Rack Panel

Rack & Panel
Rack & Panel
Rectangular
■
Miniature
■
Subminiature
■
Environmental
■
Removable Contacts
Table Of Contents
Series
MRAC
Description
Page
Miniature Rectangular Connectors With Removable Contacts
2 - 10
External Miniature Rectangular Connectors With Removable Contacts
11 - 20
Heavy Duty, Industrial and Commercial, Miniature Rectangular
Rack and Panel Connectors With Removable Contacts
21 - 22
TXAC
Heavy Duty, Industrial and Commercial, External Miniature Rectangular
Rack and Panel Connector With Removable Contacts
23 - 24
MRA
Miniature Rectangular / #16 Contacts / .062" Dia. / 13 Amps
25 - 33
MRE
Miniature Rectangular / #20 Contacts / .040" Dia. / 7.5 Amps
34 - 43
XMRA and
XMRE
External Miniature Rectangular / #16 Contacts / .062" Dia. / 13 Amps
#20 Contacts / .040" Dia. / 7.5 Amps
44 - 53
SLE, SME
and SRE
Sub Miniature / High Density Rectangular / .025" Dia. / 3 Amps
.030" Dia. / 5 Amps ■ .040" Dia. / 7.5 Amps
54 - 57
Sub Miniature Rectangular Connector With Removable Contacts
58 - 60
Panel Mount Miniature / 22 AWG / .030" Dia. / 5 Amps
61 - 64
SRM
Sub Miniature Rectangular / #20 Contacts / .040" Dia. / 7.5 Amps
65 - 70
PM1
High Voltage, Single Contact / #20 Contacts / .040" Dia. / 7.5 Amps
71
PM6
High Voltage Miniature / #20 Contacts / .040" Dia. / 7.5 Amps
72
Sub Miniature / #20 Contacts / 3 and 7.5 Amps
73 - 74
M
High Voltage Miniature / #20 Contacts / .040" Dia. / 7.5 Amps
75 - 78
JF
Miniature Side Mount / #20 Contacts / .040" Dia. / 7.5 Amps
79 - 81
JFA
Miniature Side Mount / #16 Contacts / .062" Dia. / 13 Amps
82
100
Removable Contacts
83 - 91
107
Tools and Accessories
92 - 93
Global Sales Support
94
XAC
TMRAC
SREC
42
SM
Locations
Contact a Winchester Electronics sales representative for your
V.35 Rack & Panel Data Communications Connectors
While the information in this publication is believed to be accurate and reliable, all data presented is
subject to change without notice. Winchester Electronics disclaims responsibility for any damages
resulting from application or any incompleteness or inaccuracies in the information presented.
Consult factory for specific information on the latest design specifications.
© 1999, WinchesterElectronics
Electronics
Winchester
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 1
Rack & Panel3DUN5RDG([W6XLWH
MRAC Series
Miniature Rectangular, Removable Contacts
FEATURES
■ Closed Entry
Removable Socket
and Pin Contacts.
■ Connector Inserts with
9 to 104 Contacts.
■ Quick Crimp ... Snap in
Place!
■ To remove ... insert
removal tool — “Push
Out” Contact!
Removable contacts offer a substantial savings
of time, labor and a great flexibility in the choice
of circuitry. The contact is easily removed with
the hand tool depicted and then placed by
hand or with a simple insertion tool.
The MRAC Series is an important extension of the MRA line featuring a variety
of crimp and solder removable contact styles. Except for body thickness, they
are similar and interchangeable with the MRA Series.
SPECIFICATIONS
Current Rating: Up to 13 amps
No. of
Contacts:
9, 14, 18, 20, 26, 34, 41, 42,
50, 66, 75, 104
Contacts:
Must be ordered separately.
Select from crimp, solder, dip
solder, shielded or WireWrap termination contacts.
See 100 Series contact
section.
Contact
Identificaiton: Standard contact identification is alphabetical except for
MRAC66 and 75 which have
numerical identification. To
order numerical identification
on MRAC 34, 50 or 104,
specify MNAC**P or S.
MILITARY CROSS REFERENCE
CATALOG NO.
MRAC 9P
MRAC 9S
MRAC 14P
MRAC 14S
MRAC 20P
MRAC 20S
MRAC 26P
MRAC 26S
MRAC MS34P
MRAC MS34S
MS
MS
MS
MS
MS
MS
MS
MS
MS
MS
14007-1
14006-1
18174-1
18175-1
18176-1
18177-1
14008-1
14005-1
18178-1
18179-1
CATALOG NO.
MRAC 42P
MRAC 42S
MRAC 50P
MRAC 50S
MRAC 66P
MRAC 66S
MRAC 75P
MRAC 75S
MRAC 104P
MRAC 104S
MS
MS
MS
MS
MS
MS
MS
MS
MS
MS
Electrical Data: Meets high potential
performance of MIL-C-28748.
The dielectric withstanding
voltage is one minute
electrification at 2000 VAC
(sea level).
Dielectric:
MRAC Series: Standard glass
filled diallyl phthalate, per MILM-14, SDG-F, color gray.
Qualification: Military Versions are QPL’d to
M28748/3 and M28748/4.
Polarization: Gold plated guides provide
positive polarization. Polarized
nickel-plated brass and/or
passivated stainless steel with
anodized aluminum knobs available.
Hoods:
Anodized aluminum. May be
applied to either plug or
receptacle. Both top and side
opening hoods available.
18180-1
18181-1
18182-1
18183-1
18184-1
18185-1
18187-1
18188-1
18189-1
18190-1
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXWPhone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 2
Rack & Panel
Miniature Rectangular, Removable Contacts
MRAC Series
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Drawings and corresponding part numbers
show G type guide sockets. It is recommended that guides be used wherever
.86
.38
4-40
UNC 2A
THD.
.075
Typ.
.78
Slot
.038
Wide
.27
possible for positive polarization and for
protection of contacts except for the MRAC
104 where the jackscrew locking device is
recommended.
.86
.27
.27
.44
4-40
UNC 2A
THD.
1.250
.075
Typ.
1.313
.81
.937
.78
Slot
.038
Wide
.37
.27
.37
.78
1.000
.09R
.172
Typ.
.09R
.37
.13R
.130 Typ.
.52
.86
MRAC 9S-G
MRAC 9P-G
.86
.52
MRAC 14S-G
MRAC 14P-G
.86
.78
.86
.27
.56
.37
4-40
UNC 2A
THD.
.075
Typ.
Slot
.038
Wide
.37
.44
.27
.27
.22
4-40
UNC 2A
THD.
.075
Typ.
.37
.78
.27
Slot
.038
Wide
.37
1.313
1.563
1.000
.09R
.78
1.250
.13R
.130 Typ.
MRAC 18S-G
.13R
.130 Typ.
.09R
.52
.86
MRAC 18P-G
1.078
.86
.52
MRAC 20S-G
MRAC 20P-G
PHYSICAL DATA
Plug
Code
No.
MRAC9P
MRAC14P
MRAC18P
MRAC20P
MRAC26P
MRAC34P
Recepticle No. of Wt. in Ozs.
Code
Contactsw/o Contacts
No.
Plug Rec.
MRAC9S
MRAC14S
MRAC18S
MRAC20S
MRAC26S
MRAC34S
9
14
18
20
26
34
.15
.17
.17
.17
.42
.42
.17
.2
.2
.25
.67
.67
Plug
Code
No.
MRAC41
MRAC42P
MRAC50P
MRAC66P
MRAC75P
MRAC104P
Recepticle No. of Wt. in Ozs.
Code
Contactsw/o Contacts
No.
Plug Rec.
MRAC41S
MRAC42S
MRAC50S
MRAC66S
MRAC75S
MRAC104S
41
42
50
66
75
104
.5
.5
.6
.7
.9
1.2
.7
.7
.85
1.05
1.3
1.78
GUIDE SOCKETS
How To Order: To obtain “K” or “N”
guides in place of the standard “G” type,
substitute the desired socket style code
letter (“K” or “N”) for “G” in both the Plug
and Receptacle Code Numbers.
Guide
Socket
Code Letter
Actual
Size Photo
G*
For General Use
Phosphor Bronze
K*
N*
Winchester/Retconn
For High Electrical
Conductivity Beryllium
Copper
Standard Guide
Pin mates with all types
Brass
For Extra Mechanical
Strength Brass
* For passivated stainless steel add SS suffix
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 3
Rack & Panel
Miniature Rectangular, Removable Contacts
MRAC Series
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
4-40 UNC
2A THD
.56
.075
Typ
.86
.27
Slot
.038
Wide
.37
.75
.78
.27
.37
.23
.075
Typ
.78
.86
.47
.09R 4-40 UNC
2A THD
.27
.37
Slot
.038
Wide
.27
.37
1.625
2.000
1.312
1.072
.09R
.13R
.130 Typ
Mounting
holes for
number 4
machine
screws
.52
.86
MRAC 26S-G
.22
.075
Typ
.180 Typ
MRAC 26P-G
.86
.44
1.375
1.688
.27
4-40 UNC
2A THD
.37
Slot
.038
Wide
.78
.37
MRAC 34P-G
.75
.27
.47
.075
Typ
.23
.52
.86
MRAC 34S-G
.86
.09R
.27
4-40 UNC
2A THD
.37
Slot
.038
Wide
.78
.37 .27
2.625
2.312
2.313
2.125
Mounting
holes for
number 4
machine
screws
.09R
1.672
2.000
.73
.13R
.130 Typ
MRAC 41S-G
.86
.52
MRAC 41P-G
.52
.86
.180 Typ
MRAC 42S-G
MRAC 42P-G
Drawings and corresponding part numbers show G type guide sockets except
for the MRAC104P and S which show JT hardware.
Mounting Note: Connectors MRAC 26, MRAC 20 and smaller, use guides for mounting in a hood or on a
panel. Connectors MRAC 34, MRAC 42, MRAC 50, MRAC 66, and MRAC 75 use four #4 machine screws, in
addition to guides, for mounting in a hood or on a panel. Guides are not recommended for use with MRAC
104. MRAC 104 uses four #6 machine screws for mounting.
*For numerical contact identification instead of alphabetical, order MNAC._______P or S available in sizes 34,
50 and 104. Example MNAC 34P. MRAC 66 and 75 have numerical contact identification as standard.
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXWPhone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 4
Rack & Panel
Miniature Rectangular, Removable Contacts
MRAC Series
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.88
.47
4-40 .14
UNC
2A THD
.23
.075
Typ
.86
.27
.75
.37
.09
Slot
.78
.27
1.125
.50
.25
.150
Typ
.37
.86
4-40
UNC
2A THD
1.969
Mounting
holes for
number 4
machine
screws
2.282
.16R
.180 Typ
.86
MRAC 50S-G
1.234
.86
.37
.27
4-40
.14
UNC
2A THD
.23
.075
Typ
1.109
.31R
.09
Slot
MRAC 66S-G
1.531
.88
.78
.27
.37
.075
Typ
.44
1.359
.038 Dia. holes
.37
for safety wire
.038
Wide
2.594
.16R
.180 Typ
MRAC 75S-G
.16
.80
.27
.37
.16
6-32
UNC
2A THD.
2.375
2.000
1.094
.52
8-32
UNC
2A
THD.
2.750
2.719
Mounting
holes for
number 4
machine
screws
.86
MRAC 66P-G
2.282
.97
.37 .27
1.672
.180 Typ
.52
MRAC 50P-G
.77
Slot
2.281
2.719
1.109
.37
.038
Wide
2.594
.73
.78
.038
Wide
1.97
Mounting
holes for
number 4
machine
screws
.27
.86
MRAC 75P-G
.52
Mounting
holes for
number 6
machine
screws
1.469
.38R
.180 Typ
MRAC 104S-JT *
.86
.52
.16
.16
MRAC 104P-J
Drawings and corresponding part numbers show G type guide sockets except
for the MRAC104P and S which show JT hardware.
Mounting Note: Connectors MRAC 26, MRAC 20 and smaller, use guides for mounting in a hood or on a
panel. Connectors MRAC 34, MRAC 42, MRAC 50, MRAC 66, and MRAC 75 use four #4 machine screws, in
addition to guides, for mounting in a hood or on a panel. Guides are not recommended for use with MRAC
104. MRAC 104 uses four #6 machine screws for mounting.
*For numerical contact identification instead of alphabetical, order MNAC._______P or S available in sizes 34,
50 and 104. Example MNAC 34P. MRAC 66 and 75 have numerical contact identification as standard.
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 5
Rack & Panel
Miniature Rectangular, Removable Contacts
MRAC Series
JACKSCREWS & JACKSOCKETS
Polarized jackscrews give the ease and
assurance of threaded positive coupling.
The actuating side consists of two turnable
screws, one male and one female, each with
knurled and slotted knobs. On the mating half
OUTLINE
are the two fixed screws required to
complete the locking action. When mated,
the jackscrews may be locked with a safety
wire through the hole in the self-locking pin
(in the jackscrew shaft).
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
4-40 UNC except size
104/6-32 UNC
6-32 UNC THD. except
size 104/8-32 UNC
Jacksocket
.78
Side Cable
Opening
.16
MonoJackscrew
A
Side Cable
Opening
B
Top Cable
Opening
Top Cable
Opening
.16
Jackscrew
C
Connector with fixed Jackscrews
Code designation: J
D
AND
Mating connector half with turnable
Jackscrews-with-Knobs.
Code designation: JT
Hood
Self Locking
Pin
E
OR
Mating connector half with Hood and
turnable Long Jackscrews-withKnobs. Code designation: JTC H,
JTC H1
052 Dia. Safety
Wire Hole
F
MonoJacksocket
OR
Mating connector half with Hood and
turnable Monojacks.
Code designation: JTDH, JTDH1
DIMENSIONS
Connector
Size
MRAC 9
MRAC 14
MRAC 18
MRAC 20
MRAC 26
MRAC 34
MRAC 41
MRAC 42
MRAC 50
MRAC 66
MRAC 75
MRAC 104
H
–
–
–
–
.80
.63
.63
.58
.58
.69
.56
.5
Dimension A
Dimension B
H1 H8 H9 H13 H H1 H8 H9 C
.59
.59
.59
.59
.59
.63
.63
.58
.58
–
.56
–
–
–
–
–
.59
.63
–
.58
.58
–
.56
–
–
–
–
–
.59
.63
–
.58
.58
.69
.56
.67
.59
.59
.59
.59
–
–
–
–
–
–
–
–
–
–
–
–
–
.63
–
.58
.58
.5
.56
.5
–
–
–
–
–
.63
–
.58
.58
–
.56
–
–
–
–
–
–
.63
–
.58
.58
–
.56
–
–
–
–
–
–
.63
–
.58
.58
.5
.56
.5
.80
.80
.80
.80
.80
.80
.80
.80
.80
.80
.80
.80
D
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.52
Dimension E
Dimension F
H H1 H8 H9 H13 H H1 H8 H9
–
–
–
–
2.61
2.41
2.41
2.41
2.41
2.41
2.41
3.42
2.41
2.41
2.41
2.41
2.41
2.41
2.41
2.41
2.41
–
2.41
–
–
–
–
–
–
–
–
–
2.41 2.41
2.41 –
–
–
2.41 –
2.41 –
– 2.41
2.41 –
– 3.42
2.41
2.41
2.41
2.41
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
2.41
2.41
2.41
2.41
3.25
–
–
–
–
–
2.41
–
2.41
2.41
–
2.41
–
–
–
–
–
–
2.41
–
2.41
2.41
–
2.41
–
–
–
–
–
–
2.41
–
2.41
2.41
2.41
2.41
3.25
New Monojacks Assemble and Disassemble With Remarkable Ease and Speed
To free the connector from the hood, simply
remove four screws. Monojacks may be used
on miniature rectangular connectors with from
34 to 104 contacts and with molds featuring
guide hole and two mounting holes on both
ends. Molds have 2 center thru holes and 4
mounting holes.
MONOJACKS ARE CAPTIVATED IN KEYHOLE
SLOT OF HOOD AS SHOWN ABOVE. WHEN
USING SHELLS, MONOJACKS ARE CAPTIVATED
IN KEYHOLE OF SHELL AND CLEARANCE HOLES
ARE PLACED IN HOODS.
Winchester/Retconn
MOLDINGS HAVE STRAIGHT THRU HOLES
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 6
Rack & Panel
Miniature Rectangular, Removable Contacts
MRAC Series
OUTLINE
JACKSCREW & JACKSOCKETS
Dimensions are for reference only and are subject to change. Outline drawings on request.
.19 Dia.
.22 Dia.
.22
Dia.
.50
.078 INT. HEX.
.25
HEX.
A
A
A
A
JTCW
JTCU
JTCX
.19 Dia.
JTCZ
.22 Dia.
.078 INT. HEX.
.25 HEX.
1
.78
.36
JTW
JTU
JTX
6-32 UNC 2 THD.
(Typ.)
.80 Typ.
.16 Typ.
6-32 UNC 2 THD.
JZ
DIMENSIONS
All jackscrews and sockets are stainless steel, passivated except J & JTD which are nickel plated brass.
All knobs are aluminum, anodized except JTW and JTCW which are stainless steel, passivated.
Hood Type
Size
9
14
18
20
26
34
41
42
50
66
75
Type JTCW
H H1 H8 H9 H13
Dimension A
– 2.22 –
–
– 2.22 –
–
– 2.22 –
–
– 2.22 – 2.22
2.22 2.22 2.22 2.22
2.22 2.22 2.22 2.22
2.22 2.22 –
–
2.22 2.22 2.22 2.22
2.22 2.22 2.22 2.22
2.22 –
– 2.22
2.22 2.22 2.22 2.22
2.22
2.22
2.22
2.22
–
–
–
–
–
–
–
Type JTCU
Size
9
14
18
20
26
34
41
42
50
66
75
H H1 H8 H9 H13
Dimension A
– 2.47 –
–
– 2.47 –
–
– 2.47 –
–
– 2.47 – 2.47
2.47 2.47 2.47 2.47
2.47 2.47 2.47 2.47
2.47 2.47 –
–
2.47 2.47 2.47 2.47
2.47 2.47 2.47 2.47
2.47 –
– 2.47
2.47 2.47 2.47 2.47
2.47
2.47
2.47
2.47
–
–
–
–
–
–
–
Size
9
14
18
20
26
34
41
42
50
66
75
Type JTCX
H H1 H8 H9 H13
Dimension A
– 2.34 –
–
– 2.34 –
–
– 2.34 –
–
– 2.34 – 2.34
2.61 2.34 2.34 2.34
2.34 2.34 2.34 2.34
2.34 2.34 –
–
2.34 2.34 2.34 2.34
2.34 2.34 2.34 2.34
2.34 –
– 2.34
2.34 2.34 2.34 2.34
2.34
2.34
2.34
2.34
–
–
–
–
–
–
–
Size
9
14
18
20
26
34
41
42
50
66
75
Type JTCZ
H H1 H8 H9 H13
Dimension A
– 2.47 –
–
– 2.47 –
–
– 2.47 –
–
– 2.47 – 2.47
2.73 2.47 2.47 2.47
2.47 2.47 2.47 2.47
2.47 2.47 –
–
2.47 2.47 2.47 2.47
2.47 2.47 2.47 2.47
2.47 –
– 2.47
2.47 2.47 2.47 2.47
2.47
2.47
2.77
2.47
–
–
–
–
–
–
–
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 7
Rack & Panel
Miniature Rectangular, Removable Contacts
MRAC Series
OUTLINE
FORMED ALUMINUM HOODS
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Hoods shown are MRE Hoods for use
with MRAC Connectors
DIMENSIONS
Formed Hoods for MRAC Connectors are
available in top and side opening for most
MRAC Connectors - Deep Drawn Hoods are
available for MRAC 34, MRAC 66 and MRAC
104 connectors ... providing additional strength.
Hoods and cable clamps are of anodized
Top Cable Opening
Code No.
A
MRE9H-13 .28
MRE14H-13 .28
MRE18H-13 .28
MRE20H-13 .28
MRE26H
.28
MRE26H-8 .28
MRE34H
.28
MRE34H-8 .28
MRE41H
.28
MRE42H
.09
MRE42H-8 .09
MRE50H
.09
MRE50H-8 .09
MRE75H
.09
MRE75H-8 .09
Side Cable Opening
DIMENSIONS
B
1.28
1.28
1.28
1.28
1.28
1.28
1.25
1.25
1.25
1.30
1.30
1.30
1.30
1.31
1.31
C
1.58
1.58
1.78
1.58
1.72
1.78
1.69
1.75
1.69
1.73
1.80
1.73
1.80
1.75
1.86
aluminum. They provide support and strain
relief for the cable and may be applied to either
Plug or Receptacle.
Hoods may be ordered separately (see code
numbers in the tables below) or assembled on
connectors.
D
1.31
1.25
1.31
1.56
1.63
1.63
2
2
2.63
2.31
2.31
2.59
2.59
2.59
2.59
Cable
Opening Wt.
E
.44
.5
.63
.5
.64
.64
.83
.83
.5
.83
.83
.83
.83
1.19
1.19
F
.59
.59
.61
.66
.59
.78
.66D
1.06
.66
.63D
1.06
.63D
1.06
.63
1
G
.31
.38
.44
.38
.38
.44
–
.56
.44
–
.56
–
.56
.88
.88
Oz.
.3
.3
.3
.3
.4
.4
.6
.6
.6
.7
.7
.8
.8
1.0
1.0
Fits
Connector
MRAC9 (P or S)
MRAC14 (P or S)
MRAC18 (P or S)
MRAC20 (P or S)
MRAC26 (P or S)
MRAC34 (P or S)
MRAC41 (P or S)
MRAC42 (P or S)
MRAC50 (P or S)
MRAC75 (P or S)
Code
No.
MRE9H-1
MRE9H-9
MRE14H-1
MRE14H-9
MRE18H-1
MRE18H-9
MRE20H-1
MRE20H-9
MRE26H-1
MRE26H-9
MRE34H-1
MRE34H-9
MRE41H-1
MRE42H-1
MRE42H-9
MRE50H-1
MRE50H-9
MRE75H-1
MRE75H-9
DIMENSIONS
A
.28
.28
.28
.28
.28
.28
.28
.28
.28
.28
.28
.28
.28
.09
.09
.09
.09
.09
.09
B
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.25
1.25
1.25
1.30
1.30
1.30
1.30
1.31
1.31
C
1.63
1.61
1.69
1.55
1.75
1.81
2
1.86
2.06
2.13
2.42
–
3.06
2.73
–
3.02
–
3.02
–
D
1.31
1.31
1.25
1.25
1.31
1.31
1.56
1.56
1.63
1.63
2
2
2.63
2.31
2.31
2.59
2.59
2.59
2.59
E
.44
.44
.5
.5
.63
.63
.5
.5
.64
.64
.83
.83
.5
.83
.83
.83
.83
1.19
1.19
Cable
Opening Wt.
F
.31D
.59
.38D
.59
.44D
.69
.38D
.66
.59
.78
.66D
.81
.66
.63
.84
.63
1.06
.63
1
G
–
.31
–
.38
–
.44
–
.38
.38
.44
–
.56
.44
.5
.56
.5
.56
.88
.88
Oz.
.3
.3
.3
.3
.3
.3
.3
.3
.4
.4
.6
.6
.6
.7
.7
.8
.8
1.0
1.0
Fits
Connector
MRAC9 (P or S)
MRAC14 (P or S)
MRAC18 (P or S)
MRAC20 (P or S)
MRAC26 (P or S)
MRAC34 (P or S)
MRAC41 (P or S)
MRAC42 (P or S)
MRAC50 (P or S)
MRAC75 (P or S)
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 8
Rack & Panel
Miniature Rectangular, Removable Contacts
MRAC Series
Lock Tabs (MRE-V shown)
VIBRATION LOCKS
Nomenclature
Lever
Lock Tabs
Used on
& Pilot (See Note) Connectors
Assembly
MRE-VL
MRE-V
MRE-VL2
MRE-V2
MRAC 9, 14,
18, 20, 26, 34,
41, and 42
MRAC 50
MRAC 75
DIMENSIONS / OUTLINE
DRAWN ALUMINUM HOODS
Lever & Pivot Assemblies (MRE-VL shown)
Designed for MRAC connectors, this vibration
lock features genuine simplicity of design, plus
complete locking effectiveness. Assembly of
either the lever-and-pivot assembly or the lock
parts to the plug and receptacle is quick and easy.
The unit locks automatically when the mating plug
and receptacle are engaged. Unlocking and
disengaging can be done with one hand.
Note 1:When panel mounting the lock-tab half of a MRAC 34, MRAC 42 or MRAC 50 connector, flat washers
(.033 minimum thickness) should be used on the mounting screws to shim the molding away from the panel.
Note 2: Each code number indicates two units, i.e., the “MRE-VL” consists of two levers and two pivots
(unassembled*), and the “MRE-V” consists of two tabs.
Note 3: These units are supplied unassembled to facilitate handling. The pivot is easily assembled to the
lever merely by inserting the hooked end through the lever opening. It will automatically snap into proper
position. Patent #2,760,174.
Hoods shown are MRA Hoods for use with MRAC Connectors
Wt.
DIMENSIONS - Top Opening
Fits
Oz. Connector
A
B
C
D
E
H G
MRA 34H-491 2.08 .83 1.17 1.59 .66 x .75 – 1.688 .6 MRAC 34P
Wt.
DIMENSIONS - Side Opening
Fits
Oz. Connector
A
B
C
D
E
H
G
MRA 34H9-491 2.08 .83 1.17 2.59 .64 x .75 1.06 1.688 .6 MRAC 34P
MRA 66H
2.38 1.22 1.17 1.69 1.03 Dia. – 1.969 .8
MRA 66H9
2.38 1.22 1.17 2.92 .84 Dia. 1.34 1.969 .8 MRAC 66S
MRA 104H
2.84 1.63 2.23 2.75 1.19 Dia. – 2.375 1.0
MRA 104H9
2.84 1.63 2.23 3.39 1.19 Dia. 1.63 2.375 1.0 MRAC 104S
Code No.
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Code No.
MRAC 34S
MRAC 66P
MRAC 66S
MRAC 104P
MRAC 104S
MRAC 104P
.1935 Dia. 2 Holes
(.228 Dia. 2 Holes For 104)
For MRA;
66;104
D
C
.08
MRAC 34S
MRAC 66P
H
B
G
E
Cable
Opening
G
A
D
E
Cable
Opening
C
DIMENSIONS / OUTLINE
MOUNTING BRACKETS
B
.08
Top Cable Opening
.08
For MRA 34 Only
H
F
A
B
G
E
C
2.625
D
Code No.
A
B
C
DIMENSIONS
D E
F
G
A
Side Cable Opening
H
Wt.
Oz.
MRE 50B 1.06 .688 3.031 3.44 .13
.28
.78
.128 Dia 3 Holes
(No. 4 Mounting
Screw)
.4
MRE 75B 1.48 1.047 3.062 3.56 .14
.30 1.14
.150 Dia 3 Holes
(No. 6 Mounting
Screw)
.6
Panel
Opening
MRAC 50 and MRAC 75 connectors
use the standard MRE 50 and
MRE 75 mounting brackets.
.11R
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 9
Rack & Panel
Miniature Rectangular, Removable Contacts
MRAC Series
ORDERING INFORMATION
Omit steps not required
MRAC
■ Step 1
Series:
MRAC
MNAC
Numerical
contact
identification
on sizes 34,
50, and 104.
■ Step 2
Number of
Contacts:
9, 14, 18, 20,
26, 34, 41,
42, 50, 66,
75, 104
See note 1
below.
34
■ Step 3
■ Step 4
Contact
Designation:
P - Pin
S - Socket
When ordering
moldings less
hardware to be
used with
monojacks, see
note 2 below.
Guides and
Jackscrew
Locks:
(See bottom
Chart)
S
G
H
■ Step 5
Hoods:
H - Standard top opening.
Sizes 26 thru 104 only.
H1 - Standard side opening.
Available all sizes.
H8 - Large top opening.
Sizes 26 thru 104 only.
H9 - Large side opening.
Available all sizes.
H13 - Large top opening,
high hood. Sizes 9, 14,
18 & 20 only.
■ Step 4
Guides
G*
Phosphor Bronze Cylindrical Guides
K
Beryllium Copper Cylindrical Guides
N*
Brass Cylindrical Guides
Guides are not recommended for Size 104
“P” indicates two guide pins or two jackscrews
(EX. JTCP)
“S” indicates two guide sockets or two jacksockets
(Ex. GS)
Jackscrew Locks
***J
Polarized Fixed Jackscrew and Jacksocket
JT
Polarized Short Turning Jackscrew and
Jacksocket
JTC
Polarized Long Turning Jackscrew and
Jacksocket
*** JTD Polarized Long Turning Mono-Jackscrew and
Mono-Jacksocket for Sizes 34, 42, 50, 66,
75, and 104 only.
** JZ
** JTW
** JTU
** JTX
** JTCW
** JTCU
** JTCX
** JTCZ
VL
■ Step 6
■ Step 7
Vibration Locks:
V - Lock Tab
V2 - Lock Tab
(Size 50
& 75)
VL - Lever & Pivot
Ass’y
VL2 - Lever & Pivot
Ass’y (Size
50 & 75)
Special
Options:
Consult Sales
Department
Same as J but with 6-32 mtg. thd. (Std. on
104)
Same as JT but with knurled round knob
with internal hex (not avail. 104)
Same as JT but with knurled round knob
with screwdriver slot (not avail. 104)
Same as JT but with hex knob (not avail.
104)
Same as JTC but with knurled round knob
with internal hex (not avail. 104)
Same as JTC but with knurled round knob
with screwdriver slot (not avail. 104)
Same as JTC but with hex knob (not avail.
104)
Same as JTC but with prybar knob (not
avail. 104)
* For passivated stainless steel add SS suffix.
** Request availablity information.
*** Material: Nickel Plated Brass standard
Notes: 1. Contacts are ordered separately. See 100 Series contact section of Rack & Panel
2. When ordering molding less hardware and hood for use with JTD Monojacks, connectors
must be ordered as follows:
Pin connector = MRAC 34P8, MRAC 42P8, etc.
Socket connector = MRAC 34S8, MRAC 42S8, etc.
The number “8” indicates special housing for use with the JTD Monojack hardware
(available on sizes 34, 42, 50, 66, 75 and 104).
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 10
Rack & Panel
External Miniature Rectangular, Removable Contacts
XAC Series
XAC34SF2A010
XAC34PM1A000
XAC34PC1A700
Designed for external installation, the XAC is
the MRAC removable contact connector
equipped with protective shells and mounting
plates for chassis or cable mounting on metal
containers, bulkheads, or any outside surface
equipment. Lighter and smaller than other
external connectors, they provide dependable
service under adverse conditions. Inserts are
housed in protective shells and there is screw
lock coupling of plug and receptacle.
Current Rating: Up to 13 amps
No. of
Contacts:
9, 14, 18, 20, 26, 34, 42, 50,
66, 75, 104
Contacts:
Contacts must be ordered
separately. Select from
crimp, solder, dip solder,
shielded or wire wrap
terminations.
Electrical Data: Meets high potential
performance requirements of
MIL-C-28748. The dielectric
withstanding voltage is one
minute electrification at
2000 VAC.
Military versions are QPL’d to
M28748/3 and M28748/4.
Dielectric:
SPECIFICATIONS
CATALOG NO.
Winchester/Retconn
XAC9-0300X
XAC14-0300X
XAC20-0300X
XMRE9-0400X
XMRE14-0400X
XMRE20-0400X
XMRE26-0300X
XMRE26-0400X
XMRE34-0300X
XMRE34-0400X
XMRE42-0300X
XMRE42-0400X
XMRE50-0300X
XMRE50-0400X
XMRE75-0300XP
XMRE75-0300XS
Polarization:
Accessories:
CATALOG NO.
MS 18192-T8
MS 18192-T1
MS 18192-T2
MS 18192-S8
MS 18192-S1
MS 18192-S2
MS18192-T9
MS 18192-S9
MS18192-T3
MS 18192-S3
MS 18192-T4
MS 18192-S4
MS18192-T5
MS 18192-S5
MS 18192-T6
MS 18192-TXX
XMRE75-0400XS
XMRE75-0400XP
XMRA66-0700
XMRA66-0800
XMRA 104-0700
XMRA 104-0800
XJTCMS605P
XJTCMS605S
XJTCMS608P
XJTCMS608S
XJTMS605P
XJTMS605S
XJTMS606P
XJTMS606S
XJMS602P
XJMS602S
Diallyl Phthalate, MIL-M-14,
Type SDG-F, Color Gray
Seven positions available for
pin and slot polarization on
shells. Additional polarization can be provided with
various arrangements of
jackscrews and guides.
Shells, formed and drawn
hoods, mounting plates,
jackscrews and jacksockets.
CATALOG NO.
MS 18192SXX
MS 18192-S6
MS 18193-T1
MS 18193-S1
MS 18193-T2
MS 18193-S2
MS 18194-1
MS 18194-2
MS 18194-3
MS 18194-4
MS 18195-1
MS 18195-2
MS 18195-3
MS 18195-4
MS 18196-1
MS 18196-2
XJMS603P
XJMS603S
XNMS700P
XNMS700S
XNMS702P
XNMS702-S
XMRA 14-0010
XMRA 20-0010
XMRA 34-0010
XMRA42-0010
XMRA50-0010
XMRA75-0010
XMRA66-0010
XMRA104-0010
MS 18196-3
MS 18196-4
MS 18197-1
MS 18197-2
MS 18197-3
MS 18197-4
MS 18198-1
MS 18198-2
MS 18199-1
MS 18199-2
MS 18199-3
MS 18199-4
MS 18200-1
MS 18200-2
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 11
Rack & Panel
External Miniature Rectangular, Removable Contacts
XAC Series
CONNECTOR ASSEMBLIES
Self-locking
pins
Turnable
Jacksocket
Plug Shell
Jackscrew
and
Jacksocket
Knobs
Male Insert
Turnable
Jackscrew
Fixed
Jackscrew
Mounting Plate
Receptacle Shell
Female Insert
Fixed
Jacksocket
Receptacle
DEFINITIONS OF
CONNECTOR TERMS
Plug: The complete connector half which
has the plug shell as part of its assembly.
Receptacle: The complete connector half
which has the receptacle shell as part of its
assembly.
Shell: The metal housing in which a male or
female insert is assembled. A shell is either a
plug shell or a receptacle shell:
Plug Shell - one which is designed to be
inserted into a receptacle shell.
Receptacle Shell - one which is designed
to receive and enclose the plug shell upon
engagement.
Male Insert: The molded insulator body
containing pin contacts.
Female Insert: The molded insulator body
containing socket contacts.
Pin Contacts: Male Contacts that fit into the
socket contacts.
Socket Contacts: Female Contacts tubular
in shape, which receive the pin contacts and
retain them by spring tension.
Polarization: A means of controlling the
engagement of a plug and receptacle so that
correct mating of the contacts is achieved.
Accessories: Those components such as
hoods and mounting plates which are
attachable to a plug or receptacle to facilitate
mounting and/or handling of the connector,
and to prevent inadvertent cross-mating.
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 12
Rack & Panel
External Miniature Rectangular, Removable Contacts
XAC Series
CONTACT ARRANGEMENTS
Dimensions are for reference only and are subject to change. Outline drawings on request.
Views are rear (wiring end) of female inserts. (Male inserts are opposite.)
.44
.38
.44
.56
.22
.075
Typ
.075
Typ
.075
Typ
.075
Typ
1.250
1.313
.937
1.313
1.000
1.563
1.000
1.250
.09R
.09R
.09R
.13R
.130 Typ
.172 Typ
XAC 9
XAC 14
.56
.75
.075
Typ
.23
.13R
.130 Typ
XAC 18
XAC 20
.75
.47
.23
.47
.075
Typ
.09R
.13R
.130 Typ
.075
Typ
.09R
.88
.09R
.075
Typ
.23
.75
.47
.23
1.625
2.594
2.000
2.313
1.312
1.688
2.282
2.719
2.000
.09R
Mounting
Holes For
No. 4
Machine
Screws
Mounting
Holes For
No. 4
Machine
Screws
.13R
.150
Typ
1.125
.50
.25
.73
.180 Typ
.130 Typ
XAC 26
Mounting
Holes For
No. 4
Machine
Screws
.180 Typ
XAC 34*
XAC 42
1.234
1.109
.77
.23
1.531
.16R
.73
.180 Typ
XAC 50*
.88
.075
Typ
.075
Typ
.44
2.750
2.719
2.281
2.282
1.969
Mounting
Holes For
No. 4
Machine
Screws
1.109
.31R
Mounting
Holes For
No. 4
Machine
Screws
1.094
.180 Typ
XAC 66
Winchester/Retconn
2.375
2.594
XAC 75
.16R
.180 Typ
Mounting
Holes For
No. 6
Machine
Screws
1.469
.38R
.180 Typ
XAC 104*
*For numerical contact identification instead of alphabetical, order XNAC**P or S available in
sizes 34, 50, and 104.
Sizes 66 and 75 have numerical contact identification as standard.
The spacing, arrangement, and identificaion of contacts of the XAC inserts are the same as those
found on the Series MRAC removable contact connectors for the same number of contacts.
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 13
Rack & Panel
External Miniature Rectangular, Removable Contacts
XAC Series
JACKSCREW & JACKSOCKETS
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Views are rear (wiring end)
of female inserts. (Male
inserts are opposite.)
.73
Fixed Jackscrews (F)
Long Turning Jackscrews (C)
Used With Hoods
Short Turning Jackscrews (M)
Used Only Without Hoods
Monojacks (D)
Used With Hoods
SPECIFICATIONS
Turnable jackscrew-jacksocket combination (M,
C, or D) assembles on either Plug or Receptacle; the mating connector-half (either
Receptacle or Plug) must then contain fixed
jackscrew-jacksocket combination (F).
Monojacks (D) are long turning one-peice
locking devices with slotted and knurled head.
Shaft has through-hole for safety wire.
available with hoods only, in sizes 34, 42, 50,
66, 75, and 104.
Both short and long turning jackscrews (M and C)
have knurled and slotted knobs for locking by
hand or screwdriver. Knob is assembled on shaft
with hollow, removable, self-locking pin. Safety
wiring of engaged halves is achieved by using
the through-hole in self-locking pin in the knob.
Drawings show extension of standard knobs
beyond shell and beyond hood.
APPLICATIONS
Jackscrew locking device assures positive
coupling of engaged connectors to prevent
accidental disconnecting from vibration or
physical shock. It also aids easy connection
and separation of connector plug and
LOCKING DEVICE
receptacle. Mounted connector-half houses
one non-turnable fixed jackscrew and
jacksocket to insure connector polarization.
Mating-half houses one of the three types of
turning jackscrew and jacksocket (M, C, or D).
SPECIFICATIONS
WT. OZ.
CODE See Notes MATERIAL AND
LETTER
1&2
FINISH
Jackscrew
Fixed
Jacksocket }
Jackscrew
Short
Jacksocket }Turnable
Jackscrew
Long
Jacksocket }Turnable
Mono-Jackscrew
Long Turnable
Mono-Jacksocket
Knob Standard
Nickel Plated Brass
F
0.15
M
0.30
C
0.45
D
1.07
Nickel Plated Brass
—
—
Aluminum Anodized
Stainless Steel with
Passivating Dip
Stainless Steel with
Passivating Dip
Note 1: Weights are for pairs; i.e. for a
jackscrew and jacksocket, etc., so
weight figure may be added once to
weights of other accessories when
computing total weight of plug or
receptacle.
Note 2: Weights of turnable jackscrews and turnable jacksockets
include knob and rollpins, except
mono-jackscrew and mono-jacksocket,
which is a one-piece construction (shaft
and knob made in one piece); weight of
fixed jackscrew and jacksocket
includes nuts.
DIMENSIONS
Standard Knobs - Extension
Beyond Hood
XAC
Dimension A
Dimension B
9* 14* 18* 20* 26 34 42 50 66 75 104 34 42 50 66 75 104
0300
0400
0700
0800
.55
.55
–
–
.55
.55
–
–
.55
.55
–
–
.55
.55
–
–
.77
.55
–
–
.58
.58
.58
.58
.53
.53
–
–
.53
.53
–
–
–
–
.64
.64
.52
.52
–
–
– .59 .55 .55 –
– .59 .55 .55 –
.52 – – – .38
.52 – – – .38
.53
.53
–
–
–
–
.38
.38
*On sizes 9, 14, 18, and 20, only large top opening hoods are available when (c) long turning jackscrews are used.
Catalog Number for large top opening hoods is - 0300X. Example: XAC20-0300X
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 14
Rack & Panel
External Miniature Rectangular, Removable Contacts
XAC Series
OUTLINE - JACKSCREWS
.19 Dia.
.50
.22
Dia.
.078 INT. HEX.
.22
Dia.
.25
HEX.
A
A
A
A
CW
CU
CX
CZ
.19
Dia.
.22
Dia.
.97
.33
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
MW
MU
.25 HEX.
6-32 UNC 2 THD. (TYP.)
.73
.23
MX
FZ
DIMENSIONS
All jackscrews and sockets are stainless
steel, passivated (except F & D which
are nickel plated brass). All knobs are
aluminum, anodized except MW and CW
which are stainless steel, passivated.
Size
9
14
18
20
26
34
42
50
66
75
9
14
18
20
26
34
42
50
66
75
Hoods
Hoods
Size
0300 0400 0300X 0400X 0700 0800
0300 0400 0300X 0400X 0700 0800
Dimension A – Type CW
.36
.36
.36
–
.36
.36
.36
–
.36
.36
.36
–
.36
.36
.36
–
.36
.36
.36
–
.39
.39
.39
.47
.34
.34
.34
–
.34
.34
.34
–
–
–
–
.47
.33
.33
.33
–
Dimension A – Type CU
–
.61
.61
.61
–
–
.61
.61
.61
–
–
.61
.61
.61
–
–
.61
.61
.61
–
.61 .61
.61
.61
–
.64 .64
.64
.64
.72
.59 .59
.59
.59
–
.59 .59
.59
.59
–
–
–
–
–
.72
.58 .58
.58
.58
–
–
–
–
–
.36
.39
.34
.34
–
.33
–
–
–
–
–
.47
–
–
.47
–
9
14
18
20
26
34
42
50
66
75
–
–
–
–
.77
.52
.47
.47
–
.45
–
–
–
–
–
.72
–
–
.72
–
9
14
18
20
26
34
42
50
66
75
–
–
–
–
.92
.64
.59
.59
–
.58
Dimension A – Type CX
.48
.48
.48
–
.48
.48
.48
–
.48
.48
.48
–
.48
.48
.48
–
.48
.48
.48
–
.52
.52
.52
.61
.47
.47
.47
–
.47
.47
.47
–
–
–
–
.61
.45
.45
.45
–
Dimension A – Type CZ
.61
.61
.61
–
.61
.61
.61
–
.61
.61
.61
–
.61
.61
.61
–
.61
.61
.61
–
.64
.64
.64
.72
.59
.59
.59
–
.59
.59
.59
–
–
–
–
.72
.58
.58
.58
–
–
–
–
–
–
.61
–
–
.61
–
–
–
–
–
–
.72
–
–
.72
–
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 15
Rack & Panel
XAC Series
External Miniature Rectangular, Removable Contacts
OUTLINE
HOODS - DRAWN ALUMINUM
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
The XAC Series uses standard XMRA/
XMRE protective hardware. To order
separately, use XMRE/XMRA catalog
numbers indicated.
.08
.08
Top Cable Opening
.08
Side Cable Opening
DIMENSIONS
XMRA Drawn Hoods for use with
XAC Connectors.
Hoods - Side Cable Opening
ForUse
With
Hood
Part No.
(If ordered
separately)
Type C Jack XMRA 34-0800
Sockets and
XMRA 66-0800
Jackscrews
A
B
DIMENSIONS
C
D
E
F
G
2.09 .84
2.38 1.22
2.84 1.63
1.17 2.58 .64x.75 1.688 1.06
1.17 2.91 .84D 1.969 1.34
2.23 3.38 1.19D 2.375 1.63
2.09 .84
Type D Jack XMRA 34-0800D
Sockets and XMRA 66-0800D
2.38 1.22
Jackscrews XMRA 104-0800D 2.84 1.63
1.17 2.58 .64x.75 1.688 1.06
1.17 2.91 .84D 1.969 1.34
2.23 3.38 1.19D 2.375 1.63
XMRA 104-0800
Type F
Jackscrews
XMRA 34-0200
XMRA 66-0200
XMRA 104-0200
2.09 .84
2.38 1.22
2.84 1.63
1.17 2.58 .64x.75
1.17 2.91 .84D
2.23 3.38 1.19D
–
–
–
DIMENSIONS
C
D
E
F
1.06
1.34
1.63
Hoods - Top Cable Opening
ForUse
With
Hood
Part No.
(If ordered
separately)
Type C Jack XMRA 34-0700
Sockets and
XMRA 66-0700
Jackscrews
A
B
2.09 .84
2.38 1.22
2.84 1.63
1.17 1.59 .66x.75 1.688
1.17 1.69 1.03D 1.969
2.23 2.75 1.19D 2.375
2.09 .84
Type D Jack XMRA 34-0700D
Sockets and XMRA 66-0700D
2.38 1.22
Jackscrews XMRA 104-0700D 2.84 1.63
1.17 1.59 .66x.75 1.688
1.17 1.69 1.03D 1.969
2.23 2.75 1.19D 2.375
XMRA 104-0700
Type F
Jackscrews
XMRA 34-0900
XMRA 66-0900
XMRA 104-0900
2.09 .84
2.38 1.22
2.84 1.63
1.17 1.59 .66x.75
1.17 1.69 1.03D
2.23 2.75 1.19D
–
–
–
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 16
Rack & Panel
XAC Series
External Miniature Rectangular, Removable Contacts
OUTLINE
HOODS - FORMED ALUMINUM
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Top Cable Opening
Large Top Cable Opening
Side Cable Opening
DIMENSIONS
XMRE Formed Hoods for use
with XAC Connectors
Hoods - Top Cable Opening
For use
with
Monojacks
XMRE 34-0300D
XMRE 34-0300XD
XMRE 42-0300D
XMRE 42-0300XD
XMRE 50-0300D
XMRE 50-0300XD
XMRE 75-0300D
XMRE 75-0300XD
For use with
Type C
Jacksockets &
Jackscrews
Hood Part No.
For use with
Fixed
Jackscrews*
A
B
C
D
E
Dia.
F
Dia.
1.28
1.28
1.28
1.28
1.28
1.28
1.25
1.25
1.30
1.30
1.30
1.30
1.31
1.31
1.31
1.25
1.31
1.56
1.63
1.63
2
2
2.31
2.31
2.59
2.59
2.59
2.59
1.58
1.58
1.78
1.58
1.72
1.78
1.69
1.75
1.73
1.80
1.73
1.80
1.75
1.86
.44
.50
.63
.50
.64
.64
.83
.83
.83
.83
.83
.83
1.19
1.19
.59
.59
.61
.66
.59
.78
.66
1.06
.63
1.06
.63
1.06
.63
1
.31
.38
.44
.38
.38
.44
–
.56
–
.56
–
.56
.88
.88
(If ordered separately)
XAC 9-0300X
XAC 14-0300X
XAC 18-0300X
XAC 20-0300X
XMRE 26-0300
XMRE 26-0300X
XMRE 34-0300
XMRE 34-0300X
XMRE 42-0300
XMRE 42-0300X
XMRE 50-0300
XMRE 50-0300X
XMRE 75-0300
XMRE 75-0300X
XAC 9-0500XJ
XAC 14-0500XJ
XAC 18-0500XJ
XAC 20-0500XJ
XMRE 26-0500J
XMRE 26-0500XJ
XMRE 34-0500J
XMRE 34-0500XJ
XMRE 42-0500J
XMRE 42-0500XJ
XMRE 50-0500J
XMRE 50-0500XJ
XMRE 75-0500J
XMRE 75-0500XJ
Cable
Opening
Dimensions
Wt.
Oz.
(Inc. 2
Cable
Clamps
and
Screws)
0.3
0.3
0.4
0.3
0.4
0.6
0.7
0.8
1.0
* For use with G, K, or N guides, eliminate letter “J” from part number
Hoods - Side Cable Opening
For use
with
Monojacks
XMRE 34-0400D
XMRE 34-0400XD
XMRE 42-0400D
XMRE 42-0400XD
XMRE 50-0400D
XMRE 50-0400XD
XMRE 75-0400D
XMRE 75-0400XD
For use with
Type C
Jacksockets &
Jackscrews
Hood Part No.
For use with
Fixed
Jackscrews*
A
B
C
D
E
Dia.
F
Dia.
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.25
1.25
1.30
1.30
1.30
1.30
1.31
1.31
1.31
1.31
1.25
1.25
1.31
1.31
1.56
1.56
1.63
1.63
2
2
2.31
2.31
2.59
2.59
2.59
2.59
1.63
1.61
1.69
1.55
1.75
1.81
2
1.86
2.06
2.13
2.42
2.50
2.73
2.81
3.02
3.09
3.02
3.14
.44
.44
.5
.5
.38
.38
.5
.5
.64
.64
.83
.83
.83
.83
.83
.83
1.19
1.19
.31
.59
.38
.59
.44
.69
.38
.66
.59
.78
.66
.81
.63
.84
.63
1.06
.63
1
–
.31
–
.38
–
.44
–
.38
.38
.44
–
.56
.5
.56
.5
.56
.88
.88
(If ordered separately)
XMRE 9-0400
XMRE 9-0400X
XMRE 14 -0400
XMRE 14-0400X
XMRE 18-0400
XMRE 18-0400X
XMRE 20-0400
XMRE 20-0400X
XMRE 26-0400
XMRE 26-0400X
XMRE 34-0400
XMRE 34-0400X
XMRE 42-0400
XMRE 42-0400X
XMRE 50-0400
XMRE 50-0400X
XMRE 75-0400
XMRE 75-0400X
XMRE 9-0600J
XMRE 9-0600XJ
XMRE 14-0600J
XMRE 14-0600XJ
XMRE 18-0600J
XMRE 18-0600XJ
XMRE 20-0600J
XMRE 20-0600XJ
XMRE 26-0600J
XMRE 26-0600XJ
XMRE 34-0600J
XMRE 34-0600XJ
XMRE 42-0600J
XMRE 42-0600XJ
XMRE 50-0600J
XMRE 50-0600XJ
XMRE 75-0600J
XMRE 75-0600XJ
Cable
Opening
Dimensions
Wt.
Oz.
(Inc. 2
Cable
Clamps
and
Screws)
0.3
0.3
0.4
0.3
0.4
0.6
0.7
0.8
1.0
* For use with G, K, or N guides, eliminate letter “J” from part number
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 17
Rack & Panel
External Miniature Rectangular, Removable Contacts
XAC Series
OUTLINE
SHELLS - RECEPTACLES
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.03R
.06R
B
C
..140 Dia.
4 Holes
B
C
B
C
.06R
.14R
Mtg. Hole
Style 9
F
.421 R.
.384 R.
.120 Dia.
B
C
.28
B
C
.20 R.
ED
ED
ED
ED
A
.156 Typ.
ED
.06R
.06R
.06R
.06R
.06R
.312 Typ.
.120 Dia.
2 Holes
Polarizing Slot
For All XAC
Configurations
.14R
For XAC 9 to 26
.120 Dia.
6 Holes
G
.114
G
For XAC 34, 42,
and 50
.120 Dia.
4 Holes
.117
.383
.766
.500
For XAC 66
For XAC 75
G
.150 Dia.
6 Holes
.875
For XAC 104
DIMENSIONS
SHELLS - RECEPTACLES
Important Note When Ordering
Plug and Receptacle Shells
Shell Part No.
The shell part numbers given in the
table show an asterisk (*) where the
code letter for the desired polarizing
position belongs - example:
XMRE9-2*000 becomes XMRE92B000 when polarization in position
“B” is desired. Specify the same
position on the mating shell.
For non-polarized shells, merely
omit this position, e.g. XMRE9-2000.
XMRE 9-2*000
XMRE 14-2*000
XMRE 18-2*000
XMRE 20-2*000
XMRE 26-2*000
XMRE 34-2*000
XMRE 34-4*000
XMRE 42-2*000
XMRE 42-4*000
XMRE 50-2*000
XMRE 50-4*000
XMRA 66-2*000
XMRA 66-4*000
XMRE 75-2*000
XMRE 75-4*000
XMRA 104-2*000
XMRA 104-4*000
TYPICAL SHELLS FOR
MONOJACKS STYLE No. 4000
Shells are .040 in. thick.
Shells are aluminum, anodized for
protection against corrosion. Either
shell style - plug or receptacle - may be
used to house the female insert, thus
allowing the “live” socket contacts to be
cable or panel mounted, as desired.
Shells also provide a means by which
connector polarization is accomplished
- the receptacle shell is slotted for
engaging a polarizing pin on the plug
shell. Any of seven positions (A, B, C,
D, E, F or G) may be specified for
polarization; non-polarized shells have
the slot and pin omitted.
For Connector Size
A
B
(If ordered
separately)
DIMENSIONS
C
D
E
F
G
Wt.
Oz.
.88
.81
.88
1.13
1.19
.66
.66
.66
.66
.66
–
–
–
–
–
0.15
0.16
0.17
0.19
0.23
.75
1.687 1.44
.66
.234
0.25
.89
.75
2.000 1.75
.66
.234
0.28
2.86 1.02
.75
2.282 2.03
.66
.234
0.30
2.42 1.27
1.13 1.969 1.72
.66
.250
0.28
2.86 1.38
1.11 2.282 2.03
.66
–
0.32
2.91 1.69
1.48 2.375 2.13
.66
.437
0.30
A
B
1.45
1.39
1.45
1.70
1.77
.52
.58
.70
.58
.70
.38
.45
.58
.45
.58
1.000
.937
1.000
1.250
1.312
2.14
.89
2.45
C Typ.
A
B Dia.
4 Corner
Holes
2 Slots
A
C Typ.
4 Slots
C
34, 42, 50, 66, 75
.11 .120 .06R
104
.14 .150 .07R
For XAC 34, 42, 50, 66,
and 104 Configurations
Winchester/Retconn
B Dia.
4 Corner
Holes
For XAC 75
Configuration
Receptacle Shell
Style No. 2000
Shells are .040 in. thick.
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 18
Rack & Panel
External Miniature Rectangular, Removable Contacts
XAC SERIES
OUTLINE
SHELLS - PLUGS
Dimensions are for reference only and are subject to change. Outline drawings on request.
B
C
B
C
.06R .03R
.140 Dia.
4 Holes
B
C
.120 Dia.
4 Holes
B
C
.06R
.14R
Mtg. Hole
Style 9
B
C
F
.508
DE
DE
DE
.06R
.06R
DE
DE
.06R
.06R
.06R
A
.156 Typ.
.312 Typ.
.150 Dia.
6 Holes
.421 R.
G
.875
.120 Dia.
4 Holes
For XAC 104
.117
.383
.766
.20 R.
.120 Dia.
6 Holes
.372 R.
G
.500
For XAC 75
.120 Dia.
2 Holes
For XAC 66
The shell part numbers given in the table
shows an asterisk (*) where the code
letter for the desired polarizing position
belongs - example: XMRE9-1*000
becomes XMRE9-1B000 when
polarization in position “B” is desired.
Specify the same position on the mating
shell.
For non-polarized shells, merely omit
this position, e.g. XMRE9-1000.
Shells are .040 in. thick.
Stainless steel shells available for 66 and
104 sizes. Dimensions vary from those
shown for aluminum shells. Check sales
for availability and dimensions on all sizes.
Shell Part No.
(If ordered
separately)
XMRE 9-1*000
XMRE 14-1*000
XMRE 18-1*000
XMRE 20-1*000
XMRE 26-1*000
XMRE 34-1*000
XMRE 34-3*000
XMRE 42-1*000
XMRE 42-3*000
XMRE 50-1*000
XMRE 50-3*000
XMRA 66-1*000
XMRA 66-3*000
XMRE 75-1*000
XMRE 75-3*000
XMRA 104-1*000
XMRA 104-3*000
.14R
For XAC 34, 42,
and 50
DIMENSIONS
Important Note When Ordering
Plug Shells
G
.468
A
B
DIMENSIONS
C
D
E
1.44
1.38
1.44
1.69
1.75
.5
.56
.69
.56
.69
.38
.45
.58
.45
.58
1.000
.937
1.000
1.250
1.312
2.13
.88
2.44
2.84
.120 Dia.
2 Holes
For XAC 75
For XAC 9 to 26
F
G
Wt.
Oz.
.88
.81
.88
1.13
1.19
.63
.63
.63
.63
.63
–
–
–
–
–
0.14
0.15
0.16
0.18
0.22
.75
1.687 1.44
.66
.234
0.24
.88
.75
2.000 1.75
.66
.234
0.26
1
.75
2.282 2.03
.66
.234
0.28
2.41 1.25
1.13 1.969 1.72
.66
.250
0.28
2.84 1.36
1.11 2.282 2.03
.66
–
0.30
2.88 1.66
1.48 2.375 2.13
.66
.437
0.30
Polarizing Pin
For All XAC
Configurations
TYPICAL SHELLS FOR
MONOJACKS STYLE No. 3000
Shells are aluminum, anodized for
protection against corrosion. Either
shell style - plug or receptacle - may be
used to house the female insert, thus
allowing the “live” socket contacts to be
cable or panel mounted, as desired.
Shells also provide a means by which
connector polarization is accomplished
- the receptacle shell is slotted for
engaging a polarizing pin on the plug
shell. Any of seven positions (A, B, C,
D, E, F or G) may be specified for
polarization; non-polarized shells have
the slot and pin omitted.
For Connector Size
A
B
4 Slots
B Dia.
4 Corner
Holes
A
B Dia.
4 Corner
Holes
2 Slots
C Typ.
A
C
34, 42, 50, 66, 75
.11 .120 .06R
104
.14 .150 .07R
Winchester/Retconn
C Typ.
For XAC 75
Configuration
For XAC 34, 42, 50, 66,
and 104 Configurations
Plug Shell
Style No. 1000
Shells are .040 in. thick.
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 19
Rack & Panel
External Miniature Rectangular, Removable Contacts
XAC SERIES
ORDERING INFORMATION
Omit steps not required
XAC
■ Step 1
■ Step 2
Series:
XAC, XNAC
Numerical
contact
identification
on sizes 34,
50, and 104.
No. of
Contacts:
9, 14, 18, 20,
26, 34, 42,
50, 66, 75,
and 104
See note 1
below
■ Step 3
Pin or
Socket
Contacts:
P - Pin
S - Socket
■ Step 4
Jackscrews
(See
bottom
chart)
9
P
M
■ Step 5
■ Step 6
Shell Type:
Polarization
Position:
**
0 No shell
A, B, C, D,
**
1 Plug shell,
E, F or G.
style 1*000.
Omit letter
**
2 Receptacle
when
shell, style
polarization
2*000.
is not
**
3 Plug shell,
required.
monojack
type,
style 3*000.
**
4 Receptacle,
monojack type,
style 4*000.
**
7 Stainless Steel
Plug shell, style
7*000.
**
8 Stainless Steel
Receptacle shell,
style 8*000.
1
■ Step 7
(See
bottom
chart)
A
0
■ Step 8
Mounting Plate:
00- When no
mounting
plate is
required
*10- Mounting
plate, style
#0010.
Note: See section
XMRA/E RP/ 57.
*Mounting plates
are not used with
“M”, “C” or “D”
jackscrews.
00
■ Step 9
Special Gaskets:
Omit letter when gaskets
are not required.
**
G- Bulkhead gasket, style
#0000G. Use only
when mounting plate is
specified.
**
F- Face gasket, style
#0000F. Use with
male insert only.
**
B- If both gasket #0000G
and gasket #0000F
are desired.
**
**
Check plant for availability
on all gaskets.
**
Polarizing Position
Request availability
**
information
**
■ Step 4
Guides
**
G- Cylindrical guide with single spring member.
Recommended for ground only.
**
KCylindrical guide with four spring members.
May be used for electrical contact.
**
NCylindrical guide without spring member.
Recommended for extra mechanical strength.
Jackscrews and Jacksockets
*** M- Polarized short turnable jackscrew and
jacksocket. Cannot be used with hoods.
*** C- Polarized long turnable jackscrew and
jacksocket for use with hoods.
*** D- Polarized one-piece mono-jackscrew and
mono-jacksocket (no separate knob); to be
used with hoods on sizes: 34, 42, 50, 66, 75,
and 104.
***
Polarized fixed jackscrew and jacksocket
***Fusable with or without hood; (no knob
required).
** MW- Same as M but with knurled round knob with
internal hex.
** MU- Same as M but with knurled round knob with
screwdriver slot.
** MX- Same as M but with hex knob.
** CW- Same as C but with knurled round knob with
internal hex.
** CU- Same as C but with knurled round knob with
screwdriver slot.
** CX- Same as C but with hex knob.
** CZ- Same as C but with prybar knob.
■ Step 7
Formed Hoods:
0- No Hood.
3- Hood, top opening, style #0300, for use with Type “C”
or “D” jackscrews.
4- Hood, side opening, style #0400, for use with Type “C”
or “D” jackscrews.
5- Hood, top opening, style #0500J, for use with “F”
style jackscrews.
6- Hood, side opening, style #0600J, for use with “F”
style jackscrews.
Deep Drawn Hoods:
7- Hood, top opening, style #0700, for use with Type “C”
or “D” jackscrews.
8- Hood, side opening, style #0800, for use with Type “C”
or “D” jackscrews.
9- Hood, top opening, style #0900, for use with
“F” jackscrews.
2- Hood, side opening, style #0200, for use with
“F” jackscrews.
Note: Addition of “X” to code # indicates cable opening
larger than std. See hoods for cable opening size.
Example: XAC20PC1A300 X
** Request availability information
*** Material: Nickel Plated Brass standard
Note: 1. Contacts are ordered separately. See 100 Series contact section of Rack & Panel
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 20
Rack & Panel
TMRAC SeriesTM
Heavy Duty, Industrial and Commercial, Miniature
Rectangular Rack & Panel Connectors, Removable Contacts
Removable contacts offer a substantial savings
of time, labor and a great flexibility in the choice
of circuitry. The contact is easily removed with
the hand tool depicted and then placed by
hand or with a simple insertion tool.
TMRAC 34S-G
TMRAC 34P-G
The TMRAC Series was designed specifically for the industrial/ commercial
customer for application in high temperature, rough service operations. This series
features the same military-type anodized aluminum hoods, rugged polyester
thermoplastic insulators, screw-machine removable contacts, guide and hardware
as the MRAC Series.
SPECIFICATIONS
Insulators:
Polyester thermoplastic,
black color. High potential
performance: withstanding
voltage is one minute
electrification at 2000 VAC
(sea level).
Insulation
Resistance:
500V
Thermal Shock: -55oF to +150oF
Hoods:
Anodized aluminum. May be
applied on plug or receptable.
Both top and side opening
hoods available.
Polarization: Gold plated guides provide
positive polorization.
Polarized nickel-plated brass
and/or passivated stainless
steel jackscrews with
anodized aluminum knobs
are available.
Number of
Contacts:
Eight size connectors: 9-, 14-,
18-, 20-, 26-, 34-, 42- and
50-contact, available in either
.040" or .062" diameter.
Contacts:
Must be ordered separately.
Select from crimp, solder, dip
solder, shielded or Wire-Wrap
termination contacts. See 100
Series contact section.
Contact
Identification: Standard contact identification
is alphabetical.
Sizes:
.040" diameter and .062"
diameter contacts in 7.5-amp
and 13-amp current ratings.
Termination
Types:
Crimp, dip-solder, solder
removable in .040" and .062"
diameter. Wire Wrap tails and
stabilizing bushings for .025"
and .045" square.
Current Rating: 7.5 amps maximum for
.040" contacts.
13 amps maximum for
.062" contacts.
®
CSA Certified File No.
LR34182
Recognized under the Component Program
of Underwriters Laboratories Inc. File No. E31650 ®
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 21
Rack & Panel
Heavy Duty, Industrial and Commercial, Miniature
Rectangular Rack & Panel Connectors, Removable Contacts
TMRAC SeriesTM
ORDERING INFORMATION
Omit steps not required
TMRAC
34
S
G
H
VL
■ Step 1
■ Step 2
■ Step 3
■ Step 4
■ Step 5
■ Step 6
■ Step 7
Insert Series
Code:
TMRAC
Number of
Contacts:
9, 14, 18,
20, 26, 34,
42, 50,
See note 1
below.
Contact
Designation:
P - Pin
S - Socket
When
ordering
moldings less
hardware for
use with
mono-jacks,
see note 2
below.
Guides and
Jackscrew
Locks:
(See bottom
Chart)
Hoods:
H - Standard top opening.
Sizes 26, 34, 42 &
50 only.
H1 - Standard side opening.
Available all sizes.
H8 - Large top opening.
Sizes 26, 34, 42 &
50 only.
H9 - Large side opening.
Available all sizes.
H13 - Large top opening,
high hood. Sizes 9, 14,
18 & 20 only.
Vibration
Locks:
V - Lock Tab
V2 - Lock Tab
(Size 50)
VL - Lever &
Pivot Ass’y
VL2- Lever &
Pivot Ass’y
(Size 50)
Special
Options:
Consult Sales
Department
■ Step 4
Guides
G*
Phosphor Bronze Cylindrical Guides
K
Beryllium Copper Cylindrical Guides
N*
Brass Cylindrical Guides
“P” indicates two guide pins or two jackscrews
(EX. JTCP)
“S” indicates two guide sockets or two jacksockets
(Ex. GS)
* For passivated stainless steel add SS suffix.
Jackscrew Locks
***J
Polarized Fixed Jackscrew and Jacksocket
JT
Polarized Short Turning Jackscrew and
Jacksocket
JTC
Polarized Long Turning Jackscrew and
Jacksocket
*** JTD Polarized Long Turning Mono-Jackscrew and
Mono-Jacksocket for Sizes 34, 42, and
50 only.
** JZ
** JTW
** JTU
** JTX
** JTCW
** JTCU
** JTCX
** JTCZ
Same as J but with 6-32 mtg. thd.
Same as JT but with knurled round knob
with internal hex
Same as JT but with knurled round knob
with screwdriver slot
Same as JT but with hex knob
Same as JTC but with knurled round knob
with internal hex
Same as JTC but with knurled round knob
with screwdriver slot
Same as JTC but with hex knob
Same as JTC but with prybar knob
** Request availablity information.
*** Material: Nickel Plated Brass standard
Notes: 1. Contacts are ordered separately. See 100 Series contact section of Rack & Panel
2. When ordering hoods, hardware and connectors separately for use with JTD Monojacks,
connectors must be ordered as follows:
Pin connector = TMRAC34P8, TMRAC42P8, etc.
Socket connector = TMRAC34S8, TMRAC42S8, etc.
The number “8” indicates special housing for use with the JTD Monojack hardware
(available on sizes 34, 42, and 50).
DIMENSIONS
All dimensions for TMRAC housings are the
same as MRAC housings. All hoods, hardware,
and accesories used on the TMRAC Series are
the same as those used on the MRAC Series.
See MRAC Series section for part numbers and
dimensions. Note the TMRAC Series maximum
number of contacts is 50.
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXWPhone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 22
Rack & Panel
Heavy Duty, Industrial and Commercial, External Miniature
Rectangular Rack & Panel Connectors, Removable Contacts
TXAC SeriesTM
TXAC34SF2A010
TXAC34PM1A000
TXAC34PC1A700
The TXAC Series was designed for external
installation specifically for the industrial/
commercial customer in high temperature,
rough service applications. This series
features the same military-type anodized
aluminum hoods, rugged polyester thermo-
plastic insulators, screw-machine removable
contacts, guide and jack hardware, and
protective, anodized aluminum shells as the
XAC Series. These features make this Series
suitable for chassis mounting, bulkheads, or
any outside surface equipment.
Insulators:
Contact
Identification: Standard contact identification
is alphabetical.
Sizes:
.040" diameter and .062"
diameter contacts in 7.5-amp
and 13-amp current ratings.
Contact
Resistance:
@ 7.5 amps, 14 millivolts max.
@ 13 amps, 10 millivolts max.
Termination
Types:
Crimp, dip-solder, solder
removable in .040" and .062"
diameter. Wire Wrap tails and
stabilizing bushings for .025"
and .045" square.
Current Rating: 7.5 amps maximum for
.040" contacts.
13 amps maximum for
.062" contacts.
SPECIFICATIONS
Polyester thermoplastic,
green color. High potential
performance: withstanding
voltage is one minute
electrification at 2000 VAC
(sea level).
Insulation
Resistance:
500V
Thermal Shock: -55oF to +150oF
Hoods:
Anodized aluminum. May be
applied on plug or
receptable. Both top and side
opening hoods available.
Polarization: Gold Plated guides provide
positive polarization.
Polarized nickel-plated brass
and/or passivated stainless
steel with anodized aluminum
knobs are available.
7-position pin and slot
polarization on shells.
Number of
Contacts:
Eight size connectors: 9-, 14-,
18-, 20-, 26-, 34-, 42- and 50contact, available in either
.040" or .062" diameter.
Contacts:
Must be ordered separately.
Select from crimp, solder, dip
solder, shielded or WireWrap termination contacts.
See 100 Series contact
section.
®
CSA Certified File No.
LR34182
Recognized under the Component Program
of Underwriters Laboratories Inc. File No. E31650 ®
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 23
Rack & Panel
TXAC SeriesTM
Heavy Duty, Industrial and Commercial, External Miniture
Rectangular Rack & Panel Connectors, Removable Contacts
ORDERING INFORMATION
Omit steps not required
TXAC
■ Step 1
■ Step 2
Insert
Series
Code:
TXAC
No. of
Contacts:
9, 14, 18, 20,
26, 34, 42,
and 50
See note 1
below.
34
■ Step 5
■ Step 4
Pin or Socket Jackscrews Shell Type:
Contacts:
(See bottom ** 0 No shell
P - Pin
chart)
**
1 Plug shell,
S - Socket
style 1*000.
■ Step 3
**
S
D
■ Step 7
■ Step 6
Polarization (See
bottom
Position:
A, B, C, D, E, chart)
F or G.
Omit letter
when
polarization is
not required.
2 Receptacle
shell, style
2*000.
**
3 Plug shell,
monojack type,
style 3*000.
**
4 Receptacle,
monojack type,
style 4*000.
**
7 Stainless Steel
Plug shell, style
7*000.
**
8 Stainless Steel
Receptacle shell,
style 8*000.
**
Polarizing Position
Request availability
**
information
**
■ Step 4
Jackscrews and Jacksockets
*** M- Polarized short turnable jackscrew and
jacksocket. Cannot be used with hoods.
*** C- Polarized long turnable jackscrew and
jacksocket for use with hoods.
*** D- Polarized one-piece mono-jackscrew and
mono-jacksocket (no separate knob); to be
used with hoods on sizes: 34, 42, and 50.
*** FPolarized fixed jackscrew and jacksocket
usable with or without hood (no knob required).
Sizes: 34, 42, and 50.
** MW- Same as M but with knurled round knob with
internal hex.
** MU- Same as M but with knurled round knob with
screwdriver slot.
** MX- Same as M but with hex knob.
** CW- Same as C but with knurled round knob with
internal hex.
** CU- Same as C but with knurled round knob with
screwdriver slot.
** CX- Same as C but with hex knob.
** CZ- Same as C but with prybar knob.
*** Request
*** Material
4
A
3
00
■ Step 8
■ Step 9
Mounting Plate:
00- When no
mounting
plate is
required
*10- Mounting
plate, style
#0010.
*Mounting plates
are not used with
“M”, “C” or “D”
jackscrews.
Special Gaskets:
Omit letter when gaskets
are not required.
**
G- Bulkhead gasket, style
#0000G. Use only
when mounting plate is
specified.
**
F- Face gasket, style
#0000F. Use with male
insert only.
**
B- If both gasket #0000G
and gasket #0000F
are desired.
**
**
Check plant for availability
on all gaskets.
■ Step 7
Formed Hoods:
0- No Hood.
3- Hood, top opening, style #0300, for use with Type “C”
or “D” jackscrews.
4- Hood, side opening, style #0400, for use with Type “C”
or “D” jackscrews.
5- Hood, top opening, style #0500J, for use with “F”
style jackscrews.
6- Hood, side opening, style #0600J, for use with “F”
style jackscrews.
Deep Drawn Hoods:
7- Hood, top opening, style #0700, for use with Type “C”
or “D” jackscrews.
8- Hood, side opening, style #0800, for use with Type “C”
or “D” jackscrews.
9- Hood, top opening, style #0900, for use with
“F” jackscrews.
2- Hood, side opening, style #0200, for use with
“F” jackscrews.
Note: Addition of “X” to code # indicates cable opening
larger than std. See hoods for cable opening size.
Example: TXAC20PC1A300 X
availability information
Nickel plated brass - standard
Note: 1. Contacts are ordered separately. See 100 Series contact section of Rack & Panel
DIMENSIONS
All dimensions for TXAC housing are the same
as MRAC housings. All hoods, shells, hardware,
and accesories used on the TXAC Series are
the same as those used on the XAC Series.
See the XAC Series section for part numbers
and dimensions. Note the TXAC Series
maximum number of contacts is 50.
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 24
Rack & Panel
MRA Series
Miniature Rectangular / #16 Contacts / .062" Dia. / 13 Amps
Receptacle MRA 34S-G
Plug MRA 34P-G
Hood
The MRA Series offers compact, lightweight
and self-aligning plugs and receptacles with
unusually high current and voltage ratings for
their size. Performance tests show them to
well exceed military standards. Except for
contact size, the MRA and MRE Series share
the same hoods, hardware and accessories.
Right angle, dip solder, pin or socket contacts
are available. Consult factory.
Dimensions are for reference only and are
subject to change. Outline drawings on request.
Current Rating:13 amps
Number of
contacts:
9, 14, 20, 34, 41, 42, 50, 508, 66, 75, 104
Pin Contacts: .062 diameter, gold plated
brass
Socket
Contacts:
Phosphor bronze, gold plated
Terminations: .070 dia. solder cup is
standard. Will accommodate
up to #16 AWG stranded
wire. Pin and Socket
contacts available with .030
diameter dip solder terminations. Consult Sales Dept.
for lengths available.
Electrical Data:Meets high potential
performance of MIL-C-28748.
Military versions are QPL’d to
M28748/1 and M28748/2.
The minimum dielectric
withstanding voltage is one
minute electrification 1000
VAC, sea level.
Dielectric:
SPECIFICATIONS
Polarization:
Hoods:
Gray glass filled diallyl
phthalate, per MIL-M-14,
SDG-F.
Gold plated guides provide
polarization. Polarized nickelplated brass and/or passivated
stainless steel jackscrews with
anodized aluminum knobs
are available.
Anodized aluminum. May be
applied to either plug or
receptacle. Both top and side
opening hoods available.
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 25
Rack & Panel
Miniature Rectangular / #16 Contacts / .062" Dia. / 13 Amps
MRA Series
TERMINATION TYPES
Solder Cup
Dip Solder
For pin and socket contacts, .070 diameter
solder cup is the standard termination for
cable and panel mount applications. Wire
accommodation: up to #16 AWG stranded.
For pin and socket contacts, .030 diameter
dip solder terminations, straight or right angle
for mounting to printed circuit board or for use
with flexible cable.
GUIDE SOCKETS
3 Types of Guide Sockets are Available
Guide
Socket
Application
Actual
Size Photo
Code Letter
G*
The “G” type socket is the standard guide supplied. It
has good physical strength and may be used electrically
in a low current circuit or as a contact for ground leads.
G Type
For General Use
Phosphor
K*
N*
The “K” guide socket is an excellent electrical conductor.
Its extra spring-tension provides a high normal force
uniformily distributed along the surface of the engaged
pilot guide, thus minimizing electrical resistance.
The multivolt drop across extreme ends of the engaged
pilot and socket guide is 10 mv. at 20 amps.
K Type For High
Electrical Conductivity
Beryllium Copper
The high physical strength of the “N” guide socket allows
a greater degree of forcible tightening against a mounting
surface than is permitted by the other guide sockets.
This feature is particularly desirable for mounting
connectors which will be subject to severe vibration in
service. “N” guides are not to be used electrically.
N Type For extra
Mechanical Strength
Brass
Standard Guide
Pin mates with all types
Brass
* For passivated stainless steel add SS suffix
PHYSICAL DATA
WEIGHT
IN OZ.
PLUG
RECEPTACLE
NUMBER OF CONTACTS
9
.5
.4
14
.5
.4
20
.5
.4
34 41 42 50 50-8 66 75 104
1.1 1.2 1.2 1.5 1.5 2.0 2.3 3.1
.8 .9 .9 1.1 1.1 1.5 1.7 2.2
SPECIAL
MRA-50-8 with 8, 20 amp solder cup
contacts and 50, 13 amp solder cup
contacts
CONTACTS
CURRENT
RATING
PIN
MAX. WIRE
DIAMETER
SIZE
SOLDER
CUP DIA
8
20 amps
.093
#12 AWG
.106 D
.50
13 amps
.062
#16 AWG
.070 D
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXWPhone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 26
Rack & Panel
MRA Series
Miniature Rectangular / #16 Contacts / .062" Dia. / 13 Amps
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Drawings and corresponding part
numbers show G type guide sockets.
.86
.78
.37
.27
.37
.37
.27
.070 Dia.
Solder
Cup
1.313 1.000
.150 Typ.
.172 Typ.
4-40 UNC-2A THD.
Slot .038 Wide
Receptacle
MRA 9S-G
.44
.27
.44
.78
.86
.37
Plug
MRA 9P-G
.37
.27
.86
.37
.27
.78
.37
.27
.062 Dia.
.062 Dia.
.070 Dia.
Solder
Cup
.150 Typ.
.070 Dia.
Solder
Cup
1.250
Slot
.038 Wide
.937
1.563
1.250
Slot
.038 Wide
.150 Typ.
.075 Typ.
.075 Typ.
.168 Typ.
4-40 UNC-2
THD. Type
.130 Typ.
.175 Typ.
4-40 UNC-2 THD. Type
.130 Typ.
Receptacle
MRA 14S-G
Receptacle
MRA 20S-G
Plug
MRA 14P-G
.86
.44
.75
.47
.070 Dia.
Solder
Cup
.23
.86
.37
.27
.075
Typ.
.78
.37
Plug
MRA 20P-G
.27
.78
.37
.37
.27
.27
.075
Typ.
2.312
2.000
2.625
1.688
Slot
.038 Wide
.070 Dia.
Solder
Cup
Mounting Holes For No. 4
Machine Screws
4-40 UNC-2
THD. Type
Slot .038 Wide
.180 Typ.
.130 Typ.
Receptacle
MRA 34S-G
Plug
MRA 34P-G
4-40 UNC-2 THD. Type
Receptacle
MRA 41S-G
Plug
MRA 41P-G
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 27
Rack & Panel
Miniature Rectangular / #16 Contacts / .062" Dia. / 13 Amps
MRA Series
OUTLINE
Dimensions are for reference only and are subject
to change. Outline drawings on request.
Drawings and corresponding part numbers show
G type guide sockets.
.75
.47
.23
.075
Typ.
.86
.09R
.37 .27
.27 .37
.78
.09
.14
.37
.075
Typ.
.062 Dia.
2.313
.86
.27 .37
.88
.75
.47
.23
.78
.27
2.282
.070 Dia.
Solder
Cup
2.594
.070 Dia. 2.000
Solder
Cup
Mounting
Holes For
No. 4
Machine
Screws
2.719
.180 Typ.
4-40 UNC-2 THD.
Mounting Holes For
No. 4 Machine Screws
Receptacle
MRA 42S-G
.86
4-40 UNC-2 THD.
.37 .27
.075
Typ.
.25
Slot .038 Wide
Plug
MRA 50P-G
.86
.27 .37
.09
.14
1.234
1.109
.77
.23
.78
.27 .37
.180 Typ.
Receptacle
MRA 50S-G
Plug
MRA 42P-G
1.125
.50
.150
Typ.
Slot .038 Wide
.78
.37 .27
.106 Dia.
Solder
Cup
1.969
2.281
.16
Mounting Holes
For No. 4 Machine
Screws
4-40 UNC-2A THD.
.180 Typ.
Receptacle
MRA 50-8S-G
.150
Typ.
Slot .038 Wide
2.719
Mounting
Holes For
No. 4 Machine
Screws
.070 Dia.
Solder Cup
1.531
.78
.27 .37
.37 .27
4-40 UNC-2 THD.
.075
Typ.
Slot .038 Wide
Plug
MRA 75P-G
.78
8-32 UNC-2A Thd.
.560
.88
.86
.31R
.180 Typ.
Receptacle
MRA 75S-G
Plug
MRA 50-8P-G
1.125
.50
.25
2.282
2.594
.070 Dia.
Solder
Cup
.44
.560
.37
.37
.13
2.750
.038 Dia.
hole
for safety
wire
2.375
2.281
1.969
.16
Mounting Holes For
No. 4 Machine
Screws
.180 Typ.
4-40
UNC-2 THD.
Receptacle
MRA 66S-G
Slot .038 Wide
Plug
MRA 66P-G
.180 Typ.
4-40
UNC-2 THD.
Receptacle
MRA 104S-J
.27
.16
.16
.98
Plug
MRA 104P-JT
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXWPhone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 28
Rack & Panel
Miniature Rectangular / #16 Contacts / .062" Dia. / 13 Amps
MRA Series
JACKSCREWS & JACKSOCKETS
Polarized jackscrews give the ease and assurance of threaded positive coupling. The actuating
side consists of two turnable screws, one male
and one female, each with knurled and slotted
knobs. On the mating half are the two fixed
screws required to complete the locking action.
When mated, the jackscrews may be locked with
a safety wire through the hole in the self-locking
pin (in the jackscrew shaft).
.78
4-40 UNC 2 Thread
except size 104 which is
6-32 UNC 2
.98 for
size 104
Jacksocket
B
A
.16
MonoJackscrew
6-32 UNC 2 Thread
except size 104 which is
8-32 UNC2
Jackscrew
.16
Mating connector half with turnable
Jackscrews-with-Knobs.
Code designation: JT
MonoJacksocket .052 Dia. Safety Wire Hole
F
Hood Self Locking
Pin
E
D
C
Connector with fixed Jackscrews.
Code designation: J
The drawings show the extension of the jackscrew knobs beyond a typical MRA connector
and beyond the connector-and-hood assembly
(center drawings). Dimensions given are
constant for all connectors except as noted.
Other dimensions applicable to various hood
styles are detailed in the chart.
Mating connector half with Hood
and turnable Monojacks.
Code designation: JTDH, JTDH1
Mating connector half with Hood and
turnable Long Jackscrews-with
Knobs. Code designation: JTCH,
JTCH1
DIMENSIONS
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Connector Size
Dimension A
H H1 H8 H9
Dimension E
Dimension B Dimen Dimen
C
D
H H1 H8 H9
H H1 H8 H9
MRA 9
MRA 14
MRA 20
MRA 34
MRA 41
MRA 42
MRA 50
MRA 50-8
MRA 66
MRA 75
MRA 104
–
–
–
.63
.63
.58
.58
.77
.77
.56
.67
–
–
–
.63
–
.58
.58
.50
.50
.56
.50
.59
.59
.59
.63
.63
.58
.58
–
–
.56
–
.58
.58
.58
.63
–
.58
.58
–
–
.56
–
.59
.59
.59
.63
–
.58
.58
.70
.70
.56
.67
–
–
–
.63
–
.58
.58
–
–
.56
–
–
–
–
.63
–
.58
.58
–
–
.56
–
–
–
–
.63
–
.58
.58
.50
.50
.56
.50
.80
.80
.80
.80
.80
.80
.80
.80
.80
.80
.80
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.52
–
–
–
2.41
2.41
2.41
2.41
2.47
2.47
2.41
3.42
2.41
2.41
2.41
2.41
2.41
2.41
2.41
–
–
2.41
–
2.09
1.84
1.84
2.41
–
2.41
2.41
–
–
2.41
–
2.41
2.41
2.41
2.41
–
2.41
2.41
2.41
2.41
2.41
3.42
Dimension F
H H1 H8 H9
–
–
–
2.41
–
2.41
2.41
2.19
2.19
2.41
3.25
–
–
–
2.41
–
2.41
2.41
–
–
2.41
–
–
–
–
2.41
–
2.41
2.41
–
–
2.41
–
–
–
–
2.41
–
2.41
2.41
2.19
2.19
2.41
3.25
New Monojacks Assemble and Disassemble With Remarkable Ease and Speed
To free the connector from the hood, simply
remove four screws. Monojacks may be used
on miniature rectangular connectors with from
34 to 104 contacts, molds have 2 center thru
holes and 4 mounting holes.
MONOJACKS ARE CAPTIVATED IN KEYHOLE
SLOT OF HOOD AS SHOWN ABOVE.
WHEN USING SHELLS, MONOJACKS ARE
CAPTIVATED IN KEYHOLE OF SHELL AND
CLEARANCE HOLES ARE PLACED IN HOODS.
Winchester/Retconn
MOLDINGS HAVE STRAIGHT THRU HOLES
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 29
Rack & Panel
Miniature Rectangular / #16 Contacts / .062" Dia. / 13 Amps
MRA Series
OUTLINE
JACKSCREWS & JACKSOCKETS
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.19 Dia.
.22 Dia.
.50
.22 Dia.
.078 Int.
Hex.
.25 Hex
A
Typ.
A
Typ.
A
Typ.
JTCW
A
Typ.
JTCU
JTCX
.19 Dia.
JTCZ
.22 Dia.
.078 Int. Hex
1
.36
JTW
JTU
.25 Hex
6-32 UNC 2 THD.
(Typ)
.78
.80 Typ.
6-32 UNC 2 THD. (Typ)
.16 Typ.
JTX
JZ
DIMENSIONS
All jackscrews and sockets are stainless steel, passivated,
except J & JTD which are nickel-plated brass. All knobs
are aluminum, anodized except JTW and JTCW which are
stainless steel, passivated.
Hood Type
Type JTCW
Size
9
14
20
34
41
42
50
50-8
66
75
H
H1
H8
Dimension A
– 2.22 1.91
– 2.22 1.66
– 2.22 1.66
2.22 2.22 2.22
2.22 2.22
–
2.22 2.22 2.22
2.22 2.22 2.22
2.22 –
–
2.22 –
–
2.22 2.22 2.22
H9
Size
2.22
9
2.22 14
2.22 20
2.22 34
–
41
2.22 42
2.22 50
2.22 50-8
2.22 66
2.22 75
Type JTCU
H
H1
H8
Dimension A
– 2.47 2.16
– 2.47 1.91
– 2.47 1.91
2.47 2.47 2.47
2.47 2.47
–
2.47 2.47 2.47
2.47 2.47 2.47
2.47 –
–
2.47 –
–
2.47 2.47 2.47
H9
Size
2.47
9
2.47 14
2.47 20
2.47 34
–
41
2.47 42
2.47 50
2.47 50-8
2.47 66
2.47 75
Type JTCX
H
H1
H8
Dimension A
– 2.34 2.03
– 2.34 1.78
– 2.34 1.78
2.34 2.34 2.34
2.34 2.34
–
2.34 2.34 2.34
2.34 2.34 2.34
2.34 –
–
2.34 –
–
2.34 2.34 2.34
H9
Size
2.34
9
2.34 14
2.34 20
2.34 34
–
41
2.34 42
2.34 50
2.34 50-8
2.34 66
2.34 75
Type JTCZ
H
H8
H9
Dimension A
– 2.47 2.16
– 2.47 1.91
– 2.47 1.91
2.47 2.47 2.47
2.47 2.47
–
2.47 2.47 2.47
2.47 2.47 2.47
2.47 –
–
2.47 –
–
2.47 2.47 2.47
H1
2.47
2.47
2.47
2.47
–
2.47
2.47
2.47
2.47
2.47
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 30
Rack & Panel
Miniature Rectangular / #16 Contacts / .062" Dia. / 13 Amps
MRA Series
OUTLINE
HOODS - DRAWN ALUMINUM
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.08
.228 Dia. 2 Holes For
104*
.191 Dia. 2 Holes*
“Y”
Style
D
C
H
B
G
A
G
D
E
E
C
.08
DIMENSIONS
.08
A
Top Cable Opening
DIMENSIONS – TOP OPENING
Catalog
No.
“Z”
Style
B
A
B
MRA 34H-491 2.09
C
.84
D
1.17 1.59
E
F
G
.66 x .75
–
1.688
Wt.
Style
Fits
Oz. Connector
(cable
opening)
Side Cable Opening
DIMENSIONS – SIDE OPENING
Catalog
No.
A
B
C
D
.84
1.17
E
H
G
.6
MRA 34P
MRA 34S
“Y”
MRA 50-8H9
2.38 1.22 1.17
2.92
.84D
1.34
“Z”
MRA 34H9-491 2.09
1.59 .64 x .75 1.06
Wt.
Style
Fits
Oz. Connector
.6
MRA 34P
MRA 34S
“Z”
1.969
.8
MRA 50-8P
MRA 50-8S
“Y”
1.688
MRA 50-8H
2.38 1.22 1.17 1.69
1.03D
–
1.969
.8
MRA 50-8P
MRA 50-8S
MRA 66H
2.38 1.22 1.17 1.69
1.03
–
1.969
.8
MRA 66P
MRA 66S
“Y”
MRA 66H9
2.38 1.22 1.17
2.92
.84D
1.34
1.969
.8
MRA 66P
MRA 66S
“Y”
MRA 104H
2.84 1.63 2.23 2.75
1.19D
–
2.375 1.0
MRA 104P
MRA 104S
“Y”
MRA 104H9
2.84 1.63 2.23
3.39
1.19D
1.63
2.375
1.0
MRA 104P
MRA 104S
“Y”
OUTLINE
HOODS - FORMED ALUMINUM
MRE Series hoods for use with
MRA Series connectors
DIMENSIONS
Top Cable Opening
H and H-8 Cable Clamps (Top Opening)
Code No.
MRE 9H*
MRE 9H-8
MRE 14H*
MRE 14H-8
MRE 20H*
MRE 20H-8
MRE 34H
MRE 34H-8
MRE 41H
MRE 42H
MRE 42H-8
MRE 50H
MRE 50H-8
MRE 75H
MRE 75H-8
Dimensions
A
B
C
D
.28
.28
.28
.28
.25
.25
.28
.28
.28
.09
.09
.09
.09
.09
.09
1
1
.75
.75
.75
.75
1.25
1.25
1.25
1.30
1.30
1.30
1.30
1.31
1.31
1.31
1.30
1.19
1.05
1.19
1.05
1.67
1.75
1.67
1.72
1.80
1.72
1.80
1.73
1.86
1.31
1.31
1.25
1.25
1.56
1.56
2
2
2.63
2.31
2.31
2.59
2.59
2.59
2.59
Cable
Opening Wt.
E
F G Oz.
.44
.44
.5
.5
.5
.5
.83
.83
.5
.83
.83
.83
.83
1.19
1.19
.31D
.31
.44D
.38
.44D
.38
.66D
1.06
.66
.63D
1.06
.63D
1.06
.63
1
–
.59
–
.59
–
.66
–
.56
.44
–
.56
–
.56
.88
.88D
.3
.3
.3
.3
.3
.3
.6
.6
.6
.7
.7
.8
.8
1.0
1.0
Side Cable Opening
H-1 and H-9 Cable Clamps (Side Opening)
Fits
Connector
Code No.
MRA 9 (P or S)
MRA 9 (P or S)
MRA 14 (P or S)
MRA 14 (P or S)
MRA 20 (P or S)
MRA 20 (P or S)
MRA 34 (P or S)
MRA 34 (P or S)
MRA 41 (P or S)
MRA 42 (P or S)
MRA 42 (P or S)
MRA 50 (P or S)
MRA 50 (P or S)
MRA 75 (P or S)
MRA 75 (P or S)
MRE 9H-1
MRE 9H-9
MRE 14H-1
MRE 14H-9
MRE 20H-1
MRE 20H-9
MRE 34H-1
MRE 34H-9
MRE 41H-1
MRE 42H-1
MRE 42H-9
MRE 50H-1
MRE 50H-9
MRE 75H-1
MRE 75H-9
Dimensions
A
B
C
D
.28
.28
.28
.28
.28
.28
.28
.28
.28
.09
.09
.09
.09
.09
.09
1.28
1.28
1.28
1.28
1.28
1.28
1.25
1.25
1.25
1.30
1.30
1.30
1.30
1.31
1.31
1.63
1.61
1.69
1.55
2
1.86
2.42
–
3.06
2.73
–
3.02
–
3.02
–
1.31
1.31
1.25
1.25
1.56
1.56
2
2
2.63
2.31
2.31
2.59
2.59
2.59
2.59
Cable
Opening Wt.
E
F G Oz.
.44
.44
.5
.5
.5
.5
.83
.83
.5
.83
.83
.83
.83
1.19
1.19
.31D
.59
.38D
.59
.38D
.66
.66D
.81
.66
.63
.84
.63
1.06
.63
1
–
.3
.31 .3
–
.3
.38 .3
–
.3
.38 .3
–
.6
.56 .6
.44 .6
.5 .7
.56 .7
.5 .8
.56 .8
.88 1.0
.88 1.0
Fits
Connector
MRA 9 (P or S)
MRA 9 (P or S)
MRA 14 (P or S)
MRA 14 (P or S)
MRA 20 (P or S)
MRA 20 (P or S)
MRA 34 (P or S)
MRA 34 (P or S)
MRA 41 (P or S)
MRA 42 (P or S)
MRA 42 (P or S)
MRA 50 (P or S)
MRA 50 (P or S)
MRA 75 (P or S)
MRA 75 (P or S)
* H Hoods for MRA 9, 14, and 20 will not accept JTC
hardware. Use H8 hoods.
Winchester Electronics
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 31
Rack & Panel
Miniature Rectangular / #16 Contacts / .062" Dia. / 13 Amps
MRA Series
Lock Tabs (MRE-V shown)
HOODS - LOCKING
Lever & Pivot Assemblies (MRE-VL shown)
Vibration Locks*
Vibration locks offer simplicity of design and
positive locking in excess of 50G shock impact
and 10G vibration acceleration. Mating halves
automatically lock when engaged. To unlock,
MRA 9, 14, 20, depress the levers. Drilled holes in the levers
are provided for safety wiring. Vibration
locks are available separately for assembly
on connectors now in service. Each code
number indicates two units: two levers with
two pivots, and two lock tabs.
34, 41, 42, 66
*US Patent Number 2760174
Lever
Used on
Lock Tabs
& Pilot (See Note) Connectors
Assembly
MRE-VL
MRE-VL2
MRE-V
MRE-V2
MRA 50,75
Note: When panel mounting the lock-tab half of a MRA 34, MRA 42 or MRA 50 and MRA 66 connector, flat washers
(.033 minimum thickness) should be used on the mounting screws to shim the moulding away from the panel.
DIMENSIONS / OUTLINE
MOUNTING BRACKETS
Code No.
A
B
C
DIMENSIONS
D E F G
Wt.
Oz.
H
.128 Dia 3 Holes
MRE 50B 1.06 .688 3.031 3.44 .13 .28 .72 (No. 4 Mounting
Screw)
.4
.150 Dia 3 Holes
MRE 75B 1.48 1.047 3.062 3.56 .14 .30 1.14 (No. 6 Mounting
Screw)
.6
MRA 9 FM
MRA 14 FM
MRA 20 FM
MRA 26 FM
MRA 34 FM
MRA 41 FM
MRA 42 FM
MRA 50 FM
MRA 75 FM
3
2
2
2
1
2
1
1
1
G
C
2.625
D
Panel
Opening
MRA 50 and MRA 75 connectors
use the standard MRE 50 and MRE
75 mounting brackets
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Fig.
F
E
.11R
DIMENSIONS / OUTLINE
PRE-SHAPED NYLON
POTTING FORMS
Potting Form
Code No.
H
A
B
connector after potting. Because of floating
contacts, connector halves should always
be engaged during the potting operation to
preserve contact alignment.
Each form matches the back opening contour of
its appropriate shell, and stays easily in place
during the potting operation. Of negligible
weight, it need not be removed from the
Dimensions
A
B
.77
.93
1.12
1.18
1.38
2.18
1.69
1.97
1.98
.43
.49
.49
.61
.80
.49
.80
.80
1.16
A
B
B
B
.50 .63
Winchester/Retconn
A
A
Figure 1
.50 .63
.50 .63
Figure 2
Figure 3
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 32
Rack & Panel
Miniature Rectangular / #16 Contacts / .0262" Dia. / 13 Amps
MRA Series
ORDERING INFORMATION
Omit steps not required
MRA
■ Step 1
Insert Series
Code
By adding “ML”
to the series
code, connector
is supplied with
diallyl phthalate
type SDG-F
and mil plated
contacts.
Example:
MRAML
■ Step 2
Number of
Contacts:
9, 14, 20, 34,
41, 42, 50,
50-8, 66, 75,
104
■ Step 3
Contact
Designation:
P - Pin
S - Socket
When
ordering
molding less
hardware to
be used with
mono-jacks,
see Note
below.
34
■ Step 4
Type of
Contact:
Blank =
Standard
Solder Cup
Straight
Dip Solder
.030" dia.:
D3 = .094"
D4 = .125"
D5 = .156"
For additional
lengths in 1/32"
increments,
contact
Winchester’s
Sales
Department.
G
S
■ Step 5
Guides and
Jackscrew
Locks:
(See bottom
Chart)
H
VL
■ Step 6
■ Step 7
■ Step 8
Hoods:
Vibration
Accessories:
H - Standard Locks:
FM - Potting
Top
V - Lock Tab
Forms.
Opening* V2 - Lock Tab
Cannot be
Used with
H1 - Standard
(Size 50
Hoods.
Side
& 75)
Opening
Request
VL - Lever &
availability
H8 - Large Top
Pivot Ass’y
informaOpening
VL2 - Lever &
tion.
H9 - Large Side
Pivot Ass’y
Opening
(Size 50
& 75)
See Hood
Section for
Availability
*(Note: H Hoods
for MRA 9, 14
and 20 will not
accept JTC
hardware. Use
H8 hoods.)
■ Step 9
Special
Options:
Consult Sales
Department
■ Step 5
Guides
*G
Phosphor Bronze Cylindrical Guides*
*K
Beryllium Copper Cylindrical Guides
*N
Brass Cylindrical Guides*
Guides are not recommended for Size 104
“P” indicates two guide pins or two jackscrews
(EX. JTCP)
“S” indicates two guide sockets or two jacksockets.
(Ex. GS)
Jackscrew Locks
*** J
Polarized Fixed Jackscrew and Jacksocket
JT
Polarized Short Turning Jackscrew
and Jacksocket
JTC
Polarized Long Turning Jackscrew
and Jacksocket
*** JTD
Polarized Long Turning Mono-Jackscrew and
Mono-Jacksocket for Sizes 34, 42, 50, 66,
75, and 104 only.
** JZ
** JTW
** JTU
** JTX
** JTCW
** JTCU
** JTCX
** JTCZ
Same as J but with 6-32 mtg. thd.
(Std. on 104)
Same as JT but with knurled round knob
with internal hex (not avail. 104)
Same as JT but with knurled round knob
with screwdriver slot (not avail. 104)
Same as JT but with hex knob
(not avail. 104)
Same as JTC but with knurled round knob
with internal hex (not avail. 104)
Same as JTC but with knurled round knob
with screwdriver slot (not avail. 104)
Same as JTC but with hex knob
(not avail. 104)
Same as JTC but with prybar knob
(not avail. 104)
** Request availablity information.
*** Material: Nickel-plated brass - standard.
* For passivated stainless steel add SS suffix. (Example: MRA34SGSS)
Mounting Note: Connectors MRA 9, MRA 14, MRA 20 and MRA41 use guides or fixed jacks for mounting in a
hood or on a panel. Connectors MRA 34, MRA 42, MRA 50, MRA 66, MRA 75 use four #4 machine screws,
and MRA 104 uses four #6 machine screws for mounting in a hood or on a panel. Guides are not recommended for use with MRA 104.
Note:
When ordering hoods, hardware and connectors separately for use with JTD Monojacks, connectors must be ordered as follows:
Pin connector = MRA34P8, MRA42P8, etc.
Socket connector = MRA34S8, MRA42S8, etc.
The number “8” indicates special housing for use with the JTD Monojack hardware
(available on sizes 34, 42, 50, 66, 75 and 104).
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 33
Rack & Panel
MRE Series
Miniature Rectangular / #20 Contacts / .040" Dia. / 7.5 Amps
Receptacle MRE 14S-G
Plug MRE 14P-G
MRE Series plugs and receptacles are the
accepted standard for rectangular-shaped,
miniature, internal-type connectors. They
embody all of the features expected of true
miniaturization: maximum utility of space,
extremely lightweight and unusually high
Hood MRE 14H
working voltage and current ratings. Their
long life and trouble-free service continue to
make them highly popular for use in aircraft,
instrumentation and portable equipment.
The MRE and MRA series share the same
hoods, hardware and accessories.
SPECIFICATIONS
Current Rating:7.5 amps
No. of
Contacts:
7, 8, 9, 11, 14, 18, 20, 21,
26, 34, 41, 42, 50, 75, 104
Pin Contacts: .040 dia., gold plated brass
Socket
Contacts:
Phosphor bronze plated gold.
Termination
Types:
.048 dia. solder cup is
standard. It will accept up to
#20 AWG stranded wire. Pin
and Socket Contacts
available with dip solder
terminations, .025 Dia.
Check Sales Dept. for
lengths available.
Electrical Data:Meets high potential
performance requirements of
MIL-C-28748. Military
versions are QPL’d to
M28748/5 and M28748/6.
The dielectric withstanding
voltage is one minute at 1200
Dielectric:
Polarization:
Hoods:
volts.
Brown mineral filled diallyl
phthalate. Also available in
gray glass filled diallyl
phthalate, per MIL-M-14,
SDG-F.
Gold plated guides provide
positive polarization. Polarized
nickel-plated brass and/or
passivated stainless steel
jackscrews with anodized
aluminum knobs are
available.
Anodized aluminum. May be
applied to either plug or
receptacle. Both top and
side openings are available.
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXWPhone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 34
Rack & Panel
Miniature Rectangular / #20 Contacts / .040" Dia. / 7.5 Amps
MRE Series
TERMINATION TYPES
Solder Cup
Dip Solder
.048 diameter solder cup is the standard
termination for cable and panel mounting
applications. It will accept up to #20 AWG
stranded wire.
For mounting on printed circuit boards, .025
diameter straight dip solder terminations (for
Pin Contacts and Socket Contacts) are
available. Consult the Sales Department for
available lengths.
GUIDE SOCKETS
3 Types of Guide Sockets are Available
Guide
Socket
Application
Actual
Size Photo
Code Letter
G*
The “G” type socket is the standard guide supplied. It
has good physical strength and may be used electrically
in a low current circuit or as a contact for ground leads.
G Type
For General Use
Phosphor
K*
N*
The “K” guide socket is an excellent electrical conductor.
Its extra spring-tension provides a high normal force
uniformily distributed along the surface of the engaged
pilot guide, thus minimizing electrical resistance.
The multivolt drop across extreme ends of the engaged
pilot and socket guide is 10 mv. at 20 amps.
K Type For High
Electrical Conductivity
Beryllium Copper
The high physical strength of the “N” guide socket allows
a greater degree of forcible tightening against a mounting
surface than is permitted by the other guide sockets. This
feature is particularly desirable for mounting connectors
which will be subject to severe vibration in service. “N”
guides are not to be used electrically.
N Type For extra
Mechanical Strength
Brass
Standard Guide
Pin mates with all types
Brass
* For passivated stainless steel add SS suffix
PHYSICAL DATA
HOW TO ORDER: To obtain “K” or “N”
guides in place of the standard “G” type,
substitute the desired socket style code
letter (“K” or “N”) for “G” in both the Plug
and Receptacle Code Numbers.
(See Code Numbers in table at right.
Plug
Total
No. of
Winchester
Contacts Electronics
Code No.
7
8
9
11
14
18
20
21
MRE 7P-G
MRE 8P-N
MRE 9P-G
MRE 11 P-G
MRE14P-G
MRE 18P-G
MRE 20P-G
MRE 21P-G
Recept.
Winchester
Electronics
Code No.
MRE
MRE
MRE
MRE
MRE
MRE
MRE
MRE
7S-G
8S-N
9S-G
11S-G
14S-G
18S-G
20S-G
21S-G
No.
Standard
Contacts,
7.5 Amps
(.048 dia.
solder cup
for #20
AWG)
No.
Standard
Contacts,
10 Amps
(.052 dia.
solder cup
for #18
AWG)
7
8
9
11
14
18
20
21
none
none
none
none
none
none
none
none
Weight
Oz.
Plug Rec.
.3
.2
.3
.3
.3
.4
.5
.5
.3
.2
.3
.3
.3
.4
.4
.5
Plug
Total
No. of
Winchester
Contacts Electronics
Code No.
26
34
41
42
50
75
104
MRE
MRE
MRE
MRE
MRE
MRE
MRE
26P-G
34P-G
41P-G
42P-G
50P-G
75 P-G
104P-JT
Recept.
Winchester
Electronics
Code No.
MRE
MRE
MRE
MRE
MRE
MRE
MRE
26S-G
34S-G
41S-G
42S-G
50S-G
75S-G
104S-G
No.
Standard
Contacts,
7.5 Amps
(.048 dia.
solder cup
for #20
AWG)
26
34
41
42
50
75
104
No.
Standard
Contacts,
10 Amps
(.052 dia.
solder cup
for #18
AWG)
none
none
none
none
none
none
none
Weight
Oz.
Plug Rec.
.6
.8
.8
.9
1.0
1.5
3.3
.5
.7
.6
.8
.9
1.3
2.2
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 35
Rack & Panel
MRE Series
Miniature Rectangular / #20 Contacts / .040" Dia. / 7.5 Amps
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.86
.09 R
.37
.27
.78
.37
.27
.37
.075
Typ.
.906
1.219
.13
.172
Typ.
4-40 NC-2 THD.
Receptacle
MRE 7S-G
Slot .038 Wide
Plug
MRE 7P-G
.72
.75
.09 R
.37
.20
.37
.20
.37
.070
Typ.
.750
.562
.09 R
.094
Typ.
4-40 NC-2 THD.
Slot .020 Wide
Note: For MRE8, "G" guides not available
Receptacle
MRE 8S-N
Plug
MRE 8P-N
.86
.37
.27
.78
.37
.37
.27
.075
Typ.
1.313
1.000
.11
.172
Typ.
.09 R
Slot .038 Wide
4-40 NC-2 THD.
Receptacle
MRE 9S-G
Plug
MRE 9P-G
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXWPhone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 36
Rack & Panel
Miniature Rectangular / #20 Contacts / .040" Dia. / 7.5 Amps
MRE Series
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.86
.44
.27
.78
.37
.37
.86
.27
.075
Typ.
.56
.09R
.27
.78
.37
.37
.27
.075
Typ.
1.250
1.313
.937
1.000
.06
.09R
.130 Typ.
.13R
Receptacle
MRE 14S-G
4-40 NC-2
THD.
SLOT 0.38 WIDE
.130 Typ.
4-40 NC-2 THD.
.13R
Plug
MRE 14P-G
Receptacle
MRE 18S-N
.37
.86
.44
.09R
.27
.37
Plug
MRE 18P-N
.86
.37
.78
.37
.27
.075
Typ.
.78
.37
.27
SLOT .038 WIDE
.27
.075
Typ.
2.250
1.560
1.937
1.250
.06
.13
.09R
.130 Typ.
4-40 NC-2
THD.
Receptacle
MRE 20S-N
SLOT 0.38 WIDE
.172
SLOT .038 WIDE
4-40 NC-2 THD.
.13R
Plug
MRE 20P-N
Receptacle
MRE 21S-N
Plug
MRE 21P-N
.75
.86
.47
.86
.56
.09R
.27
.78
.37
.37
.075
Typ.
.27
.09R
.23
.27
.78
.37
.37
.27
.075
Typ.
.13
2.000
1.625
1.688
1.312
.06
.13R
.130 Typ.
4-40 NC-2
THD.
Receptacle
MRE 26S-N
SLOT 0.38 WIDE
Plug
MRE 26P-N
MOUNTING
HOLES
FOR NO.4
MACHINE
SCREWS
.180 Typ.
Receptacle
MRE 34S-N
4-40 NC-2 THD.
SLOT .038 WIDE
Plug
MRE 34P-N
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 37
Rack & Panel
Miniature Rectangular / #20 Contacts / .040" Dia. / 7.5 Amps
MRE Series
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.44
.075
Typ.
.27
.09R
.75
.47
.23
.78
.37 .27
.86
.37
.09R
.78
.37 .27
.86
.37
.27
.075
Typ.
.06
.16
2.625
2.313
2.312
2.000
.13R
MOUNTING
HOLES FOR
NO.4 MACHINE
SCREWS
SLOT 0.38 WIDE
4-40 NC-2
THD.
Plug
MRE 41P-N
.130 Typ.
Receptacle
MRE 41S-N
.180 Typ.
.075
Typ.
1.109
.77
.23
.78
.37 .27
.094 .13
Plug
MRE 42P-G
.86
.27 .37
.75
.47
.23
.86
.27 .37
SLOT 0.38 WIDE
Receptacle
MRE 42S-G
.88
1.234
4-40 NC-2
THD.
.09
.16R
.13
.78
.37 .27
.075
Typ.
.16
2.594
2.594
2.282 2.719
2.281 2.719
.16R
.16R
.180 Typ.
MOUNTING HOLES FOR
NO.4 MACHINE SCREWS
SLOT 0.38 WIDE
4-40 NC-2
THD.
Receptacle
MRE 75S-N
MOUNTING
HOLES
FOR NO.4
MACHINE SCREWS
4-40 NC-2
THD.
.180 Typ.
Receptacle
MRE 50S-N
Plug
MRE 75P-N
SLOT 0.38 WIDE
Plug
MRE 50P-N
1.531
.37
.44
.16
.37
.27
.37
.37
6-32 UNC
2A THD
.075
Typ.
2.375
.27
.44
.075
Typ.
8-32
UNC
2A THD
.78
.86
.78
1.359
.88
.781 1.094
2.750
.13R
MOUNTING
HOLES
FOR NO.4
MACHINE
SCREWS
.180 Typ.
.09R
.130 Typ.
062 DIA HOLE
FOR SAFETY WIRE
Receptacle
MRE 104S-JT
Plug
MRE 104P-J
4-40 NC-2
THD.
Receptacle
MRE 11S-G
SLOT 0.38 WIDE
Plug
MRE 11P-G
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXWPhone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 38
.27
Rack & Panel
MRE Series
Miniature Rectangular / #20 Contacts / .040" Dia. / 7.5 Amps
JACKSCREWS & JACKSOCKETS
Polarized jackscrews give the ease and
assurance of threaded positive coupling. The
actuating side consists of two turnable screws,
one male and one female, each with knurled and
slotted knobs. On the mating half are the two
fixed screws required to complete the locking
action. When mated, the jackscrews may be
locked with a safety wire through the hole in the
self-locking pin (in the jackscrew shaft).
4-40 NC-2 THD.
EXCEPT SIZE 104
WHICH IS 6-32 NC 2
.78
.98 For
Size 104
The drawings show the extension of the jackscrew
knobs beyond a typical MRA connector and
beyond the connector-and-hood assembly (center
drawings). Dimensions given are constant for all
connectors except as noted. Other dimensions
applicable to various hood styles are detailed in
the chart.
.16
A
MONO
JACKSCREW
B
6-32 UNC 2 THREAD
EXCEPT SIZE 104
WHICH IS 8-32 UNC 2
JACKSOCKET
AND
OR
OR
JACKSCREW
.16
C
HOOD
Connector with fixed
Jackscrews.
Code designation: J
SELF LOCKING PIN
MONO
JACKSOCKET
052 DIA SAFETY WIRE HOLE
E
E
D
Mating connector half
with turnable Jackscrews-with-Knobs.
Code designation: JT
Mating connector half with Hood
and turnable Long Jackscrewswith Knobs. Code designation:
JTCH, JTCH1
Mating connector half
with Hood and
turnable Monojacks.
Code designation:
JTDH, JTDH1
DIMENSIONS
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Connec- Dimension A
tor Size H H1 H8 H9
Dimension E
Dimension B Dimen Dimen
C
H H1 H8 H9
D
H H1 H8 H9
MRE 7
MRE 8
MRE 9
MRE 14
MRE 18
MRE 20
MRE 21
MRE 26
MRE 34
MRE 41
MRE 42
MRE 50
MRE 75
MRE 104
–
–
–
–
–
–
–
–
.63
–
.58
.58
.56
.5
–
–
–
–
–
–
.67
.81
.63
.63
.58
.58
.56
.67
.58
.5
.59
.59
.59
.59
.59
.59
.63
.63
.58
.58
.56
–
.58
.5
.58
.58
.83
.58
.67
.59
.63
–
.58
.58
.56
–
–
.5
.59
.59
.59
.59
.59
.59
.63
–
.58
.58
.56
.67
–
–
–
–
–
–
–
–
.63
–
.58
.58
.56
–
–
–
–
–
–
–
–
–
.63
–
.58
.58
.56
–
–
–
–
–
–
–
–
–
.63
–
.58
.58
.56
.5
.80
.80
.80
.80
.80
.80
.80
.80
.80
.80
.80
.80
.80
.80
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.52
–
–
–
–
–
–
2.09
2.61
2.41
2.41
2.41
2.41
2.41
3.42
2.09
2.02
2.41
2.41
2.41
2.41
2.41
2.41
2.41
2.41
2.41
2.41
2.41
–
2.09
2.02
2.09
1.84
2.09
1.84
2.09
2.41
2.41
–
2.41
2.41
2.41
–
–
2.02
2.41
2.41
2.41
2.41
2.41
2.41
2.41
–
2.41
2.41
2.41
3.42
Dimension F
H H1 H8 H9
–
–
–
–
–
–
–
–
2.41
–
2.41
2.41
2.41
3.25
–
–
–
–
–
–
–
–
2.41
–
2.41
2.41
2.41
–
–
–
–
–
–
–
–
–
2.41
–
2.41
2.41
2.41
–
–
–
–
–
–
–
–
–
2.41
–
2.41
2.41
2.41
3.25
New Monojacks Assemble and Disassemble With Remarkable Ease and Speed
To free the connector from the hood simply
remove four screws. Monojacks may be used
on miniature rectangular connectors with from
MOLDINGS HAVE STRAIGHT THRU HOLES
34 to 104 contacts. Molds have 2 center thru
holes and 4 mounting holes.
MONOJACKS ARE CAPTIVATED IN KEYHOLE
SLOT OF HOOD AS SHOWN ABOVE.
WHEN USING SHELLS, MONOJACKS ARE
CAPTIVATED IN KEYHOLE OF SHELL AND
CLEARANCE HOLES ARE PLACED IN HOODS.
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 39
Rack & Panel
Miniature Rectangular / #20 Contacts / .040" Dia. / 7.5 Amps
MRE Series
OUTLINE
JACKSCREWS & JACKSOCKETS
.22
.50
.19 DIA
.22 DIA.
DIA.
.078 INT. HEX.
.25 HEX.
A
A
A
A
JTCW
JTCU
JTCX
JTCZ
.22 DIA.
.22
DIA.
.078 INT. HEX.
1"
.36
Dimensions are for reference
only and are subject to change.
Outline drawings on request.
JTW
JTU
.25 HEX.
6-32 UNC 2 THD.
(TYP.)
.78
.80 TYP.
6-32 UNC 2 THD. (TYP.)
.16 TYP.
JZ
JTX
DIMENSIONS
All jackscrews and sockets are stainless steel, passivated,
except for J & JTD which are nickel-plated brass. All knobs
are aluminum, anodized except JTW and JTCW which are
stainless steel, passivated.
Hood Type
Size
7
9
14
18
20
21
26
34
41
42
50
75
Type JTCW
H
H1
H8
Dimension A
– 1.91 1.91
– 2.22 1.91
– 2.22 1.66
– 2.22 1.66
– 2.22 1.66
1.91 2.22 1.91
2.22 2.22 2.22
2.22 2.22 2.22
2.22 2.22
–
2.22 2.22 2.22
2.22 2.22 2.22
2.22 2.22 2.22
H9
–
2.22
2.22
2.22
2.22
2.22
2.22
2.22
–
2.22
2.22
2.22
Type JTCU
Size
7
9
14
18
20
21
26
34
41
42
50
75
H
H1
H8
Dimension A
– 2.16 2.16
– 2.47 2.16
– 2.47 1.91
– 2.47 1.91
– 2.47 1.91
2.16 2.47 2.16
2.47 2.47 2.47
2.47 2.47 2.47
2.47 2.47
–
2.47 2.47 2.47
2.47 2.47 2.47
2.47 2.47 2.47
H9
–
2.47
2.47
2.47
2.47
2.47
2.47
2.47
–
2.47
2.47
2.47
Size
7
9
14
18
20
21
26
34
41
42
50
75
Type JTCX
H
H1
H8
Dimension A
– 2.03 2.03
– 2.34 2.03
– 2.34 1.78
– 2.34 2.03
– 2.34 1.78
2.03 2.34 2.03
2.61 2.34 2.34
2.34 2.34 2.34
2.34 2.34
–
2.34 2.34 2.34
2.34 2.34 2.34
2.34 2.34 2.34
H9
–
2.34
2.34
2.34
2.34
2.34
2.34
2.34
–
2.34
2.34
2.34
Size
7
9
14
18
20
21
26
34
41
42
50
75
Type JTCZ
H
H8
H9
Dimension A
– 2.16 2.16
– 2.47 2.16
– 2.47 1.91
– 2.47 2.16
– 2.47 1.91
2.16 2.47 2.16
2.77 2.47 2.47
2.47 2.47 2.47
2.47 2.47
–
2.47 2.47 2.47
2.47 2.47 2.47
2.47 2.47 2.47
H1
–
2.47
2.47
2.47
2.47
2.47
2.47
2.47
–
2.47
2.47
2.47
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 40
Rack & Panel
Miniature Rectangular / #20 Contacts / .040" Dia. / 7.5 Amps
MRE Series
OUTLINE
HOODS - FORMED ALUMINUM
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
DIMENSIONS
Top Cable Opening
Code No.
Dimensions
A
MRE 7H*
MRE 7H-8
MRE 8H*
MRE 8H-8
MRE 9H*
MRE 9H-8
MRE 14H*
MRE 14H-8
MRE 18H*
MRE 18H-8
MRE 20H*
MRE 20H-8
MRE 21H
MRE 21H-8
MRE 26H
MRE 26H-8
MRE 34H
MRE 34H-8
MRE 41H
MRE 42H
MRE 42H-8
MRE 50H
MRE 50H-8
MRE 75H
MRE 75H-8
MRA104H
Side Cable Opening
B
C
D
Cable
Opening Wt.
E
F G Oz.
.28
1 1.31 1.22 .44 .31D –
.3
.28
1 1.30 1.22 .44 .59 .31 .3
.28
1 1.31 .81 .44 .25D –
.2
.28
1 1.30 .81 .44 .31D –
.2
.28
1 1.31 1.31 .44 .31D –
.3
.28
1 1.30 1.31 .44 .59 .31 .3
.28 .75 1.19 1.25 .5 .44D –
.3
.28 .75 1.05 1.25 .5 .59 .38 .3
.28 .75 1.19 1.31 .63 .44D –
.4
.28 .75 1.25 1.31 .63 .63 .44 .4
.25 .75 1.19 1.56 .5 .44D –
.3
.25 .75 1.05 1.56 .5 .66 .38 .3
.28 .91 1.34 2.25 .44 .59 .31 .5
.28 .91 1.36 2.25 .44 .78 .31 .5
.28 1.28 1.72 1.63 .64 .59 .38 .4
.28 1.28 1.78 1.63 .64 .78 .44 .4
.28 1.25 1.69 2
.83 .66D –
.6
.28 1.25 1.75 2
.83 1.06 .56 .6
.28 1.25 1.69 2.63 .5 .66 .44 .6
.09 1.30 1.73 2.31 .83 .63D –
.7
.09 1.30 1.80 2.31 .83 1.06 .56 .7
.09 1.30 1.73 2.59 .83 .63D –
.8
.09 1.30 1.80 2.59 .83 1.06 .56 1.8
.09 1.31 1.75 2.59 1.19 .63 .88 1.0
.09 1.31 1.86 2.59 1.19 1
.88 1.0
FOR DIMENSIONS SEE PAGE RP/ 36
Fits
Connector
Code No.
MRE 7 (P or S)
MRE 7 (P or S)
MRE 8 (P or S)
MRE 8 (P or S)
MRE 9 (P or S)
MRE 9 (P or S)
MRE 14 (P or S)
MRE 14 (P or S)
MRE 18 (P or S)
MRE 18 (P or S)
MRE 20 (P or S)
MRE 20 (P or S)
MRE 21 (P or S)
MRE 21 (P or S)
MRE 26 (P or S)
MRE 26 (P or S)
MRE 34 (P or S)
MRE 34 (P or S)
MRE 41 (P or S)
MRE 42 (P or S)
MRE 42 (P or S)
MRE 50 (P or S)
MRE 50 (P or S)
MRE 75 (P or S)
MRE 75 (P or S)
MRE 7H-1
MRE 8H-1
MRE 8H-9
MRE 9H-1
MRE 9H-9
MRE 14H-1
MRE 14H-9
MRE 18H-1
MRE 18H-9
MRE 20H-1
MRE 20H-9
MRE 21H-1
MRE 21H-9
MRE 26H-1
MRE 26H-9
MRE 34H-1
MRE 34H-9
MRE 41H-1
MRE 42H-1
MRE 42H-9
MRE 50H-1
MRE 50H-9
MRE 75H-1
MRE 75H-9
MRA104H-9
Dimensions
A
B
C
D
Cable
Opening Wt.
E
F G Oz.
.28 1.28 1.53 1.22 .44 .31D –
.3
.28 1.28 1.13 .81 .44 .25
–
.2
.28 1.28 1.13 .81 .44 .59 .31 .2
.28 1.28 1.63 1.31 .44 .31D –
.3
.28 1.28 1.61 1.31 .44 .59 .31 .3
.28 1.28 1.69 1.25 .5 .38D –
.3
.28 1.28 1.55 1.25 .5 .59 .38 .3
.28 1.28 1.75 1.31 .63 .44D –
.3
.28 1.28 1.81 1.31 .63 .69 .44 .3
.28 1.28 2 1.56 .5 .38D –
.3
.28 1.28 1.86 1.56 .5 .66 .38 .3
.28 1.28 2.69 2.25 .44 .53 .25 .5
.28 1.28 2.72 2.25 .44 .78 .31 .5
.28 1.28 2.06 1.63 .64 .59 .38 .4
.28 1.28 2.13 1.63 .64 .78 .44 .4
.28 1.25 2.42 2
.83 .66D –
.6
.28 1.25 –
2
.83 .81 .56 .6
.28 1.25 3.06 2.63 .5 .66 .44 .6
.09 1.30 2.73 2.31 .83 .63 .5
.7
.09 1.30 – 2.31 .83 .84 .56 .7
.09 1.30 3.02 2.59 .83 .63 .5
.8
.09 1.30 – 2.59 .83 1.06 .56 .8
.09 1.31 3.02 2.59 1.19 .63 .88 1.0
.09 1.31 – 2.59 1.19 1
.88 1.0
FOR DIMENSIONS SEE PAGE RP/36
Fits
Connector
MRE 7 (P or S)
MRE 8 (P or S)
MRE 8 (P or S)
MRE 9 (P or S)
MRE 9 (P or S)
MRE 14 (P or S)
MRE 14 (P or S)
MRE 18 (P or S)
MRE 18 (P or S)
MRE 20 (P or S)
MRE 20 (P or S)
MRE 21 (P or S)
MRE 21 (P or S)
MRE 26 (P or S)
MRE 26 (P or S)
MRE 34 (P or S)
MRE 34 (P or S)
MRE 41 (P or S)
MRE 42 (P or S)
MRE 42 (P or S)
MRE 50 (P or S)
MRE 50 (P or S)
MRE 75 (P or S)
MRE 75 (P or S)
* H Hoods for MRE 7, 8, 9, 14, 18 and 20 will not accept JTC
hardware. Use H8 hoods.
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 41
Rack & Panel
Miniature Rectangular / #20 Contacts / .040" Dia. / 7.5 Amps
MRE Series
Lock Tabs (MRE-V shown)
HOODS - LOCKING
Lever & Pivot Assemblies (MRE-VL shown)
Vibration Locks*
Vibration locks offer simplicity of design and
positive locking in excess of 50G shock impact
and 10G vibration acceleration. Mating halves
automatically lock when engaged. To unlock,
MRA 9, 14, 20, depress the levers. Drilled holes in the levers
are provided for safety wiring. Vibration
locks are available separately for assembly
on connectors now in service. Each code
number indicates two units: two levers with
two pivots, and two lock tabs.
34, 41, 42, 66
*US Patent Number 2760174
Lever
Used on
Lock Tabs
& Pilot (See Note) Connectors
Assembly
MRE-VL
MRE-VL2
MRE-V
MRE-V2
MRE 50,75
Note: When panel mounting the lock-tab half of a MRE 34, MRE 42 or MRE 50 and MRE 66 connector, flat washers
(.033 minimum thickness) should be used on the mounting screws to shim the molding away from the panel.
DIMENSIONS / OUTLINE
MOUNTING BRACKETS
H
Code No.
A
B
C
DIMENSIONS
D E F G
Wt.
Oz.
H
.128 Dia 3 Holes
MRE 50B 1.06 .688 3.031 3.44 .13 .28 .78 (No. 4 Mounting
Screw)
.4
.150 Dia 3 Holes
MRE 75B 1.48 1.047 3.062 3.56 .14 .30 1.14 (No. 6 Mounting
Screw)
.6
F
A
B
G
E
C
2.625
D
Panel
Opening
MRE 50 and MRE 75 connectors use
the standard MRE 50 and MRE 75
mounting brackets
.11R
DIMENSIONS / OUTLINE
PRE-SHAPED NYLON
POTTING FORMS
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Potting Form
Code No.
MRE 7 FM
MRE 8 FM
MRE 9 FM
MRE 14 FM
MRE 18 FM
MRE 20 FM
MRE 21 FM
MRE 26 FM
MRE 34 FM
MRE 41 FM
MRE 42 FM
MRE 50 FM
MRE 75 FM
Fig.
3
2
3
2
2
2
3
2
1
2
1
1
1
the connector after potting. Because of
floating contacts, connector halves should
always be engaged during the potting
operation to preserve contact alignment.
Each form matches the back opening contour
of its appropriate shell, and stays easily in
place during the potting operation. Of
negligible weight, it need not be removed from
Dimensions
A
B
.62
.46
.77
.93
.87
1.12
1.68
1.18
1.38
2.18
1.69
1.97
1.98
.43
.43
.43
.49
.61
.49
.43
.61
.80
.49
.80
.80
1.16
Winchester/Retconn
A
A
A
B
B
B
.50 .63
Figure 1
.50 .63
.50 .63
Figure 2
Figure 3
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 42
Rack & Panel
Miniature Rectangular / #20 Contacts / .040" Dia. / 7.5 Amps
MRE Series
ORDERING INFORMATION
Omit steps not required
MRE
■ Step 1
■ Step 2
Insert Series
Code:
MRE
By adding “ML”
to the series
code, connector
is supplied with
diallyl phthalate
type SDG-F
and mil plated
contacts.
Example: MREML
Number of
Contacts:
7, 8, 9, 11,
14, 18, 20,
21, 26, 34,
41, 42, 50,
75, 104
■ Step 3
Contact
Designation:
P - Pin
S - Socket
When
ordering
molding less
hardware to
be used with
mono-jacks,
see note
below.
34
■ Step 4
Type of
Contact:
Blank =
Standard
Solder Cup
Straight
Dip Solder
.025" dia.:
D3 = .094"
D4 = .125"
D5 = .156"
For additional
lengths in 1/32"
increments,
contact
Winchester’s
Sales
Department.
■ Step 5
Guides and
Jackscrew
Locks:
(See bottom
Chart)
H
G
S
VL
■ Step 6
■ Step 7
■ Step 8
Hoods:
Vibration
Accessories:
H - Standard Locks:
FM - Potting
Top
V - Lock Tab
Forms.
Opening* V2 - Lock Tab
Cannot be
Used with
H1 - Standard
(Size 50
Hoods.
Side
& 75)
Opening
Request
VL - Lever & Pivot
availability
H8 - Large Top
Ass’y
informaOpening
VL2 - Lever & Pivot
tion.
H9 - Large Side
Ass’y (Size
Opening
50 & 75)
*For MRE 7, 8,
9, 14, 18 and 20,
JTC hardware
may not be used
with H hoods.
Use H8 hoods.
■ Step 9
Special
Options:
Consult Sales
Department
■ Step 5
Guides
*G
Phosphor Bronze Cylindrical Guides*
*K
Beryllium Copper Cylindrical Guides
*N
Brass Cylindrical Guides*
Guides are not recommended for Size 104
“P” indicates two guide pins or two jackscrews
(Ex. JTCP)
“S” indicates two guide sockets or two jacksockets.
(Ex. GS)
Jackscrew Locks
***J
Polarized Fixed Jackscrew and Jacksocket
JT
Polarized Short Turning Jackscrew
and Jacksocket
JTC
Polarized Long Turning Jackscrew
and Jacksocket
Polarized Long Turning Mono-Jackscrew and
*** JTD
Mono-Jacksocket for Sizes 34, 42, 50, 75,
and 104 only.
** JZ
** JTW
** JTU
** JTX
** JTCW
** JTCU
** JTCX
Same as J but with 6-32 mtg. thd. (Not
available 5-3, 8) (Std. on 104)
Same as JT but with knurled round knob
with internal hex (not avail. 5-3, 8, 104)
Same as JT but with knurled round knob
with screwdriver slot (not avail. 5-3, 8, 104)
Same as JT but with hex knob (not avail. 53, 8, 104)
Same as JTC but with knurled round knob
with internal hex (not avail. 5-3, 8, 104)
Same as JTC but with knurled round knob
with screwdriver slot (not avail. 5-3, 8, 104)
Same as JTC but with hex knob (not avail.
5-3, 8, 104)
Same as JTC but with prybar knob.
** JTCZ
** Request availablity information.
*** Material: Nickel-plated brass - standard
Example: MRE34SJTDBH8
* For passivated stainless steel add SS suffix (Example: MRE34SGSS)
Mounting Note: Connectors MRE 41, MRE 26, and smaller use guides for mounting in a hood or on a panel.
Connectors MRE 34, MRE 42, MRE 50, MRE 75, use four #4 machine screws, in addition to guides, for
mounting in a hood or on a panel.
Note:
When ordering hoods, hardware and connectors separately for use with JTD Monojacks, connectors must be ordered as follows:
Pin connector = MRE34P8, MRE42P8, etc.
Socket connector = MRE34S8, MRE42S8, etc.
The number “8” indicates special housing for use with the JTD Monojack hardware
(available on sizes 34, 42, 50, 66, 75 and 104).
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 43
Rack & Panel
XMRA & XMRE Series External Miniature Rectangular / #16 Contacts / .062" Dia.
13 Amps ■ #20 Contacts / .040" Dia. / 7.5 Amps
A typical Series “XMRE” Receptacle and Plug fully wired and potted.
The XMRE and XMRA Series connectors are
designed to provide a sturdy, space-saving,
lightweight electrical connection. Inserts are
housed in protective shells with screw lock
coupling plus wall and cable mounting
accessories available.
Current Rating:XMRA - 13 amps
XMRE - 7.5 amps
No. of
Contacts:
XMRA - 9, 14, 20, 34, 42, 50,
50-8, 66, 75, 104
XMRE - 9, 14, 18, 20, 26, 34,
42, 50, 75, 104
Pin Contacts: XMRA - .062 diameter, gold
plated brass
XMRE - .040 diameter, gold
plated brass
Socket
Contacts:
Phosphor bronze plated gold.
Termination
Types:
XMRA - .070 dia. solder cup
will accept up to #16 AWG
stranded wire.
XMRE - .048 dia. solder cup
will accept up to #20 AWG
stranded wire.
Electrical Data: Both XMRE and XMRA meet
high potential performance
requirements of MIL-C-28748.
Military versions are QPL’d to
M28748/1 and M28748/2
(XMRA) and to M28748/5 and
M28748/6 (XMRE)
The minimum dielectric
withstanding voltage is one
minute electrification at 1000
VAC (sea level) for XMRA and
1200 VAC for XMRE Series.
Dielectric:
SPECIFICATIONS
Polarization:
Hoods:
Brown mineral filled diallyl
phthalate. Also available in
gray glass filled diallyl
phthalate, per MIL-M-14,
SDG-F.
A polarizing stud in the plug
shell and a mating slot in the
receptacle shell eliminates
misalignment. Jackscrews
and jacksockets or guide
pins and sockets are
alternative methods of
polarization.
Anodized Aluminum. May be
applied to both plug and
receptacles. Both top and
side opening hoods are
available.
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 44
Rack & Panel
XMRA & XMRE Series External Miniature Rectangular / #16 Contacts / .062" Dia.
13 Amps ■ #20 Contacts / .040" Dia. / 7.5 Amps
CONNECTOR ASSEMBLIES
CONNECTOR TERMS
Plug: The complete connector half which has
the plug shell as part of its assembly.
Receptacle: The complete connector half
which has the receptacle shell as part of its
assembly.
Shell: The metal housing in which a male or
female insert is assembled. A shell is either a
plug shell or a receptacle shell.
Plug Shell: One which is designed to be
inserted into a receptacle shell.
Receptacle Shell: One which is designed to
receive and enclose the plug shell upon
engagement.
Male Insert: The molded insulator body
containing pin contacts.
Femal Insert: The molded insulator body
containing socket contacts.
Winchester/Retconn
Pin Contacts: Male metal conductors that fit
into the socket contacts.
Socket Contacts: Female metal conductors,
tubular in shape, which receive the pin
contacts and retain them by spring tension.
Polarization: A means of controlling the
engagement of a plug and receptacle so that
correct mating of the contacts is achieved.
Potting Form: A plastic mold used to retain
and shape the sealing compound during the
moisture-proofing, or potting operation.
Potting: A method of moisture-proofing the
back of a plug or receptacle and the soldered
wire connections by injecting a free flowing
sealing compound into a pre-shaped form and
allowing it to set. The result is a homogeneous mass, chemically bonded to the back
of the insert and around the soldered
connections.
Accessories: Those components such as
hoods, mounting plates and finger grips which
are attachable to a plug or receptacle to
facilitate mounting and/or handling of the
connector.
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 45
Rack & Panel
XMRA & XMRE Series External Miniature Rectangular / #16 Contacts / .062" Dia.
13 Amps ■ #20 Contacts / .040" Dia. / 7.5 Amps
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Contact Arrangements
.075
Typ.
.38
.44
.075
Typ.
.56
.075
Typ.
1.250
.06
.06
.13R
9 Contacts
XMRE 9 or XMRA9
.13R
.09R
.130 Typ.
.09R
.172 Typ.
.130 Typ.
14 Contacts
XMRE 14 or XMRA 14
18 Contacts
XMRE 18
20 Contacts
XMRE 20 0r XMRA 20
.75
.75
.88
.09R
.23
.075
Typ.
.47
.16
2.000
2.000
.09R
.075
Typ.
.16
1.625
.23
.09R
.075
Typ.
.075
Typ.
1.312
.75
.75
.47
.23
.47
.23
.09R
.13R
.130 Typ.
.47
.075
Typ.
.09R
1.563
1.000
.937
.11
.56
.44
1.313
1.250
1.313
1.000
.075
Typ.
.09R
2.313
2.594
1.688
1.688
.06
2.000
2.281 2.719
.13R
.130 Typ.
.16
Mounting
holes for
No. 4 machine
screws
26 Contacts
XMRE 26
.180 Typ.
Mounting
holes for
No. 4 machine
screws
34 Contacts XMRA 34
.180 Typ.
34 Contacts XMRE 34
.180 Typ.
Mounting holes for
Mounting
No. 4 machine screws
holes for
No. 4 machine
screws
42 Contacts
XMRE 42 or XMRA 42
.180 Typ.
50 Contacts
XMRE 50 or XMRA 50
1.234
1.125
.50
.25
1.125
.50
.25
1.109
1.531
.88
.44
.075
Typ.
.150
Typ.
.130
Typ.
.77
.23
.31R
.075
Typ.
.260
.16
.13
2.594
2.281
1.969
2.375
1.969
2.281
2.282
2.719
2.750
.16
Mounting
holes for
No. 4
machine
screws
.180 Typ.
.225
58 Contacts
XMRA 50-8
Mounting
holes for No. 4
machine screws
66 Contacts
XMRA 66
.180 Typ.
.180 Typ.
.16R
Mounting
holes for No. 4
machine screws
75 Contacts
.180 Typ.
XMRE 75 or XMRA 75
104 Contacts
XMRA 104
XMRE 104
Views are rear (wiring end) of female inserts (male inserts are mirror image). The spacing, arrangement, and
identification of contacts of the XMRE inserts are the same as found on the Series MRE Connectors for the
same number of contacts.
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 46
Rack & Panel
XMRA & XMRE Series External Miniature Rectangular / #16 Contacts / .062" Dia.
13 Amps ■ #20 Contacts / .040" Dia. / 7.5 Amps
JACKSCREWS & JACKSOCKETS
Jackscrew Locking Devices
Type C (long-turning jackscrews and
jacksockets) or Type D (monojacks) must be
specified if both jackscrews and hood are
required on the same connector half.
Monojacks eliminate the need for roll pins,
spacers and washers.
Polarized jackscrews offer the ease and
assurance of threaded positive coupling.
They are particularly desirable for the larger
connectors (XMRE 34 and larger) whenever
they are to be used in locations that make it
difficult to apply enough direct pull to
separate the two halves of the connector.
OUTLINE
MonoJackscrew
Shell
A
.73
Jacksocket
B
4-40 UNC
Except
size 104
which is 632
Jackscrew
Hood
6-32 UNC Except 104
Which is 8-32 UNC
AND
Mating connector half with turnable
Jackscrews-with-Knobs
Code designation: M
Connector with fixed Jackscrews
Code designation: F
Self locking
pin
MonoJacksocket
.052 Dia.
safety wire hole
Code designation: C-0300, C-0400
OR
Mating connector half with Hood and
turnable Monojacks
Code designation: D-0300, D-0400
OR
Mating connector half with Hood and
turnable Long Jackscrews-withKnobs
Drawings show extension of knobs beyond shell (left) and beyond hood. Refer to details
of shells and hoods for the other dimensions which vary according to connector size.
DIMENSIONS
Dimension A
SERIES CODE
XMRE
Dimension B
9
14 18 20 26 34 42 50 50-8 66
0300
–
–
–
– .77
0300X .53 .53 .78 .53 .55
0400 .55 .55 .55 .55 .55
0400X –
–
– .55 .55
XMRA
0700
0800
Part
Jackscrews
Jacksockets
Jackscrews
Jacksockets
Jackscrews
Jacksockets
Knobs (except
Monojacks
Monojackscrews
Monojacksockets
–
–
–
–
–
–
–
–
–
–
CODE 34 42 50 66 75 104
0300
0400
0700
0800
.58
.58
.58
.58
.53
.53
.53
.53
.53
.53
.53
.53
–
–
–
–
–
–
–
–
.52
.52
.52
.52
–
–
–
–
.58
.58
–
–
–
–
.64
.64
.64
.64
–
–
.52
.52
Code
Letter
Wt. Oz.
See Notes
1&2
Turntable M
Long
Turntable C
0.30
0.45
stainless steel
with passivating dip
stainless steel
with passivating dip
Fixed
0.15
nickel-plated brass
F
75 104
Material and
Finish
al. anodized
Turning
Turning
D
Guide Socket
Code Letter
.55
.55
–
–
–
–
.38
.38
.53
.53
–
–
–
–
.38
.38
Actual Size Photo
G Type
For General Use
K
K Type For
High Electrical Conductivity
N
MATERIALS
"G" Socket:
Winchester/Retconn
.55
.55
–
–
G
nickel-plated brass
Note 1: Weights are given for pairs, i.e., for a jackscrew and a
jacksocket, etc., so that the weight figure may be added once to the
weights of other accessories when computing the total weight of a plug
or receptacle.
Note 2: Weights of turnable jackscrews and turnable jacksockets include
knobs and roll pins; weights of fixed hardware include nuts.
.59
.59
–
–
"K" Socket:
"N" Socket:
Guide Pin:
Standard Guide Pin
mates with all types
N Type For
Extra Mechanical Strength
Phosphor
bronze.
Beryllium copper.
Brass.
Brass
FINISH
Gold over Nickel
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 47
Rack & Panel
XMRA & XMRE Series External Miniature Rectangular / #16 Contacts / .062" Dia.
13 Amps ■ #20 Contacts / .040" Dia. / 7.5 Amps
OUTLINE
JACKSCREW & JACKSOCKETS
.19
.50
.22
.22
Dia.
.25 Hex.
.078 Int. Hex
A
A
A
A
CW
CU
CX
CZ
.19
.22 Dia.
.078 Int. Hex
.97
.33
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.25
Hex
MU
MW
6-32 UNC 2 THD. (Typ)
.73
.23
FZ
MX
DIMENSIONS
All jackscrews and sockets are stainless
steel, passivated, except F & D which
are nickel-plated brass.
All knobs are aluminum, anodized
except MW and CW which are
stainless steel, passivated.
Jackscrew Locking For Series XMRE, XMRA
Size 0300 0400 0300X 0400X 0700 0800
9
14
18
20
26
34
42
50
50-8
66
75
–
–
–
–
.36
.39
.34
.34
–
–
.33
Dimension A - Type CW
.36
.34
.36
–
.36
.34
.36
–
.36
.34
.36
–
.36
34
.36
–
.36
.36
.36
–
.39
.39
.39
.47
.34
.34
.34
–
.34
.34
.34
–
–
–
–
.47
–
–
–
.47
.33
.33
.33
–
–
–
–
–
–
.47
–
–
.47
.47
–
Size 0300 0400 0300X 0400X 0700 0800
Winchester/Retconn
9
14
18
20
26
34
42
50
50-8
66
75
–
–
–
–
.77
.52
.47
.47
–
–
.45
Dimension A - Type CX
.48
.47
.48
.48
.47
.48
.48
.72
.48
.48
.47
.48
.48
.48
.48
.52
.52
.52
.47
.47
.47
.47
.47
.47
–
–
–
–
–
–
.45
.45
.45
–
–
–
–
–
.61
–
–
.61
.61
–
–
–
–
–
–
.61
–
–
.61
.61
–
Size 0300 0400 0300X 0400X 0700 0800
9
14
18
20
26
34
42
50
50-8
66
75
–
–
–
–
.61
.64
.59
.59
–
–
.58
Dimension A - Type CU
.61
.59
.61
.61
.59
.61
.61
.59
.61
.61
.59
.61
.61
.61
.61
.64
.64
.64
.59
.59
.59
.59
.59
.59
–
–
–
–
–
–
.58
.58
.58
–
–
–
–
–
.72
–
–
.72
.72
–
–
–
–
–
–
.72
–
–
.72
.72
–
Size 0300 0400 0300X 0400X 0700 0800
9
14
18
20
26
34
42
50
50-8
66
75
–
–
–
–
.92
.64
.59
.59
–
–
.58
Dimension A - Type CZ
.61
.59
.61
.61
.59
.61
.61
.84
.61
.61
.59
.61
.61
.61
.61
.64
.64
.64
.59
.59
.59
.59
.59
.59
–
–
–
–
–
–
.58
.58
.58
–
–
–
–
–
.72
–
–
.72
.72
–
–
–
–
–
–
.72
–
–
.72
.72
–
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 48
Rack & Panel
XMRA & XMRE Series External Miniature Rectangular / #16 Contacts / .062" Dia.
13 Amps ■ #20 Contacts / .040" Dia. / 7.5 Amps
DIMENSIONS
HOODS - DRAWN ALUMINUM
D
.08
Dimensions are for reference only and are subject to change. Outline drawings on request.
.191 Dia. 2 Holes (.228 Dia. For
XMRA 104-0800 Only)
.1935 Dia. 2 Holes (.228 Dia. For
XMRA 104-0700 Only)
Style
“Y”
C
E
(cable opening)
G
A
Style
“Z”
.08
D
H
B
C
G
B
.08
Top Cable Opening
A
Side Cable Opening
Hood
Part Number
A
For use with XMRA 34-0700
Type C
XMRA 50-8-0700
Jacksockets & XMRA 66-0700
Jackscrews
2.09
2.38
2.38
XMRA 104-0700
2.84
For use with XMRA 34-0700D
2.09
Type D
XMRA 50-8-0700D 2.38
Jacksockets & XMRA 66-0700D
2.38
Jackscrews XMRA 104-0700D 2.84
For use with
G, K, or N, Type
Guides or Type
F Jackscrews
E
(cable
opening)
XMRA 34-0900
XMRA 50-8-0900
XMRA 66-0900
XMRA 104-0900
2.09
2.38
2.38
2.84
B
Dimensions
C
D
Hood
E
G
.84
1.22
1.22
1.63
.84
1.22
1.22
1.63
1.17
1.17
1.17
2.23
1.17
1.17
1.17
2.23
1.59
1.69
1.69
2.75
1.59
1.69
1.69
2.75
.66x.75
1.03D
1.03D
1.19D
.66x.75
1.03D
1.03D
1.19D
1.688
1.969
1.969
2.375
1.688
1.969
1.969
2.375
.84
1.22
1.22
1.63
1.17
1.17
1.17
2.23
1.59
1.69
1.69
2.75
.66x.75
1.03D
1.03D
1.19D
–
–
–
–
For use with
Type C
Jacksockets &
Jackscrews
Part Number
XMRA 34-0800
XMRA 50-8-0800
XMRA 66-0800
XMRA 104-0800
For use with XMRA 34-0800D
Type D
XMRA 50-8-0800D
Jacksockets & XMRA 66-0800D
Jackscrews XMRA 104-0800D
For use with XMRA 34-0200
G, K, or N, Type XMRA 50-8-0200
Guides or Type XMRA 66-0200
F Jackscrews XMRA 104-0200
A
B
2.09
2.38
2.38
2.84
2.09
2.38
2.38
2.84
2.09
2.38
2.38
2.84
.84
1.22
1.22
1.63
.84
1.22
1.22
1.63
.84
1.22
1.22
1.63
Dimensions
C
D
E
1.16
1.16
1.16
2.22
1.17
1.17
1.17
2.23
1.16
1.16
1.16
2.22
2.58
2.91
2.91
3.38
2.58
2.91
2.91
3.38
2.58
2.91
2.91
3.38
.64x.75
.84 D
.84D
1.19D
.64x.75
.84D
.84D
1.19D
.64X.75
.84D
.84D
1.19D
H
G
1.06
1.34
1.34
1.63
1.688
1.969
1.969
2.375
1.06
1.34
1.34
1.63
1.688
1.969
1.969
2.375
1.06
1.34
1.34
1.63
–
–
–
–
DIMENSIONS
HOODS - FORMED ALUMINUM
For use
with
Monojacks
For use with
For use with
Type C
G, K, or N, Type
Jacksockets &
Guides *
Jackscrews
Hood Part No.
(If ordered separately)
XMRE 9-0300X
XMRE 14-0300X
XMRE 18-0300X
XMRE 34-0300D
XMRE 34-0300XD
XMRE 42-0300D
XMRE 42-0300XD
XMRE 50-0300D
XMRE 50-0300XD
XMRE 75-0300D
XMRE 75-0300XD
For use
with
Monojacks
XMRE 34-0400D
XMRE 34-0400XD
XMRE 42-0400D
XMRE 42-0400XD
XMRE 50-0400D
XMRE 50-0400XD
XMRE 75-0400D
XMRE 75-0400XD
XMRE 20-0300X
XMRE 26-0300
XMRE 26-0300X
XMRE 34-0300
XMRE 34-0300X
XMRE 42-0300
XMRE 42-0300X
XMRE 50-0300
XMRE 50-0300X
XMRE 75-0300
XMRE 75-0300X
XMRE 9-0500
XMRE 9-0500X
XMRE 14-0500
XMRE 14-0500X
XMRE 18-0500
XMRE 18-0500X
XMRE 20-0500
XMRE 20-0500X
XMRE 26-0500
XMRE 26-0500X
XMRE 34-0500
XMRE 34-0500X
XMRE 42-0500
XMRE 42-0500X
XMRE 50-0500
XMRE 50-0500X
XMRE 75-0500
XMRE 75-0500X
For use with
For use with
Type C
G, K, or N, Type
Jacksockets &
Guides *
Jackscrews
Hood Part No.
(If ordered separately)
XMRE 9-0400
XMRE 9-0400X
XMRE 14-0400
XMRE 14-0400X
XMRE 18-0400
XMRE 18-0400X
XMRE 20-0400
XMRE 20-0400X
XMRE 26-0400
XMRE 26-0400X
XMRE 34-0400
XMRE 34-0400X
XMRE 42-0400
XMRE 42-0400X
XMRE 50-0400
XMRE 50-0400X
XMRE 75-0400
XMRE 75-0400X
XMRE 9-0600
XMRE 9-0600X
XMRE 14-0600
XMRE 14-0600X
XMRE 18-0600
XMRE 18-0600X
XMRE 20-0600
XMRE 20-0600X
XMRE 26-0600
XMRE 26-0600X
XMRE 34-0600
XMRE 34-0600X
XMRE 42-0600
XMRE 42-0600X
XMRE 50-0600
XMRE 50-0600X
XMRE 75-0600
XMRE 75-0600X
A
1
1
.75
.75
.75
.75
.75
.75
1.28
1.28
1.25
1.25
1.30
1.30
1.30
1.30
1.31
1.31
B
C
1.31
1.30
1.19
1.05
1.19
1.25
1.19
1.05
1.72
1.78
1.67
1.75
1.73
1.80
1.80
1.80
1.75
1.86
1.31
1.31
1.25
1.25
1.31
1.31
1.56
1.56
1.63
1.63
2
2.00
2.31
2.31
2.59
2.59
2.59
2.59
Top Cable Opening
Cable
Opening
Dimensions
D
E
Dia.
.44
.44
.5
.5
.63
.63
.5
.5
.64
.64
.83
.83
.83
.83
.83
.83
1.19
1.19
.31
.59
.44D
.59
.44D
.63
.44D
.66
.59
.78
.66D
1.06
.63D
1.06
.63D
1.06
.63
1
F
Dia.
–
.31
–
.38
–
.44
–
.38
.38
.44
–
.56
–
.56
–
.28
.88
.88
E & F (cable opening)
0.3
D
A
F
0.3
0.4
0.3
E
C
0.4
0.6
0.7
Drilled for long jackscrews
and jacksockets (type C) in
Hood style 0300 only
B
0.8
1.0
Side Cable Opening
Cable
Opening
Dimensions
0300X & 0500X
Style Cable Clamp
Wt.
Oz.
F
A
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.28
1.25
1.25
1.30
1.30
1.30
1.30
1.31
1.31
B
C
D
E
Dia.
1.31
1.31
1.25
1.25
1.31
1.31
1.56
1.56
1.63
1.63
2
2
2.31
2.31
2.59
2.59
2.59
2.59
1.63
1.61
1.69
1.55
1.75
1.81
2
1.86
2.06
2.13
2.42
2.5
2.73
2.81
3.02
3.09
3.02
3.14
.44
.44
.5
.5
.63
.63
.5
.5
.64
.64
.83
.83
.83
.83
.83
.83
1.19
1.19
.31D
.59
.38D
.59
.44D
.69
.38D
.66
.59
.78
.66
.81
.63
.84
.63
1.06
.63
1
F
Dia.
–
.31
–
.38
–
.44
–
.38
.38
.44
–
.56
.5
.56
.5
.56
.88
.88
Wt.
Oz.
E
C
0.3
E & F (cable opening)
B
0.3
0.3
0.3
0.4
A
0400X & 0600X
Style Cable Clamp
0.6
0.7
0.8
1.0
* Add “J” to hood P/N when used with “F” jackscrews.
Winchester/Retconn
3DUN5RDG([W6XLWH0LGGOHEXU\&RQQHFWLFXW Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 49
D
Rack & Panel
XMRA & XMRE Series External Miniature Rectangular / #16 Contacts / .062" Dia.
13 Amps ■ #20 Contacts / .040" Dia. / 7.5 Amps
OUTLINE
SHELLS - RECEPTACLE
Dimensions are for reference only and are subject to change. Outline drawings on request.
.06R
B
C
.03R
B
C
.20R
B
C
.06R
.14R
Mtg Hole
Style 9
F
.421R
B
C
.384R
.120 Dia.
B
C
.28
ED
ED
A
E
B
A F
C
G
D
ED
ED
ED
.156 Typ
.06R
.06R
.06R
.06R
.06R
.312 Typ
Polarizing Slot
.120 Dia.
2 Holes
For All Conf.
.14R
G
.500
.114
G
For 9 to 26
For 34, 42, and
50
.120 Dia.
6 Holes .114
.140 Dia.
4 Holes
.117
.383
.766
For 66 and 50-8
.120 Dia.
4 Holes
G
.875
For 75
.150 Dia.
6 Holes
For 104
DIMENSIONS
SHELLS - RECEPTACLE
Important Note When Ordering
Plug and Receptacle Shells
The shell part numbers given in table
show an asterisk (*) where the code
letter for the desired polarizing
position belongs - example: XMRE92*000 becomes XMRE9-2B000 when
polarization in position “B” is desired.
Specify the same position on the
mating shell.
For non-polarized shells, merely omit
this position, e.g. XMRE9-2000.
TYPICAL SHELLS FOR
MONOJACKS
Shells are aluminum, anodized for
protection against corrosion. Either
shell style - plug or receptacle - may be
used to house the female insert, thus
allowing the “live” socket contacts to be
cable or panel mounted, as desired.
Shells also provide a means by which
connector polarization is accomplished
- the receptacle shell is slotted for
engaging a polarizing pin on the plug
shell. Any of seven positions (A, B, C,
D, E, F, or G) may be specified for
polarization; non-polarized shells have
the slot and pin omitted.
Stainless steel shells available for 66
and 104 sizes. Dimensions vary from
those shown for aluminum shells,
Check Sales for availability and
dimensions on all sizes.
For Connector Size
A
34, 42, 50, 50-8, 66, 75 .11
104
.14
B
C
.120 .06R
.150 .07R
Winchester/Retconn
Shell Part No.
(if ordered
separately)
XMRE 9-2*000
XMRE 14-2*000
XMRE 18-2*000
XMRE 20-2*000
XMRE 26-2*000
XMRE 34-2*000
XMRE 34-4*000
XMRE 42-2*000
XMRE 42-4*000
XMRE 50-2*000
XMRE 50-4*000
XMRA 66-2*000
XMRA 66-4*000
XMRA 50-8-2*000
XMRA 50-8-4*000
XMRE 75-2*000
XMRE 75-4*000
XMRA 104-2*000
XMRA 104-4*000
Dimensions
C
D
E
F
G
Wt.
Oz.
.88
.81
.88
1.13
1.19
.66
.66
.66
.66
.66
–
–
–
–
–
0.15
0.16
0.17
0.19
0.23
.75
1.687 1.44
.66
.234 0.25
2.45 .89
.75
2.000 1.75
.66
.234 0.28
2.86 1.02
.75
2.282 2.03
.66
.234 0.30
2.42 1.27 1.13 1.969 1.72
.66
.250 0.28
2.86 1.38 1.11 2.282 2.03
.66
2.91 1.69 1.48 2.375 2.13
.66
A
B
1.45
1.39
1.45
1.70
1.77
.52
.58
.70
.58
.70
.38
.45
.58
.45
.58
1.000
.937
1.000
1.250
1.312
2.14 .89
B Dia.
4 Corner
Holes
C Type
A
2 Slots
For 34, 42, 50, 50-8, 66
and 104 Configuration
B Dia.
4 Corner
Holes
A
–
0.32
.437 0.30
C Type
4 Slots
For 75
Configuration
Receptacle Shell
Style Number 2000
Shells are .040 in. thick.
199 Park Road Ext., Suite 104, Middlebury, Connecticut 067622 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 50
Rack & Panel
XMRA & XMRE Series External Miniature Rectangular / #16 Contacts / .062" Dia.
13 Amps ■ #20 Contacts / .040" Dia. / 7.5 Amps
OUTLINE
SHELLS - PLUG
Dimensions are for reference only and are subject to change. Outline drawings on request.
B
C
.140 Dia. 4 Holes
B
C
.06R
B
C
B
C
.120 Dia.
.03R
.06R
.14R
Mtg. Hole
Style 9
F
B
C
D E
.508
D E
D E
.06R
A
E
B
F
A
C
G
D
D E
.06R
.06R
D E
.06R
.156 Typ.
.06R
.312 Typ.
.150 Dia.
6 Holes
G
.120 Dia.
4 Holes
.421R
.875
For 104
.117
.383
.766
.20R
.120 Dia.
6 Holes
For 75
G
.500
.120 Dia.
6 Holes
.372R
For 66 and 50-8
G
.468
.14R
For 34, 42, and 50
.120 Dia.
2 Holes
Polarizing Pin
For 9 to 26
For All Config.
DIMENSIONS
Shell Part No.
(if ordered
separately)
XMRE 9-1*000
XMRE 14-1*000
XMRE 18-1*000
XMRE 20-1*000
XMRE 26-1*000
XMRE 34-1*000
XMRE 34-3*000
XMRE 42-1*000
XMRE 42-3*000
XMRE 50-1*000
XMRE 50-3*000
XMRA 66-1*000
XMRA 66-3*000
XMRA 50-8-1*000
XMRA 50-8-3*000
XMRE 75-1*000
XMRE 75-3*000
XMRA 104-1*000
XMRA 104-3*000
F
G
Wt.
Oz.
.88
.81
.88
1.13
1.19
.63
.63
.63
.63
.63
–
–
–
–
–
0.14
0.15
0.16
0.18
0.22
.75
1.687 1.44
.66
.234
0.24
.88
.75
2.000 1.75
.66
.234
0.26
1
.75
2.282 2.03
.66
.234
0.28
2.41 1.25 1.13 1.969 1.72
.66
.250
0.28
2.84 1.36 1.11 2.282 2.03
.66
–
0.30
2.88 1.66 1.48 2.375 2.13
.66
.437
0.30
B
1.44
1.38
1.44
1.69
1.75
.5
.56
.69
.56
.69
.38
.45
.58
.45
.58
1.000
.937
1.000
1.250
1.312
2.13
.88
2.44
2.84
B Dia.
4 Corner
Holes
C Type
Typical Shells
For Monojacks
For Connector Size
Dimensions
C
D
E
A
A
34, 42, 50, 50-8, 66, 75 .11
104
.14
B
C Type
C
.120 .06R
.150 .07R
4 Slots
A
For 75
Configuration
Winchester/Retconn
B Dia.
4 Corner
Holes
2 Slots
A
For 34, 42, 50, 50-8, 66
and 104 Configuration
Plug Shell
Style Number 1000
Shells are .040 in. thick.
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 51
Rack & Panel
XMRA & XMRE Series External Miniature Rectangular / #16 Contacts / .062" Dia.
13 Amps ■ #20 Contacts / .040" Dia. / 7.5 Amps
OUTLINE
MOUNTING PLATES
Dimensions are for reference only and are subject to change. Outline drawings on request.
A
B
Mounting Plates for External Miniature Rectangular Connectors,
Potting Forms
.16R
Mounting Plates enable attachment of a connector to a wall, bulkhead, or other supporting
surface. The plate is assembled to the back of a plug or receptacle by employing the same
hardware and/or guides used to retain the insert in the shell; No. 4 machine screws are
then used to mount the complete assembly against the required surface.
Mounting plates are aluminum, anodized to resist corrosion.
.06R
D
E
F
.125 Dia.
4 Holes
C
.040 Stock
G
Mounting plate plan view for 9 to 26 contacts
A
B
C
.125 Dia.
10 Holes
.125 Dia. (66 & 50-8)
.150 Dia. (104)
10 Holes
B
C
.125 Dia.
12 Holes
.06R
.23
H
.383
.06R
F
D
E
F
D
.117
.16R
E
H Dimension
Panel Cut Out
50-8 = .250
66 = .250
104 = .437
G
.040 Stock
Left half shows holes for 34, 42, 50 contacts; right half for 75 contacts
only. Each plate is symmetrical about the indicated center line.
Panel Cut Out
G
A
.050 Stock
Mounting Plate Plan View for 50-8, 66 & 104 Contacts
Note: .19R for 104 and .16R for 50-8 & 66 for panel cutout.
DIMENSIONS
Mounting Plate Part
No. (If Ordered
Separately)
OUTLINE
POTTING FORMS
XMRE 9-0010
XMRE 14-0010
XMRE 18-0010
XMRE 20-0010
XMRE 26-0010
XMRE 34-0010
XMRE 42-0010
XMRE 50-0010
XMRE 75-0010
XMRA 50-8-0010
XMRA 66-0010
XMRA 104-0010
Dimensions
C
D
A
B
2.02
1.95
2.02
2.27
2.33
2.70
3.02
3.42
3.42
2.98
1.000
.937
1.000
1.250
1.312
1.687
2.000
2.281
2.281
1.969
.88
.81
.88
1.13
1.19
1.44
1.75
2.03
2.03
1.72
3.5
2.375
2.13
Panel
Cutout
E
F
G
Wt.
Oz.
.41
.47
.59
.47
.59
.75
.75
.75
1.11
1.13
.95
1.02
1.14
1.02
1.14
1.33
1.33
1.45
1.80
1.69
.64
.70
.83
.70
.83
1.02
1.02
1.14
1.48
1.39
1.58
1.52
1.58
1.83
1.89
2.27
2.58
2.98
2.98
2.55
0.09
0.10
0.11
0.12
0.14
0.15
0.16
0.18
0.19
0.18
1.48
2.0
1.81
3.03
0.19
Potting Forms for External Miniature
Rectangular Connectors
A
Nylon Potting Forms: Each form matches the
back opening contour of its appropriate shell.
Stays easily in place during the potting
operation. Of negligible weight, the form
need not be removed from the connector after
potting. XMRE and XMRA connector-halves
should always be engaged during the potting
operation to preserve the contact alignment.
B
Potting Form Part No.
(If Ordered Separately)
XMRE 9-0100
XMRE 14-0100
XMRE 18-0100
XMRE 20-0100
XMRE 26-0100
XMRE 34-0100
XMRE 42-0100
XMRE 50-0100
XMRE 75-0100
Dimensions
A
B
.38
.45
.56
.44
.56
.75
.75
.75
1.11
.86
.81
.86
1.11
1.17
1.39
1.69
1.98
1.98
.50
B
.025 Typ. Wall Thick
Potting form plan view
for 9 to 26 contacts
DIMENSIONS
Winchester/Retconn
A
Potting Form Part No.
(If Ordered Separately)
XMRA 9-0100
XMRA 14-0100
* XMRA 20-0100
XMRA 34-0100
XMRA 42-0100
XMRA 50-0100
XMRA 50-8-0100
XMRA 66-0100
XMRA 75-0100
XMRA 104-0100
Potting form plan view for 34, 42,
50, 50-8, 66, and 104 contacts
Dimensions
A
B
.38
.45
.44
.75
.75
.75
1.13
1.13
1.11
1.48
.86
1.11
1.11
1.39
1.69
2.03
1.72
1.72
2.03
2.08
*Stepped
construction not
shown or
dimensioned.
Cut-outs to clear
XMRA barriers not
shown.
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 52
Rack & Panel
XMRA & XMRE Series External Miniature Rectangular / #16 Contacts / .062" Dia.
13 Amps ■ #20 Contacts / .040" Dia. / 7.5 Amps
ORDERING INFORMATION
Omit steps not required
■ Step 1
■ Step 2
Insert Code Pin or
Socket
No. of
Contacts:
Contacts:
P - Pin
XMRA 9,
14, 20, 34,
S - Socket
42, 50, 50-8,
66, 75, 104
XMRE 9,
14, 18, 20,
26, 34, 42,
50, 75, 104
By adding “ML”
to the series
code, connector
is supplied with
diallyl phthalate
type SDG-F
and mil plated
contacts.
Example:
XMREML
XMRAML
■ Step 3
Type of
Contact:
Blank =
Standard
Solder Cup
Straight
Dip Solder
.030" dia.=
XMRA
.025" dia.=
XMRE
D3 = .094"
D4 = .125"
D5 = .156"
For additional
lengths in 1/32"
increments,
contact
Winchester’s
Sales
Department.
XMRE 34
S
-F
-2
A
1
10
XMRA 34
S
-F
-2
A
1
10
■ Step 4
■ Step 5
Guides
Jackscrews
and
Jacksockets
(See bottom
chart)
Shell Type:
0 No shell.
1 Plug shell, style
1*000.
2 Receptacle shell,
style 2*000.
3 Plug shell,
monojack type,
style 3*000.
4 Receptacle,
monojack type,
style 4*000.
7 Stainless Steel
Plug shell, style
7*000 (66 & 104
only)
8 Stainless Steel
Receptacle shell,
style 8*000 (66 &
104 only)
Polarizing Position
Request availablity
information.
**
**
■ Step 4
*
**
■ Step 7
■ Step 6
Polarization (See
bottom
Position:
A, B, C, D, E, chart)
F or G.
Omit letter
when
polarization is
not required.
Guides
G- Cylindrical guide with single spring member.
Recommended for ground only.
K- Cylindrical guide with four spring members.
May be used for electrical contact.
N- Cylindrical guide without spring member.
Recommended for extra mechanical strength.
Jackscrews and Jacksockets
***MPolarized short turnable jackscrew and
jacksocket. Cannot be used with hoods.
***CPolarized long turnable jackscrew and
jacksocket for use with hoods.
***DPolarized turnable jackscrew and jacksocket
for use with hoods for sizes 34 thru 104
excluding 41.
*** FPolarized fixed jackscrew and jacksocket.
***JNon-polarized short turnable jackscrews.
Cannot be used with hoods.
***LNon-polarized long turnable jackscrews.
***RNon-polarized fixed jacksocket.
***FZ- Same as F but with 6-32 mtg thd (std on 104).
***MW- Same as M but with knurled round knob with
internal hex (not avail. 104).
***MU- Same as M but with knurled round knob with
screwdriver slot (not avail. 104).
***MX- Same as M but with hex knob (not avail 104).
***CW- Same as C but with knurled round knob with
internal hex (not avail. 104).
***CU- Same as C but with knurled round knob with
screwdriver slot (not avail. 104).
***CX- Same as C but with hex knob (not avail. 104).
***CZ- Same as C but with prybar knob
(not avail. 104).
***
***
■ Step 8
Mounting Plate
or Finger Grips:
00- When no
mounting
plate is
required
*10- Mounting
plate, style
#0010.
*Mounting plates
are not used with
“M”, “C”, “D”, “J”,
or “L” jackscrews.
■ Step 9
Special Gaskets:
Omit letter when gaskets
are not required.
**
G- Bulkhead gasket, style
#0000G. Use only
when mounting plate is
specified.
**
F- Face gasket, style
#0000F. Use with
male insert only.
**
B- If both gasket #0000G
and gasket #0000F
are desired.
**
**
Check plant for availability
on all gaskets.
■ Step 7
Potting Form or Hoods:
0- When no potting form or hood is required.
1- Potting form style #0100. Cannot be used with hood.
Request availability information.
Cannot be used
Formed Hoods:
3- Hood, top opening, style #0300, for use with Type “C”
or “D” jackscrews.
4- Hood, side opening, style #0400, for use with Type “C”
or “D” jackscrews.
5- Hood, top opening, style #0500, for use with “G”, “K”,
or “N” type guides only and “F” style jackscrews.
6- Hood, side opening, style #0600, for use with “G”, “K”,
or “N” type guides only and “F” style jackscrews.
Deep Drawn Hoods:
7- Hood, top opening, style #0700, for use with Type “C”
or “D” jackscrews.
8- Hood, side opening, style #0800, for use with Type “C”
or “D” jackscrews.
9- Hood, top opening, style #0900, for use with “G”, “K”,
and “N” type guides or “F” jackscrews.
2- Hood, side opening, style #0200, for use with “G”, “K”,
or “N” type guides or “F” jackscrews.
Note: Addition of “X” to end of code # indicates cable
opening larger than std. See hoods for cable opening
size.
Example: XMRE34PD3A300X
Request availablity information.
Material: Nickel-plated brass - standard
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 53
Rack & Panel
SLE-SME-SRE Series
Sub Miniature / High Density Rectangular / .025" Dia. / 3 Amps
.030" Dia. / 5 Amps / .040" Dia. / 7.5 Amps
SLE
.025 Diameter Contacts —
3 Amps.
SRE
.030 Diameter Contacts — 5 Amps
Within this series, you’ll find a standard size
connector for which you can select one of
three current ratings: 3, 5 or 7.5 amps.
Compact and lightweight, they are especially
SME
.040 Diameter Contacts — 7.5 Amps
suited for aircraft, instrumentation and
portable equipment applications.
Right angle, dip solder, pin or socket contacts
are available. Consult factory.
SPECIFICATIONS
Current Rating:SLE - 3 amps: SRE - 5
amps; SME - 7.5 amps.
No. of
Contacts:
4, 5, 7, 9, 11, 14, 20, 26, 29,
34, 44, 50.
Pin Contacts: Brass, gold plated except for
SLE which is phosphor
bronze, gold plated.
Socket
Contacts:
Phosphor bronze, gold
plated.
Termination
Types:
.037 diameter solder cup will
accept up to #22 AWG
stranded wire. Solder cup
adaptor (Part No. S45) will
accept up to #20 AWG
stranded wire. Dip solder
terminations available for
SRE Series, .030 Dia.
Check Sales Department for
available lengths.
Military versions of SRE are
QPL’d to M28748/7 and
M28748/8.
Electrical Data:The dielectric withstanding
voltage is one minute
Dielectric:
Guides:
Jackscrews:
Hoods:
electrification at 1000 VAC.
Green glass-filled diallyl
phthalate per MIL-M-14,
SDG-F.
Type NSS stainless steel,
passivated or Type N Brass,
gold plated.
Stainless steel, passivated.
Aluminum knobs on the
jackscrews are equipped with
set screws, except JTU
jackscrews which have
stainless steel knobs
equipped with groove pins.
Anodized aluminum. May be
applied to either plug or
receptacle. Both top and side
openings are available
for use with either guides
or jackscrews.
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 54
Rack & Panel
SLE-SME-SRE Series
Sub Miniature / High Density Rectangular / .025" Dia. / 3 Amps
.030" Dia. / 5 Amps / .040" Dia. / 7.5 Amps
CONTACT ARRANGEMENT
Mating Face of Female Moldings - Male Moldings Reverse Image
Dimensions are for reference only and are subject to change. Outline drawings on request.
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 55
Rack & Panel
SLE-SME-SRE Series
Sub Miniature / High Density Rectangular / .025" Dia. / 3 Amps
.030" Dia. / 5 Amps / .040" Dia. / 7.5 Amps
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
J
D
C
F
F
K Dia.
E Dia.
A
B
.16
.037 Dia.
Solder Cup
N
Dia.
H
G
.24
2-56 UNC-2A THD.
.24
Slot — .020 Wide
Slot — .031 Wide
.81
Typ.
.22
Typ.
M
L THD.
.47
Typ.
.11
.11
1.57 Except Size 44 & 50
Which is 2.34
.11
N Dia.
N Dia.
N Dia.
.16
.16
.16
.032 Dia.
Hole
.037 Dia.
Solder Cup
L THD.
L THD.
L THD.
M
2-56
UNC-2A
.11
M
M
.46
Typ.
J Jackscrews
JT Jackscrews
JTU Jackscrews
JTC Jackscrews
DIMENSIONS
The stainless steel guide pin and socket have
good physical strength and are particularly
desirable for mounting connectors which will be
No. of
Contacts A
4
5
7
9
11
14
20
26
29
34
44
50
subject to severe vibration in service, but not for
electrical applications. Optional gold plated
brass available for electrical applications.
Series D
B
.78 .562
.70 .482
.78 .562
.88 .656
.78 .531
.88 .625
1.06 .814
1.25 1.000
1.34 1.094
1.25 1.032
1.48 1.267
1.63 1.408
C
.21
.21
.21
.21
.28
.28
.28
.28
.28
.39
.39
.39
E F G H J K
L Thd
M N
Dia
SLE .62 .08 .24 .10 .14 .59 .125 2-56 UNC* .15 .025
SRE .57 .09 .22 .11 .12 .57 .137 3-48 UNC* .12 .030
SME .62 .08 .24 .10 .14 .59 .125 2-56 UNC* .15 .040
*2-56 UNC Thread also available.
See ordering information for part number suffix.
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 56
Rack & Panel
SLE-SME-SRE Series
Sub Miniature / High Density Rectangular / .025" Dia. / 3 Amps
.030" Dia. / 5 Amps / .040" Dia. / 7.5 Amps
OUTLINE
Hoods Formed Aluminum
Dimensions are for reference only and are subject to change. Outline drawings on request.
E x F
Cable Opening
H
A
F
B
D
G
D
C
C
E
.22
B
H
Style H9 — Side Cable Opening
.22
Style H8 / H13 — Top Cable Opening
DIMENSIONS
Cable
Opening
Hood
Style
Hood Catalog
Number
Guides Only*
A
B
C
D
G
H
E
F
H8
H8
H9
H9
H13
H13
H13
H13
H13
SRE11H8
SRE50H8
SRE11H9
SRE50H9
SRE4&7H13
SRE14H13
SRE20H13
SRE26H13
SRE34H13
1.02
1.80
–
–
1.02
1.02
1.02
1.02
1.05
.72
1.50
.72
1.50
.75
.75
.75
.75
.75
.33
.45
.33
.45
.25
.34
.34
.34
.45
.78
1.63
.78
1.63
.78
.88
1.06
1.25
1.25
–
–
1.08
1.92
–
–
–
–
–
.53
.63
.53
.63
.53
.53
.53
.53
.63
.28
1.19
.50
1.19
.22
.25
.38
.41
.73
.28
.38
.22
.38
.16
.16
.25
.25
.38
H13
SRE29H13
1.02
–
.53
.41
.25
Dimensions
NOT AVAILABLE
ORDERING INFORMATION
*
■ Step 2
Number of
Contacts:
4, 5, 7, 9, 11, 14,
20, 26, 29, 34, 44,
50
Winchester/Retconn
.34
1.34
11
50
11
50
4&7
14
20
26
34
5
9
29
44
NOT AVAILABLE
Add “J” to hood part number when used with fixed jackscrews
Add “JTC” to hood part number when used with long turning jackscrews.
SRE
■ Step 1
Insert Code Series:
SLE- .025 Dia.
Contact
SME- .040 Dia.
Contact
SRE- .030 Dia.
Contact
.75
No. of
Conacts
■ Step 3
Contact
Designation:
P- Pin
S- Socket
34
■ Step 4
Special Contacts:
This step to be used
only when a special
material, finish, or
style is required.
Omit when standard
contacts are used.
Consult sales
department for
proper designation.
Order Solder Cup
Adapter for #20
AWG Stranded wire.
Use Part No. S45.
Must be ordered
separately.
S
■ Step 5
Jackscrew Locks:
JPolarized Fixed
Screw & Socket
JT- Polarized Short
Turning Screw &
Socket
JTC- Polarized Long
Turning Screw &
Socket
JTU- Polarized Short
Turning Screw &
Socket with
Round Knob
Guides:
NSS- Stainless Steel
Cylindrical
Polarized Guides
NGold Plated Brass
Polarized Guides
JTC
H13
■ Step 6
Mounting:
H8- Large Top
Opening
H13- Large Top
Opening
(High)
H9- Large Side
Opening
*When ordering
hoods separately
use Catalog
Number in Chart
■ Step 7
For Special 2-56 thds
add -859 suffix on
Series SRE part
numbers
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 57
Rack & Panel
SREC Series
Sub Miniature Rectangular, Removable Contacts
SREC 14SN
SREC 14PNH13
Tool 107-1012
The SREC series is the first family of
subminiature crimp contact rack and panel
connectors. While retaining all of the
important features of true connector miniaturization, the SREC offers .030 diameter crimp
(4 indents) type removable contacts with .094
center to center spacing. Contacts are
precision machined to assure solid pin and
socket reliability. Compact and light in weight,
the SREC Series is especially suitable for
aircraft, instrumentation, computer and
portable equipment applications.
Current Rating: 5 amps
No. of
Contacts:
7, 11, 14, 18, 20, 26, 34,
44, 50
Pin Contacts: .030 dia. 4 indent crimp.
Leaded commercial bronze,
gold plated.
Socket
Contacts:
Phosphor bronze,
gold plated.
Termination
Types:
Crimp or .025 sq. wire wrap.
Crimp contacts will accommodate #20 - #28 AWG
stranded wire.
Dielectric:
Glass-filled diallyl phthalate
per MIL-M-14, SDG-F.
Electrical Data: The dielectric withstanding
voltage is one minute
electrification at 1400 VAC.
Jackscrews: Long and short turning,
passivated stainless steel.
Anodized aluminum knurled
knobs equipped with set
screws for long turning
jackscrews. Stainless steel
knobs with groove pins for
short turning jackscrews.
SPECIFICATIONS
Guides:
Type N is standard - brass for
extra mechanical strength.
Type K - beryllium copper for
high electrical conductivity.
Type NSS - stainless steel
Hoods:
Top opening hoods are
available in all sizes.
Side opening available for
SREC 50 only.
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 58
Rack & Panel
Sub Miniature Rectangular, Removable Contacts
SREC Series
OUTLINE
Dimensions are for reference only and are subject to change. Outline drawings on request.
2-56 UNC
2A THD.
A
.58
.58
G
.13
.22
.23
.047
Typ.
C
H
B
.032 Dia.
Hole
.090
Typ.
.23
.44
.61
3-48 UNC — 2A THD.
SREC-SJ
SREC-PJT
.58
.58
A
SREC-JTCH13
.22
.22
.047
Typ.
C
B
H
.081
Typ.
2-56 UNC
2A THD.
.23
.61
Slot
.031 Wide
.13
Slot
.020 Wide
SREC-SN/K
.23
.44
SREC-PN/K
DIMENSIONS
No. of Contacts
7
14
20
26
34
50
PHYSICAL DATA
DIMENSION CHART
A
B
C
.20
.78
.56
.28
.88
.63
.28
1.06
.81
.28
1.25 1.000
.39
1.25 1.03
.39
1.63 1.40
G
1.67
1.67
1.67
1.67
1.67
2.45
H
.41
.50
.69
.88
.88
1.25
SREC 11, 18 and 44 outline drawings on request
Weight
in Ounces
(w/ o contacts)
Plug
Plug
Component Parts
Weight in Ounces
SREC 7
SREC 14
SREC 20
.03
.05
.07
.04
.06
.08
Guide Pin
Guide Socket
.02
.02
SREC 26
SREC 34
SREC 50
.08
.12
.15
.09
.15
.20
L Washer (2)
Nut (2)
.007
.01
CONTACTS
Contact
Wire Size
Type
(Stranded)
100-4024P
P (Male)
24-26-28
100-4024S
S (Female)
24-26-28
100-4020P
P (Male)
20-22
100-4020S
S (Female)
20-22
Polarizing Pin: Brass, Gold Plated, Part No. 109-8565
Part No.
Winchester/Retconn
A
—
.55
—
.48
Dimensions
B
C
.56
.028
—
.028
.50
.046
—
.046
D
.055
.055
—
—
Current
Rating
5 Amp
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 59
Rack & Panel
Sub Miniature Rectangular, Removable Contacts
SREC Series
OUTLINE
FORMED ALUMINUM HOODS
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
C
A
F
H
B
E Cable
Opening
E
D
D
A
H
.22
B
C
.22
DIMENSIONS
SRE/ SREC Large Side Opening Hoods
SRE/ SREC Large Top Opening Hoods
Code
No.*
Cable
Opening
Dimensions
A
B
C
D
E
F
Code
No.*
Fits
Connector
SRE50H9
H
SRE7H13
1.02 .75
.25
.78
.22
.16
.53
SRE14H13
1.02 .75
.34
.88
.38
.25
.53
SRE20H13
1.02 .75
.34 1.06 .38
.25
.53
SRE26H13
1.02 .75
.34 1.25 .41
.25
.53
SRE34H13
1.05 .75
.45 1.25 .73
.38
.63
SRE50H8
1.80 1.50 .45 1.63 1.19 .38
.63
SRE 7 P/ S
SREC 7 P/ S
SRE 14 P/ S
SREC 14 P/ S
SRE 20 P/ S
SREC 20 P/ S
SRE 26 P/ S
SREC 26 P/ S
SRE 34 P/ S
SREC 34 P/ S
SRE 50 P/ S
SREC 50 P/ S
*
A
B
C
D
E
H
1.63 .45 1.50 1.92 1.19 x .38 .63
Fits
Connector
SRE 50 P/ S
SREC 50 P/ S
Code numbers shown are for use with guides.
For use with jackscrews, add J or JTC to
hood part number.
ORDERING INFORMATION
Omit steps not required
SREC
34
S
JTC
H13
859
■ Step 1
■ Step 2
■ Step 3
■ Step 4
■ Step 5
■ Step 6
Insert Series
Code:
SREC
Number of
Contacts:
7, 11, 14, 18,
20, 26, 34,
44, 50
Contact
Designation:
P - Pin Molding
S - Socket
Molding
Contact Wire Size. Omit this
step if contacts are to be
ordered separately.
(See bottom chart)
Hood Type:
For 2-56 UNC
2A Threads on
H8 - Large Top
Jackscrews, add
Opening
suffix -859. Omit
(50 size only)
if not required.
H9 - Large Side
Opening
(50 size only)
H13 - Higher Top
Opening (all others)
Use only when contacts are
supplied with connector
Add:
20 - for 20-22 AWG
24 - for 24-26 AWG
28 - for 28-30 AWG
Winchester/Retconn
■ Step 7
See Hood Section For Availability
■ Step 5
Guides
KBeryllium Copper Cylindrical Guides
NBrass Cylindrical Guides (Standard)
NSS- Same style as above but Stainless Steel
Jackscrew Locks
JPolarized Fixed Jackscrew and Jacksocket
JTPolarized Short Turning Jackscrew and Jacksocket
JTC- Polarized Long Turning Jackscrew and Jacksocket
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 60
Rack & Panel
42 Series
Panel Mount Miniature
22 AWG - .030" Diameter - 5 Amps
TERMINATION TYPES
Dip Solder:
POLARIZATION
SPECIFICATIONS
CRIMP TOOLING
.125" or .156" standard
lengths with other lengths
available on special order.
Grid Spacing: .100" x .100" grid
50 or 74 contact positions on
.100" centers in 3 rows. Two
outboard rows for 25
contacts each. Center row
either for 24 additional
contacts or polarizing pins in
specified positions.
Solder Cup:
Available in 50 contact configuration only.
Choice of any combination of 24, center
positions. Specify polarizing positions
required. Positions top to bottom are: A, B, C,
D, E, F, H, J, K, L, M, N, P, R, S, T, U, V, W, X,
Y, Z, a.b.
When 74 contacts are required no polarization
other than hardware polarization is available.
Current Rating: 5.0 amps.
Pin Contacts: .030" dia. gold plated brass
conforming to specification
QQ-B-626.
Socket
Contacts:
Gold plated phosphor bronze.
Termination
Types:
Solder cup, dip solder and
crimp removable contacts.
Housing
Material:
Red diallyl phthalate for Dip
Solder and Solder Cup
Housings. Green diallyl
phthalate for Crimp Removable Housings
Dielectric:
Automatic Crimping Machine:
Cat. No. 107-0952.
Hand Crimping Tool:
Cat. No. 107-0616.
Locator:
Cat. No. 107-0617.
Contact Removal Tool:
Cat. No. 107-1012.
Contact Insertion Tool:
Cat. No. 107-1011.
Crimp
Removable:
Polarization:
Jackscrews:
Hoods:
Accommodates up to #22
AWG stranded wire.
Crimp contacts available for
#20 through #30 AWG
stranded wire. Designed for
four indent crimp. See crimp
tooling.
Minimum withstanding voltage is
one minute electrification at
1200 VAC.
Polarizing pins may be used in
any combination in center row.
Passivated stainless steel,
anodized aluminum knobs.
Anodized aluminum, top
opening only.
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 61
Rack & Panel
Panel Mount Miniature
22 AWG - .030" Diameter - 5 Amps
42 Series
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.100 Typ.
1.563
.69
.23
.06 R
.31
6-32 UNC 2-A
THD. Typ.
.100 (Typ.)
3.125
2.802
.38 x 1.41
Cable Opening
Solder Cup
.035 Dia.
Typ.
.030 Dia. Typ.
4-40 UNC 2-A
THD. Typ
.23
.38
1.469
.69
.17
Solder Cup, Clipped-in Contacts
ORDERING INFORMATION
42
36
50 / 74
P/S
■ Step 1
■ Step 2
■ Step 3
■ Step 4
■ Step 5
Series Code:
Series 42
Hardware and
Accessories:
(See bottom chart)
No. of Contacts:
50 or 74
Contact Type:
S = Socket
P = Pin
Polarization Positions:
Blank = Non-Polarized
SOLDER CUP PLUG (Clipped-in Contacts)
34 = Molding, No Hardware
35 = Molding, With Guides
36 = Molding, With Fixed Jackscrews
52 = Molding, With Short-Turning Jackscrews
53 = Molding, With Long-Turning Jackscrews
54 = Molding, With Guides and Hood
55 = Molding, With Long-Turning Jackscrews
55 = and Hood
Polarization available in 50 contact
configuration only. Choice of any
combination of 24 center positions.
Specify polarizing positions required.
Positions top to bottom are: A, B, C, D,
E, F, H, J, K, L, M, N, P, R, S, T, U, V,
W, X, Y, Z, a, b.
When 74 contacts are required no
polarization other than hardware
polarization is available.
SOLDER CUP RECEPTACLE (Clipped-in Contacts)
40 = Molding, No Hardware
41 = Molding, With Guides
42 = Molding, With Short-Turning Jackscrews,
42 = No Hood
43 = Molding, With Long-Turning Jackscrews,
42 = No Hood
44 = Molding, With Guides and Hoods
45 = Molding, With Long-Turning Jackscrews
42 = and Hood
46 = Molding, With Fixed Jackscrews
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 62
Rack & Panel
Panel Mount Miniature
22 AWG - .030" Diameter - 5 Amps
42 Series
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Dip Solder Receptacle
Shown:
74 contact right angle configuration. Center row eliminated for 50 contact connector.
.550
.450
.375
.350
2.802
.234
3.125
.688
Typ.
4-40 UNC 2-A THD. Typ
.205
.156
.100
Typ.
.030
.313
Dip Solder, Molded-in Contacts
ORDERING INFORMATION
42
■ Step 1
■ Step 2
Series Code:
Series 42
Hardware and
Accessories:
DIP SOLDER
(Molded-in Contacts)
30 = No Hardware
31 = Guide Pin
and Socket
32 = Fixed Jackscrew
and Jacksocket
■ Step 3
No. of Contacts:
50 or 74
- 30
74
■ Step 4
Contact Type:
P = Pin
P
4
■ Step 5
Polarization Positions:
Blank = Non-Polarized
■ Step 6
Termination Type:
4 = Dip Solder
Contacts...125"
Polarization available in 50
5 = Dip Solder
contact configuration only. Choice
Contacts...156"
of any combination of 24 center
852 = Right Angle
positions. Specify polarizing
Dip Solder
positions required. Positions top
Contacts .205"
to bottom are: A, B, C, D, E, F, H,
J, K, L, M, N, P, R, S, T, U, V, W,
X, Y, Z, a, b.
When 74 contacts are required no
polarization other than hardware
polarization is available.
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 63
Rack & Panel
Panel Mount Miniature
22 AWG - .030" Diameter - 5 amps
42 Series
OUTLINE
.69
.32
.37
.18
#6-32 UNC-2A
.200
.050
2.50
2.800
3.13
.100 Typ.
#6-32 UNC-2B
.100
.200
.15
1.54
ORDERING INFORMATION
42
■ Step 1
Series Code:
Series 42
■ Step 2
1 = Crimp Connector
Molding
1
36
50
■ Step 3
■ Step 4
■ Step 5
Hardware and
Accessories:
(See bottom chart)
No. of
Contacts:
50 or 74
Contact Type:
S = Socket
P = Pin
Crimp removable contacts
are ordered separately.
Crimp Removable Pin Contacts
34 = Molding, No Hardware
35 = Molding, With Guides
36 = Molding, With Fixed Jackscrews
52 = Molding, With Short-Turning Jackscrews
53 = Molding, With Long-Turning Jackscrews
54 = Molding, With Guides and Hood
55 = Molding, With Long-Turning Jackscrews
55 = and Hood
Crimp Removable Socket Contacts
40 = Molding, No Hardware
41 = Molding, With Guides
42 = Molding, With Short-Turning Jackscrews,
42 = No Hood
43 = Molding, With Long-Turning Jackscrews,
42 = No Hood
44 = Molding, With Guides and Hoods
45 = Molding, With Long-Turning Jackscrews
42 = and Hood
46 = Molding, With Fixed Jackscrews
Pin Contacts:
100-4020P
100-4024P
100-4028P
Socket Contacts:
100-4020S
100-4024S
100-4028S
Socket Contacts
(Closed Entry):
100-54020S
100-54024S
100-54028S
P
■ Step 6
Polarization Positions:
Blank = Non-Polarized
Polarization available in 50
contact configuration only. Choice
of any combination of 24 center
positions. Specify polarizing
positions required. Positions top
to bottom are: A, B, C, D, E, F, H,
J, K, L, M, N, P, R, S, T, U, V, W,
X, Y, Z, a, b.
When 74 contacts are required no
polarization other than hardware
polarization is available.
See 100 Series Contact
Section of Rack & Panel
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 64
Rack & Panel
SRM Series
Sub Miniature Rectangular #20 Contacts / .040" Dia. / 7.5 Amps
SRM Series connectors are particularly suitable
where current rating and voltage drop require-
ments dictate a larger wire size than can be
used with other subminiature connectors.
XSRM14PNSS2500
XSRM14PNSS1000
SRM14SNSS0000
SRM26SCO300
XSRM26SM2000
SRM26PF0000
SPECIFICATIONS
Current Rating: 7.5 Amps
No. of
Contacts:
5, 7, 11, 14, 20, 26, 34, 50,
75, 104
Pin Contacts: .040 dia. brass, gold plated.
Socket
Contacts:
Phosphor, bronze,
gold plated.
Termination
Types:
.048 dia. solder cups will
accept up to #20 AWG
stranded wire. Dip Solder
Contacts, .030 dia. Check
Sales Dept. for available
lengths.
Electrical Data: Minimum dielectric withstanding voltage is one minute at
1500 VAC when tested in
accordance with MIL-C-28748.
Dielectric:
Guides:
Jackscrews:
Hoods:
Shells:
Glass-filled diallyl phthalate grey- per MIL-M-14, SDG-F.
NSS Type, stainless steel; or
N Type, brass.
Stainless steel with knurled
and slotted aluminum knobs.
Anodized aluminum. May be
applied to either plug or
receptacle. Both top and side
openings are available.
Polarized shells are available.
SRM connector assembled
with a shell changes part
number from SRM _ _ _ _ _ to
XSRM _ _ _ _ _ .
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 65
Rack & Panel
Sub Miniature Rectangular #20 Contacts / .040" Dia. / 7.5 Amps
SRM Series
CONTACT ARRANGEMENTS
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
2-56 UNC - 2A THD.
.55
.23
.06R
.48
.23
.22
.22
.040
DIA.
.133
.531
.780
.048 Dia.
Solder
Cup
.125
.108 Typ.
SLOT
.025
WIDE
.20
.48
SRM5P-NSS
.34
.06R
.063
Typ.
.063
Typ.
.09R
.063
Typ.
.625
.870
.625
.870
.123
.123
.20
SRM7S-NSS
.108 Typ.
.108 Typ.
.55
SRM7P-NSS
SRM11P-NSS
.108 Typ.
.50
.108 Typ.
.34
.09R
.063
Typ.
.34
.063
Typ.
.50
.34
.09R
.09R .063
Typ.
2.06
1.812
.09R
.063
Typ.
1.250
1.000
1.25
.750
1.000
1.312
1.56
1.50
.125
.125
.125
.125
.125
.172
.172
.108 Typ.
.108 Typ.
.108 Typ.
SRM14P-NSS SRM20P-NSS
Mounting
.343
holes for
No. 2 machine
screws (Typ.)
.343
SRM26S-NSS SRM34P-NSS
SRM50P-NSS
.67
.61
.36
.108 Typ.
2-56 UNC.2A THD.
.94
.61
.36
.72
2-56 UNC. 2A THD.
.67
.36
.562
.218
.36
.063
Typ.
.09R
.063
Typ.
.09R
.040
Dia.
.040
DIA.
.09R
.063
Typ.
.048
Dia.
Solder
Cup
.048
Dia.
Solder
Cup
2.38
.133
2.062
.133
2.06
1.812
.159
.125
.19
.61
SLOT
.025
WIDE
SRM75S-NSS
.19
.172
Mounting holes .108 Typ.
for No. 2 machine
screws (Typ.)
.67
SRM75P-NSS
.19
.61
SLOT
.025
WIDE
.19
.67
.312
.625
6-32 UNC.
2A THD.
*Center guides are .038 x .062
SRM104S-NSS
SRM104P-NSS
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 66
Rack & Panel
SRM Series
Sub Miniature Rectangular #20 Contacts / .040" Dia. / 7.5 Amps
OUTLINE
JACKSCREWS & JACKSOCKETS
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Mating thread size 2-56
UNC except size 104
which is 6-32 UNC.
.11
Jacksocket
F
AND
Mating connector half with turnable
Jackscrews-with-Knobs Code
designation M
Jackscrew locking device assures positive
coupling of engaged connectors to prevent
accidental disconnecting from vibration or
physical shock. It also aids easy connection
and separation of connector plug and
receptacle. Mounted connector-half houses
one non-turnable fixed jackscrew and
jacksocket to insure connector polarization.
Mating-half houses one of the two types of
turning jackscrew and jacksocket (M or C)
Turnable jackscrew-jacksocket combination
(M or C) assembles on either Plug or
Hood
Set Screw
B
E
Connector with fixed Jackscrews Code designation F
A
Solder Cups
Solder Cups
.13
.58
Jacksocket
OR
Mating connector half with Hood and
turnable Long Jackscrews-with-Knobs
Code designation C-0300, C-0400
Receptacle, the mating connector-half (either
Receptacle or Plug) must then contain fixed
jackscrew-jacksocket combination (F).
Both short and long turning jackscrews
(M and C) have knurled and slotted knobs for
locking by hand or screwdriver. Knob is
assembled on shaft with a socket setscrew.
Safety wiring of engaged halves is achieved
by using the through-holes.
Drawings show extension of standard knobs
beyond hood.
DIMENSIONS
Short
Fixed
Long Turning
Code “C”
Turning
Jacks
Standard
Connec- 0300 0300X Code “M” Code “F”
tor Size
A
B
E
F
SRM 5
SRM 7
SRM 11
SRM 14
SRM 20
SRM 26
SRM 34
SRM 50
SRM 75
SRM 104
–
–
–
–
–
.56
.56
.56
.56
.56
–
1.28
1.84
1.84
2.09
2.09
2.09
2.09
2.23
2.80
.92
.92
.92
.92
.92
.92
.92
.92
1.06
1.06
.53
.53
.53
.53
.53
.53
.53
.53
.67
.67
CODES
Note: Jackscrews and jacksockets are
stainless steel with passivating dip.
Knob is anodized aluminum.
TYPE
Jackscrew
Jacksocket
Code Letter
Fixed
F
Jackscrew
Short
Jacksocket Turnable
M
Jackscrew
Long
Jacksocket Turnable
C
Knob
—
Standard
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 67
Rack & Panel
SRM Series
Sub Miniature Rectangular #20 Contacts / .040" Dia. / 7.5 Amps
HOODS - FORMED ALUMINUM
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Top Cable Opening Hoods
Side Cable Opening Hoods
D
F
G
E
F & G (Cable Opening)
F&G
(Cable Opening)
(0300 Only)
(0400 Only)
G
B
F
C
D
B
A
A
E
2-26 UNC-2A THD. (0500 Only)
DIMENSIONS
Top Cable Opening Hoods
2-56 UNC-2A THD. (0600 Only)
C
0300X Cable Clamp
0400X Cable Clamp
0300X Hood is identical to 0300 Hood except
for cable clamp style and cable opening in the
hood.
0400X Hood is identical to 0400 Hood except
for cable clamp style and cable opening in the
hood.
Code
No.
A*
SRM 7-0300X
SRM 7-0500
SRM 7-0500X
SRM 11-0300X
SRM 11-0500
SRM 11-0500X
SRM 14-0300X
SRM 14-0500
SRM 14-0500X
SRM 20-0300X
SRM 20-0500
SRM 20-0500X
SRM 26-0300
SRM 26-0300X
SRM 26-0500
SRM 26-0500X
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
Dimensions
B C
D E
.38
.38
.38
.94
.94
.94
.94
.94
.94
1.19
1.19
1.19
1.19
1.19
1.19
1.19
.67
.69
.67
1.23
1.25
1.23
1.23
1.25
1.23
1.67
1.63
1.67
1.63
1.63
1.63
1.63
.88
.88
.88
.88
.88
.88
1
1
1
1.25
1.25
1.25
1.5
1.5
1.5
1.5
.30
.30
.30
.41
.41
.41
.41
.41
.41
.41
.41
.41
.41
.41
.41
.41
Cable
Opening
F G
.36
.30
.36
.47
.44
.47
.5
.44
.5
.72
.34
.72
.56
.91
.56
.91
.23
.23
.23
.34
.34
.34
.34
.34
.34
.34
.72
.34
.34
.34
.34
.34
Code
No.
A*
SRM 34-0300
SRM 34-0300X
SRM 34-0500
SRM 34-0500X
SRM 50-0300
SRM 50-0300X
SRM 50-0500
SRM 50-0500X
SRM 75-0300
SRM 75-0300X
SRM 75-0500
SRM 75-0500X
SRM 104-0300
SRM 104-0300X**
SRM 104-0500
SRM 104-0500X**
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
Dimensions
B C
D E
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.75
1.75
1.75
1.75
1.63
1.67
1.63
1.67
1.63
1.67
1.63
1.67
1.63
1.72
1.63
1.72
2.28
2.52
2.28
2.52
1.56
1.56
1.56
1.56
2.06
2.06
2.06
2.06
2.06
2.06
2.06
2.06
2.38
2.38
2.38
2.38
Cable
Opening
F G
.56 .63 .5
.56 .81 .5
.56 .63 .5
.56 .81 .5
.56 .66 .5
.56 .88 .5
.56 .66 .5
.56 .88 .5
.78 .63 Dia.
.78 .91 .72
.78 .63 Dia.
.78 .91 .72
1 1.06 .94
1
.86 1.36
1 1.06 .94
1
.86 1.36
Hoods may be ordered separately (see code numbers in above tables) or assembled on connectors. If desired
assembled to connectors, see Code Numbering System for complete catalog number.
Prefix hood code numbers with “X” for use with shells. Example: XSRM34- 0300
Side Cable Opening Hoods
Code
No.
A*
SRM 11-0400
SRM 11-0400X
SRM 11-0600
SRM 11-0600X
SRM 14-0400
SRM 14-0400X
SRM 14-0600
SRM 14-0600X
SRM 20-0400
SRM 20-0400X* *
SRM 20-0600
SRM 20-0600X* *
SRM 26-0400
SRM 26-0400X
SRM 26-0600
SRM 26-0600X
Winchester/Retconn
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
Dimensions
B C
D E
.94
.94
.94
.94
.94
.94
.94
.94
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.17
1.19
1.17
1.31
1.30
1.31
1.30
1.69
1.73
1.69
1.73
1.94
1.94
1.94
1.94
.88
.88
.88
.88
1
1
1
1
1.25
1.25
1.25
1.25
1.5
1.5
1.5
1.5
.41
.41
.41
.41
.41
.41
.41
.41
.41
.41
.41
.41
.41
.41
.41
.41
Cable
Opening
F G
.44
.34
.44
.34
.44
.5
.44
.5
.56
.72
.56
.72
.56
.91
.56
.91
.34
.47
.34
.47
.34
.34
.34
.34
.34
.34
.34
.34
.34
.34
.34
.34
Code
No.
A*
SRM 34-0400
SRM 34-0400X
SRM 34-0600
SRM 34-0600X
SRM 50-0400
SRM 50-0400X
SRM 50-0600
SRM 50-0600X
SRM 75-0400
SRM 75-0400X
SRM 75-0600
SRM 75-0600X
SRM 104-0400
SRM 104-0400X
SRM 104-0600
SRM 104-0600X
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
Dimensions
B C
D E
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.19
1.75
1.75
1.75
1.75
2
2.03
2
2.03
2.5
2.53
2.5
2.53
2.5
2.58
2.5
2.58
2.91
2.91
2.91
2.91
1.56
1.56
1.56
1.56
2.06
2.06
2.06
2.06
2.06
2.06
2.06
2.06
2.38
2.38
2.38
2.38
.56
.56
.56
.56
.56
.56
.56
.56
.78
.78
.78
.78
1
1
1
1
Cable
Opening
F G
.63 .5
.81 .5
.63 .5
.81 .5
.66 .5
.88 .5
.66 .5
.88 .5
.63 Dia.
.91 .72
.63 Dia.
.91 .72
1.06 .94
1.44 .94
1.06 .94
1.44 .94
* * Note: This dimension does not apply when shells are used. Tab is removed.
* * Request availability information.
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 68
Rack & Panel
Sub Miniature Rectangular #20 Contacts / .040" Dia. / 7.5 Amps
SRM Series
PLUG SHELLS
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
For Use With XSRM Connectors
B
C
.093 Dia.
4 Holes
D E
.06R
.14R
.05R
2 Slots
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
D E
A
B
C
DA
E
F
G
.125 Typ
For XSMR 7 to 26
RECEPTACLE SHELLS
Polarizing Slot
D E
.06R
.06R
.05R
(.07R for 104)
2 Slots
For All XSRM
Config.
.05R
2 Slots
For XSMR 7 to 26
MATERIAL
B
C
.562
B
C
.97 .33
.97 .44
1.11 .44
1.34 .44
1.61 .44
1.66 .61
2.16 .83
2.16 .81
2.48 1.05
.093 Dia.
4 Holes
A
B
C
D
A
E
F
G
D E
D E
Polarizing Slot
.06R
.06R
.125 Typ
.05R
(.07R for 104)
2 Slots
For All XSRM
Config.
G
.203
.13R
For XSRM 34, 50,
and 104
G
.05R
(Typ.)
For XSRM 75
Shells also provide a means by which
connector polarization is accomplished receptacle shell is slotted for engaging a
polarizing pin on plug shell. Non-polarized
shells have the slot and pin omitted.
The shell part numbers given in table show an
asterisk (*) where the code letter for the
desired polarizing position belongs - example:
XSRM14-2*000 becomes XSRM14-2B000
when polarization in position “B” is desired.
Specify the same position on the mating
shell. For non-polarized shells, merely omit
this position, e.g. XSRM14-2000.
Shell Size
Available Polarization
Positions
Shell Size
Available Polarization
Positions
7
11
14
20
26
A,B,C,D
A,B,C,D
A,B,C,D,E
A,B,C,D,E,F,G
A,B,C,D,E,F,G
34
50
75
104
A,B,C,D,E,F,G
A,B,C,D,E,F,G
A,B,C,D,E,F,G
A,B,C,D,E,F,G
Receptacle Shells ( .031" thick)
Plug Shells ( .031" thick)
XSRM 7-1*000
XSRM 11-1*000
XSRM 14-1*000
XSRM 20-1*000
XSRM 26-1*000
XSRM 34-1*000
XSRM 50-1*000
XSRM 75-1*000
XSRM 104-1*000
.093 Dia.
4 Holes
Shells are .031 thick aluminum, anodized for
protection against corrosion. Either style plug or receptacle - may be used to house a
female insert, thus allowing “live” socket
contacts to be cable or panel mounted.
DIMENSIONS
B
For XSRM 75
F
.06R
A
G
H
D E
.14R
.14R
.203
For Use With XSRM Connectors
B
C
Shell Part No.
(if ordered
separately)
.093 Dia.
4 Holes
G
For XSRM 34, 50,
and 104
.14R
POLARIZATION
.14R
F
H
B
C
B
C
.562
.05R
(Typ.)
Dimensions
C
D
E
.23
.34
.34
.34
.34
.5
.5
.72
.94
.625
.625
.750
1.00
1.250
1.312
1.812
1.812
2.062
Winchester Electronics
.53
.53
.67
.94
1.16
1.16
1.66
1.66
1.81
F
G
H
.44
.44
.44
.44
.44
.44
.44
.58
.58
–
–
–
–
–
.172
.172
.281
.312
.31
.31
.31
.31
.31
.31
.31
.45
.45
Shell Part No.
(if ordered
separately)
XSRM 7-2*000
XSRM 11-2*000
XSRM 14-2*000
XSRM 20-2*000
XSRM 26-2*000
XSRM 34-2*000
XSRM 50-2*000
XSRM 75-2*000
XSRM 104-2*000
A
B
1
.36
1
.47
1.13 .47
1.38 .47
1.63 .47
1.69 .63
2.19 .63
2.19 .84
2.5 1.06
Dimensions
C
D
E
.23
.34
.34
.34
.34
.5
.5
.72
.94
.625
.625
.750
1.00
1.250
1.312
1.812
1.812
2.062
.53
.53
.67
.94
1.16
1.16
1.66
1.66
1.81
F
G
H
.44
.44
.44
.44
.44
.44
.44
.58
.58
–
–
–
–
–
.172
.172
.281
.312
.19
.19
.19
.19
.19
.19
.19
.33
.33
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 69
Rack & Panel
Sub Miniature Rectangular #20 Contacts / .040" Dia. / 7.5 Amps
SRM Series
ORDERING INFORMATION
Omit steps not required
SRM
26
P
■ Step 1
■ Step 2
■ Step 3
■ Step 4
Insert Series
Code:
SRM - When
protective
shells are not
required.
XSRM - When
protective
shells are
required.
Number of
Contacts:
5, 7, 11,
14, 20, 26,
34, 50, 75
and 104.
Contact
Designation:
P - Pin
S - Socket
Guides:
Type of
Contact:
(See bottom
Chart)
Blank =
Standard
Solder Cup
This step to be
used only when a
special material,
finish, or style is
required. Omit
when standard
contacts are used.
Consult Sales
Department for
proper designation
of Dip Solder
Terminations
■ Step 5
C
0
3
0
■ Step 6
■ Step 7
■ Step 8
Shell Type:
0 - Shell not
required
SRM
Series
1 - Plug shell
XSRM
Series
2 - Receptacle
shell
XSRM
Series
Polarization
Position:
A, B, C, D, E, F
or G. Omit
letter when
polarization of
shell is not
required.
Hoods:
“0” fill to
“0” fill to
complete
0 - When no complete
part number part number
hood
required.
3 - Standard size
top cable
opening. If
extra large
cable
opening is
desired, add
“X” to end of
catalog
number.
4 - Standard size
side cable
opening. If
extra large
cable
opening is
desired, add
“X” to end of
catalog
number.
5 - Top opening
hood for use
with guides.
6 - Side opening
hood for use
with guides.
■ Step 5
Guides
NSS - Standard stainless steel cylindrical guides.
NBrass cylindrical guides. Plated, gold over copper.
■ Step 9
0
■ Step 10
Jackscrews and Jacksockets
CPolarized long turning jackscrew and jacksocket for
use with hoods.
FPolarized fixed jackscrew and jacksocket.
MPolarized short turning jackscrew and jacksocket.
JNon-polarized short turning jackscrews.
LNon-polarized long turning jackscrews.
RNon-polarized fixed jacksockets.
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 70
Rack & Panel
High Voltage, Single Contact / #20 Contacts / .040" Dia. / 7.5 Amps
PM1 Series
N
Nylon Nut
PM1SLR
Plug with lock ring
PM1PLS
Receptacle with lock spring
H10
Hood
This connector was developed for applications requiring moderately high voltage ratings, this
single contact connector is particularly well adapted to Photo-Flash, Aircraft, Instumentation
and Communications Equipment.
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.66
.75
.75
.47
.56
.25
.09
.09
.25
.03
.25
.13
.125
Cable
Opening
30O
.68
Hex.
.386
Panel Drilling
.16
.66
.048 Dia.
Solder Cup
3/8 - 24 UNF - 2THD.
PM1PLS
Receptacle with lock spring
PM1SLRN
Plug with lock ring
H10
Hood
SPECIFICATIONS
ORDERING INFORMATION
Current Rating: 7.5 amps
No. of
Contacts:
1
Pin Contacts: .040 dia. brass, gold plated
Socket
Contacts:
Phosphor bronze, gold plated
Terminations: .048 solder cup will accept
up to #20 AWG stranded
wire.
Electrical Data: Dielectric withstanding
voltage is one minute
electrification at 5650 VAC.
Dielectric:
Molded Diallyl phthalate per
MIL-M-14, type SDG-F.
Color Gray.
Polarization: Permits one engaging
position only and prevents
rotation of the plug and
PM1PLRPM1SLSPM1PLSPM1SLRPM1PPM1S-
Connector,
Connector,
Connector,
Connector,
Connector,
Connector,
Mounting:
Lock Ring (and
lock spring): Applied to plug or receptacle.
Prevents connector rotation
on panel and when engaged
with lock spring, prevents
accidental disconnection due
to vibration, etc.
Hood:
Diallyl Phthalate cable hood
Weight in
Ounces:
Receptacle .05, Plug .05,
Washer .005, Hood .07,
Lock Ring .017,
Lock Spring .019, Nut .015
plug with lock ring
receptacle with lock spring
plug with lock spring
receptacle with lock ring
plug without vibration lock
receptacle without vibration lock
*Add H10- to above numbers when ordering hoods
*Add H10C- to above numbers for hood with cable clamp
Winchester/Retconn
Add N-
receptacle with respect to
each other.
Cable or panel mounted. Use
nylon nut applied to either plug
or receptacle.
to above numbers when ordering nylon nut
* When ordering hoods
separately specify
P/N H10T34 or H10CT34
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 71
Rack & Panel
High Voltage Miniature / # 20 Contacts / .040" Dia. / 7.5 Amps
PM6 Series
N
Nylon Nut
PM6PLS
Plug with lock spring
PM6SLR
Receptacle with lock ring
PM6H
Hood
weight is particularly well adapted to PhotoFlash, Aircraft, Instumentation and Communications Equipment.
This connector was developed for applications requiring moderately high voltage
ratings, this connector of minimum bulk and
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.13
.25
.0995 Dia.
.13
.53
.25
.015
.025
1.125
.53
.36
1.266
.53
30O
.94
Hex
.78 Dia.
1.219
1.031
.048 Dia.
Solder Cup
.875
Dia.
.38 Dia.
Cable Opening
.16
Molding
Nut
7/8 20 UNEF 2A
.22
.22
Panel Drilling
PM6SLRN
Receptacle
PM6PLS
Plug
PM6H
Hood
SPECIFICATIONS
Current Rating: 7.5 amps
No. of
Contacts:
6
Pin Contacts: .040 dia. brass, gold plated
Socket
Contacts:
Spring temper phosphor
bronze, gold plated
Terminations: .048 dia. solder cup accepts
up to #20 AWG stranded
wire.
Electrical Data: Dielectric withstanding
voltage is one minute
electrification at 3560 VAC.
Dielectric:
Molded Diallyl phthalate per
MIL-M-14, type SDG-F.
Color Gray.
Polarization:
Mounting:
Body design makes it
impossible to make connection
except in proper position.
Cable or panel mounted. Use
nylon nut applied to either plug
or receptacle.
Lock Ring (and
lock spring): Prohibits connector rotation
on panel mounting and when
engaged with lock spring,
prevents accidental disconnection due to vibration, etc.
Hood:
Molded diallyl phthalate cable
hood may be applied to either
plug or receptacle.
ORDERING INFORMATION
Winchester/Retconn
PM6PLSPM6SLRPM6PLRPM6SLSPM6PPM6S-
Connector,
Connector,
Connector,
Connector,
Connector,
Connector,
plug with lock spring
receptacle with lock ring
plug with lock ring
receptacle with lock spring
plug without vibration lock
receptacle without vibration lock
Add HAdd N-
to above numbers when ordering hoods
to above numbers when ordering nylon nut
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 72
Rack & Panel
SM Series
Sub Miniature / # 20 - #24 Contacts / 3 And 7.5 Amps
N
Nylon Nut
SMH
Hood
SM2P
Plug
SM2
Receptacle
Extreme compactness and lightweight of
these subminiature connectors make them
ideal for limited space application in Aircraft.
Portable Equipment and Instrumentation.
SPECIFICATIONS
Current Rating: SM1 - 7.5 amps;
SM2, SM3 - 3 amps
No. of
Contacts:
1, 2, 3
Pin Contacts: SM1 - .040 dia.
brass, gold plated
SM2, SM3 - .025 dia.
brass, gold plated
Socket
Contacts:
Phosphor bronze, gold plated
Terminations: SM1 - .048 dia. solder cup
will accept up to #20 AWG
stranded wire.
SM2, SM3 - .037 dia. solder
cup will accept up to #24
AWG stranded wire.
Electrical Data: Dielectric withstanding voltage
is one minute electrification at
1200 VAC.
Dielectric:
Diallyl Phthalate per MIL-M-14,
type SDG-F. Color Gray.
Polarization: Body design allows engagement in only one position.
Mounting:
Either plug or receptacle may
be mounted on chassis or
bulkhead with 1/4 - 28 cadmium
plated brass nut. Add “N” to
code number to order.
Hood:
Cable hood may be applied to
both plug and receptacle. Add
“H” to code number. When
ordering a hood separately,
order P/N SMH.
PHYSICAL AND
ELECTRICAL DATA
Current Rating
SM1 - 7.5 Amp
Weight in Ounces
P.
R.
.02
.02
* Wire Range
SM1 - #20
SM2 - 3 Amp
.02
.02
SM2 - # 24
SM3 - 3 Amp
.02
.02
SM3 - # 24
* Stranded
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762
Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 73
Rack & Panel
Sub Miniature / # 20 - #24 Contacts / 3 And 7.5 Amps
SM Series
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.55
.55
.50
.255
.09
.25
.31 Hex.
.09
.28
.100
.25
.31
.13
.048 Dia.
Solder Cup
Panel
Opening
.040 Dia.
1/4 - 28 UNF-2 THD.
Receptacle
SM1SN
Plug
SM1P
.31
.55
Hood
SMH
.50
.55
.06
.09
.22
.17
.19
.255
.100
.19
.31 .23
.23
.13
1/4 - 28 UNF-2 THD.
1/4 - 28 UNF-2 THD.
Receptacle
SM2SN
Plug
SM2P
.50
.55
.55
.31
Hood
SMH
.06
.19
.09
.22
.17
.23
.19
.23
.13
1/4 - 28 UNF - 2 THD.
Receptacle
SM3SN
Hood
SMH
Plug
SM3P
ORDERING INFORMATION
SM
■ Step 1
■ Step 3
Series Code:
Series SM
No. of Contacts:
1, 2, 3
3
S
■ Step 4
Contact Type:
P = Pin
S = Socket
H
■ Step 4
Type:
N = Nut
H = Hood
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 74
Rack & Panel
High Voltage Miniature / # 20 Contacts / .040" Dia. / 7.5 Amps
M Series
M4PLSH10
Plug with lock spring and hood
N
Nylon Nut
M12SLS12
Receptacle with lock spring
M4SLRGN
Receptacle with lock ring,
ground lug and nut
M10SLRN
Receptacle with lock ring
and nut
M12P
Plug
M10PLSH19
Plug with lock spring and
hood
M12H
Hood with lock shell
The extreme compactness and lightweight of
M connectors make them ideal for such
applications as strain gauges, telemetry and
pressure pick-up installations in aircraft,
portable equipment and instrumentation.
SPECIFICATIONS
Current Rating: 7.5 amps
No. of
Contacts:
4, 5, 7, 9, 10, 12
Pin Contacts: .040 dia. brass, gold plated
Socket
Contacts:
Spring temper phosphor
bronze, gold plated
Terminations: .048 dia. solder cup accepts
up to #20 AWG stranded wire.
M12 - .043 dia. solder cup
accepts up to #20 AWG
stranded wire.
Electrical Data: The dielectric withstanding
voltage is one minute
electrification at 1500 VAC.
(2250 VAC for M12).
Dielectric:
Brown mineral filled diallyl
phthalate. Also available in
gray glass filled diallyl
phthalate, per MIL-M-14,
SDG-F.
Polarization:
Mounting:
Body design permits engagement in proper position only.
For 1/16" panel mounting of
either plug or receptacle use
cadmium plated brass nut for
M4-10, nylon nut for M12.
Add “N” to code number.
Lock Ring (and
lock spring): May be applied to plug or
receptacle to stop connector
rotation on panel. When
engaged with lock spring,
prevents accidental disconnection due to vibration, etc.
Ground Lug: Can be used to ground any of
the 4 contacts on M4 connector. Add “G” to code number.
Hood:
Anodized aluminum or brown
mineral filled diallyl phthalate
hoods may be applied to plug
or receptacle of M4-M10. With
or without cable clamps to
provide additional strain relief
for the cable.
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 75
Rack & Panel
High Voltage Miniature / # 20 Contacts / .040" Dia. / 7.5 Amps
M Series
OUTLINE
.91
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
1.125
.56
.38
.0995 Dia.
Nut
1.250
.890 Dia.
Panel Opeming
.38
7/8 - 20 THD
.16 .16
M21S
.048 Dia.
Solder Cup
.34
.47
.13
.250
30O
.53
.34
.09
.53
.63
.09
.47
.25
Lock Ring
(LR)
.385
.69
.25
.50
.125
3/8 - 24 UNF THD
Panel Drilling
Ground Lug (G)
3/8 - 24 UNF THD
Lock Spring (LS)
Nut & Lockwasher (N)
Receptacle
M4S-LRGN
.048 Dia.
Solder Cup
.72
.25
Plug
M4P-LS
(See
Views
Below)
.44
.09
.09
.44
LR
LS
LN
LN
LN
—
—
—
—
—
Accessory Code
Lock Ring
Lock Spring
Nut & Lockwasher
to be used as suffixes
when required.
.77
.66
.56 A/F
Hex Nut
1/2 - 20 UNF THD.
Lockwasher
1/2 - 20 UNF THD.
Receptacle
M*S-LRN
Plug
M*P-LS
.515 Dia.
.34
30O
.099 Dia.
Panel Drilling
(Viewed from Front of Panel)
Contact
Arrangement
M5S
Contact
Arrangement
M7S
Contact
Arrangement
M9S
Contact
Arrangement
M10S
Contact locations are shown from terminal sides
PHYSICAL AND
ELECTRICAL DATA
NOTE: Contact arrangement of M * P are reversed
* Insert number, indicating number of contacts (5, 7, 9, 10)
Number
Catalog
of
Number Contacts
Winchester/Retconn
Lock
Ring
Lock
Washer
Solder
Cup
Hole
Dia./in.
Current
Rating
Weight In Ounces
Plug
Rec.
Nut
Lock
Spring
M4P
M4S
4
.08
.06
.08
.02
.02
.01
.048
7.5 amps
M5P
M5S
5
.10
.08
.06
.02
.03
.01
.048
7.5 amps
M7P
M7S
7
.12
.10
.06
.02
.03
.01
.048
7.5 amps
M9P
M9S
9
.13
.10
.06
.02
.03
.01
.048
7.5 amps
M10P
M10S
10
.13
.10
.06
.02
.03
.01
.048
7.5 amps
M12P
M12S
12
.3
.4
.05
.02
.03
.01
.043
7.5 amps
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 76
Rack & Panel
High Voltage Miniature / # 20 Contacts / .040" Dia. / 7.5 Amps
M Series
MOLDED DIALLYL PHTHALATE
AND ALUMINUM HOODS
Molded diallyl phthalate cable hoods protect
soldered wires and facilitate disengagement
of connectors. Cable clamps provide
additional strain relief and support. They are
supplied on hoods with “C” in the code
number. Clamps are cadmium plated with
olive drab iridite finish. Anodized aluminum
hoods are precision machined from bar stock
to give greater strength than die cast units.
Cable clamps are machined as an integral
part of the connector. The set screw prevents
accidental disassembly from vibration, etc. A
polyethylene sleeve liner provides added
insulation in the terminal area.
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
standard hoods
C
1.125
MAX.
.38
B
1.188
D
F
1.375
.438 WIDE x .313 HIGH
CABLE OPENING
A
SLOT 0.38 WIDE
E
M12H
H9, H10, H19
modified hoods
hood with cable clamps
B
C
B
C
D
A
D
CABLE
OPENING
F
F
A
CABLE OPENING
E
H9S, H19S
H9C, H10C, H19C, H19CS
special hood with cable clamps
special hoods
Used on Connectors M5, M7, M9, M10
B
C
D
.14
F
A
CABLE
OPENING
HG9, HG18
CABLE
OPENING
1
/2 -20 NF2
.66
.83
HG9C
aluminum hoods
1.438 WHEN CONNECTED
1.00
.19
.56 DIA
4-40 SET SCREW
1.188 WHEN
CONNECTED
.94
.25 CABLE
OPENING
H14
For M4
.22
CABLE
OPENING
.66
H16
For M5, M7,
M9, M10
SET SCREW (4-40)
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 77
Rack & Panel
M Series
High Voltage Miniature / # 20 Contacts / .040" Dia. / 7.5 Amps
PHYSICAL DATA
Hood
Code
Number
H9
Used on
of
Connectors
M5, 7, 9, 10
DIMENSIONS
F-Thds
Weight In
Ounces
A
B
C
D
E
.14
.66
.66
.27
.88
1/ 2
- 20
.10
H10
M4
.16
.56
.69
.25
.75
3/ 8
- 24
.05
H19
M5, 7, 9, 10
.30
.66
.66
.42
.88
1/ 2
- 20
.08
H9C
M5, 7, 9, 10
.16
.66
.78
.55
.97
1/ 2
- 20
.11
H10C
M4
.19
.56
.69
.44
.88
3/ 8
- 24
.09
H19C
M5, 7, 9, 10
.30
.66
.78
.55
.97
1/ 2
- 20
.12
H19CS
M5, 7, 9, 10
.30
.66
.66
.55
.86
1/ 2
- 20
.11
H9S
M5, 7, 9, 10
.14
.66
.66
.55
1/ 2
- 20
.07
H19S
M5, 7, 9, 10
.30
.66
.66
.55
1/ 2
- 20
.06
- 20
.10
- 20
.11
HG9
M5, 7, 9, 10
.22
.66
.66
.59
1/ 2
HG18
M5, 7, 9, 10
.28
.66
.66
.59
1/ 2
HG9C
M5, 7, 9, 10
See Drawing
.14
H14
M4
See Drawing
.25
H16
M5, 7, 9, 10
See Drawing
.25
H12H
M12
See Drawing
1.10
ORDERING INFORMATION
Omit steps not required
M
P/S
■ Step 1
■ Step 2
■ Step 3
■ Step 4
■ Step 5
■ Step 6
Series
Code:
M series
No. of
Contacts:
4, 5, 7, 9,
10, 12
Contact
Type:
P = Pin
S = Socket
LS = lock spring
LR = lock ring
LS6 = M12 lock spring
LR6 = M12 lock ring
LS12 = lock spring for
M12H hood
N = Nut
G = Ground lug
(M4 only)
■ Step 7
Hoods:
See hood code
number above.
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762
RP / 78
Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
Rack & Panel
Miniature Side Mount / # 20 Contacts / .040" Dia. / 7.5 Amps
JF Series
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Side Mounting, 4 Position Rectangular
2 and 4 Position In-Line
JF Series, PIN and Socket, 2 Position In-Line Connectors
Dimensions shown are typical for all standard 2 position in-line connectors.
.06
1.6
.53
13.5
.76
19.2
.04
1.0
.44
11.1
.34
8.7
.17
4.4
.13
3.2
.08
2.0
.22
5.5
.09
Thru C'Sink
2.3
.28
7.1
.05
Solder Cup
1.3
.17
x 82o
4.3
JF1S1PA
JF1P1SA
JF Series, PIN and Socket, 4 Position In-Line Connectors
Dimensions shown are typical for all standard 4 position in-line connectors.
.11
2.8
.55
13.9
.36
9.1
.23
5.9
.76
19.2
.22
5.5
.13
3.2
.04
1.0
.27
6.8
3 x
1.00
25.4
.75
19.1
.16
4.0
.05
Solder Cup
1.3
.10
Thru C'Sink
2.6
.18
x 82o
4.6
JF4SAB
JF4PAB
Side Mounting, 4 Position Rectangular, 2 and 4 Position In-Line
JF Series, PIN and Socket, 4 Position Rectangular Connectors
Dimensions shown are typical for all standard 4 position rectangular connectors.
.13
3.2
.06
1.6
.53
13.5
.44
11.1
.76
19.2
.04
1.0
.09
Thru C'Sink
2.3
.34
8.7
.17
4.4
.25
6.4
.22
5.5
.05
1.3
Solder Cup
.08
2.0
.28
7.1
.17
x 82o
4.3
JF2S2PAB
JF2P2SAB
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 79
Rack & Panel
Miniature Side Mount / # 20 Contacts / .040" Dia. / 7.5 Amps
JF Series
J F-2P
20 connectors assembled
The versitile JF Series has a countersunk
mounting hole and narrow width permitting
exceptionally flat mounting. Maximum circuit
density is provided with many positive
polarizations. “Custom” multi-contact
connectors are readily available by using the
building block technique shown above.
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
Typical Connector With
DIP Solder Termination
Right Angle
Dip Solder
Straight
Dip Solder
JF Series connectors may be ordered with dip
solder and right angle terminations. Consult factory
for availability.
D
.03
0.8
JF1S1PD4
.343
.437
90o
.062
R.025
.125
Typical Connectors Assemblies
PIN Contact
Pos. B
PIN Contact
Pos. C & D
2x
2x
.237 ±.015
.025
Socket Contact
Pos. C & D
PIN Contact
Pos. A, C & D
Socket Contact
Pos. B
Socket Contact
Pos. A, C & D
C
Socket
Molding
B
B
A
A
Socket Contact
Pos. A
JF1S1PA
PIN
Molding
PIN Contact
Pos. A
JF1P1SA
Socket
Molding
Socket
Contact
Pos. A & B
JF4SAB
PIN
Contact
Pos. A & B
JF4AB
PIN
Molding
Socket
Molding
A
B
Socket
Contact Pos. B
JF1S3PB
C
A
PIN
Molding
PIN Contact
Pos. B
B
JF1P3SB
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 80
Rack & Panel
Miniature Side Mount / # 20 Contacts / .040" Dia. / 7.5 Amps
JF Series
ORDERING INFORMATION
2 Position In-Line Connector
JF
1S
1P
A
■ Step 1
■ Step 2 **
■ Step 3
■ Step 4
Series Code
JF
Primary Contact and Molding Type
Secondary Contact
Primary Contact Location
Code
1S or 2S*
1P or 2P*
2SR*
2PR*
Description
Code
If Step 2 equals
Number of socket contacts
1P =
1S
and socket molding.
1S =
1P
Number of pin contacts and
pin molding.
Number of socket contacts
pin moldings.
Number of pin contacts
socket moldings.
*For two same type contacts, skip Steps 3 & 4.
Code = A or B
4 Position In-Line Connectors
JF4
S
■ Step 1
■ Step 2
Series Code
JF4
Primary Contact and
Molding Type
Code
S
P
AB
■ Step 3
Primary Contact Location
**
Description
Socket contact and
socket molding.
Pin contact and
pin molding.
Number Of
Primary Contacts
A, B, C or D
= 1
AB, AC, AD, BC, BD, or CD
= 2
ABC, ABD, ACD, or BCD
= 3
Code
For four same type contacts: omit step
For four same type contacts with molding gender
reversed, add R
4 Position Rectangular Connector
JF
2S
2P
AB
■ Step 1
■ Step 2 **
■ Step 3
Series Code
JF
Primary Contact and Molding Type
Secondary Contact
Primary Contact Location
Code
1S, 2S, 3S or 2S2S
Code
3P =
2P =
1P =
3S =
2S =
1S =
Code
Description
Number of socket contacts
and socket molding.
1P, 2P, 3P or 2P2P* Number of pin contacts and
pin molding.
2S2SR*
Number of socket contacts
and pin molding.
2P2PR
Number of pin contacts and
socket molding.
*For four same type contacts, skip Steps 3 & 4.
■ Step 4
If Step 2 equals
1S
2S
3S
1P
2P
3P
Number Of
Primary Contacts
A, B, C or D
= 1
AB, AC, AD, BC, BD, or CD
= 2
ABC, ABD, ACD, or BCD
= 3
**For Pictorial Presentation, see RP/84 and RP/85
SPECIFICATIONS
Winchester/Retconn
Materials
Performance Characteristics
Moldings (PIN
and Socket): Diallyl Orthophthalate
Pin Contacts: .040 Brass, gold plated
Socket
Contacts:
Phosphor bronze,
gold plated
Dielectric
Withstanding
Voltage:
Current Rating:
Operating
Temperature Range:
Termination Type:
1500 VAC (at sea level)
7.5 Amps
-55OC to +125OC
.050 dia. solder cup to accept
#20 AWG stranded wire.
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 81
Rack & Panel
J FA Series
Miniature Side Mount / # 16 Contacts / .062" Dia. / 13 Amps
JFA2H
Hood
JFA2S
Receptacle
JFA2H — JFA2P
Hood and plug
For applications in electronic and communications equipment requiring miniature connectors with high current capacity.
Series JFA miniature connectors may be
used in television, radio and communications
equipment. The countersunk side mounting
hole and narrow width permits exceptionally
flat mounting —thereby minimizing connector
protrusion when installed on equipment
Current Rating: 13 amps
No. of
Contacts:
2
Pin Contacts: .062 dia. brass, gold plated
Socket
Contacts:
Phosphor bronze, gold plated
Terminations: .070 dia. solder cup will
accept up to #16 AWG
stranded wire.
Electrical Data:Dielectric withstanding
voltage is one minute
electrification at 2925 VAC.
Dielectric:
Molded diallyl phthalate
per MIL-M-14
Hood:
Locked to connector by
means of two side mounted
straps.
SPECIFICATIONS
OUTLINE
Dimensions are for reference only and
are subject to change. Outline drawings
on request.
.78
.53
.25
.53
.34
.34
JFA2H
JFA 2
.44
.218
.22
.44
070 DIA
SOLDER CUP
.0625 DIA
.089 DIA HOLE
.203 DIA. X 82
C'SINK BOTH
SIDE S (TYP)
O
.172
.172
J FA-2S
Receptacle
PHYSICAL DATA AND
ORDERING INFORMATION
JFA-1P1S
JFA-2PH
JFA-2SH
JFA-2P
JFA-2S
(no-strapson hoods)
Winchester/Retconn
.34
J FA-2H
Hood
Mating Combinations
Number Current Wire
Weight
of
Rating
Size
Ozs.
Contacts Amps A.W.G.
1 Pin
.082
1 Socket
2 Pins
13
# 16
.059
2 Sockets
.046
JFA2P
mates with
JFA2S
JFA2PH
mates with
JFA2SH
JFA1P1S-A
mates with
JFA1S1P-A
JFA1P1S-B
mates with
JFA1S1P-B
JFA1P1SH-A
mates with
JFA1S1PH-A
1 Pin
1 Socket
2 Pins
2 Sockets
JFA1P1SH-B
mates with
JFA1S1PH-B
(with hoods)
JFA-1S1P
.172
J FA-2P
Plug
Physical Data
Code
Number
.13
.25
.082
13
# 16
.059
.046
JFA2H — Hood — used on any of above 3 parts
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 82
Rack & Panel
Removable Contacts
100 Series
6x Actual Size — Typical Removable Contact
Winchester Electronics removable contacts
allow quick, easy removal and replacement of
any contact without disturbing another - and
without discarding the connector. They offer
exceptional flexibility in both the choice and
revision of circuitry for rack and panel
equipment ... at substantial savings in
replacement and installation time. In addition,
wiring costs are significantly lowered, as
wires may be assembled away from the
connector itself. Assembly of contacts to
wires is further simplified by crimp type
contacts. A contact is slipped on the wire,
inserted in the crimping tool, and crimped
securely in place in seconds. Compact and
self-aligning, these removable contacts
provide high retention force and exceptional
mechanical and electrical reliability. Solder
type removable contacts are available for
connectors using MRAC contacts.
Pin Contacts:
Specifications: Conforms to applicable
portions of MIL-C-39029
Wire Sizes:
From a minimum 28 to a
maximum 14 AWG. All
contacts are designed to
accept a minimum AWG
conductor up to two sizes
below maximum gage
(each contact.)
Termination
Types:
Crimp, solder, dip solder or
wire-wrap
SPECIFICATIONS
Socket
Contacts:
Tools:
Military
Copper Alloy, gold plated.
Closed entry type machined
from copper alloy, gold
plated.
Complete line available.
Includes automatic pneumatic, pneumatic hand
operated, hand operated
crimping tools, insertion and
removal tools.
Current Rating: 7.5 Amps maximum for .040
contacts. 13 Amps maximum
for .062 contacts.
To Order: Specify by catalog number
Note:
Series 100 Removable Contacts are not supplied with the
connector. They must be ordered as a separate item.
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 83
RP / 84
.081
.067
.067
.052
.052
.045
.045
.033
.033
.027
.027
.024
.024
.067
.067
.052
.052
.045
.045
.033
.033
.027
.027
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
100-1014S 100-0919S 14-16
100-1016P 100-0911P 16-18-20
100-1016S 100-0921S 16-18-20
100-1018P 100-0913P 18-20-22
100-1018S 100-0923S 18-20-22
100-1020P 100-0915P 20-22-24
100-1020S 100-0925S 20-22-24
100-1022P 100-0907P 22-24-26
100-1022S 100-0908S 22-24-26
100-1024P 100-0917P 24-26-28
100-1024S 100-0927S 24-26-28
100-1026P 100-0963P 26-28-30
100-1026S 100-0965S 26-28-30
100-2016P 100-0949P 16-18-20
100-2016S 100-0939S 16-18-20
100-2018P 100-0943P 18-20-22
100-2018S 100-0933S 18-20-22
100-2020P 100-0945P 20-22-24
100-2020S 100-0935S 20-22-24
100-2022P 100-0947P 22-24-26
100-2022S 100-0937S 22-24-26
100-2024P 100-0951P 24-26-28
100-2024S 100-0941S 24-26-28
A
.055
.055
.055
.055
.065
.065
.078
.078
.096
.096
.050
.050
.055
.055
.055
.055
.065
.067
.040
.040
.040
.040
.040
.040
.040
.040
.040
.040
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
4
3
4
3
4
3
4
3
4
3
2
1
2
1
2
1
2
1
2
1
2
1
2
1
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
13
13
13
13
13
13
13
13
13
13
13
13
13
13
Mating Description See AMPS
Pin
of
Figure per
Diameter Contacts Number Cont
Hand
Tool
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
Locator
For Loose Contacts
For Reeled Contacts
5431-15
5431-15
5431-15
5431-15
5431-15
5431-15
5431-14
5431-14
5431-14
5431-14
5431-15
5431-15
5431-15
5431-15
5431-15
5431-15
5431-15
5431-15
5431-14
5431-14
5431-14
5431-14
5431-22
5431-22
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0970
107-0976
107-0976
107-0976
107-0976
107-0976
107-0976
107-0977
107-0977
107-0977
107-0977
107-0976
107-0976
107-0976
107-0976
107-0976
107-0976
107-0976
107-0976
107-0977
107-0977
107-0977
107-0977
107-0981
107-0981
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0965
107-0965
107-0965
107-0965
107-0965
107-0965
107-0966
107-0966
107-0966
107-0966
107-0965
107-0965
107-0965
107-0965
107-0965
107-0965
107-0965
107-0965
107-0966
107-0966
107-0966
107-0966
107-0966
107-0966
5431-15
5431-15
5431-15
5431-15
5431-15
5431-15
5431-14
5431-14
5431-14
5431-14
5431-15
5431-15
5431-15
5431-15
5431-15
5431-15
5431-15
5431-15
5431-14
5431-14
5431-14
5431-14
5431-14
5431-14
Continued on page RP / 85
5431-12
5431-12
5431-12
5431-12
5431-12
5431-12
5431-11
5431-11
5431-11
5431-11
5431-12
5431-12
5431-12
5431-12
5431-12
5431-12
5431-12
5431-12
5431-11
5431-11
5431-11
5431-11
5431-17
5431-17
Gage Plug Hand Tool Positioner Gage Plug Pneumatic
Depth
Gage Plug
Pneumatic
Part
Part
Part
Part
Tool Part Block Part
Part
Tool
Number
Number
Number
Number
Number
Number
Number
For Loose Contacts
100 Series
.078
.078
.097
.092
.105
.105
B
Diameter
(See Drawings)
.081
Used In
Connector
Series
MRAC, TMRAC,
XAC, TXAC
Reeled
Contact
AccomPart
modates
Number Conductor
2,000/Reel
Sizes
100-1014P 100-0909P 14-16
Loose
Contact
Part
Number
100 SERIES CONTACTS
Rack & Panel
Removable Contacts
100 SERIES CONTACTS
14-16-18
16-18-20
16-18-20
18-20-22
18-20-22
20-22-24
Not
100-2514S
Available
Not
100-2516P
Available
Not
100-2516S
Available
Not
100-2518P
Available
Not
100-2518S
Available
Not
100-2520P
Available
.052
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
100-51014S 100-0981S 14-16
100-51016S 100-0982S 16-18-20
100-51018S 100-0983S 18-20-22
100-51020S 100-0984S 20-22-24
.067
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
.081
SREC, 42 Series
100-4028S 100-0810S 28-30
.045
.067
.078
.094
.105
See Drawing
See Drawing
SREC, 42 Series
.065
.065
See Drawing
.045
.045
.096
100-4028P 100-0809P 28-30
MRAC, TMRAC,
XAC, TXAC
.067
See Drawing
20-22-24
Not
100-2620S
Available
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
.096
100-4024S 100-0806S 24-26-28 SREC, 42 Series
20-22-24
Not
100-2620P
Available
.067
.055
See Drawing
16-18-20
Not
Available
100-2616S
MRAC, TMRAC,
XAC, TXAC
.027
.055
100-4024P 100-0805P 24-26-28 SREC, 42 Series
16-18-20
Not
Available
100-2616P
MRAC, TMRAC,
XAC, TXAC
.027
.055
See Drawing
24-26-28
Not
Available
100-2524S
MRAC, TMRAC,
XAC, TXAC
.033
.055
.065
SREC, 42 Series
24-26-28
Not
Available
100-2524P
MRAC, TMRAC,
XAC, TXAC
.033
.045
100-4020S 100-0802S 20-22
22-24-26
Not
Available
100-2522S
MRAC, TMRAC,
XAC, TXAC
.065
.076
.076
.097
.097
.105
.105
B
SREC, 42 Series
22-24-26
.045
.052
.052
.067
.067
.081
.081
A
Diameter
(See Drawings)
100-4020P 100-0801P 20-22
20-22-24
Not
Available
100-2522P
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
MRAC, TMRAC,
XAC, TXAC
Used In
Connector
Series
.062
.062
.062
.062
.030
.030
.030
.030
.030
.030
.040
.040
.040
.040
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
.062
24
25
26
27
28
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
3 Piece
Crimp
3 Piece
Crimp
3 Piece
Crimp
19
19
19
19
23
Crimp
Contact
3 Piece
Crimp
8
Crimp
Contact
7
8
7
6
5
6
5
6
5
6
5
6
5
6
5
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
Solder
Contact
13
13
13
13
5
5
5
5
5
5
7.5
7.5
7.5
7.5
13
13
13
13
13
13
13
13
13
13
13
13
Mating Description See AMPS
Pin
of
Figure per
Diameter Contacts Number Cont
107-43300
107-43300
107-43300
107-43300
107-43300
107-43300
Hand
Tool
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-43302
107-43302
107-43302
107-43302
107-43302
107-43302
Locator
For Loose Contacts
For Reeled Contacts
5431-15
5431-14
5431-14
5431-14
5431-25
5431-25
5431-25
5431-25
5431-25
5431-25
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
N/A Solder Contact
107-0965
107-0966
107-0966
107-0966
107-0965
107-0965
107-0965
107-0965
107-0965
107-0965
5431-15
5431-14
5431-14
5431-14
5431-15
5431-15
5431-15
5431-15
5431-15
5431-15
Continued on page RP / 86
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
107-0961
Gage Plug Hand Tool Positioner Gage Plug Pneumatic
Depth
Gage Plug
Pneumatic
Part
Part
Part
Part
Tool Part Block Part
Part
Tool
Number
Number
Number
Number
Number
Number
Number
For Loose Contacts
100 Series
Not
100-2520S
Available
100-2514P
14-16-18
Reeled
Contact
AccomPart
modates
Number Conductor
2,000/Reel
Sizes
Not
Available
Loose
Contact
Part
Number
100 SERIES CONTACTS
Rack & Panel
Removable Contacts
100 SERIES CONTACTS
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 85
RP / 86
SREC, 42 Series
SREC, 42 Series
100-54020S 100-0804S 20-22
100-54024S 100-0823S 24-26
Not
100-54028S
Available
RG178,
196/U
RG178,
196/U
Not
Available
Not
100-8000S
Available
.050
See Drawing
See Drawing
Not Applicable
Not
RG174,188 MRAC, TMRAC,
Available
316/U
XAC, TXAC
Not
RG174,188 MRAC, TMRAC,
Available
316/U
XAC, TXAC
Dip
Solder
Dip
Solder
Wire
Wrap
Wire
Wrap
Dip
Solder
Dip
Solder
Wire
Wrap
Wire
Wrap
Wire
Wrap
Wire
Wrap
Not
Available
Not
Available
Not
Available
Not
Available
Not
Available
Not
Available
Not
Available
Not
Available
Not
Available
Not
Available
100-8003P
100-8003S
7130
7131
8122
8123
8124
8125
8113
8114
8105
8106
100-S = Military Contacts
See Drawing
Not
RG161,179 MRAC, TMRAC,
Available
187/U
XAC, TXAC
100-8001S
MRAC, TMRAC
MRAC, TMRAC
MRAC, TMRAC
MRAC, TMRAC
MRAC, TMRAC
MRAC, TMRAC
SREC
SREC
MRAC, TMRAC
Not Applicable
Not Applicable
Not Applicable
Not Applicable
Not Applicable
Not Applicable
Not Applicable
Not Applicable
Not Applicable
See Drawing
MRAC, TMRAC
See Drawing
Not
RG161,179 MRAC, TMRAC,
100-8001P
Available
187/U
XAC, TXAC
See Drawing
See Drawing
See Drawing
MRAC, TMRAC,
XAC, TXAC
100-8000P
MRAC, TMRAC,
XAC, TXAC
SREC, 42 Series
100-51026S 100-0987S 26-28-30
.055
.062
.062
.062
.062
.062
.062
.030
.030
.062
.062
.078
.078
.078
.078
.078
.078
.030
.030
.030
.062
.062
.062
21
Wire
Wrap
Wire
Wrap
Wire
Wrap
Wire
Wrap
Dip
Solder
Dip
Solder
Wire
Wrap
Wire
Wrap
Dip
Solder
Dip
Solder
Shielded
Crimp
Shielded
Crimp
Shielded
Crimp
Shielded
Crimp
Shielded
Crimp
Shielded
Crimp
17
18
15
16
12
11
14
13
10
9
32
31
32
31
32
31
22
20
3 Piece
Crimp
3 Piece
Crimp
19
3 Piece
Crimp
19
19
3 Piece
Crimp
3 Piece
Crimp
3 Piece
Crimp
13
13
13
13
13
5
5
5
13
13
—
—
—
—
—
—
5
5
5
13
13
13
Mating Description See AMPS
Pin
of
Figure per
Diameter Contacts Number Cont
Hand
Tool
107-43303
107-43303
107-43303
107-43303
107-43303
107-43303
107-43302
107-43302
107-43302
107-43300
107-43300
107-43300
107-43300
107-43300
107-43300
Inner
Contact
107-43300
107-43300
107-43300
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
107-0945 107-0903-2A 107-0918
Locator
For Loose Contacts
For Reeled Contacts
Outer
Contact
5431-26
5431-26
5431-26
5431-26
Not
Required
Not
Required
Not
Required
Not
Required
N/A Wire Wrap
N/A Wire Wrap
N/A Wire Wrap
N/A Wire Wrap
N/A Dip Solder
N/A Dip Solder
N/A Wire Wrap
N/A Wire Wrap
N/A Dip Solder
N/A Dip Solder
107-43330
107-43330
107-43330
107-43330
5431-26 107-0903-2A 107-0944
5431-26 107-0903-2A 107-0944
5431-25
5431-25
5431-25
5431-15
5431-15
5431-15
107-0965
107-0965
107-0965
5431-15
5431-15
5431-15
Continued on page RP / 87
107-0961
107-0961
107-0961
Gage Plug Hand Tool Positioner Gage Plug Pneumatic
Depth
Gage Plug
Pneumatic
Part
Part
Part
Part
Tool Part Block Part
Part
Tool
Number
Number
Number
Number
Number
Number
Number
For Loose Contacts
100 Series
28-30
.024
MRAC, TMRAC,
XAC, TXAC
100-51024S 100-0986S 24-26-28
.055
B
See Drawing
.027
MRAC, TMRAC,
XAC, TXAC
A
Diameter
(See Drawings)
.033
Used In
Connector
Series
MRAC, TMRAC,
XAC, TXAC
Reeled
Contact
AccomPart
modates
Number Conductor
2,000/Reel
Sizes
100-51022S 100-0985S 22-24-26
Loose
Contact
Part
Number
100 SERIES CONTACTS
Rack & Panel
Removable Contacts
100 SERIES CONTACTS
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
Winchester
Part
Number
100R-2020P95
100R-1020P95
100B-1016P95
100-202861-50
100R-2020S95
100R-51020S95
100B-51016S95
100-202862-50
M39029/34-271
M39029/34-272
M39029/34-273
M39029/34-440
M39029/35-274
M39029/35-275
M39029/35-276
M39029/35-441
22-24-26
16-18-20
20-22-24
20-22-24
22-24-26
16-18-20
20-22-24
20-22-24
Accommodates
Conductor
Sizes
M28748
M28748
M28748
M28748
M28748
M28748
M28748
M28748
Used In
Connector
Series
.035
.067
.045
.045
.035
.067
.045
.045
A
.056
.092
.067
.067
.056
.092
.067
.067
B
Diameter
1
1
29
4
19
19
30
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
Crimp
Contact
.030
.062
.062
.040
.030
.062
.062
5
13
13
7.5
5
13
13
7.5
3
Crimp
Contact
.040
AMPS
per
Cont
Mating Description
See
Pin
of
Figure
Dia.
Contacts Number
Winchester
Crimp
Tool
MIL Spec
Positioner
Buchn.614412
M22520/2-01 107-43300
Buchn.614412
M22520/1-01 107-0903-2A M22520/1-03
M22520/1-01 107-0903-2A M22520/1-03
M22520/1-01 107-0903-2A M22520/1-03
M22520/2-01 107-43300
M22520/1-01 107-0903-2A M22520/1-03
M22520/1-01 107-0903-2A M22520/1-03
M22520/1-01 107-0903-2A M22520/1-03
MIL Spec
Crimp
Tool
Insertion
Tool
MIL
Insertion
Tool
Winchester
Removal
Tool
MIL
Removal
Tool
Winchester
IT2857
M81969/20-02
RT2855
M81969/18-02
IT2857
M81969/20-02
RT2855
107-0945 M81969/18-01 107-1015 M81969/20-01 107R1001
107-0945 M81969/18-01 107-1015 M81969/20-01 107R1001
107-0945 M81969/18-01 107-1015 M81969/20-01 107R1001
107-0611 M81969/18-02
107-0945 M81969/18-01 107-1015 M81969/20-01 107R1001
107-0945 M81969/18-01 107-1015 M81969/20-01 107R1001
107-0945 M81969/18-01 107-1015 M81969/20-01 107R1001
Winchester
Positioner
100 Series
M39029
Part
Number
MIL-C-39029 CONTACTS
Rack & Panel
Removable Contacts
MIL-C-39029 CONTACTS
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 87
Rack & Panel
100 Series
Removable Contacts
OUTLINE
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 88
Rack & Panel
Removable Contacts
100 Series
OUTLINE
Figure 11
Figure 12
Figure 13
Figure 14
1.335
1.335
Figure 15
Figure 16
1.335
1.335
Figure 17
Figure 18
Accepts O.062 pin.
B
A
Figure 19
Figure 20
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 89
Rack & Panel
100 Series
Removable Contacts
OUTLINE
Figure 21
Figure 22
Figure 23
Figure 24
Figure 25
Figure 26
Figure 27
Figure 28
Accepts .030 pin.
Figure 29
Figure 30
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 90
Rack & Panel
100 Series
Removable Contacts
OUTLINE
Figure 31
Figure 32
ORDERING INFORMATION
Dimensions
Catalog
Number
Style
100-8000P
Pin
100-8000S
Socket
100-8001P
Pin
100-8001S
Socket
100-8003P
Pin
100-8003S
Socket
Cable Sizes
A
B
C
D
E
F
G
RG178/U
RG196/U
.797
.080
.120
.082
.057
.020
.036
RG161/U
RG179/U
RG187/U
1.031
.110
.137
.111
.082
.020
.063
RG174/U
RG188/U
RG316/U
1.031
.110
.137
.111
.082
.023
.063
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 91
Rack & Panel
107 Series
Crimping Tools And Accessories
PNEUMATIC AND HAND
CRIMPING TOOLS
Automatic Feed Crimping Tool
600/1200 Crimps Per Hour
Catalog Number 107-0961
Air operated tool provides for a large
capacity reel and foot valve control.
Crimp depths are accurately controlled
by interchangeable snap-in depth
blocks when the tool is bench
mounted. Leaves operator’s hands
free. (Does
not include reel or foot valve control.)
Includes crimp depth blocks.
Automatic Crimp Tool made up of
bench mount (107-0962) and crimp t
ool (107-0960). Used to crimp 10010**P/S, 100-20**P/S, 100-510**S
Series.
Winchester/Retconn
Pneumatic Hand Crimping Tool
400 Crimps Per Hour
Hand Operated Crimping Tool
200/300 Crimps Per Hour
Catalog Number 107-0918
Requires 80/120 psi. Crimp depth
adjustment made by internal screw.
Locators, adaptor sleeves, and gage
plugs should be ordered separately.
Locator 107-0945 and adapter
107-0950 supplied with tool.
Catalog Number 107-0903-2A
(Mil-T-22520 Class II Equivalent)
Gage plugs should be ordered separately. Locator 107-0945 and Spanner
wrench 107-1102 supplied with tool.
Miniature Hand Operated
Crimping Tool
Miniature Hand Operated
Crimping Tool
Catalog Number 107-43300
This miniature version of the MS
crimping tool is suited for the smaller
crimp contacts such as the SREC
series. It is only 7 1/2 inches long and
weighs 10 1/2 ounces. Positioners are
ordered separately.
Catalog Number 107-0625
Miniature tool with a continuously
variable crimp depth adjustment.
Locators must be ordered separately.
Hand Operated Crimping Tool
200/500 Crimps Per Hour
Tool Kit
Catalog Number 107-0970
MS—3191-2 (Mil-T-22520 Class I)
Ruggedly built hand tools with forged
body, and four indentors machined from
high grade tool steel. Size approximately 9 inches long. Weight approximately 19 ounces.
Catalog Number 107K4
Includes crimping tool 107-0903-2A,
locator 107-0945, insertion tool 107-1015,
removal tool 107R-1001, spanner wrench
107-1102 and go/no-go gages 5431.
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 92
Rack & Panel
Crimping Tools And Accessories
107 Series
Guide Set Tool
This tool provides fast and easy installation of G7 and N7 Guide Sets. Screwdriver type tips are
enclosed by cylindrical aligners that hold tips in place in the Guide pin and socket slots to prevent
slippage. Tool holds pin or socket in place while hex nut is tightened with hex wrench.
Catalog Number 107-0701
for MRE / MRA / MRAC G7 / N7 Guide
Catalog Number 107-0704
for MRE 5-3, 8 / SREC N Guide
Removable Contact
Insertion Tools
Catalog Number 107-1011
for SREC
Catalog Number 107-1015
for MRAC / STD & Shielded
Hex Wrench
Catalog Number 107R1001
for MRAC / STD
This tool provides fast and easy installation of
guides and fixed jacks. This tool may be used
with the guide set tool.
Catalog Number 107-0703
for MRE / MRA / MRAC (hex size 3/16)
Catalog Number 107-0708
for MRE 5-3, 8 / SRE / SREC (hex size 5/32)
Catalog Number 107-1005
for MRAC / STD & Shielded
Catalog Number 107-1012
for SREC
Catalog Number 107R1001
for MRAC / STD
Contact Pin Straightener
Gage Plug
Catalog Number 107-1024
used on .040 or .062 dia.
Catalog Number 5431
When ordering gage plugs,
please specify:
1. Tool
2. Contact Size
3. Wire Size
Positioners
Locators
Catalog
Number
Removable Contact
Removal Tools
Catalog
Number
Used With
Contact
Tool
107-0626
SREC
MRAC
107-0627
(Inner)
107-0625
Shielded
MRAC
107-0628 20, 22, 24, 26
107-0945
MRAC
MRAC
107-0902 &
107-43302
(Outer)
107-0903-2A
Shielded
107-0981
107-0977
107-0976
107-43302
107-43303
CRIMPING TOOLS
107-43304
Used With
Contact
Tool
MRAC Pin
and Socket
#14 & 16
MRAC Pin
and Socket
107-0970
#16 & 18
MRAC Pin
and Socket
#20, 22, 24, 26
SREC #20
& 24
MRAC
(Inner)
107-43300
Shielded
MRAC #20
22, 24, 26
Bench Mount For
Crimping Tool 107-0960
Crimp Depth Blocks For Crimping
Tools 107-0960 and 107-0961
Catalog Number 107-0962
includes crimp depth blocks
Catalog Numbers 107-0965 - #20,
107-0966 - #16, 107-0967 - #12
Spanner Wrench
Catalog Number 107-1102
for use with 107-0903-2A
Crimping Tool
Winchester/Retconn
199 Park Road Ext., Suite 104, Middlebury, Connecticut 06762 Phone:(203)741-5400 Fax:(203)741-5500 www.winchesterelectronics.com
RP / 93