Teccor® brand Thyristors EV Series 0.8 Amp Sensitive SCRs SxX8xSx Series RoHS Description New device series offers high static dv/dt and lower turn off (tq) sensitive SCR with its small die planar construction design. It is specifically designed for GFCI (Ground Fault Circuit Interrupter) and Gas Ignition applications. All SCRs junctions are glass-passivated to ensure long term reliability and parametric stability. Features • RoHS compliant and Halogen-Free • High dv/dt noise immunity • Improved turn-off time (tq) < 25 μsec • Thru-hole and surface mount packages Symbol IT(RMS) VDRM / VRRM IGT • Sensitive gate for direct microprocessor interface • Surge current capability > 10Amps Main Features Value Unit 0.8 A 400 to 800 V 5 to 200 μA • Blocking voltage ( VDRM / VRRM ) capability - up to 800V Schematic Symbol A Applications The SxX8xSx EV series is specifically designed for GFCI (Ground Fault Circuit Interrupter) and gas ignition applications. G K Absolute Maximum Ratings Symbol IT(RMS) IT(AV) ITSM Parameter RMS on-state current (full sine wave) Average on-state current Non repetitive surge peak on-state current (Single cycle, TJ initial = 25°C) I2t I2t Value for fusing di/dt Critical rate of rise of on-state current IG = 10mA IGM Peak Gate Current Value Unit TO-92 TC = 55°C 0.8 A SOT-89 TC = 60°C 0.8 A SOT-223 TL = 60°C 0.8 A TO-92 TC = 55°C 0.51 A SOT-89 TC = 60°C 0.51 A SOT-223 TO-92 SOT-89 SOT-223 tp = 10 ms TL = 60°C 0.51 A F= 50Hz 8 A F= 60Hz 10 A F = 50 Hz 0.32 A 2s tp = 8.3 ms TO-92 SOT-89 SOT-223 tp = 10 μs F = 60 Hz 0.41 A 2s TJ = 125°C 50 A/µs TJ = 125°C 1.0 A PG(AV) Average gate power dissipation — TJ = 125°C 0.1 W Tstg Storage junction temperature range — — -40 to 150 °C TJ Operating junction temperature range — — -40 to 125 °C SxX8xSx Series 1 Revised: September 5, 2012 04:52 PM ©2012 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 0.8 Amp Sensitive SCRs Electrical Characteristics (TJ = 25°C, unless otherwise specified) Symbol Value Description Test Conditions Limit IGT DC Gate Trigger Current VD = 6V RL = 100 Ω MIN. 0.5 1 15 μA MAX. 5 50 200 μA VGT DC Gate Trigger Voltage VD = 6V RL = 100 Ω MAX. 0.8 V Peak Reverse Gate Voltage IRG = 10μA MIN. 5 V Holding Current RGK = 1 KΩ Initial Current = 20mA MAX. 5 mA Critical Rate-of-Rise of Off-State Voltage TJ = 125°C VD = VDRM /VRRM Exp. Waveform RGK =1 kΩ MIN. 75 V/μs Gate Non-Trigger Voltage VD = VDRM RGK =1 kΩ TJ = 25°C MIN. 0.2 V tq Turn-Off Time TJ = 25°C @ 600 V RGK =1 kΩ MAX. 30 25 25 μs tgt Turn-On Time IG=10mA PW = 15μsec IT = 1.6A(pk) TYP. 2.0 2.0 2.0 μs VGRM IH (dv/dt)s VGD SxX8yS1 SxX8yS2 SxX8yS Unit Note: x = voltage, y = package Static Characteristics (TJ = 25°C, unless otherwise specified) Symbol VTM IDRM Description Peak On-State Voltage Off-State Current, Peak Repetitive Test Conditions Limit Value Unit ITM = 1.6A (pk) MAX. 1.70 V TJ = 25°C @ VD = VDRM RGK =1 kΩ MAX. 3 μA TJ = 125°C @ VD = VDRM RGK =1 kΩ MAX. 500 μA Thermal Resistances Symbol Rth(j-c) Rth(j-a) 1 Description Junction to case (AC) Junction to ambient Test Conditions IT = 0.8A (RMS)1 IT = 0.8A (RMS)1 Value Unit TO-92 75 °C/W SOT-223 30 °C/W SOT-89 50 °C/W TO-92 150 °C/W SOT-223 60 °C/W SOT-89 90 °C/W 60Hz AC resistive load condition, 100% conduction. SxX8xSx Series 2 Revised: September 5, 2012 04:52 PM ©2012 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 0.8 Amp Sensitive SCRs Figure 2: Normalized DC Holding Current vs. Junction Temperature 1.5 3.0 IH 4.0 1.0 IH (TJ = 25°C) 2.0 Ratio of IGT Ratio of IGT (TJ = 25°C) Figure 1: Normalized DC Gate Trigger Current For All Quadrants vs. Junction Temperature 0.5 0.0 -40 -15 +25 +65 +105 2.0 1.0 0.0 +125 -55 -35 Figure 3: Normalized DC Gate Trigger Voltage vs. Junction Temperature +5 +25 +45 +65 +85 +105 +125 Figure 4: Power Dissipation (Typical) vs. RMS On-State Current 1.0 Average On-state Power Dissipation [PD(AV)] - Watts 0.8 0.9 Gate Trigger Voltage (VGT) - V -15 Junction Temperature (TJ) - °C Junction Temperature (TJ) - °C 0.8 0.7 0.6 0.5 0.4 0.3 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180o 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.2 -40 -25 -10 +5 +20 +35 +50 +65 +80 +95 +110 0.0 +125 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 RMS On-state Current [IT(RMS)] - Amps Junction Temperature (TJ) - °C Figure 5: Maximum Allowable Case Temperature vs. On-State Current Maximum Allowable Case Temperature (TC) - oC 130 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180o CASE TEMPERATURE: Measured as shown on dimensional drawings 120 110 SOT-223 & SOT-89 100 90 TO-92 80 70 60 50 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 RMS On-state Current [IT(RMS)] - Amps SxX8xSx Series 3 Revised: September 5, 2012 04:52 PM ©2012 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 0.8 Amp Sensitive SCRs Figure 6: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-State Current (IT S M) – Amps . 20 Supply Frequency: 60Hz Sinusoidal Load: Resistive RMS On-State Current [IT(RMS)]: Max Rated Value at Specific Case Temperature 10 9 8 7 6 Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 5 4 3 0.8 2 AD evi ces 1 1 2 3 4 5 6 7 8 9 10 20 30 40 60 80 100 200 300 400 600 1000 Surge Current Duration - Full Cycle Soldering Parameters Pre Heat Pb – Free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C SxX8xSx Series Ramp-up TL tL TS(max) Preheat TS(min) 25 Peak Temperature (TP) tP TP Temperature Reflow Condition 4 Revised: September 5, 2012 04:52 PM Ramp-do Ramp-down tS time to peak temperature Time ©2012 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 0.8 Amp Sensitive SCRs Physical Specifications Reliability/Environmental Tests Test Terminal Finish 100% Matte Tin-plated. Body Material UL recognized epoxy meeting flammability classification 94V-0. Specifications and Conditions AC Blocking MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 110°C for 1008 hours Temperature Cycling MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time Temperature/ Humidity EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity High Temp Storage MIL-STD-750, M-1031, 1008 hours; 150°C Low-Temp Storage 1008 hours; -40°C Thermal Shock MIL-STD-750, M-1056 10 cycles; 0°C to 100°C; 5-min dwelltime at each temperature; 10 sec (max) transfer time between temperature Autoclave EIA / JEDEC, JESD22-A102 168 hours (121°C at 2 ATMs) and 100% R/H Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E Copper Alloy Lead Material Design Considerations Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Dimensions – TO-92 Dimension A Min Max 0.175 0.205 4.450 5.200 B 0.170 0.210 4.320 5.330 C 0.500 D 0.135 E 0.125 A SEATING PLANE C GATE ANODE G CATHODE Millimeters Max TC MEASURING POINT B Inches Min 12.70 3.430 0.165 3.180 4.190 F 0.080 0.105 2.040 2.660 G 0.016 0.021 0.407 0.533 H 0.045 0.055 1.150 1.390 I 0.095 0.105 2.420 2.660 J 0.015 0.020 0.380 0.500 H I D F J E F SxX8xSx Series 5 Revised: September 5, 2012 04:52 PM ©2012 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 0.8 Amp Sensitive SCRs Anode Gate Cathode Anode Anode Dimensions – SOT-223 Gate Anode Cathode Anode Gate Cathode Anode Inches Dimensions Gate Cathode Anode 3.3 (0.130”) 1.5 (0.059”) 1.2 (0.047”) 6.4 (0.252”) 2.3 (0.091”) (3x) Min Typ Max Min Typ Max A 0.248 0.256 0.264 6.30 6.50 6.70 B 0.130 0.138 0.146 3.30 3.50 3.70 C — — 0.071 — — 1.80 D 0.001 — 0.004 0.02 — 0.10 E 0.114 0.118 0.124 2.90 3.00 3.15 F 0.024 0.027 0.034 0.60 0.70 0.85 G — 0.090 — — 2.30 — H A— 0.181 J 4.60 — 0.264 0.276 0.287 6.70 7.00 7.30 J 0.009 0.010 0.014 0.24 0.26 0.35 E B Gate Dimensions – SOT-89 Anode Anode D Cathode C H G Anode D C E E F Gate B B Cathode G Anode Tc Measuring Point J H Gate F Cathode G Anode Gate F Cathode G C H (2.21) .087 (1.12) .044 c (3.91) .154 g (0.91) .036 g f a d (1.63) Dimensions(1.63) in Millimeters (Inches) .064 .064 f d a e b Min g Typ Max 0.181 4.40 — 4.60 0.102 2.29 — A 0.173 — B 0.090 — C g 0.055 — 0.063 1.40 D 0.155 — 0.167 3.94 E 0.035 0.047 G 0.056 c — f — 2.60 f 1.60 — 4.25 0.89 a — 1.20 0.062 1.42 — 1.57 b d — c Max Typ F c Millimeters Min H Pad Layout for SOT-89 (1.19) .047 Inches Dimension C Anode Anode D F Tc Measuring Point E J A Tc Measuri 10° MAX D Recommended Soldering Footprint for SOT223 A J Tc —Measuring — Point BAnode K Dimensions in Millimeters (Inches) A I 1.5 (0.059”) 4.6 (0.181”) Millimeters e 0.115 — 0.121 2.92 — 3.07 H 0.014 — 0.017 0.35 — 0.44 I 0.014 — 0.019 0.36 — 0.48 J 0.064 — 0.072 1.62 — 1.83 e b d e 6 SxX8xSx Series b Revised: September 5, 2012 04:52 PM ©2012 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 0.8 Amp Sensitive SCRs Product Selector Voltage Part Number Gate Sensitivity Package — 200 μA TO-92 — 200 μA TO-92 — X 200 μA TO-92 — — 200 μA SOT-223 — X — 200 μA SOT-223 S8X8TS — — X 200 μA SOT-223 S4X8BS X — — 200 μA SOT-89 S6X8BS — X — 200 μA SOT-89 S4X8ES1 X — — 5 μA TO-92 S6X8ES1 — X — 5 μA TO-92 S8X8ES1 — — X 5 μA TO-92 S4X8TS1 X — — 5 μA SOT-223 S6X8TS1 — X — 5 μA SOT-223 S8X8TS1 — — X 5 μA SOT-223 S4X8ES2 X — — 50 μA TO-92 S6X8ES2 — X — 50 μA TO-92 S8X8ES2 — — X 50 μA TO-92 S4X8TS2 X — — 50 μA SOT-223 S6X8TS2 — X — 50 μA SOT-223 S8X8TS2 — — X 50 μA SOT-223 400V 600V 800V S4X8ES X — S6X8ES — X S8X8ES — S4X8TS X S6X8TS Packing Options Part Number Marking Weight Packing Mode Base Quantity SxX8ESy SxX8ESy 0.170g Bulk 2500 SxX8ESyAP SxX8ESy 0.170g Ammo Pack 2000 SxX8ESyRP SxX8ESy 0.170g Tape & Reel 2000 SxX8TSyRP SxX8TSy 0.120g Tape & Reel 1000 SxX8BSRP xX8 0.053g Tape & Reel 1000 SxX8BSRP1 xX8 0.053g Tape & Reel 1000 Note: x = voltage, y = gate sensitivity SxX8xSx Series 7 Revised: September 5, 2012 04:52 PM ©2012 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 0.8 Amp Sensitive SCRs TO-92 (3-lead) Reel Pack (RP) Radial Leaded Specifications Meets all EIA-468-C Standards 0.02 (0.5) 0.236 (6.0) 1.6 (41.0) 0.708 (18.0) 0.098 (2.5) MAX 1.26 (32.0) 0.354 (9.0) 0.5 (12.7) Anode Cathode 0.2 (5.08) Gate 0.1 (2.54) 0.157 DIA (4.0) 14.17(360.0) Flat up 1.97 (50.0) Dimensions are in inches (and millimeters). Direction of Feed TO-92 (3-lead) Ammo Pack (AP) Radial Leaded Specifications Meets all EIA-468-C Standards 0.236 (6.0) 1.62 (41.2) 0.708 (18.0) 0.02 (0.5) 0.098 (2.5) MAX 1.27 (32.2) 0.354 (9.0) 0.157 (4.0) DIA Anode Cathode 0.2 (5.08) Gate 0.1 (2.54) 0.5 (12.7) Flat down d n of Fee Directio 25 Devices per fold 1.85 (47.0) 12.2 (310.0) 1.85 (47.0) Dimensions are in inches (and millimeters). 13.3 (338.0) SxX8xSx Series 8 Revised: September 5, 2012 04:52 PM ©2012 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 0.8 Amp Sensitive SCRs SOT-89 Reel Pack (RP) Specifications 8 mm 4 mm Ø1.5 mm 2 mm ANODE 1.75 mm 12 mm 5.5 mm GATE ANODE CATHODE 180 mm 13 mm Abor Hole Diameter 13.4 mm DIRECTION OF FEED SOT-89 Reel Pack (RP1) Specifications Ф 1.5mm 4mm 2mm 8mm CATHODE ANODE 1.75mm 12mm 5.5mm ANODE GATE 180 mm 13 mm Abor Hole Diameter 13.4 mm DIRECTION OF FEED SxX8xSx Series 9 Revised: September 5, 2012 04:52 PM ©2012 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 0.8 Amp Sensitive SCRs SOT-223 Reel Pack (RP) Specifications ∅1.5 mm 8 mm 4 mm 2 mm A 1.75 mm 12 mm 5.5 mm K A GATE 180 mm 13 mm Abor Hole Diameter 13.4 mm Part Numbering System Part Marking System S xX8 x xx xx SERIES S: SCR VOLTAGE 4: 400V 6: 600V 8: 800V CURRENT X8: 0.8A PACKING TYPE Blank: Bulk Pack RP: Reel Pack (TO-92) Embossed Carrier Pack (SOT-223) Embossed Carrier Pack (SOT-89) RP1: Embossed Carrier Pack (SOT-89) (alternate orientation) AP: Ammo Pack (TO-92) SOT89 SENSITIVITY & TYPE S1: 5µA Sensitive SCR S2: 50µA Sensitive SCR S: 200µA Sensitive SCR Line1 = Littelfuse Part Number Line2 = continuation…Littelfuse Part Number Y = Last Digit of Calendar Year M = Letter Month Code (A-L for Jan-Dec) L = Location Code DD = Calendar Date PACKAGE TYPE E: TO-92 T: SOT-223 B: SOT-89 SxX8xSx Series SOT223 TO92 10 Revised: September 5, 2012 04:52 PM ©2012 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information.