S i5 2111- B 5/ B6 PCI-E XPRESS G EN 3 S INGLE O UTPUT C LOCK G ENERATOR Features PCI-Express Gen 1, Gen 2, Gen 3, and Gen 4 common clock compliant Gen 3 SRNS Compliant Low power HCSL differential output buffer Supports Serial-ATA (SATA) at 100 MHz No termination resistors required 25 MHz Crystal Input or Clock input Triangular spread spectrum profile for maximum EMI reduction (Si52111-B6) Extended Temperature: –40 to 85 °C 3.3 V Power supply Small package 10-pin TDFN (3x3 mm) Si52111-B5 does not support spread spectrum outputs Si52111-B6 supports 0.5% down spread outputs Ordering Information: See page 13 Applications Network Attached Storage Multi-function Printer Wireless Access Point Routers Pin Assignments Description Si52111-B5/B6 is a high-performance, PCIe clock generator that can source one PCIe clock output from a 25 MHz crystal or clock input. The clock output is compliant to PCIe Gen 1, Gen 2, Gen 3, Gen 3 SRNS and Gen 4 common clock specifications. The ultra-small footprint (3x3 mm) and industry leading low power consumption make Si52111-B5/B6 the ideal clock solution for consumer and embedded applications. Measuring PCIe clock jitter is quick and easy with the Silicon Labs PCIe Clock Jitter Tool. Download it for free at www.silabs.com/pcie-learningcenter. Functional Block Diagram VDD 1 10 VDD XOUT 2 9 NC XIN/CLKIN 3 8 NC VSS 4 7 DIFF1 VSS 5 6 DIFF1 Patents pending VDD XIN/CLKIN PLL Divider DIFF1 XOUT VSS Rev 1.2 12/15 Copyright © 2015 by Silicon Laboratories Si52111-B5/B6 Si52111 -B5/B6 2 Rev 1.2 Si52111-B5/B6 TABLE O F C ONTENTS Section Page 1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Crystal Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.1. Crystal Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.2. Calculating Load Capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3. Test and Measurement Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.1. 10-Pin TDFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.2. 8-Pin TSSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6. Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6.1. TDFN Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6.2. TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 7. Recommended Design Guideline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Rev 1.2 3 Si52111 -B5/B6 1. Electrical Specifications Table 1. Recommended Operating Conditions Parameter Supply Voltage (extended) Supply Voltage (commercial) Symbol Test Condition Min Typ Max Unit VDD(extended) 3.3 V ± 5% 3.13 3.3 3.46 V VDD(commercial) 3.3 V ± 10% 2.97 3.3 3.63 V Table 2. DC Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Operating Voltage VDD 3.3 V ± 10% 2.97 3.30 3.63 V Operating Supply Current IDD Full Active — — 13 mA Input Pin Capacitance CIN Input Pin Capacitance — 3 5 pF COUT Output Pin Capacitance — — 5 pF Output Pin Capacitance Table 3. AC Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit LACC Measured at VDD/2 differential — — 250 ppm TDC Measured at VDD/2 45 — 55 % CLKIN Rise and Fall Times TR/TF Measured between 0.2 VDD and 0.8 VDD 0.5 — 4.0 V/ns CLKIN Cycle-to-Cycle Jitter TCCJ Measured at VDD/2 — — 250 ps CLKIN Long Term Jitter TLTJ Measured at VDD/2 — — 350 ps Input High Voltage VIH XIN/CLKIN pin 2 — VDD+0.3 V Input Low Voltage VIL XIN/CLKIN pin — — 0.8 V Input High Current IIH XIN/CLKIN pin, VIN = VDD — — 35 uA Input Low Current IIL XIN/CLKIN pin, 0 < VIN <0.8 –35 — — uA TDC Measured at 0 V differential 45 — 55 % TSKEW Measured at 0 V differential — — 60 ps Output Frequency FOUT VDD = 3.3 V — 100 — MHz Frequency Accuracy FACC All output clocks — — 100 ppm tr/f2 Measured differentially from ±150 mV 0.6 — 4.0 V/ns Crystal Long-term Accuracy Clock Input CLKIN Duty Cycle DIFF Clocks Duty Cycle Skew Slew Rate Notes: 1. Visit www.pcisig.com for complete PCIe specifications. 2. Gen 4 specifications based on the PCI-Express Base Specification 4.0 rev. 0.5 3. Download the Silicon Labs PCIe Clock Jitter Tool at www.silabs.com/pcie-learningcenter. 4 Rev 1.2 Si52111-B5/B6 Table 3. AC Electrical Specifications (Continued) Parameter Symbol Test Condition Min Typ Max Unit TCCJ Measured at 0 V differential — 28 70 ps PCIe Gen 1 Pk-Pk Jitter, Common Clock Pk-PkGEN1 PCIe Gen 1 — 24 86 ps PCIe Gen 2 Phase Jitter, Common Clock RMSGEN2 10 kHz < F < 1.5 MHz — 1.35 3.0 ps 1.5 MHz < F < Nyquist — 1.4 3.1 ps PCIe Gen 3 Phase Jitter, Common Clock RMSGEN3 Includes PLL BW 2–4 MHz, CDR = 10 MHz — 0.4 1.0 ps RMSGEN3_SRNS PLL BW of 2–4 or 2–5 MHz, CDR = 10 MHz — 0.28 0.71 ps RMSGEN4 PLL BW of 2–4 or 2–5 MHz, CDR = 10 MHz — 0.4 1.0 ps VOX 300 — 550 mV Voltage High VHIGH — — 1.15 V Voltage Low VLOW –0.3 — — V Spread Range SRNG Down Spread, -B6 only — –0.5 — % Modulation Frequency FMOD -B6 only 30 31.5 33 kHz Cycle-to-Cycle Jitter PCIe Gen 3 Phase Jitter, Separate Reference No Spread, SRNS PCIe Gen 4 Phase Jitter, Common Clock Crossing Point Voltage at 0.7 V Swing Enable/Disable and Set-up Clock Stabilization from Power-up TSTABLE — — 3 ms Stopclock Set-up Time TSS 10.0 — — ns Notes: 1. Visit www.pcisig.com for complete PCIe specifications. 2. Gen 4 specifications based on the PCI-Express Base Specification 4.0 rev. 0.5 3. Download the Silicon Labs PCIe Clock Jitter Tool at www.silabs.com/pcie-learningcenter. Rev 1.2 5 Si52111 -B5/B6 Table 4. Thermal Conditions Parameter Symbol Test Condition Min Typ Max Unit Temperature, Storage TS Non-functional –65 — 150 °C Temperature, Operating Ambient TA Functional –40 — 85 °C Temperature, Junction TJ Functional — — 150 °C Dissipation, Junction to Case (TDFN) ØJC JEDEC (JESD 51) — — 38.3 °C/W Dissipation, Junction to Case (TSSOP) ØJC JEDEC (JESD 51) — — 37.0 °C/W Dissipation, Junction to Ambient (TDFN) ØJA JEDEC (JESD 51) — — 90.4 °C/W Dissipation, Junction to Ambient (TSSOP) ØJA JEDEC (JESD 51) — — 124.0 °C/W Min Typ Table 5. Absolute Maximum Conditions Parameter Main Supply Voltage Input Voltage ESD Protection (Human Body Model) Flammability Rating Symbol Test Condition VDD_3.3V Max Unit — 4.6 V VIN Relative to VSS –0.5 4.6 VDC ESDHBM JEDEC (JESD 22 - A114) 2000 — V UL-94 UL (Class) V–0 Note: While using multiple power supplies, the voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is not required. 6 Rev 1.2 Si52111-B5/B6 2. Crystal Recommendations If using a crystal input, the device requires a parallel resonance crystal. Table 6. Crystal Recommendations Frequency Cut Loading Load Cap (Fund) 25 MHz AT Parallel ESR Drive Shunt Motional Tolerance Stability Cap (max) (max) (max) (max) 12–15 pF <50 >150 µW 5 pF 0.016 pF 35 ppm 30 ppm Aging (max) 5 ppm 2.1. Crystal Loading Crystal loading is critical in achieving low ppm performance. To realize low ppm performance, use the total capacitance the crystal sees to calculate the appropriate capacitive loading (CL). Figure 1 shows a typical crystal configuration using two trim capacitors. It is important that the trim capacitors are in series with the crystal. Figure 1. Crystal Capacitive Clarification Rev 1.2 7 Si52111 -B5/B6 2.2. Calculating Load Capacitors In addition to the standard external trim capacitors, consider the trace capacitance and pin capacitance to calculate the crystal loading correctly. Again, the capacitance on each side is in series with the crystal. The total capacitance on both sides is twice the specified crystal load capacitance (CL). Trim capacitors are calculated to provide equal capacitive loading on both sides. Figure 2. Crystal Loading Example Use the following formulas to calculate the trim capacitor values for Ce1 and Ce2. Load Capacitance (each side) Ce = 2 CL – Cs + Ci Total Capacitance (as seen by the crystal) 1 CLe = ------------------------------------------------------------------------------------------------------1 1 --------------------------------------------- + -------------------------------------------- Ce1 + Cs1 + Ci1 Ce2 + Cs2 + Ci2 CL: Crystal load capacitance CLe: Actual loading seen by crystal using standard value trim capacitors Ce: External trim capacitors Cs: Stray capacitance (terraced) Ci: Internal capacitance (lead frame, bond wires, etc.) 8 Rev 1.2 Si52111-B5/B6 3. Test and Measurement Setup Figures 3 through 5 show the test load configuration for the differential clock signals. M e a s u re m e n t P o in t L1 O UT+ 5 0 2 pF L1 = 5" O UT- M e a s u re m e n t P o in t L1 5 0 2 pF Figure 3. 0.7 V Differential Load Configuration Figure 4. Differential Measurement for Differential Output Signals (for AC Parameters Measurement) Rev 1.2 9 Si52111 -B5/B6 Figure 5. Single-Ended Measurement for Differential Output Signals (for AC Parameters Measurement) 10 Rev 1.2 Si52111-B5/B6 4. Pin Descriptions 4.1. 10-Pin TDFN VDD 1 10 VDD XOUT 2 9 NC XIN/CLKIN 3 8 NC VSS 4 7 DIFF1 VSS 5 6 DIFF1 Figure 6. 10-Pin TDFN Table 7. 10-Pin TDFN Descriptions Pin # Name Type Description 1 VDD 2 XOUT O 25.00 MHz crystal output, Float XOUT if using only CLKIN (clock input). 3 XIN/CLKIN I 25.00 MHz crystal input or 3.3 V, 25 MHz clock Input. 4 VSS GND Ground. 5 VSS GND Ground. 6 DIFF1 O, DIF 0.7 V, 100 MHz differentials clock output. 7 DIFF1 O, DIF 0.7 V, 100 MHz differentials clock output. 8 NC NC No Connect. Do not connect this pin to anything. 9 NC NC No Connect. Do not connect this pin to anything. 10 VDD PWR 3.3 V Power supply. PWR 3.3 V Power supply Rev 1.2 11 Si52111 -B5/B6 4.2. 8-Pin TSSOP VDD 1 8 NC XOUT 2 7 NC XIN/CLKIN 3 Si52111 VSS 4 6 DIFF1 5 DIFF1 Figure 7. 8-Pin TSSOP Table 8. 8-Pin TSSOP Descriptions Pin # Name 1 VDD 2 XOUT O 25.00 MHz crystal output, Float XOUT if using only CLKIN (clock input). 3 XIN/CLKIN I 25.00 MHz crystal input or 3.3 V, 25 MHz clock Input. 4 VSS GND 5 DIFF1 O, DIF 0.7 V, 100 MHz differentials clock. 6 DIFF1 O, DIF 0.7 V, 100 MHz differentials clock. 7 NC No Connect. Do not connect this pin to anything. 8 NC No Connect. Do not connect this pin to anything. 12 Type Description PWR 3.3 V Power supply. Ground. Rev 1.2 Si52111-B5/B6 5. Ordering Guide Part Number Spread Option Package Type Temperature Si52111-B5-GM2 No Spread 10-pin TDFN Extended, –40 to 85 °C Si52111-B5-GM2R No Spread 10-pin TDFN—Tape and Reel Extended, –40 to 85 °C Si52111-B5-GT No Spread 8-pin TSSOP Extended, –40 to 85 °C Si52111-B5-GTR No Spread 8-pin TSSOP - Tape and Reel Extended, –40 to 85 °C Si52111-B6-GM2 –0.5% Spread 10-pin TDFN Extended, –40 to 85 °C Si52111-B6-GM2R –0.5% Spread 10-pin TDFN—Tape and Reel Extended, –40 to 85 °C Si52111-B6-GT –0.5% Spread 8-pin TSSOP Extended, –40 to 85 °C Si52111-B6-GTR –0.5% Spread 8-pin TSSOP - Tape and Reel Extended, –40 to 85 °C Si52111 Bx Base part number B: Product Revision B x=5: non spread outputs x=6: -0.5% spread outputs GM2R/GTR Operating Temp Range: G: -40 to +85 °C M2 :10-TDFN Package, ROHS6, Pb-free T: 8-TSSOP Package, ROHS6, Pb-free R: Tape & Reel (blank) = Tubes Figure 8. Ordering Information Rev 1.2 13 Si52111 -B5/B6 6. Package Outlines 6.1. TDFN Package Figure 9 illustrates the package details for the 10-pin TDFN. Table 9 lists the values for the dimensions shown in the illustration. Figure 9. 10-Pin TDFN Package Drawing 14 Rev 1.2 Si52111-B5/B6 Table 9. TDFN Package Diagram Dimensions Symbol Min Nom Max A 0.70 0.75 0.80 A1 0.00 0.02 0.05 A3 b 0.20 REF. 0.18 D D2 0.25 0.30 3.00 BSC. 1.90 2.00 e 0.50 BSC E 3.00 BSC 2.10 E2 1.40 1.50 1.60 L 0.25 0.30 0.35 aaa 0.10 bbb 0.10 ccc 0.10 ddd 0.10 eee 0.08 Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. 4. This drawing conforms to the JEDEC Solid State Outline MO-229. Rev 1.2 15 Si52111 -B5/B6 6.2. TSSOP Package Figure 10 illustrates the package details for the 8-pin TSSOP. Table 10 lists the values for the dimensions shown in the illustration. Figure 10. 8-Pin TSSOP Package Drawing 16 Rev 1.2 Si52111-B5/B6 Table 10. TSSOP Package Diagram Dimensions Symbol Min Nom Max A — — 1.20 A1 0.05 — 0.15 A2 0.80 0.90 1.05 b 0.19 — 0.30 c 0.09 — 0.20 D 2.90 3.00 3.10 E E1 6.40 BSC 4.30 e L 4.50 0.65 BSC 0.45 L2 θ 4.40 0.60 0.75 0.25 BSC 0° — aaa 0.10 bbb 0.10 ccc 0.05 ddd 0.20 8° Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to the JEDEC Solid State Outline MO-153, Variation AA. 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for Small Body Components. Rev 1.2 17 Si52111 -B5/B6 7. Recommended Design Guideline 3.3 V VDD 4.7 µF 0.1 µF Si5211x Note: FB Specifications: DC resistance 0.1–0.3 Impedance at 100 MHz > 1000 Figure 11. Recommended Application Schematic 18 Rev 1.2 Si52111-B5/B6 DOCUMENT CHANGE LIST Revision 1.0 to Revision 1.1 Added “4.2. 8-Pin TSSOP” pin description on page 12. Revision 1.1 to Revision 1.2 Updated Features on page 1. Updated Description on page 1. Updated Table 3, “AC Electrical Specifications,” on page 4. Rev 1.2 19 ClockBuilder Pro One-click access to Timing tools, documentation, software, source code libraries & more. Available for Windows and iOS (CBGo only). www.silabs.com/CBPro Timing Portfolio www.silabs.com/timing SW/HW Quality Support and Community www.silabs.com/CBPro www.silabs.com/quality community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com