uClamp1211T Low Profile μClampTM 1-Line ESD protection PROTECTION PRODUCTS - MicroClampTM Description Features The μClamp series of TVS arrays are designed to protect sensitive electronics from damage or latch-up due to ESD. It is designed to replace multilayer varistors (MLVs) in portable applications such as cell phones, notebook computers, and other portable electronics. It features large cross-sectional area junctions for conducting high transient currents. They offer desirable characteristics for board level protection including fast response time, low operating and clamping voltage, and no device degradation. The μClampTM1211T is in a 2-pin, RoHS/WEEE compliant, SLP1006P2T package. It measures 1.0 x 0.6 mm with a nominal height of only 0.4mm. The leads are spaced at a pitch of 0.65mm and are finished with lead-free NiPdAu. Each device will protect one line operating at 12 volts. It gives the designer the flexibility to protect single lines in applications where arrays are not practical. They may be used to meet the ESD immunity requirements of IEC 61000-4-2, Level 4 (±15kV air, ±8kV contact discharge). The combination of small size and high ESD surge capability makes them ideal for use in portable applications such as cellular phones, digital cameras, and MP3 players. TM Transient protection for data lines to IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact) IEC 61000-4-4 (EFT) 40A (tp = 5/50ns) Cable Discharge Event (CDE) Ultra-small package (1.0 x 0.6 x 0.4mm) Protects one data or power line Low reverse current: <1nA typical (VR=12V) Working voltage: - 12V / +12V Low capacitance: 3pF typical Solid-state silicon-avalanche technology Mechanical Characteristics SLP1006P2T package RoHS/WEEE Compliant Nominal Dimensions: 1.0 x 0.6 x 0.4 mm Lead Finish: NiPdAu Molding compound flammability rating: UL 94V-0 Marking : Marking code, cathode band Packaging : Tape and Reel Applications Dimensions Cellular Handsets & Accessories FM Antennas RFID Keypads, Side Keys, LCD Displays Battery, Power Lines Notebooks & Desktop Computers Portable Instrumentation Schematic & PIN Configuration 1.0 2 0.60 0.65 1 0.40 Nominal Dimensions (mm) Revision 01/15/2009 SLP1006P2T (Bottom View) 1 www.semtech.com uClamp1211T PROTECTION PRODUCTS Absolute Maximum Rating R ating ESD p er IEC 61000-4-2 (Air) ESD p er IEC 61000-4-2 (Contact) Op erating Temp erature Storage Temp erature Symbol Value Units VESD +/- 18 +/- 12 kV TJ -55 to +125 °C TSTG -55 to +150 °C Electrical Characteristics (T=25oC) Parameter Symbol Conditions Reverse Stand-Off Voltage VRWM Pin 1 to 2 or 2 to 1 Reverse Breakdown Voltage V BR It = 1mA Pin 1 to 2 or 2 to 1 Reverse Leakage Current IR VRWM = 12V, T=25°C Pin 1 to 2 or 2 to 1 Clamp ing Voltage VC IPP = 1A, tp = 8/20μs Pin 1 to 2 or 2 to 1 Junction Cap acitance Cj VR = 0V, f = 1MHz © 2009 Semtech Corp. 2 Minimum 13.3 Typical Maximum Units 12 V 16 19 V <1 50 nA 27 V 7 pF 3 www.semtech.com uClamp1211T PROTECTION PRODUCTS Non-Repetitive Peak Pulse Power vs. Pulse Time Clamping Voltage vs. Peak Pulse Current 35 30 Clamping Voltage - VC (V) Peak Pulse Power - PPP (kW) 10 1 0.1 25 20 15 10 Waveform Parameters: tr = 8μs td = 20μs 5 0.01 0.1 1 10 0 100 0 0.5 Pulse Duration - tp (us) 1.5 Typical Insertion Loss (S21) Normalized Junction Capacitance vs. Reverse Voltage CH1 S21 CJ(VR) / CJ(VR=0) 1 Peak Pulse Current - IPP (A) 1.5 1.4 1.3 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 LOG 6 dB / REF 0 dB 1: -0.9411 dB 800 MHz f = 1 MHz 2: -1.0210 dB 800 MHz 0 dB 4 12 3 -6 dB 3: -2.5550 dB 1.8 GHz -12 dB 4: -5.1437 dB 2.5 GHz -18 dB -24 dB -30 dB -36 dB -42 dB 0 1 2 3 Reverse Voltage - VR (V) 4 5 -48 dB 1 MHz 10 MHz 100 MHz START . 030 MHz STOP 3000. 000000 MHz ESD Clamping (Pin 1 to 2 and 2 to 1) (-8kV Contact per IEC 61000-4-2) ESD Clamping (Pin 1 to 2 and 2 to 1) (8kV Contact per IEC 61000-4-2) Note: Data is taken with a 10x attenuator © 2009 Semtech Corp. 3 1 GHz GHz Note: Data is taken with a 10x attenuator 3 www.semtech.com uClamp1211T PROTECTION PRODUCTS Applications Information Device Connection Options Circuit Diagram These TVS diodes are designed to protect one data, I/O, or power supply line. The device is bidirectional and may be used on lines where the signal polarity can go above and below ground. Circuit Board Layout Recommendations for Suppression of ESD. Good circuit board layout is critical for the suppression of ESD induced transients. The following guidelines are recommended: z Place the TVS near the input terminals or connectors to restrict transient coupling. z Minimize the path length between the TVS and the protected line. z Minimize all conductive loops including power and ground loops. z The ESD transient return path to ground should be kept as short as possible. z Never run critical signals near board edges. z Use ground planes whenever possible. © 2009 Semtech Corp. 4 www.semtech.com uClamp1211T PROTECTION PRODUCTS Applications Information - Spice Model Spice Model uClamp1211T Spice Parameters © 2009 Semtech Corp. Parameter Unit D1 (T VS) D2 (T VS) IS Amp 2.21E-14 2.21E-14 BV Volt 16.4 16.4 VJ Volt 0.7 0.7 RS Ohm 2.7 2.7 IB V Amp 1E-3 1E-3 CJO Farad 6E-12 6E-12 TT sec 2.541E-9 2.541E-9 M -- 0.06 0.06 N -- 1.1 1.1 EG eV 1.11 1.11 5 www.semtech.com uClamp1211T PROTECTION PRODUCTS Outline Drawing - SLP1006P2T A B D DIMENSIONS INCHES MILLIMETERS DIM MIN NOM MAX MIN NOM MAX E TOP VIEW A SEATING PLANE aaa C C A1 A A1 b D E e L R N aaa bbb .015 .016 .017 .000 .001 .002 .018 .020 .022 .035 .039 .043 .020 .024 .028 .026 BSC .008 .010 .012 .002 .004 .006 2 .003 .004 0.37 0.40 0.43 0.00 0.03 0.05 0.45 0.50 0.55 0.90 1.00 1.10 0.50 0.60 0.70 0.65 BSC 0.20 0.25 0.30 0.05 0.10 0.15 2 0.08 0.10 PIN 1 ID R bxN bbb C A B 2x L e BOTTOM VIEW NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). Land Pattern - SLP1006P2T Y (C) DIM C G X Y Z Z G X DIMENSIONS INCHES MILLIMETERS (.033) (0.85) .012 0.30 .024 0.60 .022 0.55 .055 1.40 NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. © 2009 Semtech Corp. 6 www.semtech.com uClamp1211T PROTECTION PRODUCTS Marking Code Ordering Information Part Number Working Voltage Qty per Reel Reel Size uClamp 1211T.TCT 12V 3,000 7 Inch PIN 1 ID SS Notes: 1) This is a lead-free, RoHS/WEEE compliant product MicroClamp, uClamp and μClamp are marks of Semtech Corporation Notes: 1)Device is electrically symmetrical Tape and Reel Specification Pin 1 Location User Direction of feed Device Orientation in Tape A0 0.69 +/-0.10 mm B0 K0 1.19 +/-0.10 mm 0.66 +/-0.10 mm Tape Width B, (Max) D D1 8 mm 4.2 mm (.165) 1.5 + 0.1 mm - 0.0 mm (0.59 +.005 - .000) 0.4 mm ±0.25 (.031) E 1.750±.10 mm (.069±.004) F P P0 P2 T W 3.5±0.05 mm (.138±.002) 4.0±0.10 mm (.157±.004) 4.0±0.1 mm (.157±.004) 2.0±0.05 mm (.079±.002) 0.254±0.02 mm (.016) 8.0 mm + 0.3 mm - 0.1 mm (.312±.012) Contact Information Semtech Corporation Protection Products Division 200 Flynn Rd., Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 © 2009 Semtech Corp. 7 www.semtech.com