Download Datasheet

LIS344ALH
MEMS inertial sensor
high performance 3-axis ±2/±6g ultracompact linear accelerometer
Features
■
2.4 V to 3.6 V single supply operation
■
±2 g / ±6 g user selectable full-scale
■
Low power consumption
■
Output voltage, offset and sensitivity are
ratiometric to the supply voltage
■
Factory trimmed device sensitivity and offset
■
Embedded self test
■
RoHS/ECOPACK® compliant
■
High shock survivability ( 10000 g )
Description
The LIS344ALH is an ultra compact consumer
low-power three-axis linear accelerometer that
includes a sensing element and an IC interface
able to take the information from the sensing
element and to provide an analog signal to the
external world.
The sensing element, capable of detecting the
acceleration, is manufactured using a dedicated
process developed by ST to produce inertial
sensors and actuators in silicon.
The IC interface is manufactured using an ST
proprietary CMOS process with high level of
integration. The dedicated circuit is trimmed to
better match the sensing element characteristics.
Table 1.
LGA 16L (4x4x1.5 mm)
The LIS344ALH has a dynamically user
selectable full-scale of ±2 g / ±6 g and it is
capable of measuring accelerations over a
maximum bandwidth of 1.8 kHz for all axes. The
device bandwidth may be reduced by using
external capacitances. The self-test capability
allows the user to check the functioning of the
system.
The LIS344ALH is available in Land Grid Array
package (LGA) manufactured by ST.
It is guaranteed to operate over an extended
temperature range of -40 °C to +85 °C.
The LIS344ALH belongs to a family of products
suitable for a variety of applications:
– Mobile terminals
– Gaming and virtual reality input devices
– Antitheft systems and inertial navigation
– Appliance and robotics.
Device summary
Order codes
Temp range [° C]
Package
Packaging
LIS344ALH
-40 to +85
LGA-16L
Tray
LIS344ALHTR
-40 to +85
LGA-16L
Tape and reel
April 2008
Rev 3
1/19
www.st.com
19
Content
LIS344ALH
Content
1
2
3
4
5
Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Mechanical and electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1
Mechanical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.4
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1
Sensing element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2
IC interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.3
Factory calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Application hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1
Soldering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2
Output response vs orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.1
Mechanical characteristics at 25 °C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.2
Mechanical characteristics derived from measurement in the -40 °C to +85
°C temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.3
Electrical characteristics at 25 °C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/19
LIS344ALH
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
LIS344ALH electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Output response vs orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
X axis Zero-g level at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
X axis Sensitivity at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Y axis Zero-g level at 3.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Y axis Sensitivity at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Z axis Zero-g level at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Z axis Sensitivity at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
X axis Zero-g level change vs. temperature at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
X axis Sensitivity change vs. temperature at 3.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Y axis Zero-g level change vs. temperature at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Y axis Sensitivity change vs. temperature at 3.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Z axis Zero-g level change vs. temperature at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Z axis Sensitivity change vs. temperature at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Current consumption in normal mode at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Current consumption in power-down at 3.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Noise density at 3.3 V (X, Y axis) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Noise density at 3.3 V (Z axis) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
LGA 16: mechanical data and package dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3/19
List of tables
LIS344ALH
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
4/19
Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mechanical characteristics @ Vdd =3.3 V, T = 25 °C unless otherwise noted . . . . . . . . . . . 7
Electrical characteristics @ Vdd =3.3 V, T = 25 °C unless otherwise noted. . . . . . . . . . . . . 8
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Filter capacitor selection, Cload (x, y, z), . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
LIS344ALH
Block diagram and pin description
1
Block diagram and pin description
1.1
Block diagram
Figure 1.
Block diagram
X+
CHARGE
AMPLIFIER
Y+
Z+
a
MUX
Routx
VoutX
Routy
VoutY
Routz
VoutZ
S/H
DEMUX
S/H
ZYXS/H
REFERENCE
SELF TEST
1.2
TRIMMING CIRCUIT
CLOCK
Pin description
Figure 2.
Pin connection
NC
Res
Vdd
NC
Z
13
1
VoutX
16
1
12
NC
ST
VoutY
X
Y
NC
NC
9
4
8
Res
5
PD
NC
GND
VoutZ
(TOP VIEW)
DIRECTIONS OF THE
DETECTABLE
ACCELERATIONS
FS
(BOTTOM VIEW)
5/19
Block diagram and pin description
Table 2.
6/19
LIS344ALH
Pin description
Pin #
Pin name
Function
1
FS
Full scale selection (logic 0: ±2g full-scale; logic 1: ±6g full-scale)
2
ST
Self test (logic 0: normal mode; logic 1: self-test mode)
3
NC
Internally not connected
4
Res
Leave unconnected or connect to Vdd
5
PD
Power down (logic 0: normal mode; logic 1: power-down mode)
6
NC
Internally not connected
7
GND
0 V supply
8
VoutZ
Output voltage Z channel
9
NC
Internally not connected
10
VoutY
Output voltage Y channel
11
NC
Internally not connected
12
VoutX
Output voltage X channel
13
NC
Internally not connected
14
Vdd
Power supply
15
Res
Connect to Vdd
16
NC
Internally not connected
LIS344ALH
Mechanical and electrical specifications
2
Mechanical and electrical specifications
2.1
Mechanical characteristics
Table 3.
Mechanical characteristics @ Vdd =3.3 V, T = 25 °C unless otherwise noted(1)
Symbol
Ar
So
Parameter
Acceleration range(3)
Sensitivity(4)
Test condition
Min.
Typ.(2)
FS pin connected to
GND
±1.8
±2
FS pin connected to Vdd
±5.4
±6
Full-scale = ±2 g
Vdd/5 - 5%
Vdd/5
Vdd/5 + 5%
Full-scale = ±6 g
Vdd/15 - 10%
Vdd/15
Vdd/15 + 10%
Max.
Unit
g
V/g
SoDr
Sensitivity change Vs
Temperature
Delta from +25 °C
Voff
Zero-g level(4)
Full-scale = ±2 g
T = 25 °C
Zero-g level change Vs
Temperature
Delta from +25 °C
±0.4
mg/°C
Non linearity(5)
Best fit straight line
Full-scale = ±2 g
±0.5
% FS
±2
%
50
µg/ Hz
OffDr
NL
± 0.01
Vdd/2 - 5%
CrossAx Cross-axis(6)
An
Vt
Acceleration noise
density
Self test output voltage
change(7),(8),(9)
Fres
Sensing element
resonant frequency(10)
Top
Operating temperature
range
Wh
Product weight
Vdd = 3.3 V;
Full-scale = ±2 g
Vdd/2
%/°C
Vdd/2 + 5%
V
X axis
T = 25 °C; Vdd=3.3 V
80
140
200
mV
Y axis
T = 25 °C; Vdd=3.3 V
-200
-140
-80
mV
Z axis
T = 25 °C; Vdd=3.3 V
100
230
350
mV
X,Y,Z axis
1.8
KHz
-40
+85
0.040
°C
gram
1. The product is factory calibrated at 3.3 V. The operational power supply range is from 2.4 V to 3.6 V. Voff, So and Vt
parameters will vary with supply voltage.
2. Typical specifications are not guaranteed.
3. Guaranteed by wafer level test and measurement of initial offset and sensitivity.
4. Zero-g level and sensitivity are essentially ratiometric to supply voltage at the calibration level ±8%.
5. Guaranteed by design.
6. Contribution to the measuring output of an inclination/acceleration along any perpendicular axis.
7. “Self test output voltage change” is defined as Vout(Vst=Logic1)-Vout(Vst=Logic0).
8. “Self test output voltage change” varies cubically with supply voltage.
9. When full-scale is set to ±6 g, “Self test output voltage change” is one third of the specified value at ±2 g.
10. Minimum resonance frequency Fres=1.8 kHz. Sensor bandwidth=1/(2*π*110kΩ*Cload), with Cload>1 nF.
7/19
Mechanical and electrical specifications
LIS344ALH
2.2
Electrical characteristics
Table 4.
Electrical characteristics @ Vdd =3.3 V, T = 25 °C unless otherwise noted(1)
Symbol
Parameter
Vdd
Supply voltage
Idd
Supply current
Test condition
Min.
Typ.(2)
Max.
Unit
2.4
3.3
3.6
V
680
850
1
5
Normal mode
µA
Power-down mode
Logic 0 level
0
0.3*Vdd
V
Logic 1 level
0.7*Vdd
Vdd
V
130
KΩ
Vfs
Vst
Vpd
Full-scale input
Self-test input
Power-down input
Rout
Output impedance of
VoutX, VoutY, VoutZ
90
Cload
Capacitive load drive(3)
for VoutX, VoutY, VoutZ
1
Ton
Turn-on time at exit of
Power-down mode
Top
Operating temperature
range
110
nF
550*Cload+
0.3
Cload expressed in µF
-40
1. The product is factory calibrated at 3.3 V.
2. Typical specifications are not guaranteed.
3. Minimum resonance frequency Fres=1.8 kHz. Device bandwidth=1/(2*π*110 kΩ*Cload), with Cload>1 nF.
8/19
ms
+85
ºC
LIS344ALH
2.3
Mechanical and electrical specifications
Absolute maximum ratings
Stresses above those listed as “Absolute maximum ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Table 5.
Absolute maximum ratings
Symbol
Ratings
Vdd
Supply voltage
Vin
Input voltage on any control pin (FS, ST, PD)
APOW
Acceleration (any axis, powered, Vdd = 3.3 V)
AUNP
Acceleration (any axis, not powered)
TSTG
Storage temperature range
Maximum value
Unit
-0.3 to 7
V
-0.3 to Vdd +0.3
V
3000 g for 0.5 ms
10000 g for 0.1 ms
3000 g for 0.5 ms
ESD
10000 g for 0.1 ms
Electrostatic discharge protection
-40 to +125
°C
4 (HBM)
KV
1.5 (CDM)
KV
400 (MM)
V
This is a mechanical shock sensitive device, improper handling can cause permanent
damages to the part
This is an ESD sensitive device, improper handling can cause permanent damages to
the part
9/19
Mechanical and electrical specifications
2.4
LIS344ALH
Terminology
Sensitivity describes the gain of the sensor and can be determined by applying 1g
acceleration to it. As the sensor can measure DC accelerations this can be done easily by
pointing the axis of interest towards the center of the Earth, note the output value, rotate the
sensor by 180 degrees (point to the sky) and note the output value again thus applying ±1g
acceleration to the sensor. Subtracting the larger output value from the smaller one, and
dividing the result by 2, will give the actual sensitivity of the sensor. This value changes very
little over temperature (see sensitivity change vs temperature) and also very little over time.
The Sensitivity tolerance describes the range of sensitivities of a large population of
sensors.
Zero-g level describes the actual output signal if there is no acceleration present. A sensor
in a steady state on a horizontal surface will measure 0 g in X axis and 0 g in Y axis whereas
the Z axis will measure 1g. The output is ideally for a 3.3 V powered sensor Vdd/2 = 1650
mV. A deviation from ideal 0-g level (1650 mV in this case) is called Zero-g offset. Offset of
precise MEMS sensors is to some extend a result of stress to the sensor and therefore the
offset can slightly change after mounting the sensor onto a printed circuit board or exposing
it to extensive mechanical stress. Offset changes little over temperature - see “Zero-g level
change vs temperature” - the Zero-g level of an individual sensor is very stable over lifetime.
The Zero-g level tolerance describes the range of Zero-g levels of a population of sensors.
Self test allows to test the mechanical and electric part of the sensor, allowing the seismic
mass to be moved by means of an electrostatic test-force. The Self Test function is off when
the ST pin is connected to GND. When the ST pin is tied at Vdd an actuation force is applied
to the sensor, simulating a definite input acceleration. In this case the sensor outputs will
exhibit a voltage change in their DC levels which is related to the selected full-scale and
depending on the supply voltage through the device sensitivity. When ST is activated, the
device output level is given by the algebraic sum of the signals produced by the acceleration
acting on the sensor and by the electrostatic test-force. If the output signals change within
the amplitude specified inside Table 3, then the sensor is working properly and the
parameters of the interface chip are within the defined specification.
Output impedance describes the resistor inside the output stage of each channel. This
resistor is part of a filter consisting of an external capacitor of at least 1 nF and the internal
resistor. Due to the high resistor level, only small inexpensive external capacitors are
needed to generate low corner frequencies. When interfacing with an ADC it is important to
use high input impedance input circuitries to avoid measurement errors. Note that the
minimum load capacitance forms a corner frequency close to the resonance frequency of
the sensor. In general the smallest possible bandwidth for a particular application should be
chosen to get the best results.
10/19
LIS344ALH
3
Functionality
Functionality
The LIS344ALH is an ultra compact low-power, analog output three-axis linear
accelerometer packaged in a LGA package. The complete device includes a sensing
element and an IC interface able to take the information from the sensing element and to
provide an analog signal to the external world.
3.1
Sensing element
A proprietary process is used to create a surface micro-machined accelerometer. The
technology allows to carry out suspended silicon structures which are attached to the
substrate in a few points called anchors and are free to move in the direction of the sensed
acceleration. To be compatible with the traditional packaging techniques a cap is placed on
top of the sensing element to avoid blocking the moving parts during the moulding phase of
the plastic encapsulation.
When an acceleration is applied to the sensor the proof mass displaces from its nominal
position, causing an imbalance in the capacitive half-bridge. This imbalance is measured
using charge integration in response to a voltage pulse applied to the sense capacitor.
At steady state the nominal value of the capacitors are few pF and when an acceleration is
applied the maximum variation of the capacitive load is in the fF range.
3.2
IC interface
The complete signal processing uses a fully differential structure, while the final stage
converts the differential signal into a single-ended one to be compatible with the external
world.
The first stage is a low-noise capacitive amplifier that implements a Correlated Double
Sampling (CDS) at its output to cancel the offset and the 1/f noise. The produced signal is
then sent to three different S&Hs, one for each channel, and made available to the outside.
All the analog parameters (output offset voltage and sensitivity) are ratiometric to the
voltage supply. Increasing or decreasing the voltage supply, the sensitivity and the offset will
increase or decrease linearly. This feature provides the cancellation of the error related to
the voltage supply along an analog to digital conversion chain.
3.3
Factory calibration
The IC interface is factory calibrated for sensitivity (So) and Zero-g level (Voff).
The trimming values are stored inside the device by a non volatile structure. Any time the
device is turned on, the trimming parameters are downloaded into the registers to be
employed during the normal operation. This allows the user to employ the device without
further calibration.
11/19
Application hints
4
LIS344ALH
Application hints
Figure 3.
LIS344ALH electrical connection
GND
GND
100nF
FS
ST
16
15
14
Vdd
10µF
13
Z
Optional
12
1
2
LIS344ALH
11
3
(top view)
10
5
6
7
Pin 1 indicator
Cload X
Optional
9
4
1
Vout x
Y
Vout y
Cload Y
X
8
(TOP VIEW)
Optional
PD
Vout z
Cload Z
GND
DIRECTIONS OF THE
DETECTABLE
ACCELERATIONS
Digital signals
Power supply decoupling capacitors (100 nF ceramic or polyester + 10 µF Aluminum)
should be placed as near as possible to the device (common design practice).
The LIS344ALH allows to band limit VoutX, VoutY and VoutZ through the use of external
capacitors. The recommended frequency range spans from DC up to 1.8 kHz. In particular,
capacitors are added at output VoutX, VoutY, VoutZ pins to implement low-pass filtering for
antialiasing and noise reduction. The equation for the cut-off frequency (ft) of the external
filters is in this case:
1
f t = ------------------------------------------------------------------------2π ⋅ R out ⋅ C load ( x, y, z )
Taking into account that the internal filtering resistor (Rout) has a nominal value equal to
110 KΩ, the equation for the external filter cut-off frequency may be simplified as follows:
1.45µF
f t = --------------------------------------- [ Hz ]
C load ( x, y, z )
The tolerance of the internal resistor can vary typically of ±20% within its nominal value of
110 KΩ; thus the cut-off frequency will vary accordingly. A minimum capacitance of 1 nF for
Cload(x, y, z) is required.
12/19
LIS344ALH
Application hints
Table 6.
4.1
Filter capacitor selection, Cload (x, y, z),
Cut-off frequency
Capacitor value
1 Hz
1500 nF
10 Hz
150 nF
20 Hz
68 nF
50 Hz
30 nF
100 Hz
15 nF
200 Hz
6.8 nF
500 Hz
3 nF
Soldering information
The LGA package is compliant with the ECOPACK, RoHS and “Green” standard.
It is qualified for soldering heat resistance according to JEDEC J-STD-020C.
Leave “Pin 1 Indicator” unconnected during soldering.
Land pattern and soldering recommendations are available at www.st.com/mems.
4.2
Output response vs orientation
Figure 4.
Output response vs orientation
X=2.31V (+1g)
Y=1.65V (0g)
Z=1.65V (0g)
X=1.65V (0g)
Y=2.31V (+1g)
Z=1.65V (0g)
X=1.65V (0g)
Y=0.99V (-1g)
Z=1.65V (0g)
X=0.99V (-1g)
Y=1.65V (0g)
Z=1.65V (0g)
Bottom
Top
X=1.65V (0g)
Y=1.65V (0g)
Z=0.99V (-1g)
Top
X=1.65V (0g)
Y=1.65V (0g)
Bottom Z=2.31V (+1g)
Earth’s Surface
Figure 4 shows output voltage values of LIS344ALH, powered at 3.3 V, with full-scale ±2 g.
13/19
Typical performance characteristics
LIS344ALH
5
Typical performance characteristics
5.1
Mechanical characteristics at 25 °C
Figure 5.
X axis Zero-g level at 3.3 V
Figure 6.
30
X axis Sensitivity at 3.3 V
16
14
25
Percent of parts [%]
Percent of parts [%]
12
20
15
10
10
8
6
4
5
2
0
1.6
1.61
Figure 7.
1.62
1.63
1.64
1.65
1.66
Zero−g Level Offset [V]
1.67
1.68
1.69
0
0.62
1.7
Y axis Zero-g level at 3.3 V
Figure 8.
25
0.63
0.64
0.65
0.66
0.67
Sensitivity [V/g]
0.68
0.69
0.7
0.69
0.7
0.69
0.7
Y axis Sensitivity at 3.3 V
15
Percent of parts [%]
Percent of parts [%]
20
15
10
10
5
5
0
1.6
1.61
Figure 9.
1.62
1.63
1.64
1.65
1.66
Zero−g Level Offset [V]
1.67
1.68
1.69
0
0.62
1.7
Z axis Zero-g level at 3.3 V
0.63
0.64
0.65
0.66
0.67
Sensitivity [V/g]
0.68
Figure 10. Z axis Sensitivity at 3.3 V
25
14
12
20
Percent of parts [%]
Percent of parts [%]
10
15
10
8
6
4
5
2
0
1.6
14/19
1.61
1.62
1.63
1.64
1.65
1.66
Zero−g Level Offset [V]
1.67
1.68
1.69
1.7
0
0.62
0.63
0.64
0.65
0.66
0.67
Sensitivity [V/g]
0.68
LIS344ALH
5.2
Typical performance characteristics
Mechanical characteristics derived from measurement in the
-40 °C to +85 °C temperature range
Figure 11. X axis Zero-g level change
vs. temperature at 3.3 V
Figure 12. X axis Sensitivity change
vs. temperature at 3.3 V
40
60
35
50
Percent of parts [%]
Percent of parts [%]
30
25
20
15
40
30
20
10
10
5
0
−4
−3
−2
−1
0
1
o
Zero−g Level drift [mg/ C]
2
3
Figure 13. Y axis Zero-g level change
vs. temperature at 3.3 V
45
45
40
40
35
35
30
30
25
20
15
5
−1
0
1
o
Zero−g Level drift [mg/ C]
2
−0.02
0
0.02
o
Sensitivity drift [%/ C]
0.04
0.06
0.08
0.1
0.08
0.1
0.08
0.1
15
10
−2
−0.04
20
5
−3
−0.06
25
10
0
−4
−0.08
Figure 14. Y axis Sensitivity change
vs. temperature at 3.3 V
Percent of parts [%]
Percent of parts [%]
0
−0.1
4
3
0
−0.1
4
Figure 15. Z axis Zero-g level change
vs. temperature at 3.3 V
−0.08
−0.06
−0.04
−0.02
0
0.02
o
Sensitivity drift [%/ C]
0.04
0.06
Figure 16. Z axis Sensitivity change
vs. temperature at 3.3 V
35
40
35
30
30
Percent of parts [%]
Percent of parts [%]
25
20
15
25
20
15
10
10
5
0
−4
5
−3
−2
−1
0
1
Zero−g Level drift [mg/oC]
2
3
4
0
−0.1
−0.08
−0.06
−0.04
−0.02
0
0.02
Sensitivity drift [%/oC]
0.04
0.06
15/19
Typical performance characteristics
5.3
LIS344ALH
Electrical characteristics at 25 °C
Figure 17. Current consumption
in normal mode at 3.3 V
Figure 18.
30
Current consumption
in power-down at 3.3 V
45
40
25
20
Percent of parts [%]
Percent of parts [%]
35
15
10
30
25
20
15
10
5
5
0
450
500
550
600
650
700
750
Current consumption [uA]
800
850
0
−4
900
−3
−2
−1
0
1
Current consumption [uA]
2
3
4
30
30
25
25
20
20
15
15
10
10
5
5
0
18
16/19
Frequency of parts [%]
Frequency of parts [%]
Figure 19. Noise density at 3.3 V (X, Y axis) Figure 20. Noise density at 3.3 V (Z axis)
20
22
24
26
Noise Density [/mug/sqrt(Hz)]
28
30
32
0
10
20
30
40
50
Noise Density [/mug/sqrt(Hz)]
60
70
80
LIS344ALH
6
Package information
Package information
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a lead-free second level interconnect. The category of
second level Interconnect is marked on the inner box label, in compliance with JEDEC
Standard JESD97. The maximum ratings related to soldering conditions are also marked on
the inner box label. ECOPACK® is an ST trademark.
ECOPACK® specifications are available at: www.st.com.
Figure 21. LGA 16L: mechanical data and package dimensions
Dimensions
Ref.
mm
Min.
A1
1.500
A2
A3
0.160
d
inch
Typ. Max.
0.200
0.300
Min.
Typ.
Max.
1.600
0.0591 0.0630
1.330
0.0524
Outline and
mechanical data
0.240 0.0063 0.0079 0.0094
0.0118
D1
3.850
4.000
4.150 0.1516 0.1575 0.1634
E1
3.850
4.000
4.150 0.1516 0.1575 0.1634
L2
1.950
0.0768
M
0.100
0.0039
N1
0.650
0.0256
N2
0.975
0.0384
P1
1.750
0.0689
P2
1.525
0.0600
T1
0.400
0.0157
T2
0.300
0.0118
k
0.050
0.0020
LGA 16L (4x4x1.5mm)
Land Grid Array Package
7974136
17/19
Revision history
7
LIS344ALH
Revision history
Table 7.
18/19
Document revision history
Date
Revision
Changes
15-Jan-2008
1
Initial release.
18-Feb-2008
2
Minor text changes
29-Apr-2008
3
Updated Section 2: Mechanical and electrical specifications and
added distribution graphs in Section 5: Typical performance
characteristics
LIS344ALH
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
19/19