Datasheet

TD4PO series
electronic tilt switches
• Omni-directional (horizontal plane)
• up to 2 x trigger angles
• PNP or NPN outputs
• 0.1A continuous output (max. 250mA 10s)
• M12 Male Connector or wire ended
• Replaces TQG Series
• RoHS Compliant
Specifications
Output
dual PNP or NPN (see Fig. 3 for details)
Output load
Short circuit protection
Supply voltage
DC 150mA continuous, 250mA max.10 sec (protected against back EMF)
Yes (10s max)
DC 8 - 30V
Current consumption
≤ 25mA
Polarity protection
Yes
Boot up time
<10ms
Housing
Plastic injection moulded (PBTP) (Contact factory for other options)
Dimensions (approx.)
L x W x H 40 x 40 x 25mm
Mounting
M3 screws
Connection
M12 5 pin male connector (others to special order) or PUR cable
Weight
approx. 50g
Ambient temperature
-25°C to +85°C (storage and operating)
Relative humidity
Sealing
0 - 100%
IEC60529 IP67
Shock resistance
Measuring range
Centering function
Frequency response
max. 10g
detection angles 2 x omni-directional switch points factory programmable
pre-centered at 0°, range ±5°
(-3dB) 0 - 0.5Hz
Accuracy
±0.4°
Offset Error
0° (after zeroing / centering)
Resolution
0.09°
Temperature coefficient
Page 1 of 3 www.aecsensors.com
Ref: TD4PO Series 012016JHM
typical ±0.04°/K
Sales Department Tel: (888) 847-6552
Specifications are subject to change without notice. E&OE.
TD4PO series
electronic tilt switches
Fig. 1
Dimensions and mounting holes
5
M12 5p Male connector
1
2
4
3
Pin 1:
Pin 2:
Pin 3:
Pin 4:
Pin 5:
+Supply Voltage
Output 1 Omni-directional
Gnd (0V)
Output 2 Omni-directional
Factory use (Centering/zero set) - leave unconnected in normal use.
All dimensions in millimeters.
Not to scale.
Ordering Codes
T
D
4
P
O
-
0
3
0
-
0
4
5
-
D
S
M
-
N
P
N
-
Series type
P
*
*
*
*
*
P***** = Reserved for
customer specific versions
1st Trigger Angle (in 1°steps)
(less than 2nd trigger angle)
NPN = Switched NPN Output
PNP = Switched PNP Output
2nd Trigger Angle (leave empty if
only one trigger angle)
Terminations
D = 10 - 30VDC
Leave empty for 2000m PUR Cable
5 = 5VDC
Enter cable length in mm if not 2000mm
S
=
Standard Accuracy
M
=
Medium Accuracy
H
=
High Accuracy
X
=
Extra High Accuracy
Page 2 of 3
www.aecsensors.com
Ref: TD4PO Series 012016HM
Sales Department Tel: (888) 847-6552
M
=
M12 Male connector (pins)
F
=
F12 Female connector (socket)
Specifications are subject to change without notice. E&OE.
TD4PO series
electronic tilt switches
Mounting Orientation
Fig. 2
The default 0 ° position is when the switch is mounted horizontally and no acceleration (or tilt) is applied.
When mounting, please ensure sufficient space is left to allow for the cable (when selected) or the M12 connector. Undue stress on
the cable and connector should be avoided.
Output Function
PNP Output:
- at 0° ; safe area, outputs 1 & 2: conducting.
Fig. 3
PNP Out (Vsupply) with external pull down resistor
trigger angle 2
- at trigger 1 angle; alert area, output 1: non-conducting
V
trigger angle 1
unsafe area
safe area
alert area
unsafe area
NPN Output:
- at 0° ; safe area, outputs 1 & 2: non-conducting.
alert area
-at trigger 2 angle; unsafe area, outputs 1 & 2: non-conducting
- at trigger 1 angle; alert area, output 1: conducting.
0V
-at trigger 2 angle; unsafe area, outputs 1 & 2: conducting.
0˚
trigger angle 2
V
unsafe area
safe area
alert area
unsafe area
Hysteresis: 0.2° Safe > unsafe delay = 500ms. Unsafe >
safe delay = 1000ms.
alert area
trigger angle 1
If the switch is unpowered, the outputs are off (non-conducting).
0V
0˚
NPN Out (Vsupply) with external pull up resistor
Centering (zeroing) should be done within 1 minute after power up.
After zeroing, there is an extra 1 minute left to repeat the centering.
Connect the centering input to ground for more than 0.5s
In normal use, the centering input pin should be left unconnected.
This device is not a “safety” device. For full redundancy (ISO13849), two devices should be used in the application.
Page 3 of 3
American Electronic Components Inc., 1101 Lafayette St. Elkhart, IN46516
www.aecsensors.com
Sales Department Tel: (888) 847-6552
Ref: TD4PO Series 012016JHM
Specifications are subject to change without notice. E&OE.