Download Specification Sheet

SPECIFICATION
Model
:
Spec No.
:
Customer Approval Status
Dsg'd
:
Chk'd
:
App'd
:
File Publish Sign
Piezo Buzzer
ST-0503-3
SOBERTON
:
Edition
File clerk
File Publish Sign
A
:
≤£
® —
≥°
2014.11.21
211 North First Street Minneapolis, MN. 55401 ™ Ĺ ÿ
÷ˆ
Dsg'd
≤£
® —
≥°
2014.11.21
§˝™ k
∫Õ
Chk'd
≤£
® —
≥°
2014.11.21
App'd
Web-site: www.soberton.com
Sales
¥ ø
¨„
’∏
Kimberly Scheerer
MODEL NUMBER
CUSTOMER
NUMBER
ST-0503-3
PRODUCT TYPE
REVERSION
DATE
PAGE
Buzzer
A
2014-11-21
1/5
A. SCOPE
This specification applies magnetic buzzer, ST-0503-3
B. SPECIFICATION
No.
Item
Unit
Specification
Condition
1
Oscillation Frequency
Hz
4000
Vo-p=1/2duty , square wave
2
Operating Voltage
Vo-p
2~ 4
3
Rated Voltage
Vo-p
3
4
Current Consumption
mA
MAX. 110
at Rated Voltage
5
Sound Pressure Level
dB
MIN. 75
at 10cm at Rated Voltage
6
Coil Resistance
Ω
12±3
7
Operating Temperature
-20 ~ +60
8
Storage Temperature
-30 ~ +80
9
Dimension
mm
5.0 x 5.0 x H2.7
10
Weight (MAX)
gram
0.1
11
Housing Material
LCP( Black )
12
Leading Pin
Tin Plated Brass(Sn)
13
Environmental
Protection Regulation
RoHS
C. APPEARANCE DRAWING
-
喷墨印字
Tol : ± 0.3
Unit: mm
See appearance drawing
See appearance drawing
MODEL NUMBER
CUSTOMER
NUMBER
ST-0503-3
PRODUCT TYPE
REVERSION
DATE
PAGE
Buzzer
A
2014-11-21
2/5
D.TESTING METHOD
Standard Measurement conditions
Temperature:25±2℃
Humidity:45-65%
Acoustic Characteristics:
The oscillation frequency, current consumption and sound pressure are measured by the
measuring instruments shown below
In the measuring test, buzzer is placed as follows:
E. Typical Frequency Response Curve
MODEL NUMBER
CUSTOMER
NUMBER
ST-0503-3
PRODUCT TYPE
REVERSION
DATE
PAGE
Buzzer
A
2014-11-21
3/5
F. Recommend Driving Circuit
The base current Ib should high enough so that it saturates the collector current of the transistor with the CB load.
G. Soldering Condition
(1)Recommendable reflow soldering condition is as follows
(Reflow soldering is twice)
Note:It is requested that reflow soldering should be executed
after heat of product goes down to normal.
Heat resistant line
(Used when heat resistant reliability test is performed)
(2)Manual soldering
Manual soldering temperature 350º C within 5 sec.
MODEL NUMBER
CUSTOMER
NUMBER
ST-0503-3
PRODUCT TYPE
REVERSION
DATE
PAGE
Buzzer
A
2014-11-21
4/5
H. RELIABILITY TEST
NO.
ITEM
1
High Temperature
Test (Storage)
2
Low Temperature
Test (Storage)
After being Placed in a chamber with -30ð2ºC for 96 hours and then
being placed in normal condition for 2 hours.
Allowable variation of SPL after test: ð10dB.
Humidity Test
After being Placed in a chamber with 90-95% R.H. at 40ð2ºC for 96
hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: ð10dB.
3
TEST CONDITION AND REQUIREMENT
After being placed in a chamber with 80ð2ºC for 96 hours and then
being placed in normal condition for 2 hours.
Allowable variation of SPL after test: ð10dB.
The part shall be subjected to 5 cycles. One cycle shall be consist of:
+60ºC
+25ºC
+25ºC
4
Temperature Cycle
Test
20ºC
Allowable variation of SPL after test: ð10dB.
5
6
Drop on a hard wood board of 4cm thick, any directions ,6 times,
at the height of 75cm .
Allowable variation of SPL after test: ð10dB.
Drop Test
Vibration Test
7
Solderability
Test
8
Terminal Strength
Pulling Test
After being applied vibration of amplitude of 1.5mm with 10 to 55 Hz
band of vibration frequency to each of 3 perpendicular directions for
2 hours .
Allowable variation of SPL after test: ð10dB.
Lead terminals are immersed in rosin for 5 seconds and then
immersed in solder bath of +300ð5ºC for 3ð1 seconds .
90% min. lead terminals shall be wet with solder
(Except the edge of terminals).
The force of 9.8N(1.0kg) is applied to each terminal in axial direction for
10 seconds.
No visible damage and cutting off.
TEST CONDITION.
Standard Test Conditio :
a) Temperature : +5 ~ +35℃
Judgment Test Conditio
:
b) Humidity : 45-85%
a) Temperature : +25 ± 2℃
b) Humidity : 60-70%
c) Pressure : 860-1060mbar
c) Pressure : 860-1060mbar
ST-0503-3
Buzzer
A
2014-11-06
I. PACKING STANDARD
1 Reel : 2500PCS
Carton Box
(10 Inner Box)
Inner Box
(1Layer Reel)
Inner Box
330mmx330mmx30mm
1x2500PCS=2500PCS
Carton Box
350mmx350mmx370mm
10x2500PCS=25,000PCS
5/5