TD4PX series electronic roll-over switch • Roll-over detection and fuel cut-off • Wide trigger angle with 2° Hysteresis • 3 sec delay on trigger and reset angle standard • Non resettable - one shot optional • Optional reset by external module or auto reset after 90s • Up to 1A output to drive up to 2 x mini-ISO relays • Optional LED for trip status indication Specifications Output RoHS Compliant PNP (see Fig. 3 for details) Output load DC 0.5A (max.) Short circuit protection Yes Supply voltage DC 8 - 30V Current consumption ≤ 25mA Polarity protection Yes Boot up time <10ms Housing Plastic injection moulded (PBTP) Dimensions (approx.) L x W x H 40 x 40 x 25mm Mounting M3 screws Connection M12 5 pin male connector (others to special order) Weight approx. 50g Ambient temperature -25°C to +85°C (storage and operating) Humidity 0 - 95% non-condensing Sealing IEC60529 IP67 Shock resistance Measuring range max. 10g detection angle ± 40° standard, other angles can be specified - see ordering code Centering function Frequency response pre-centered at 0°, range ±5° (-3dB) 0 - 0.1Hz Accuracy ±5° Offset Error 0° (after factory zeroing) Resolution 0.09° Temperature coefficient ±0.04°/K Page 1 of 3 www.aecsensors.com Ref: TD4PX Series 011916JHM Sales Department Tel: (888) 847-6552 Specifications are subject to change without notice. E&OE. TD4PX series electronic roll-over switch Fig. 1 Dimensions and mounting holes Optional LED position 5 M12 5p Male connector 1 2 4 3 Pin 1: Pin 2: Pin 3: Pin 4: Pin 5: +Supply Voltage Reset function (pin fitted but not connected for non-resettable version) Gnd (0V) Output Factory use (Centering/zero set) - leave unconnected. All dimensions in millimeters. Not to scale. Ordering Codes T D 4 P X - 0 4 0 - D S M - P N Series type P - P * * * * * P***** = Reserved for custom / specific versions Trigger Angle (in 1°steps) (040 = 40°) P00001= non-resettable, with LED status indicator, 1 second delay D = 10 - 30VDC P00002 = Externally resettable1 with LED status indicator, 1 second delay S = Standard Accuracy M = Medium Accuracy H = High accuracy X = Extra high Accuracy P00003 = auto reset after 90s delay, with LED status indicator, 1 second delay PNP Output to drive up to 2 x mini-ISO automotive relays Terminations Leave empty for 2000mm PUR Cable Empty cable length in mm if not 2000mm M = M12 Male connector (pins) F = F12 Female connector (socket) Page 2 of 3 www.aecsensors.com Ref: TD4PX Series 011916JHM 1 External reset requires an optional external configurator box Sales Department Tel: (888) 847-6552 Specifications are subject to change without notice. E&OE. TD4PX series electronic roll-over switch Mounting Orientation Fig. 2 The default 0 ° position is when the switch is mounted horizontally and no acceleration (or tilt) is applied. When mounting, please ensure sufficient space is left to allow for the cable (not supplied) and connector. Undue stress on the cable and connector should be avoided. Output Function Fig. 3 PNP out (Vsupply) (with external pull-down resistor) V unsafe area 0 unsafe area safe area - 40+ 0 + 40 The PNP output is designed to drive up to 2 standard 12VDC mini-ISO automotive relays in parallel, such as the Durakool DG85 series. If driving relays a pull-down resistor is not required. When the switch is in the safe area (tilt angle is less than ± 40°), the output is high and the relay is driven on. If the switch is tilted such that it detects an angle greater than 40° then the output goes low and the relay is turned off. If the switch is unpowered, the output is off. Once the switch has detected an over angle, there is a 3 second (optional 1 s) delay and the output goes low and stays low, even if the power to the switch is removed and re-applied. If the reset option is specified, the switch can be reset using a separate “configurator” module. The optional LED illuminates if the switch has detected an over angle and the output is low. The LED will turn off if power to the switch is removed, but will turn on again when power is re-applied (until reset for resettable versions). Page 3 of 3 American Electronic Components Inc., 1101 Lafayette St. Elkhart, IN46516 www.aecsensors.com Sales Department Tel: (888) 847-6552 Ref: TD4PX Series 011916JHM Specifications are subject to change without notice. E&OE.