Si53159 PCI-E XPRESS G EN 1, G EN 2, G EN 3, AND G EN 4 N I NE O UTPUT F ANOUT B UFFER Features Ordering Information: See page 18. Applications Wireless access point Servers 45 44 43 42 41 40 SCLK VDD_CORE 46 CKPWRGD/PDB1 DIFFIN 47 SDATA DIFFIN 48 39 38 37 VDD_DIFF 1 36 DIFF8 VDD_DIFF 2 35 DIFF8 3 34 VDD_DIFF 4 33 DIFF7 VDD_DIFF 5 32 DIFF7 VSS_DIFF 6 31 DIFF6 VSS_DIFF 7 OE_DIFF21 8 OE_DIFF0 1 OE_DIFF1 1 49 GND 30 DIFF6 29 VSS_DIFF OE_DIFF3 1 9 28 DIFF5 OE_DIFF[4:5] 1 10 27 DIFF5 OE_DIFF[6:8]1 11 26 DIFF4 13 14 15 16 17 18 19 20 21 22 23 24 DIFF3 DIFF3 VDD_DIFF VSS_DIFF 12 DIFF2 VDD_DIFF 25 DIFF4 DIFF2 The Si53159 is a high-performance, low additive jitter, PCIe clock buffer that can fan out nine PCIe clocks. The clock outputs are compliant to PCIe Gen 1, Gen 2, Gen 3, and Gen 4 specifications. The device has six hardware output enable control pins for enabling and disabling differential outputs. The small footprint and low power consumption makes the Si53159 the ideal clock solution for consumer and embedded applications. Measuring PCIe clock jitter is quick and easy with the Silicon Labs PCIe Clock Jitter Tool. Download it for free at www.silabs.com/pcielearningcenter. NC Description NC Pin Assignments DIFF1 VSS_CORE DIFF1 Network attached storage Multi-function printers VSS_DIFF NC VSS_DIFF DIFF0 I2C support with readback capabilities Supports spread spectrum input Extended temperature: –40 to 85 °C 3.3 V power supply 48-pin QFN package NC Up to nine buffered clocks 100 to 210 MHz clock input range DIFF0 PCI-Express Gen 1, Gen 2, Gen 3, and Gen 4 common clock compliant Supports Serial-ATA (SATA) at 100 MHz Low power push-pull differential output buffers No termination resistors required Output enable pins for all buffered clocks VDD_DIFF Notes: 1. Internal 100 kohm pull-up. 2. Internal 100 kohm pull-down. Functional Block Diagram Patents pending DIFF0 DIFF1 DIFF2 DIFFIN DIFF3 DIFFIN DIFF4 DIFF5 SCLK SDATA OE [8:0] Control & Memory Control DIFF6 RAM DIFF7 DIFF8 Rev. 1.2 4/16 Copyright © 2016 by Silicon Laboratories Si53159 Si53159 2 Rev. 1.2 Si53159 TABLE O F C ONTENTS Section Page 1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2.1. CKPWRGD/PDB (Power Down) Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2.2. PDB (Power Down) Assertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2.3. PDB Deassertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2.4. OE Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2.5. OE Assertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2.6. OE Deassertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 3. Test and Measurement Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 4. Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 4.1. I2C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.2. Data Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 5. Pin Descriptions: 48-Pin QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7. Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 8. Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Rev. 1.2 3 Si53159 1. Electrical Specifications Table 1. DC Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit 3.3 V Operating Voltage VDD core 3.3 ± 5% 3.135 — 3.465 V 3.3 V Input High Voltage VIH Control input pins 2.0 — VDD + 0.3 V 3.3 V Input Low Voltage VIL Control input pins VSS – 0.3 — 0.8 V Input High Voltage VIHI2C SDATA, SCLK 2.2 — — V Input Low Voltage VILI2C SDATA, SCLK — — 1.0 V Input High Leakage Current IIH Except internal pull-down resistors, 0 < VIN < VDD — — 5 A Input Low Leakage Current IIL Except internal pull-up resistors, 0 < VIN < VDD –5 — — A High-impedance Output Current IOZ –10 — 10 A Input Pin Capacitance CIN 1.5 — 5 pF COUT — — 6 pF LIN — — 7 nH Power Down Current IDD_PD — — 1 mA Dynamic Supply Current in Fanout Mode IDD_3.3V — — 60 mA Output Pin Capacitance Pin Inductance 4 All outputs enabled, 5” traces; 2 pF load, frequency at 100 MHz Rev. 1.2 Si53159 Table 2. AC Electrical Specifications Parameter Symbol Condition Min Typ Max Unit TR / TF Single ended measurement: VOL = 0.175 to VOH = 0.525 V (Averaged) 0.6 — 4 V/ns DIFFIN at 0.7 V DIFFIN and DIFFIN Rising/Falling Slew Rate Differential Input High Voltage VIH 150 — — mV Differential Input Low Voltage VIL — — –150 mV Crossing Point Voltage at 0.7 V Swing VOX Single-ended measurement 250 — 550 mV Vcross Variation Over All edges VOX Single-ended measurement — — 140 mV VRB –100 — 100 mV TSTABLE 500 — — ps — 1.15 V –0.3 — — V Differential Ringback Voltage Time before Ringback Allowed Absolute Maximum Input Voltage VMAX Absolute Minimum Input Voltage VMIN DIFFIN and DIFFIN Duty Cycle TDC Measured at crossing point VOX 45 — 55 % Rise/Fall Matching TRFM Determined as a fraction of 2 x (TR – TF)/(TR + TF) — — 20 % Duty Cycle TDC Measured at 0 V differential 45 — 55 % Clock Skew TSKEW Measured at 0 V differential — — 50 ps PCIe Gen1 Pk-Pk Jitter Pk-Pk PCIe Gen 1 0 — 10 ps PCIe Gen 2 Phase Jitter RMSGEN2 10 kHz < F < 1.5 MHz 0 — 0.5 ps 1.5 MHz < F < Nyquist 0 — 0.5 ps DIFF at 0.7 V PCIe Gen 3 Phase Jitter RMSGEN3 Includes PLL BW 2–4 MHz, CDR = 10 MHz 0 — 0.10 ps Additive PCIe Gen 4 Phase Jitter RMSGEN4 PCIe Gen 4 — — 0.10 ps Additive Cycle to Cycle Jitter TCCJ In buffer mode. Measured at 0 V differential — 20 50 ps Long-term Accuracy LACC Measured at 0 V differential — — 100 ppm TR / T F Measured differentially from ±150 mV 2.5 — 8 V/ns 300 — 550 mV Rising/Falling Slew rate Crossing Point Voltage at 0.7 V Swing VOX Notes: 1. Visit www.pcisig.com for complete PCIe specifications. 2. Gen 4 specifications based on the PCI-Express Base Specification 4.0 rev. 0.5. 3. Download the Silicon Labs PCIe Clock Jitter Tool at www.silabs.com/pcie-learningcenter. Rev. 1.2 5 Si53159 Table 2. AC Electrical Specifications (Continued) Parameter Symbol Condition Min Typ Max Unit TSTABLE Measured from the point when both VDD and clock input are valid — — 1.8 ms 10.0 — — ns Enable/Disable and Setup Clock Stabilization from Power-Up Stopclock Set-up Time TSS Notes: 1. Visit www.pcisig.com for complete PCIe specifications. 2. Gen 4 specifications based on the PCI-Express Base Specification 4.0 rev. 0.5. 3. Download the Silicon Labs PCIe Clock Jitter Tool at www.silabs.com/pcie-learningcenter. Table 3. Absolute Maximum Conditions Parameter Symbol Condition Min Typ Max Unit VDD_3.3V Functional — — 4.6 V Input Voltage VIN Relative to VSS –0.5 — 4.6 VDC Temperature, Storage TS Non-functional –65 — 150 °C Extended Temperature, Operating Ambient TA Functional –40 — 85 °C Temperature, Junction TJ Functional — — 150 °C Dissipation, Junction to Case ØJC JEDEC (JESD 51) — — 22 °C/W Dissipation, Junction to Ambient ØJA JEDEC (JESD 51) — — 30 °C/W ESDHBM JEDEC (JESD 22 - A114) 2000 — — V UL-94 UL (Class) Main Supply Voltage ESD Protection (Human Body Model) Flammability Rating V–0 Note: Multiple Supplies: The voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is not required. 6 Rev. 1.2 Si53159 2. Functional Description 2.1. CKPWRGD/PDB (Power Down) Pin The CKPWRGD/PDB pin is a dual-function pin. During initial power up, the pin functions as the CKPWRGD pin. Upon the first power up, if the CKPWRGD pin is low, the outputs will be disabled, but the crystal oscillator and I2C logic will be active. Once the CKPWRGD pin has been sampled high by the clock chip, the pin assumes a PDB functionality. When the pin has assumed a PDB functionality and is pulled low, the device will be placed in power down mode. The CKPWRGD/PDB pin is required to be driven at all times even though it has an internal 100 k resistor. 2.2. PDB (Power Down) Assertion The PDB pin is an asynchronous active low input used to disable all output clocks in a glitch-free manner. All outputs will be driven low in power down mode. In power down mode, all outputs, the crystal oscillator, and the I2C logic are disabled. 2.3. PDB Deassertion When a valid rising edge on CKPWRGD/PDB pin is applied, all outputs are enabled in a glitch-free manner within two to six output clock cycles. 2.4. OE Pin The OE pin is an active high input used to enable and disable the output clock. To enable the output clock, the OE pin and the I2C OE bit need to be a logic high. By default, the OE pin and the I2C OE bit are set to a logic high. There are two methods to disable the output clock: the OE pin is pulled to a logic low, or the I2C OE bit is set to a logic low. The OE pin is required to be driven at all times even though it has an internal 100 k resistor. 2.5. OE Assertion The OE pin is an active high input used for synchronous stopping and starting the respective output clock while the rest of the clock generator continues to function. The assertion of the OE function is achieved by pulling the OE pin and the I2C OE bit high which causes the respective stopped output to resume normal operation. No short or stretched clock pulses are produced when the clocks resume. The maximum latency from the assertion to active outputs is no more than two to six output clock cycles. 2.6. OE Deassertion The OE function is deasserted by pulling the pin or the I2C OE bit to a logic low. The corresponding output is stopped cleanly and the final output state is driven low. Rev. 1.2 7 Si53159 3. Test and Measurement Setup This diagram shows the test load configuration for the differential clock signals. Figure 1. 0.7 V Differential Load Configuration Figure 2. Differential Measurement for Differential Output Signals (for AC Parameters Measurement) 8 Rev. 1.2 Si53159 VMIN = –0.30V VMIN = –0.30V Figure 3. Single-Ended Measurement for Differential Output Signals (for AC Parameters Measurement) Rev. 1.2 9 Si53159 4. Control Registers 4.1. I2C Interface To enhance the flexibility and function of the clock synthesizer, an I2C interface is provided. Through the I2C interface, various device functions, such as individual clock output buffers are individually enabled or disabled. The registers associated with the I2C interface initialize to their default setting at power-up. The use of this interface is optional. Clock device register changes are normally made at system initialization, if any are required. 4.2. Data Protocol The clock driver I2C protocol accepts byte write, byte read, block write, and block read operations from the controller. For block write/read operation, access the bytes in sequential order from lowest to highest (most significant bit first) with the ability to stop after any complete byte is transferred. For byte write and byte read operations, the system controller can access individually indexed bytes. The block write and block read protocol is outlined in Table 4 on page 10 while Table 5 on page 11 outlines byte write and byte read protocol. The slave receiver address is 11010110 (D6h). Table 4. Block Read and Block Write Protocol Block Write Protocol Bit 1 8:2 Description Bit Start 1 Slave address—7 bits 8:2 Description Start Slave address—7 bits 9 Write 9 Write 10 Acknowledge from slave 10 Acknowledge from slave 18:11 Command Code—8 bits 18:11 19 Acknowledge from slave 19 Acknowledge from slave Byte Count—8 bits 20 Repeat start 27:20 28 36:29 37 45:38 10 Block Read Protocol Acknowledge from slave 27:21 Command Code–8 bits Slave address—7 bits Data byte 1–8 bits 28 Read = 1 Acknowledge from slave 29 Acknowledge from slave Data byte 2–8 bits 46 Acknowledge from slave .... Data Byte/Slave Acknowledges .... Data Byte N–8 bits .... Acknowledge from slave .... Stop 37:30 38 46:39 47 55:48 Rev. 1.2 Byte Count from slave—8 bits Acknowledge Data byte 1 from slave—8 bits Acknowledge Data byte 2 from slave—8 bits 56 Acknowledge .... Data bytes from slave/Acknowledge .... Data Byte N from slave—8 bits .... NOT Acknowledge .... Stop Si53159 Table 5. Byte Read and Byte Write Protocol Byte Write Protocol Bit 1 8:2 Byte Read Protocol Description Bit Start 1 Slave address–7 bits 8:2 Description Start Slave address–7 bits 9 Write 9 Write 10 Acknowledge from slave 10 Acknowledge from slave 18:11 19 27:20 Command Code–8 bits 18:11 Command Code–8 bits Acknowledge from slave 19 Acknowledge from slave Data byte–8 bits 20 Repeated start 28 Acknowledge from slave 29 Stop 27:21 28 Read 29 Acknowledge from slave 37:30 Rev. 1.2 Slave address–7 bits Data from slave–8 bits 38 NOT Acknowledge 39 Stop 11 Si53159 Control Register 0. Byte 0 Bit D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W D2 D1 D0 DIFF1_OE DIFF2_OE DIFF3_OE R/W R/W R/W Name Type Reset settings = 00000000 Bit Name 7:0 Reserved Function Control Register 1. Byte 1 Bit D7 D6 D5 Name Type D4 D3 DIFF0_OE R/W R/W R/W R/W R/W Reset settings = 00010111 Bit Name 7:5 Reserved 4 DIFF0_OE Function Output Enable for DIFF0. 0: Output disabled. 1: Output enabled. 3 Reserved 2 DIFF1_OE Output Enable for DIFF1. 0: Output disabled. 1: Output enabled. 1 DIFF2_OE Output Enable for DIFF2. 0: Output disabled. 1: Output enabled. 0 DIFF3_OE Output Enable for DIFF3. 0: Output disabled. 1: Output enabled. 12 Rev. 1.2 Si53159 Control Register 2. Byte 2 Bit D7 D6 D5 D4 D3 Name DIFF4_OE DIFF5_OE DIFF6_OE DIFF7_OE DIFF8_OE Type R/W R/W R/W R/W R/W D2 D1 D0 R/W R/W R/W Reset settings = 11111000 Bit Name 7 DIFF4_OE Function Output Enable for DIFF4. 0: Output disabled. 1: Output enabled. 6 DIFF5_OE Output Enable for DIFF5. 0: Output disabled. 1: Output enabled. 5 DIFF6_OE Output Enable for DIFF6. 0: Output disabled. 1: Output enabled. 4 DIFF7_OE Output Enable for DIFF7. 0: Output disabled. 1: Output enabled. 3 DIFF8_OE Output Enable for DIFF8. 0: Output disabled. 1: Output enabled. 2:0 Reserved Rev. 1.2 13 Si53159 Control Register 3. Byte 3 Bit D7 D6 Name Type D5 D4 D3 D2 Rev Code[3:0] R/W R/W R/W D1 D0 Vendor ID[3:0] R/W R/W R/W R/W R/W D3 D2 D1 D0 R/W R/W R/W R/W Reset settings = 00001000 Bit Name Function 7:4 Rev Code[3:0] Program Revision Code. 3:0 Vendor ID[3:0] Vendor Identification Code. Control Register 4. Byte 4 Bit D7 D6 D5 D4 Name Type BC[7:0] R/W R/W R/W R/W Reset settings = 00000110 Bit Name 7:0 BC[7:0] Function Byte Count Register. Control Register 5. Byte 5 Bit D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W Name DIFF_Amp_Sel DIFF_Amp_Cntl[2] DIFF_Amp_Cntl[1] DIFF_Amp_Cntl[0] Type R/W R/W R/W R/W Reset settings = 11011000 Bit Name 7 DIFF_Amp_Sel Function Amplitude Control for DIFF Differential Outputs. 0: Differential outputs with Default amplitude. 1: Differential outputs amplitude is set by Byte 5[6:4]. 14 6 DIFF_Amp_Cntl[2] 5 DIFF_Amp_Cntl[1] 4 DIFF_Amp_Cntl[0] 3:0 Reserved DIFF Differential Outputs Amplitude Adjustment. 000: 300 mV 001: 400 mV 010: 500 mV 100: 700 mV 101: 800 mV 110: 900 mV Rev. 1.2 011: 600 mV 111: 1000 mV Si53159 NC NC VSS_DIFF VSS_CORE NC NC DIFFIN DIFFIN VDD_CORE CKPWRGD/PDB1 SDATA SCLK 5. Pin Descriptions: 48-Pin QFN 48 47 46 45 44 43 42 41 40 39 38 37 VDD_DIFF 1 36 DIFF8 VDD_DIFF 2 35 DIFF8 OE_DIFF0 1 3 34 VDD_DIFF OE_DIFF1 1 4 33 DIFF7 VDD_DIFF 5 32 DIFF7 VSS_DIFF 6 31 DIFF6 VSS_DIFF 7 30 DIFF6 OE_DIFF2 1 8 29 VSS_DIFF OE_DIFF3 1 9 28 DIFF5 OE_DIFF[4:5]1 10 27 DIFF5 OE_DIFF[6:8]1 11 26 DIFF4 VDD_DIFF 12 49 GND 17 18 19 20 21 VSS_DIFF DIFF1 DIFF1 DIFF2 DIFF2 DIFF3 22 23 24 VSS_DIFF 16 VDD_DIFF 15 DIFF3 14 DIFF0 VDD_DIFF 13 DIFF0 25 DIFF4 Notes: 1. Internal 100 kohm pull-up. 2. Internal 100 kohm pull-down. . Table 6. Si53159 48-Pin QFN Descriptions Pin # Name Type Description 1 VDD_DIFF PWR 3.3 V power supply. 2 VDD_DIFF PWR 3.3 V power supply. 3 OE_DIFF0 I,PU Active high input pin enables DIFF0 (internal 100 k pull-up). 4 OE_DIFF1 I,PU Active high input pin enables DIFF1 (internal 100 k pull-up). 5 VDD_DIFF PWR 3.3 V power supply. 6 VSS_DIFF GND Ground. 7 VSS_DIFF GND Ground. 8 OE_DIFF2 I,PU Active high input pin enables DIFF2 (internal 100 k pull-up). Rev. 1.2 15 Si53159 Table 6. Si53159 48-Pin QFN Descriptions Pin # Name Type 9 OE_DIFF3 I,PU Active high input pin enables DIFF3 (internal 100 k pull-up). 10 OE_DIFF[4:5] I,PU Active high input pin enables DIFF[4:5] (internal 100 k pull-up). 11 OE_DIFF[6:8] I,PU Active high input pin enables DIFF[6:8] (internal 100 k pull-up). 12 VDD_DIFF PWR 3.3 V power supply. 13 VDD_DIFF PWR 3.3 V power supply. 14 DIFF0 O, DIF 0.7 V, 100 MHz differential clock. 15 DIFF0 O, DIF 0.7 V, 100 MHz differential clock. 16 VSS_DIFF 17 DIFF1 O, DIF 0.7 V, 100 MHz differential clock. 18 DIFF1 O, DIF 0.7 V, 100 MHz differential clock. 19 DIFF2 O, DIF 0.7 V, 100 MHz differential clock. 20 DIFF2 O, DIF 0.7 V, 100 MHz differential clock. 21 DIFF3 O, DIF 0.7 V, 100 MHz differential clock. 22 DIFF3 O, DIF 0.7 V, 100 MHz differential clock. 23 VDD_DIFF PWR 3.3V power supply. 24 VSS_DIFF GND 25 DIFF4 O, DIF 0.7 V, 100 MHz differential clock. 26 DIFF4 O, DIF 0.7 V, 100 MHz differential clock. 27 DIFF5 O, DIF 0.7 V, 100 MHz differential clock. 28 DIFF5 O, DIF 0.7 V, 100 MHz differential clock. 29 VSS_DIFF 30 DIFF6 O, DIF 0.7 V, 100 MHz differential clock. 31 DIFF6 O, DIF 0.7 V, 100 MHz differential clock. 32 DIFF7 O, DIF 0.7 V, 100 MHz differential clock. 33 DIFF7 O, DIF 0.7 V, 100 MHz differential clock. 34 VDD_DIFF 35 DIFF8 O, DIF 0.7 V, 100 MHz differential clock. 36 DIFF8 O, DIF 0.7 V, 100 MHz differential clock. 37 SCLK 16 GND GND Description Ground. Ground. Ground. PWR 3.3 V power supply. I I2C compatible SCLOCK. Rev. 1.2 Si53159 Table 6. Si53159 48-Pin QFN Descriptions Pin # Name Type Description 2 38 SDATA I/O I C compatible SDATA. 39 CKPWRGD/PDB I, PU 40 VDD_CORE 41 DIFFIN I 0.7 V Differential True Input, typically 100 MHz. Input frequency range 100 to 210 MHz. 42 DIFFIN O 0.7 V Differential Complement Input, typically 100 MHz. Input frequency range 100 to 210 MHz. 43 NC NC No connect. 44 NC NC No connect. 45 VSS_CORE GND Ground for core. 46 VSS_DIFF GND Ground. 47 NC NC No connect. 48 NC NC No connect. 49 GND GND Active low input pin asserts power down (PDB) and disables all outputs (internal 100 k pull-up). PWR 3.3 V power supply for core. Ground for bottom pad of the IC. Rev. 1.2 17 Si53159 6. Ordering Guide Part Number Package Type Temperature Si53159-A01AGM 48-pin QFN Extended, –40 to 85 C Si53159-A01AGMR 48-pin QFN—Tape and Reel Extended, –40 to 85 C Lead-free 18 Rev. 1.2 Si53159 7. Package Outline Figure 4 illustrates the package details for the Si53159. Table 7 lists the values for the dimensions shown in the illustration. Figure 4. 48-Pin Quad Flat No Lead (QFN) Package Table 7. Package Diagram Dimensions Symbol Millimeters Min Nom Max 0.70 0.75 0.80 A1 0.00 0.025 0.05 b 0.15 0.20 0.25 A D D2 6.00 BSC 4.30 4.40 e 0.40 BSC E 6.00 BSC 4.50 E2 4.30 4.40 4.50 L 0.30 0.40 0.50 aaa 0.10 bbb 0.10 ccc 0.08 ddd 0.07 Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to JEDEC outline MO-220, variation VGGD-8 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components Rev. 1.2 19 Si53159 8. Land Pattern Figure 5 illustrates the recommended land pattern details for the Si53159 in a 48-pin QFN package. Table 8 lists the values for the dimensions shown in the illustration. Y1 E X1 Y2 X2 C1 Figure 5. Land Pattern 20 Rev. 1.2 C2 Si53159 Table 8. PCB Land Pattern Dimensions Dimension Min Max C1 5.85 5.95 C2 5.85 5.95 X1 0.15 0.25 Y1 0.80 0.90 E X2 0.40 BSC 4.35 4.45 4.35 4.45 Notes: General 1. All dimensions shown are in millimeters (mm). 2. This Land Pattern Design is based on the IPC-7351 guidelines. Solder Mask Design 1. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 m minimum, all the way around the pad. Stencil Design 1. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 2. The stencil thickness should be 0.125mm (5 mils). 3. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pads. 4. A 4x4 array of 0.80mm square openings on 1.05mm pitch should be used for the center ground pad to achieve between 50-60% solder coverage. Card Assembly 1. A No-Clean, Type-3 solder paste is recommended. 2. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. Rev. 1.2 21 Si53159 DOCUMENT CHANGE LIST Revision 0.1 to Revision 1.0 Updated Features and Description. Corrected pinout. Updated Table 2. Updated Section 2.1. Updated Section 2.1.1. Updated Sections 2.2 through 2.8. Updated Section 4.2. Updated Table 7. Revision 1.0 to Revision 1.1 Updated Features on page 1. Updated Description on page 1. Updated specs in Table 2, “AC Electrical Specifications,” on page 5. Revision 1.1 to Revision 1.2 Added condition for Clock Stabilization from Powerup, TSTABLE, in Table 2. Rev. 1.2 22 ClockBuilder Pro One-click access to Timing tools, documentation, software, source code libraries & more. Available for Windows and iOS (CBGo only). www.silabs.com/CBPro Timing Portfolio www.silabs.com/timing SW/HW www.silabs.com/CBPro Quality www.silabs.com/quality Support and Community community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are not designed or authorized for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®, ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com