Same as Pin Reset).
Note: The I2C (or SPI) port may not be accessed until 10 ms after RST_REG is asserted.
0: Normal operation.
1: Reset of all internal logic. Outputs disabled or tristated during reset.
6
ICAL
Start an Internal Calibration Sequence.
For proper operation, the device must go through an internal calibration sequence. ICAL
is a self-clearing bit. Writing a “1” to this location initiates an ICAL. The calibration is complete once the LOL alarm goes low.
0: Normal operation.
1: Writing a "1" initiates internal self-calibration. Upon completion of internal self-calibration, LOL will go low.
Notes:
1. A valid stable clock (within 100 ppm) must be present to begin ICAL.
2. If the input changes by more than 500 ppm, the part may do an autonomous ICAL.
3. See Table 9, “Register Locations Requiring ICAL,” on page 63 for register changes that
require an ICAL.
5:0
54
Reserved
Reserved.
Rev. 1.0
Si5326
Register 138.
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
Reserved
LOS2_EN
[1:1]
LOS1_EN
[1:1]
Type
R
R/W
R/W
Reset value = 0000 1111
Bit
Name
7:2
Reserved
Reserved.
1
LOS2_EN
[1:0]
Enable CKIN2 LOS Monitoring on the Specified Input (2 of 2).
LOS1_EN
[1:0]
Enable CKIN1 LOS Monitoring on the Specified Input (1 of 2).
0
Function
Note: LOS2_EN is split between two registers.
00: Disable LOS monitoring
01: Reserved
10: Enable LOSA monitoring
11: Enable LOS monitoring
LOSA is a slower and less sensitive version of LOS. SEe the Si53xx Family Reference
Manual for details.
Note: LOS1_EN is split between two registers.
00: Disable LOS monitoring
01: Reserved
10: Enable LOSA monitoring
11: Enable LOS monitoring
LOSA is a slower and less sensitive version of LOS. See the Si53xx Family Reference
Manual for details.
Rev. 1.0
55
Si5326
Register 139.
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
Reserved
LOS2_EN
[0:0]
LOS1_EN
[0:0]
Reserved
FOS2_EN
FOS1_EN
Type
R
R/W
R/W
R
R/W
R/W
Reset value = 1111 1111
Bit
Name
Function
7:6
Reserved
Reserved.
5
LOS2_EN
[1:0]
Enable CKIN2 LOS Monitoring on the Specified Input (2 of 2).
Note: LOS2_EN is split between two registers.
00: Disable LOS monitoring
01: Reserved
10: Enable LOSA monitoring
11: Enable LOS monitoring
LOSA is a slower and less sensitive version of LOS. See the Si53xx Family Reference
Manual for details
4
LOS1_EN
[1:0]
Enable CKIN1 LOS Monitoring on the Specified Input (1 of 2).
Note: LOS1_EN is split between two registers.
00: Disable LOS monitoring
01: Reserved
10: Enable LOSA monitoring
11: Enable LOS monitoring
LOSA is a slower and less sensitive version of LOS. See the Si53xx Family Reference
Manual for details.
3:2
Reserved
Reserved.
1
FOS2_EN
Enables FOS on a Per Channel Basis.
0: Disable FOS monitoring
1: Enable FOS monitoring
0
FOS1_EN
Enables FOS on a Per Channel Basis.
0: Disable FOS monitoring
1: Enable FOS monitoring
56
Rev. 1.0
Si5326
Register 142.
Bit
D7
D6
D5
D4
D3
Name
INDEPENDENTSKEW1 [7:0]
Type
R/W
D2
D1
D0
Reset value = 0000 0000
Bit
Name
7:0
INDEPENDENTSKEW1
[7:0]
Function
INDEPENDENTSKEW1.
Eight-bit field that represents a 2’s complement of the phase offset in terms of clocks from
the high speed output divider.
Register 143.
Bit
D7
D6
D5
D4
D3
Name
INDEPENDENTSKEW2 [7:0]
Type
R/W
D2
D1
D0
Reset value = 0000 0000
Bit
Name
7:0
INDEPENDENTSKEW2
[7:0]
Function
INDEPENDENTSKEW2.
Eight-bit field that represents a 2’s complement of the phase offset in terms of clocks from
the high speed output divider.
Rev. 1.0
57
Si5326
CKOUT1+
CKOUT1–
NC
GND
NC
VDD
CKOUT2–
CKOUT2+
CMODE
7. Pin Descriptions: Si5326
36 35 34 33 32 31 30 29 28
RST
1
27 SDI
NC
2
26 A2_SS
INT_C1B
3
25 A1
C2B
4
VDD
5
XA
6
XB
7
24 A0
GND
Pad
23 SDA_SDO
22 SCL
21 CS_CA
GND
8
20 INC
NC
9
19 DEC
LOL
CKIN1–
RATE1
CKIN1+
NC
CKIN2–
CKIN2+
VDD
RATE0
10 11 12 13 14 15 16 17 18
Pin #
Pin Name
I/O
Signal Level
Description
1
RST
I
LVCMOS
External Reset.
Active low input that performs external hardware reset of device.
Resets all internal logic to a known state and forces the device registers to their default value. Clock outputs are tristated during reset.
The part must be programmed after a reset or power on to get a
clock output. See the Si53xx Family Reference Manual for details.
This pin has a weak pull-up.
2, 9, 14,
30, 33
NC
—
—
No Connection.
Leave floating. Make no external connections to this pin for normal
operation.
3
INT_C1B
O
LVCMOS
Interrupt/CKIN1 Invalid Indicator.
This pin functions as a device interrupt output or an alarm output for
CKIN1. If used as an interrupt output, INT_PIN must be set to 1. The
pin functions as a maskable interrupt output with active polarity controlled by the INT_POL register bit.
If used as an alarm output, the pin functions as a LOS (and optionally FOS) alarm indicator for CKIN1. Set CK1_BAD_PIN = 1 and
INT_PIN = 0.
0 = CKIN1 present
1 = LOS (FOS) on CKIN1
The active polarity is controlled by CK_BAD_POL. If no function is
selected, the pin tristates.
Note: Internal register names are indicated by underlined italics, e.g., INT_PIN. See Section “5.Register Map”.
58
Rev. 1.0
Si5326
Pin #
Pin Name
I/O
Signal Level
Description
4
C2B
O
LVCMOS
CKIN2 Invalid Indicator.
This pin functions as a LOS (and optionally FOS) alarm indicator for
CKIN2 if CK2_BAD_PIN = 1.
0 = CKIN2 present
1 = LOS (FOS) on CKIN2
The active polarity can be changed by CK_BAD_POL. If
CK2_BAD_PIN = 0, the pin tristates.
5, 10, 32
VDD
VDD
Supply
Supply.
The device operates from a 1.8, 2.5, or 3.3 V supply. Bypass capacitors should be associated with the following VDD pins:
5
0.1 µF
10
0.1 µF
32
0.1 µF
A 1.0 µF should also be placed as close to the device as is practical.
7
6
XB
XA
I
Analog
External Crystal or Reference Clock.
External crystal should be connected to these pins to use internal
oscillator based reference. Refer to the Si53xx Family Reference
Manual for interfacing to an external reference. External reference
must be from a high-quality clock source (TCXO, OCXO). Frequency of crystal or external clock is set by RATE[1:0] pins.
8, 31
GND
GND
Supply
Ground.
Must be connected to system ground. Minimize the ground path
impedance for optimal performance of this device. Grounding these
pins does not eliminate the requirement to ground the GND PAD on
the bottom of the package.
11
15
RATE0
RATE1
I
3-Level
External Crystal or Reference Clock Rate.
Three level inputs that select the type and rate of external crystal or
reference clock to be applied to the XA/XB port. Refer to the Si53xx
Family Reference Manual for settings. These pins have both a weak
pull-up and a weak pull-down; they default to M.
L setting corresponds to ground.
M setting corresponds to VDD/2.
H setting corresponds to VDD.
Note: Tying the corresponding Raten pins to HH (VDD) provides
compatibility to Si5325. Refer to Si5325 data sheet for
operating in this mode.
Some designs may require an external resistor voltage divider when
driven by an active device that will tristate.
16
17
CKIN1+
CKIN1–
I
Multi
Clock Input 1.
Differential input clock. This input can also be driven with a singleended signal. Input frequency range is 2 kHz to 710 MHz.
12
13
CKIN2+
CKIN2–
I
Multi
Clock Input 2.
Differential input clock. This input can also be driven with a singleended signal. Input frequency range is 2 kHz to 710 MHz.
Note: Internal register names are indicated by underlined italics, e.g., INT_PIN. See Section “5.Register Map”.
Rev. 1.0
59
Si5326
Pin #
Pin Name
I/O
Signal Level
Description
18
LOL
O
LVCMOS
PLL Loss of Lock Indicator.
This pin functions as the active high PLL loss of lock indicator if the
LOL_PIN register bit is set to 1.
0 = PLL locked
1 = PLL unlocked
If LOL_PIN = 0, this pin will tristate. Active polarity is controlled by
the LOL_POL bit. The PLL lock status will always be reflected in the
LOL_INT read only register bit.
19
DEC
I
LVCMOS
Skew Decrement.
A pulse on this pin decreases the input to output device skew by
1/fOSC (approximately 200 ps). There is no limit on the range of
skew adjustment by this method.
Pin control is enabled by setting INCDEC_PIN = 1. If
INCDEC_PIN = 0, this pin is ignored and output skew is controlled
via the CLAT register.
If both INC and DEC are tied high, phase buildout is disabled and
the device maintains a fixed-phase relationship between the
selected input clock and the output clock during an input clock
switch.
See the Si53xx Family Reference Manual for more details.
This pin has a weak pull-down.
20
INC
I
LVCMOS
Skew Increment.
A pulse on this pin increases the input to output device skew by
1/fOSC (approximately 200 ps). There is no limit on the range of
skew adjustment by this method.
Pin control is enabled by setting INCDEC_PIN = 1. If
INCDEC_PIN = 0, this pin is ignored and output skew is controlled
via the CLAT register.
If both INC and DEC are tied high, phase buildout is disabled and
the device maintains a fixed-phase relationship between the
selected input clock and the output clock during an input clock
switch.
See the Si53xx Family Reference Manual for more details.
Note: INC does not increase skew if NI_HS = 4.
This pin has a weak pull-down.
Note: Internal register names are indicated by underlined italics, e.g., INT_PIN. See Section “5.Register Map”.
60
Rev. 1.0
Si5326
Pin #
Pin Name
I/O
Signal Level
Description
21
CS_CA
I/O
LVCMOS
Input Clock Select/Active Clock Indicator.
Input: In manual clock selection mode, this pin functions as the
manual input clock selector if the CKSEL_PIN is set to 1.
0 = Select CKIN1
1 = Select CKIN2
If CKSEL_PIN = 0, the CKSEL_REG register bit controls this function and this input tristates. If configured for input, must be tied high
or low.
Output: In automatic clock selection mode, this pin indicates which
of the two input clocks is currently the active clock. If alarms exist on
both clocks, CK_ACTV will indicate the last active clock that was
used before entering the digital hold state. The CK_ACTV_PIN register bit must be set to 1 to reflect the active clock status to the
CK_ACTV output pin.
0 = CKIN1 active input clock
1 = CKIN2 active input clock
If CK_ACTV_PIN = 0, this pin will tristate. The CK_ACTV status will
always be reflected in the CK_ACTV_REG read only register bit.
22
SCL
I
LVCMOS
Serial Clock.
This pin functions as the serial clock input for both SPI and I2C
modes.
This pin has a weak pull-down.
23
SDA_SDO
I/O
LVCMOS
Serial Data.
In I2C control mode (CMODE = 0), this pin functions as the bidirectional serial data port.
In SPI control mode (CMODE = 1), this pin functions as the serial
data output.
25
24
A1
A0
I
LVCMOS
Serial Port Address.
In I2C control mode (CMODE = 0), these pins function as hardware
controlled address bits. The I2C address is 1101 [A2] [A1] [A0].
In SPI control mode (CMODE = 1), these pins are ignored.
These pins have a weak pull-down.
26
A2_SS
I
LVCMOS
Serial Port Address/Slave Select.
In I2C control mode (CMODE = 0), this pin functions as a hardware
controlled address bit [A2].
In SPI control mode (CMODE = 1), this pin functions as the slave
select input.
This pin has a weak pull-down.
27
SDI
I
LVCMOS
Serial Data In.
In I2C control mode (CMODE = 0), this pin is ignored.
In SPI control mode (CMODE = 1), this pin functions as the serial
data input.
This pin has a weak pull-down.
Note: Internal register names are indicated by underlined italics, e.g., INT_PIN. See Section “5.Register Map”.
Rev. 1.0
61
Si5326
Pin #
Pin Name
I/O
Signal Level
Description
29
28
CKOUT1–
CKOUT1+
O
Multi
Output Clock 1.
Differential output clock with a frequency range of 2 kHz to 1.4 GHz.
Output signal format is selected by SFOUT1_REG register bits. Output is differential for LVPECL, LVDS, and CML compatible modes.
For CMOS format, both output pins drive identical single-ended
clock outputs.
34
35
CKOUT2–
CKOUT2+
O
Multi
Output Clock 2.
Differential output clock with a frequency range of 2 kHz to 1.4 GHz.
Output signal format is selected by SFOUT2_REG register bits. Output is differential for LVPECL, LVDS, and CML compatible modes.
For CMOS format, both output pins drive identical single-ended
clock outputs.
36
CMODE
I
LVCMOS
GND PAD
GND
GND
Supply
Control Mode.
Selects I2C or SPI control mode for the Si5326.
0 = I2C Control Mode
1 = SPI Control Mode
This pin must not be NC. Tie either high or low.
See the Si53xx Family Reference Manual for details on I2C or SPI
operation.
Ground Pad.
The ground pad must provide a low thermal and electrical
impedance to a ground plane.
Note: Internal register names are indicated by underlined italics, e.g., INT_PIN. See Section “5.Register Map”.
62
Rev. 1.0
Si5326
Table 9 lists all of the register locations that should be followed by an ICAL after their contents are changed.
Table 9. Register Locations Requiring ICAL
Addr
Register
0
BYPASS_REG
0
CKOUT_ALWAYS_ON
1
CK_PRIOR2
1
CK_PRIOR1
2
BWSEL_REG
4
HIST_DEL
5
ICMOS
7
FOSREFSEL
9
HIST_AVG
10
DSBL2_REG
10
DSBL1_REG
11
PD_CK2
11
PD_CK1
19
FOS_EN
19
FOS_THR
19
VALTIME
19
LOCKT
21
INCDEC_PIN
25
N1_HS
31
NC1_LS
34
NC2_LS
40
N2_HS
40
N2_LS
43
N31
46
N32
55
CLKIN2RATE
55
CLKIN1RATE
Rev. 1.0
63
Si5326
Table 10. Si5326 Pull up/Pull down
64
Pin #
Si5326
Pull up/
Pull down
1
RST
U
11
RATE0
U, D
15
RATE1
U, D
19
DEC
D
20
INC
D
21
CS_CA
U, D
22
SCL
D
24
A0
D
25
A1
D
26
A2_SS
D
27
SDI
D
36
CMODE
U, D
Rev. 1.0
Si5326
8. Ordering Guide
Ordering Part
Number
Output Clock Frequency
Range
Package
ROHS6,
Pb-Free
Temperature Range
Si5326A-C-GM
2 kHz–945 MHz
970–1134 MHz
1.213–1.4 GHz
36-Lead 6 x 6 mm QFN
Yes
–40 to 85 °C
Si5326B-C-GM
2 kHz–808 MHz
36-Lead 6 x 6 mm QFN
Yes
–40 to 85 °C
Si5326C-C-GM
2 kHz–346 MHz
36-Lead 6 x 6 mm QFN
Yes
–40 to 85 °C
Si5325/26-EVB
Evaluation Board
Note: Add an R at the end of the device to denote tape and reel options.
Rev. 1.0
65
Si5326
9. Package Outline: 36-Pin QFN
Figure 7 illustrates the package details for the Si5326. Table 11 lists the values for the dimensions shown in the
illustration.
Figure 7. 36-Pin Quad Flat No-lead (QFN)
Table 11. Package Dimensions
Symbol
Millimeters
Symbol
Millimeters
Min
Nom
Max
A
0.80
0.85
0.90
A1
0.00
0.02
0.05

—
—
12º
b
0.18
0.25
0.30
aaa
—
—
0.10
bbb
—
—
0.10
ccc
—
—
0.08
D
D2
L
6.00 BSC
3.95
4.10
4.25
Min
Nom
Max
0.50
0.60
0.70
e
0.50 BSC
ddd
—
—
0.10
E
6.00 BSC
eee
—
—
0.05
E2
3.95
4.10
4.25
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to JEDEC outline MO-220, variation VJJD.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for Small Body
Components.
66
Rev. 1.0
Si5326
10. Recommended PCB Layout
Figure 8. PCB Land Pattern Diagram
Figure 9. Ground Pad Recommended Layout
Rev. 1.0
67
Si5326
Table 12. PCB Land Pattern Dimensions
Dimension
MIN
MAX
e
0.50 BSC.
E
5.42 REF.
D
5.42 REF.
E2
4.00
4.20
D2
4.00
4.20
GE
4.53
—
GD
4.53
—
X
—
0.28
Y
0.89 REF.
ZE
—
6.31
ZD
—
6.31
Notes (General):
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing is per the ANSI Y14.5M-1994 specification.
3. This Land Pattern Design is based on IPC-SM-782 guidelines.
4. All dimensions shown are at Maximum Material Condition (MMC). Least Material
Condition (LMC) is calculated based on a Fabrication Allowance of 0.05 mm.
Notes (Solder Mask Design):
1. All metal pads are to be non-solder mask defined (NSMD). Clearance between the
solder mask and the metal pad is to be 60 µm minimum, all the way around the pad.
Notes (Stencil Design):
1. A stainless steel, laser-cut, and electro-polished stencil with trapezoidal walls should be
used to assure good solder paste release.
2. The stencil thickness should be 0.125 mm (5 mils).
3. The ratio of stencil aperture to land pad size should be 1:1 for the perimeter pads.
4. A 4 x 4 array of 0.80 mm square openings on 1.05 mm pitch should be used for the
center ground pad.
Notes (Card Assembly):
1. A No-Clean, Type-3 solder paste is recommended.
2. The recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification
for Small Body Components.
68
Rev. 1.0
Si5326
11. Si5326 Device Top Mark
Mark Method:
Laser
Font Size:
0.80 mm
Right-Justified
Line 1 Marking:
Si5326Q
Customer Part Number
Q = Speed Code: A, B, C
See Ordering Guide for options
Line 2 Marking:
C-GM
C = Product Revision
G = Temperature Range –40 to 85 °C (RoHS6)
M = QFN Package
Line 3 Marking:
YYWWRF
YY = Year
WW = Work Week
R = Die Revision
F = Internal code
Assigned by the Assembly House. Corresponds to the year
and work week of the mold date.
Line 4 Marking:
Pin 1 Identifier
Circle = 0.75 mm Diameter
Lower-Left Justified
XXXX
Internal Code
Rev. 1.0
69
Si5326
DOCUMENT CHANGE LIST
Revision 0.41 to Revision 0.42

Revision 0.1 to Revision 0.2
Updated LVTTL to LVCMOS is Table 2, “Absolute
Maximum Ratings,” on page 6.
 Added Figure 3, “Typical Phase Noise Plot,” on page
16.
 Updated Figure 4, “Si5326 Typical Application
Circuit (I2C Control Mode),” and Figure 5, “Si5326
Typical Application Circuit (SPI Control Mode),” on
page 17 to show preferred external reference
interface.
 Updated “5.Register Map”.

Added
RATE0 and changed RATE to RATE1 and
expanded RATE[1:0] description.
Changed font of register names to underlined italics.
Revision 0.42 to Revision 0.43
















Changed 1.8 V operating range to ±5%.
Updated Table 1 on page 4.
Updated Table 2 on page 6.
Updated Table 11 on page 66.
Added table under Figure 3 on page 16.
Updated "4. Functional Description" on page 18.
Clarified "5. Register Map" on page 20 including pullup/pull-down.





Revision 0.3 to Revision 0.4
Updated Table 1 on page 4.
 Added "11. Si5326 Device Top Mark" on page 69.

Revision 0.4 to Revision 0.41


Changed “latency” to “skew” throughout.
Updated Table 1 on page 4.
Updated
Thermal Resistance Junction to Ambient
typical specification.






70
Changed register address labels to decimal.
Revision 0.44 to Revision 1.0

Revision 0.2 to Revision 0.3
Replaced Figure 9.
Updated Rise/Fall time values.
Revision 0.43 to Revision 0.44

Updated "8. Ordering Guide" on page 65.
 Added "9. Package Outline: 36-Pin QFN" on page
66.
 Added “10.Recommended PCB Layout”.
Text added to section "5. Register Map" on page 20.
Updated Figure 4 on page 17.
Updated Figure 5, “Si5326 Typical Application
Circuit (SPI Control Mode),” on page 17.
Updated "5. Register Map" on page 20.
Updated "9. Package Outline: 36-Pin QFN" on page
66.
Added Figure 9, “Ground Pad Recommended
Layout,” on page 67
Added Register Map
Rev. 1.0
Updated first page format to add chip image and pin
out
Updated Functional Block Diagram
Updated Section “1.Electrical Specifications” to
include ac/dc specifications from the Si53xx Family
Reference Manual (FRM)
Updated typical phase noise performance in Section
“2.Typical Phase Noise Performance”
Added INC/DEC pins to Figure 4 and Figure 5
Clarified the format for FLAT [14:0]
Added list of weak pull up/down resistors in Table 10,
“Si5326 Pull up/Pull down,” on page 64
Updated register maps 19, 20, 46, 47, 55, 142, 143,
185
Added note to typical application circuits in Section
“3.Typical Application Circuit”
Added evaluation board part number to “8.Ordering
Guide”
Updated Section “11.Si5326 Device Top Mark”
Updated Table 5, “Jitter Generation,” on page 14;
filled in all TBDs, and lowered typical RMS values
Si5326
NOTES:
Rev. 1.0
71
ClockBuilder Pro
One-click access to Timing tools,
documentation, software, source
code libraries & more. Available for
Windows and iOS (CBGo only).
www.silabs.com/CBPro
Timing Portfolio
www.silabs.com/timing
SW/HW
Quality
Support and Community
www.silabs.com/CBPro
www.silabs.com/quality
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,
USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com